Clifford Sabre II User's Manual
Contents
1. W Remote Controlled Courtesy Lighting For your personal safety and convenience when you remotely disarm your Sabre II the interior lights turn on and stay on until you start the engine or 30 seconds whichever occurs first W Built In Parking Light Flasher Visually confirms door lock and system status 2 Standard Features of the Sabre Il cont W Remote Door Lock Unlock Capability No more fumbling with keys in the dark or bad weather A press of a button on the remote control simultaneously arms your system and locks your vehicle s power locks Another press disarms and unlocks some vehicles require optional relays Deluxe Remote Keyless Entry in Valet Mode Use the remote to lock and unlock the car doors and remotely activate system accessories even in valet mode W High Output Insignia Siren A loud yet compact siren designed exclusively by Clifford Electronics for far superior performance features reliability and even aesthetics to all other manufacturer s look alike sound alike sirens Ultra Reliability Since sirens are installed in the engine compartment they re continually exposed to an unforgiving environment of extreme temperatures vibrations dirt dust and water which may cause the siren s electronics to fail But the entire electronic circuitry of the Sabre II siren and all of its components have been designed into the underdash control unit Consequently the electronic circuitry is shelt2. arm or disarm silently To arm or disarm silently simply press button 3 on your remote control instead of the usual button 1 12 User selectable features Your Sabre IT vehicle security system allows you to set many of its features to your own personal preferences We have made the programming procedures very simple to make a change you just press the Plain View switch a few times The system comes from the factory with all of its features pre programmed as noted in the table below and on the next page To change any of the settings use the following procedure To restore the feature to its factory setting just repeat the procedure 1 Select the feature you wish to program from the table below and on the following page Note the number of momentary spring loaded presses 2 Turn your vehicle s ignition switch to its ON position 3 Enter your valet code see page 8 on the Plain View switch 4 When the LED turns on immediately press and release the momentary side of the switch the number of times indicated in the third column of the programming table for the feature you selected to help you count you will hear a single chirp confirmation each time you press the momentary side a If noted perform the Secondary action 5 Wait 3 seconds You will hear 1 3 chirps as noted in the Program completion confirmation column and the LED will turn off Turn the ignition off 6 Repeat steps 1 5 for any other f
3. more effective and efficient than scanning Unlike scanners that sequentially transmit one digital code after another until they hit the correct code to disarm the alarm a process that may take minutes to years depending on the system s total number of codes code grabbers literally record from hundreds of feet away the code sent by your car alarm remote control Then the thief simply plays back the code when you re gone instantly disarming the alarm and unlocking the doors It s like giving the thief your car keys Non Clifford alarms can be defeated that easily In contrast Clifford systems use complex digital signal processing and unbreachable encryption to randomly change the digital code every time you use the remote control Your remote will never transmit the same code twice and the control unit will never accept the same code twice Thus the code recorded and played back by the thief s code grabber will never be accepted by your Sabre II Only ACG can make a car alarm impervious to code grabbing and only Clifford systems have ACG with Random Code Encryption How to interpret the chirps and parking light flashes When you use the remote control the system responds with chirps unless the chirp muting feature is turned on and parking light flashes These chirp flash acknowledgments mean Chirps and flashes Meaning 1 Y our system is disarmed or you have remotely exited valet mode see page 10 2 Your system is armed or
4. of the ignition switch will bypass AutoArming for one cycle perfect when fueling the vehicle AutoArming is automatically restored the next time you park your vehicle 3 Standard Features of the Sabre Il cont W Patented Remote Control Code Learning A few flicks of a switch lets you match to the system up to 4 different 3 channel and or ACG 12 channel remote controls Just as easily a lost or stolen remote control can be deleted from the system memory W Patented Smart AutoTesting Tests all triggers and sensors every time you arm and warns you if you accidentally arm the system with the hood or trunk open If there is a genuine trigger or sensor malfunction the system will specifically identify the problem thereby eliminating time consuming and costly trouble shooting W Patented Malfunction AutoBypass In the unlikely event of a trigger or sensor malfunction your Sabre II will automatically bypass the malfunction and arm all other points to continue relentless protection of your vehicle W TotalRecall W Sabre IPs memory stores the identity of the last trigger or sensor activated This provides an invaluable diagnostic means since whenever you wish the system will visually identify the last activated trigger or sensor W Patented Smart Prior Intrusion Attempt Alert When you disarm your Sabre II a special chirp and parking light flash sequence will audibly and visually alert you from a distance if an intr
5. 12 How to interpret the LED status indicator lt lt 12 High output Insignia Siren aaa aaa aa aa 12 Long term chirp silencing s s iui ea e ea une ee 4 12 Remote controlled chiro muting 0 o e 12 User selectable features 0 o 4 13 Programming table for user selectable features 13 14 EXAMPLE gt sue ia i a A a A a eRe a le A a Hae 14 Adding new remote controls 14 How to erase the codes of lost or stolen remote controls 15 1 Standard Features of the Sabre Il W Lifetime Warranty For as long as you own the car Clifford will repair or replace the control unit and remote controls free of charge see warranty card for full details W FACT False Alarm Control and Test One of many patented Clifford innovations FACT absolutely positively ends recurring false alarms W A Pair of 3 Button 3 Channel Remote Controls Fingertip command from a typical range of 100 feet W Antiscan Some car thieves use scanners that transmit one digital code after another until they hit the one code that disarms the alarm AntiScan blocks scanners to prevent disarming by anyone other than you Y Anti CodeGrabbing ACG with Random Code Encryption A code grabber is a new device that lets a thief record and capture off the air from a distance the digital code transmitted by your remote control whenever you arm your car When you leav
6. CLIFFORD Sabre II WI Table of Contents Standard Features ofthe Sabre ll 2 Welcome 4443 aoe ei amants ma la heal lo hrs min 5 Your 3 button 3 channel remote controls 5 Anti CodeGrabbing ACG with Random Code Encryption 6 How to interpret the chirps and parking light flashes 6 PIEZO Sensor NM ata andre e eo a Bo nae Ae la lan 7 Selectable starter ignition interrupt 0 o o 7 Enhanced AufoArming aaua 444384 7 AutoArming enable disable LL 7 Visual acknowledgment 7 AUTANT Q LOCK iia a he ARE MAR nl 7 Instant AutoArming bypass oaa 7 UltraSecure valetmode 8 DENNNONS 25 5 S058 a ER A Bo y ea na al 8 To enable valetmode o 9 TO OXIFVOICF Mode aos menar Ot BN Go A e E A Gk e he 9 Setting your own secret valet code 0 0 a 9 EXGMDIS pai ii a cad da A Se SE ese A AD da a 9 Remote controlled valet mode entry and exit 10 Keyless entry in valet MOde LL 10 SMOAT AUTOTESINONM ct aa he eno 10 Specific malfunction identification aooaa aa a a 10 Automatic malfunction bypass 11 IOIQIR COME LEE E Gate e dat EURE ES 11 Smart prior intrusion attempt alert ll 11 SMOANPOWSIU IM LS A pete lies a hat bee far EURE ES 11 FACT False Alarm Control and Test
7. Glass Tampering Sensor detects any attempts to break any of the vehicle windows and or the Digital Dual Zone Proximity Sensor IV a passenger compartment radar sensor particularly important for convertible and other open soft top vehicles Enhanced AutoArming If this feature is enabled and you forget to remotely arm the system will automatically arm itself 30 seconds after the vehicle doors are closed For your convenience if you re open any door s within the 30 second countdown AutoArming will restart from the beginning once all doors are closed Sabre II has these additional AutoArming features m AutoArming enable disable If you prefer you may deactivate or reactivate the AutoArming feature See User selectable features on pages 13 14 m Visual acknowledgment Five seconds after you exit the vehicle and close all the doors the parking lights will flash twice to confirm that the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm Mm AutoArm amp Lock To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User selectable features on pages 13 14 m Instant AutoArming bypass Prevents AutoArming when fueling and other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF Yow Il hear a siren chir
8. age 8 Some vehicles require optional relays to activate your vehicle s power door locks Tf your vehicle has a factory installed feature that turns off or dims the interior courtesy lights several seconds after you exit the vehicle the system cannot provide this indication 10 Automatic malfunction bypass To provide protection even if a component malfunctions the system automatically bypasses any faulty point and arms all other triggers and sensors to provide the utmost possible protection until you can have the system serviced by your local Authorized Clifford Dealer TotalRecall The system s memory records the identity of the last activated or malfunctioning trigger or sensor which allows your installer to instantly track down a malfunction To identify the trigger or sensor held in the system s memory use the following procedure 1 With the ignition OFF flick the PlainView valet switch to its latched side 2 Press button 1 to arm the system then again to disarm 3 The LED will blink 1 3 times to indicate the most recently activated trigger or sensor For convenience the blink cycle will pause and repeat a total of 5 times 4 Write down the number of blinks between pauses and refer to the chart below 1 blink Piezo Sensor 2 blinks Door trigger 3 blinks Hood or trunk trigger 4 blinks A thief tried guessing your valet code see page 8 Smar
9. e the thief replays the code to disarm the alarm and unlock your car s doors ACG with Random Code Encryption makes thieves code grabbers completely useless because each time you press the button on your remote control a different random code is transmitted yet the system will flawlessly recognize and respond to your transmitter s new code and ignore all others W Full Time Remote Panic with Automatic Door Locking and Unlocking If you feel threatened you can with just a fingertip touch on your remote control sound the siren flash the parking lights and unlock your vehicle s power door locks for quick entry into your car without fumbling with your keys If you press the panic button while driving the siren will sound the lights will flash and the doors will lock to shield you from the assailant some vehicles require optional relays to control the power locks W UltraSecure Coded Valet Mode Ensures that no thief can turn off Sabre II like they can all other brands of alarms E Optional Remote Controlled Valet Mode Entry and Exit With the optional 4 button 12 channel ACG remote you get unparalleled convenience in addition to unbreachable security With just a press of a button from 100 feet away you can enter or exit valet mode Parking light flashes confirm valet mode entry and exit W Dual Mode Chirp Silencing Your choice of either long term chirp silencing or remote controlled chirp muting whenever you wish
10. eatures you wish to program Programming table for user selectable features of Program Feature can y momentary pal completion Result 9 presses confirmation P 1 chirp OFF Change state from AE ON i z 2 chirps ON ON to OFF or vice versa AutoArm OFF 5 E 1 chirp OFF Change state from amp Lock 2 chirps ON OFF to ON or vice versa 1 chirp OFF Change state from FAST ON 6 5 2 chirps ON ON to OFF or vice versa Chirp ON 9 1 chirp OFF Change state from confirmation 2 chirps ON ON to OFF or vice versa fad allen Button 1 channel 1 code remote to 11 Pare channel 1 Press remote control button 1 1 chirp of the new remote control armidisarm has been memorized Add a new remote to Button 2 channel 2 code channel 2 12 N optional Press remote control button 2 2 chirps of the new remote control remote has been memorized accessory continued 13 of Program Feature Da y momentary rl completion Result 9 presses confirmation Add a new remote to Button 3 channel 3 code of channel 3 13 Press remote control button 3 3 chirps the new remote control silent has been memorized arm disarm All remote control codes ase ae 15 2 chirps have been erased program channels in new remote control s Valet Code 2 16 See Setting your own secret valet code on page 9 Example To change the AutoArming featu
11. ered from the harsh environment and is no longer the weakest link of the alarm system In fact the calculated mean time between failure MTBF of the Insignia Siren is 10 times better than that of conventional sirens Patented Automatic Noise Abatement Sabre II siren electronics limit alarm sounding to no more than 3 minutes even if a door is left open in the wake of an intrusion attempt This ensures against battery drain or towing of your vehicle due to noise pollution The system then automatically resets and re arms all other points to provide the utmost possible protection W Piezo Sensor An all electronic solid state vibration impact sensor that delivers the utmost reliability and provides more accurate discrimination between genuine intrusion attempts and non threatening conditions like a large truck passing by that cause other sensors to false alarm W Enhanced User Selectable AutoArming Automatically arms itself passively if you forget May qualify you for an insurance discount that could pay for the system consult your insurance company AutoArming Enable Disable You may disable or re enable AutoArming with just a few flicks of a switch AutoArm amp Lock You may set the system to automatically lock the doors every time the system AutoArms Visual Indication Two parking lights flashes signal that the 30 second countdown to AutoArming has started Instant AutoArm Bypass Just a quick turn
12. ford Electronics has long been recognized as the world s leading manufacturer of high technology vehicle security systems Buying Clifford has always meant buying the best In fact Clifford Electronics holds more patents than all other vehicle security manufacturers combined Yet despite all its sophistication you will find your Sabre II system amazingly easy to use never more difficult than a few flicks of a switch or a press of a button on one of your keychain remote controls Your 3 button 3 channel ACG remote controls The 3 button 3 channel remote controls are sophisticated miniature radio transmitters each powered by a pair of tiny lithium batteries Range is up to 100 feet Weak remote control batteries will reduce range The 3 button 3 channel remote control is the key to your system You will use your remote control to arm and disarm the system lock and unlock the doors activate the panic feature command options such as a remote trunk release headlight activation power window operation an electric garage door interface or even remote starting of the engine and heater or air conditioner TO ARM Press button 1 once You will hear two chirps and the parking THE SYSTEM lights will flash twice The dashboard LED will flash repeatedly and the car doors will automatically lock TO DISARM Press button 1 again One chirp and one parking light flash THE SYSTEM confirms disarming In addition the doors will automa
13. ger to verify that an intrusion is in progress Should the siren sound again you will know for sure that someone is tampering with your vehicle To disable FACT see User selectable features on pages 13 14 How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status Off System is disarmed and in normal operating mode i e valet mode is off On Valet mode is on the vehicle can be driven or serviced without having to disarm Flashing System is armed and protecting your vehicle Pause between flashes Either a malfunction see page 10 or an intrusion was attempted see page 11 High output Insignia Siren All the siren electronics are in the system control unit rather than the siren itself This protects them from heat dirt and exposure to the elements other alarm companies sirens are far more susceptible to failure Your Sabre II also provides these additional features m Long term chirp silencing Whenever you wish you may silence Sabre IP s arm and disarm chirps until you decide to restore them The parking light flashes will continue to provide visual confirmation of remote controlled arming and disarming See User selectable features on pages 13 14 m Remote controlled chirp muting Remote controlled chirp muting capabilities are especially valuable when parking late at night in a quiet residential area or any other time when you want to
14. itch to its ON position or start the engine 2 Flick the switch back to its center position The LED will turn off to confirm that the system is now in its normal operating mode Setting your own secret valet code Since all Clifford systems have the same factory set code it is highly advisable that you set your own valet code You may choose any 1 2 or 3 digit code that does not have any zeros You can also change your valet code whenever you want Simply write down the 1 to 3 digit code you wish to use remember no zeros in the code then perform the following steps 1 Turn the ignition on 2 Enter your current valet code the factory set code is the single digit 2 two presses of the momentary side then latched 3 Press and release the switch s momentary side 16 times To help you count you will hear a single chirp confirmation each time you press the momentary side for a total of 16 chirps 4 Immediately after the 16th chirp press the latched side of the switch enter your new code 5 Wait 3 seconds until you hear 1 chirp and the LED turns off Turn the ignition off after you hear the 1 chirp and the LED has turned off 7 VERY IMPORTANT You must immediately test your new secret valet code Turn on the ignition enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match In such a case the s
15. its A one digit code X any number between 1 9 A two digit code X Y any number between 11 99 excluding numbers with zeros A three digit code X YZ any number between 111 999 excluding numbers with zeros Remember no code can have a zero PlainView switch A rocker switch mounted on the dashboard or console The switch has three positions 1 Latched 2 Center 3 Spring loaded momentary When you press the latched side the switch remains in its pressed position When you press the momentary side the switch bounces back to the center position Entering a digit To enter a digit you tap press and release on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered followed by pressing to the latched side then returning the switch to its center position Entering a code If your code has only one digit enter the code as described in Entering a digit If your code has more than one digit just repeat the above for each digit of your code To enable valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Enter your secret valet code on the PlainView switch the LED will turn on then return the switch to its center position 3 You now have 10 seconds to press the latched position to enter valet mode The system LED will glow continually for on going visual confirmation of valet mode To exit valet mode 1 Turn the ignition sw
16. lectable features on pages 13 14 This will clear all remote control codes from the system memory Then simply program each remaining and or replacement remote control as noted in the Adding new remote controls section on page 14 CLIFFORD World Class Auto Security Sabre Il is covered by one or more of the following Clifford Electronics patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 and other patents For a Clifford Dealer near you call 1 800 CLIFFORD or visit our Internet Website at http www clifford com Copyright Clifford Electronics Inc 1996 31 701C SAB20M 396
17. p to confirm that the system will not AutoArm Your Sabre II will revert to its normal operating mode when you next start the engine 7 UltraSecure Coded Valet Mode Your secret valet code In seconds thieves can disable all other alarm brands by hotwiring the ignition and flicking an easy to find hidden valet switch Your Sabre II system has safeguards that absolutely ensure a thief cannot enable the valet mode as a way of turning off your system How To enable valet mode the driver must first enter a secret valet code on the Plain View switch If a thief tries guessing your code after three incorrect entries the siren will sound and the system will not accept any further entries for two minutes Your code will be a 1 to 3 digit number of your choosing Each digit can be any number from to 9 i e the code can be any number between 1 and 999 except those that contain a zero Whenever the system is in valet mode it overrides the AutoArming feature see page 7 and all the security features are tumed off At various times you will need to switch the system off For instance when having your car serviced washed or parked by a valet Your factory set valet code is the single digit 2 NOTE If you temporarily lose the use of your remote controls you can disarm the system by enabling valet mode Definitions m Digit A digit is defined as any number from 1 to 9 inclusive Mm Valet code A valet code may be 1 to 3 dig
18. re from its factory setting of on to off you would do the following Turn the ignition key to the ON position Enter your valet code then immediately tap and release the momentary side of the Plain View switch 4 times you ll hear a chirp each time you press to help you count to the total of 4 chirps Wait 3 seconds The system will sound one more chirp to confirm that the AutoArming setting is now off 1 chirp off 2 chirps on Turn the ignition off That s all there is to it To change the AutoArming setting back just repeat the procedure Adding new remote controls For other drivers in your family or if you wish to control Clifford systems on your other cars with the same remote control you can buy additional remote controls from any Clifford Dealer or call our Customer Service Department at 800 824 3208 and program them into the system yourself Each Sabre II will respond to as many as four 3 channel ACG and or 12 channel ACG remote controls To add a new remote control to the system use the procedures noted in the User selectable features section on page 13 and above 14 How to erase the codes of lost or stolen remote controls If one of your remote controls is ever lost or stolen you can erase its digital codes from the system memory to make sure that the missing remote control can never be used to disarm your system To do so use the Erase all channels feature see User se
19. t prior intrusion attempt alert If you hear three chirps when you remotely disarm it means that a trigger or sensor was activated in your absence When you enter the vehicle and turn on the ignition or start the engine the LED will blink 1 3 times pause then repeat the blink cycle 4 more times Count the number of blinks in one cycle and refer to the chart above SmartPowerUp Il If power to the system is ever removed SmartPowerUp II ensures the system will automatically restore itself to its previous state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while immobilizing the vehicle If your vehicle is to be serviced by a mechanic just put the system in valet mode via the remote control see Optional remote controlled valet mode entry and exit on page 10 If the mechanic needs to interrupt power your system will automatically return to its valet mode state when power is restored there will be no alarm activation and no need to provide your mechanic with your remote control and instructions on how to use it 11 FACT False Alarm Control and Test With FACT you ll never experience repeated false alarms If the Insignia Siren goes off DO NOT remotely disarm the system allow it to run for the full siren duration Before sounding the siren a second time the system automatically checks for another activated trig
20. tically unlock and the interior lights will turn on and stay on for 30 seconds or until you start the engine whichever occurs first TO SILENILY Press button 3 The system will arm or disarm with all the ARM OR DISARM indications noted above except the chirp acknowledgments TO REMOTELY Button 2 can control an optional remote trunk release or other OPEN THE TRUNK OR optional accessory such as headlight activation feature of the TO ACTIVATE A NightVision Headlight Automation System remote power DIFFERENT OPTION window operation via the SmartWindows accessory or even remote starting of your vehicle s engine and heater or air conditioner via the Clifford IntelliStart accessory Some vehicles require optional relays to activate your vehicle s power door locks TO ACTIVATE Press button 1 for 3 seconds The parking lights will flash THE PANIC repeatedly and the siren will blare for 30 seconds or until you FEATURE press button 1 again to turn it off If the ignition is on indicating you are in the car the doors will automatically lock to prevent an assailant from entering If the ignition is off the doors will unlock allowing you to enter immediately without fumbling with your keys Anti CodeGrabbing ACG with Random Code Encryption A Clifford exclusive that protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves a code grabber Code grabbers are far
21. usion attempt was foiled while you were away Your Sabre II will even identify the specific trigger or sensor that detected the intrusion attempt W Advanced CMOS Microcomputer Very large scale integration VLSI microprocessor commands and monitors all system functions yet it draws less power than the vehicle s clock so it won t deplete your car battery like other alarms W Selectable Starter Ignition Interrupt You may choose either a fault proof mode which lets you start the engine even in the unlikely event of a system malfunction or ultra secure mode that ensures a thief won t be able to start the vehicle even if he finds the system control unit and disconnects it W Hood Trunk Trigger Input For full perimeter protection of the engine compartment and trunk contents may require optional pin switches W High Luminescence LED Status Indicator Adds visual deterrence and identifies system and doorlock status W Patented SmartPowerUp Il When power to the system is disconnected the system s non volatile memory always remembers the last state armed disarmed or valet mode and returns to that state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while immobilizing the vehicle Welcome to the world of high technology vehicle security and convenience Cor on the purchase of your Sabre II Clif
22. utoTesting Each time you remotely arm your Sabre II it automatically performs an extensive test of all system triggers and sensors If the hood or trunk is open when you remotely arm the system will immediately alert you of the problem by sounding 4 chirps and 4 parking light flashes instead of the usual 2 and 2 simply disarm shut the hood or trunk and re arm to reactivate monitoring of that trigger point If a door 1s ajar or if a sensor is malfunctioning you will receive the usual 2 chirps and 2 flashes then 5 seconds later there will be 4 chirps and 4 flashes The door ajar warning will not work on vehicles that have factory delayed courtesy lights NOTE Since this is a warning indication you will hear the 4 chirps even if you have the chirp muting feature turned on m Specific malfunction identification The system can also indicate the specific malfunctioning trigger or sensor If you get the 4 chirp 4 flash signal upon arming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside your vehicle will be blinking pause then repeat 2 Count the number of blinks in one cycle between pauses for your convenience the blink cycle repeats a total of 5 times and refer to the chart below 1 blink Piezo Sensor 2 blinks Door trigger 3 blinks Hood or trunk trigger 4 blinks A thief tried guessing your valet code see p
23. you have remotely engaged valet mode see page 10 2 and then 4 Armed but there is a door open or the sensor is malfunctioning see Smart AutoTesting on page 10 3 Disarmed but there was an intrusion attempt while you were away see Smart prior intrusion attempt on page 11 4 Armed but the hood or trunk is ajar see Smart AutoTesting on page 10 Selectable starter ignition interrupt At the time of installation you can select whether your Sabre II interrupts the starter line or the ignition line To verify which line is electronically interrupted enter the vehicle close the doors arm the system while inside the vehicle then try to start the engine If the engine cranks but does not start the ignition is bypassed If it does not crank at all the starter is disabled In addition the starter ignition interrupt will be set in either Fault Proof mode which lets you start the engine even in the unlikely event of a complete system failure or Super Security mode that ensures a thief won t be able to start the engine even if he cuts all the wires or finds the system control unit and disconnects it Changing the mode requires a minor relay wiring change and installer only programming Your local Authorized Clifford Dealer can make the changes for you Piezo Sensor The Piezo Sensor detects intrusion related vibrations and impacts For an even greater level of security consider Clifford Electronics optional sensors
24. ystem will revert to the previous code mn Example of setting a new valet code Lets say you want to change the valet code from its original single digit 2 code to a double digit code of 31 You would do the following Turn the ignition on enter your current code tap the momentary side of the PlainView switch 16 times press the latched side then enter the new code momentary momentary momentary latched 3 chirps momentary latched 1 chirp center Wait 2 seconds for the the system to exit program mode 1 chirp and the LED turns off then turn the ignition off then test the new code Optional remote controlled valet mode entry and exit You can even remotely enable or exit valet mode if you have an optional Clifford 4 button 12 channel ACG remote control All you need to do is transmit channel 9 two presses of the side LevelShift button then button 1 In addition to the previously noted indications two parking light flashes will confirm that you have remotely enabled valet mode while a single flash confirms exiting of valet mode Keyless entry in valet mode You can remotely control convenience features even in valet mode For instance press button 1 as if you were disarming the doors will unlock indicated by one parking light flash and the interior lights will turn on Press it again to lock two flashes You can also use button 2 to activate an option such as remote trunk release Smart A
Download Pdf Manuals
Related Search