Compaq Presario 3000 Series User's Manual
Contents
1. Tuli Regulatory and Safety Notices Regulatory Notices Airline Travel Notice Use of electronic equipment aboard commercial aircraft is at the discretion of the airline Power Cords Notice If you were not provided with a power cord for your notebook or for an external power accessory intended for use with your notebook you should purchase a power cord that is approved for use in your country The power cord must be rated for the product and for the voltage and current marked on the product s electrical ratings label The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product In addition the diameter of the wire must be a minimum of 0 75 mm 18AWG and the length of the cord must be between 5 feet 1 5 m and 671 feet 2 m If you have questions about the type of power cord to use contact your Compaq authorized service provider A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it Particular attention should be paid t2. 3 TEL 0120 101589 4DS pa Brazilian Wireless Notice Este equipamento opera em car ter secund rio isto n o tem direito a prote o contra interfer ncia prejudicial mesmo de esta es do mesmo tipo e nao pode causar interfer ncia a sistemas operando em car ter prim rio Regulatory and Safety Notices 1 17 Regulatory Notices 1 18 Regulatory and Safety Notices 2 Electrostatic Discharge A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components Before handling electrostatic sensitive components discharge static electricity by using one of the methods described in this chapter Preventing Electrostatic Discharge Handling Drives Before handling a drive discharge static electricity by touching an exterior unpainted metal surface of a device that is connected to an electrical outlet by a grounding plug Do not touch the connector pins on a drive or the notebook Handling Internal Components
3. Regulatory and Safety Notices Regulatory Notices Telecommunications Device Approvals The telecommunications device in your notebook is approved for connection to the telephone network in the countries whose approval markings are indicated on the product label located on the bottom of the notebook or on the modem Refer to the documentation included with the product to ensure the product is configured for the country in which it is located Selecting a country other than the one in which it is located may cause your modem to be configured in a way that violates the telecommunication regulations laws of that country In addition your modem may not function properly if the correct country selection is not made If when selecting a country a message appears that states that the country is not supported this means that the modem has not been approved for use in this country and thus should not be used U S Modem Statements This equipment complies with Part 68 of the FCC rules Located on the bottom of the notebook or on the modem is a label that contains among other information the FCC certification number and Ringer Equivalence Number REN for this equipment If requested this information must be provided to the telephone company Applicable certification jack USOC RJ11C An FCC compliant telephone cord and modular plug is provided with this equipment This equipment is designed to be connected to the telephone network
4. The REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 The REN for this device is 1 European Union Notice CE Products bearing the CE marking comply with the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community and if this product has telecommunication functionality the R amp TTE Directive 1999 5 EC 1 12 Regulatory and Safety Notices Regulatory Notices Compliance with these directives implies conformity to the following European Norms in parentheses are the equivalent international standards and regulations E EN 55022 CISPR 22 Electromagnetic Interference E EN55024 IEC61000 4 2 3 4 5 6 8 11 Electromagnetic Immunity mM EN61000 3 2 IEC61000 3 2 Power Line Harmonics mM EN61000 3 3 IEC61000 3 3 Power Line Flicker E EN 60950 IEC 60950 Product Safety New Zealand Modem Statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network It indicates no endorsement of the product by Telecom nor does it provide any sort o
5. Numbers booklet included in English only with the notebook In Europe do not dispose of batteries with general household waste Dispose of or recycle them by using the public collection system or returning them to Compag your authorized Compaq partners or their agents Regulatory and Safety Notices 1 5 Regulatory Notices Energy Star Compliance This notebook is compliant with the U S Environmental Protection Agency EPA Energy Star Computers Program 3 0 The EPA Energy Star logo does not imply endorsement by the EPA As an Energy Star Partner the Compaq Computer Corporation has determined that the product meets the Energy Star guidelines for energy efficiency German Ergonomics Notice Compaq notebooks bearing the GS approval mark meet the requirements of ZH 1 618 German Safety Regulations for Display Work Places in the Office Sector when used in conjunction with docking bases keyboards and monitors that bear the GS approval mark Compaq notebooks in a stand alone mode are not intended for continuous use in an office environment Macrovision Corporation Notice This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limite
6. S Wireless Notice This product emits radio frequency energy but the radiated output power of this device is far below the FCC radio frequency exposure limits Nevertheless the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized Canadian Wireless Notice Operation is subject to the following 2 conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To prevent radio interference to the licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed outdoors is subject to licensing The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met Regulatory and Safety Notices 1 15 Regulatory Notices European Union Notice CE 06820 Products bearing the CE marking comply with the R amp TTE Directive 1999 5 EC EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms in parentheses are the equivalent international standards and regulations EN 55022 CISPR 22 Electromagnetic Interference N 5
7. 5024 IEC61000 4 2 3 4 5 6 8 11 lectromagnetic Immunity N 61000 3 2 IEC61000 3 2 Power Line Harmonics N 61000 3 3 IEC61000 3 3 Power Line Flicker N 60950 IEC 60950 Product Safety N 300 328 Technical requirements for radio equipment ETS 300 826 or EN 301 489 17 General EMC requirements for radio equipment mmm wm hw This product may be used in all EU and EFTA countries Regulatory and Safety Notices Regulatory Notices Japanese Wireless Notice 1 2
8. COMPAQ Regulatory and Safety Notices Compaq Notebook Series Document Part Number 307504 001 October 2002 This guide provides governmental agency information and instructions for preventing damage from electrostatic discharge 2002 Compaq Information Technologies Group L P Compaq the Compaq logo and Presario are trademarks of Compaq Information Technologies Group L P in the U S and or other countries All other product names mentioned herein may be trademarks of their respective companies Compaq shall not be liable for technical or editorial errors or omissions contained herein The information is provided as is without warranty of any kind and is subject to change without notice The warranties for Compaq products are set forth in the express limited warranty statements accompanying such products Nothing herein should be construed as constituting an additional warranty Regulatory and Safety Notices First Edition October 2002 Reference Number 800 3000 Part Number 307504 001 Contents 1 Regulatory Notices Federal Communications Commission Notice LI Modifications 1 2 Cables NS NR NN Ne Ree 1 2 Declaration of Conformity for Products Marked with the FCC Logo United States Only 1 2 Canadian Notice a sacle NG el donee ease ba 1 3 AVIS CanadieD ins NAA ANG LO PG Mah eine eke 1 3 Japanese Notice 1 3 Airline Travel Notice a 1 4 Power Cords Notice eee eee eee ee
9. When you are removing or installing internal components use the following precautions m Keep components in their electrostatic safe containers until you are ready to install them m Have everything needed for the installation within reach so that you do not need to leave the area after beginning the procedure E Use nonmagnetic tools Regulatory and Safety Notices 2 1 Electrostatic Discharge m Before touching an electronic component discharge static electricity by using one of the grounding methods described later in this chapter If you must leave the area during the procedure remember to reground yourself before resuming the procedure m Avoid touching pins leads and circuitry Handle electronic components as little as possible m If you remove a component place it in an electrostatic safe container Grounding Methods If removal or installation instructions direct you to unplug the notebook unplug it after being properly grounded and before removing a cover Use one or both of the following grounding methods m Touch an exterior unpainted metal surface of a device that is connected to an electrical outlet by a grounding plug m Use a wrist strap connected by a ground cord to the notebook chassis Wrist straps are flexible grounding straps with a minimum of one megohm 10 percent resistance in the ground cords To provide proper ground wear the strap snugly against the skin If you need more information
10. about static electricity or assistance with component removal or installation refer to the printed Worldwide Telephone Numbers booklet included in English only with the notebook to contact a Compaq authorized dealer reseller or service provider 2 2 Regulatory and Safety Notices
11. any may request that you disconnect the equipment until the problem is resolved You should only perform repairs to the equipment that are specifically discussed in the documentation included with the notebook Connection to party line service is subject to state tariffs Contact the state public utility commissions public service commission or corporation commission for information 1 10 Regulatory and Safety Notices Regulatory Notices The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a notebook or other electronic device including fax machines to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business or entity or other individual sending the message and the telephone number for the sending machine or such business other entity or individual The telephone number provided may not be a 900 number or any number for which charges exceed local or long distance transmission charges In order to program this information into your fax machine you should complete the steps outlined in the faxing software instructions These requirements apply to all fax machines and have been extended to all fax modems manufactured on or after December 13 1995 Canadian Modem Statements This equipment meets telecommunications network prote
12. ctive operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s This is confirmed by marking the equipment with the Industry Canada certification number The Department does not guarantee that the equipment will operate to the user s satisfaction Before installing the equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Regulatory and Safety Notices 1 11 Regulatory Notices Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas CAUTION Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate
13. d States Only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation For questions regarding this declaration write to Compaq Computer Corporation P O Box 692000 Mail Stop 510101 Houston TX 77269 2000 Or call Compaq at 281 514 3333 To identify your product refer to the part series or model number found on the product 1 2 Regulatory and Safety Notices Regulatory Notices If you have questions about your product that are not related to this declaration write to Compaq Computer Corporation P O Box 692000 Mail Stop 530113 Houston TX 77269 2000 Or call Compaq at Product Information Center 1 800 345 1518 Technical Support 1 800 652 6672 Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Japanese Notice VCC B
14. d viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited 1 6 Regulatory and Safety Notices Regulatory Notices Laser Safety Notices All Compaq systems equipped with laser products comply with appropriate safety standards including IEC 825 With specific regard to the laser the equipment complies with laser product performance standards set by government agencies for Class 1 laser products It does not emit hazardous light the beam is totally enclosed during all modes of customer operation and maintenance CDRH Regulations The Center for Devices and Radiological Health CDRH of the U S Food and Drug Administration implemented regulations for laser products on August 2 1976 These regulations apply to laser products manufactured from August 1 1976 Compliance is mandatory for products marketed in the United States WARNING Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product installation guide may result in hazardous radiation exposure This system is classified as a Class 1 laser product CLASS 1 LASER PRODUCT This label appears on the laser product Regulatory and Safety Notices 1 7 Regulatory Notices Laser Information Laser Type Semiconductor GaAlAs Wave Length 780 35 nm Divergence Angle 53 5 1 5 Output Power Less than 0 2mW or 10 869 W m s
15. e 1 4 Battery Notice sss ea Rn e E 1 5 Energy Star Compliance 1 6 German Ergonomics Notice a 1 6 Macrovision Corporation Notice 1 6 Laser Safety Notices 1 7 CDRH Regulations 1 7 Laser Information en 1 8 Modem Notices en 1 8 Important Safety Instructions 1 8 Telecommunications Device Approvals 1 9 U S Modem Statements 1 9 Canadian Modem Statements 1 11 European Union Notice 00 1 12 New Zealand Modem Statements 1 13 Regulatory and Safety Notices iii Wireless Notices 00 00 ce eee eee eee eee 1 15 U S Wireless Notice 1 15 Canadian Wireless Notice nnnnnnnunaanaaa 1 15 European Union Notice 0 00 1 16 Japanese Wireless Notice 1 17 Brazilian Wireless Notice 1 17 2 Electrostatic Discharge Preventing Electrostatic Discharge 2 1 Handling Drives a 2 1 Handling Internal Components 2 1 Grounding Methods a 2 2 Regulatory and Safety Notices 1 Regulatory Notices This chapter provides country specific regulatory notices and compliance information for your notebook Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are desig
16. f warranty Above all it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model nor does it imply that any product is compatible with all of Telecom s network services This equipment is not capable under all operating conditions of correct operation at the higher speeds for which it is designed Telecom will accept no responsibility should difficulties arise in such circumstances If this device is equipped with pulse dialing note that there is no guarantee that Telecom lines will always continue to support pulse dialing Use of pulse dialing when this equipment is connected to the same line as other equipment may give rise to bell tinkle or noise and may also cause a false answer condition Should such problems occur the user should not contact the Telecom Faults Service Regulatory and Safety Notices 1 13 Regulatory Notices This equipment may not provide for the effective hand over of a call to another device connected to the same line Some parameters required for compliance with Telecom s Telepermit requirements are dependent on the equipment PC associated with this device The associated equipment shall be set to operate within the following limits for compliance with Telecom s Specifications a There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initia
17. ned to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio or television technician for help Regulatory and Safety Notices 1 1 Regulatory Notices Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the Compaq Computer Corporation may void the user s authority to operate the equipment Cables Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations Declaration of Conformity for Products Marked with the FCC Logo Unite
18. o the plug electrical outlet and the point where the cord exits from the product Only an AC adapter provided with the notebook a replacement AC adapter provided by Compag or an AC adapter purchased as an option from Compaq should be used with the notebook 1 4 Regulatory and Safety Notices Regulatory Notices Battery Notice WARNING This notebook contains a lithium ion battery pack There is a risk of fire and chemical burn if the battery pack is handled improperly Do not disassemble crush puncture short external contacts dispose in water or fire or expose it to temperatures higher than 60 C 140 F Replace only with the Compag battery pack for this notebook This notebook contains an internal lithium battery powered real time clock circuit There is a risk of explosion and injury if the battery is incorrectly replaced or improperly handled Do not attempt to recharge disassemble immerse in water or dispose of it in fire Replacement should be done by a Compag authorized service provider using the Compaq spare part for this notebook N In North America dispose of nickel metal hydride or lithium ion batteries by taking advantage of the Compaq battery recycling program This program provides you with a postage paid battery pack mailer preaddressed to a reclamation facility where the metals are recycled For more information call the telephone number listed for your location in the Worldwide Telephone
19. or premises wiring using a compatible modular jack that is Part 68 Compliant See the installation instructions for details Regulatory and Safety Notices 1 9 Regulatory Notices The REN is used to determine the number of devices that may be connected to the telephone line Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call Typically the sum of the RENs of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the local telephone company If this Compaq equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice is not practical the telephone company will notify you as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes to its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service If you experience trouble with this Compaq equipment call 1 800 652 6672 If the equipment is causing harm to the telephone network the telephone comp
20. r Polarization Circular Numerical Aperture 0 45 0 04 Only authorized technicians trained by Compaq should attempt to repair this equipment All troubleshooting and repair procedures are detailed to allow only subassembly module level repair Because of the complexity of the individual boards and subassemblies no one should attempt to make repairs at the component level or to make modifications to any printed wiring board Improper repairs can create a safety hazard Modem Notices Important Safety Instructions AN WARNING When using this device basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following M Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Em Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning MH Do not use this product to report a gas leak in the vicinity of the leak Bm Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable jack or internal component EB Ifihis product was not provided with a telephone line cord use only No 26 AWG or larger telecommunication line cord in order to reduce the risk of fire Do not plug a modem or telephone cable into the network RJ 45 jack SAVE THESE INSTRUCTIONS
21. tion b The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt Where automatic calls are made to different numbers the equipment shall be set to go on hook for a period of not less than five seconds between the end of one attempt and the beginning of the next attempt The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing SO set between 2 and 10 Voice Support All persons using this device for recording telephone conversations shall comply with New Zealand law This requires that at least one part to the conversation is to be aware that it is being recorded In addition the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected the purpose for its collection how it is to be used and what is disclosed to any other party This equipment shall not be set to make automatic calls to the Telecom 111 Emergency Service 1 14 Regulatory and Safety Notices Regulatory Notices Wireless Notices In some environments the use of wireless devices may be restricted Such restrictions may apply aboard airplanes in hospitals near explosives in hazardous locations etc If you are uncertain of the policy that applies to the use of this device please ask for authorization to use it prior to turning it on U
Download Pdf Manuals
Related Search