Home

Clarion SR5000 User's Manual

1. and bypasses those zones until it is closed Icon The parking light icon will flash twice when armed or disarmed The icon also flashes during WarnAway and at the beginning and end of remote engine start cycles The door open or trigger icon illuminates when the door trigger has been activated or the door is open and bypasses that zone until it is closed Fion The remote start icon indicates when the vehicle is remotely started 22 leo The override mode icon appears when the system is in override The remote engine start safety shut down icon indicates the vehicle may be in gear or other unsafe condition inhibiting remote start operation The battery level icon indicates the level of power remaining in the battery Icon No function S a Icon The silent arm disarm icon appears when the system has been armed or disarmed in the silent mode Icon Chirps are enabled r 1 The arm icon appears when the vehicle is armed and locked The disarm icon appears when the vehicle is disarmed and unlocked Icon Celsius Fahrenheit icon indicates the current mode of the displayed temperature either in Celsius or Fahrenheit 13 function button configurations Audible Function Button Icon Indication Lamp On 10 sec Power Saver Mode T Melody Beep Vibrate Mode 4 Vibrations 1 Beep Time Adjust for 5 Seconds 8 88 2 Beeps Mode hour Time Adjust 1 Time 8 88 Mode
2. If it becomes necessary to send the product or any defective part to Clarion the product must be shipped in its original carton or equivalent carton fully insured with shipping charges prepaid Clarion will not assume any responsibility for any loss or damage incurred in shipping ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE UNDER NO CIRCUMSTANCES SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE DIRECT OR CONSEQUENTIAL ARISING OUT OF THE USE OR INABILITY TO USE OF THE PRODUCT BECAUSE SOME STATES DO NOT ALLOW LIMI TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE THE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Should you have any difficulties with the performance of this product during warranty please call 1 800 GO CLARION or visit your local Ungo Pro Security dealer You may also contact the National Service Manager at the following address below for additional service help you may need Clarion Corporation of America Attn National Service Manager 661 W Redondo Beach Blvd Gardena Ca 90247 table of contents limited lifetime consumer warranty transceiver diagram standard transceiver con
3. Model SH3000_____ gt Owner s Guide mited lifetime consumer warrant This Ungo Pro Security system is warranted against defects in material and workmanship The main unit is covered by this limited lifetime warranty This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer This warranty is to the Original Purchaser Owner and to the original vehicle in which it was installed into This warranty is not transferable to any subsequent owner s of the product s Warranty Program Main Unit Limited Lifetime Remote Controls One year from date of purchase Siren One year from date of purchase Shock Sensor One year from date of purchase LED One year from date of purchase Override Switch One year from date of purchase The Warranty does not cover batteries or products deemed damaged through alterations or installation It also does not cover products mishandled misused neglected abused water damaged or with removed altered serial numbers PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT This warranty does not cover the costs incurred for removal or reinstallation of the main unit and or any damage to the vehicle or the vehicle s electrical system The sole responsibility of Clarion Corporation of America Clarion under this Warranty shall be limited to the repair or replacement of the product at the sole discre tion of Clarion
4. glass cracking and breaking glass produce distinctive acoustic signatures The audio sensor uses a microphone to pick up sounds then analyzes them with propri etary acoustic software to determine if the glass has been struck Backup Battery The keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery is disconnected Hood Lock Prevents the vehicle s hood from being opened without a key keeping thieves away from the systems siren the battery connections and other components under the hood Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the radar sensor Your system can react to any intrusions into this field with the full triggered sequence Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Power Trunk Release The accessory output of the system can op erate a factory power release for the vehicle s trunk or hatch Although the on board relay can control most power trunk re 45 leases sometimes an optional relay is required If the factory release is not power activated a trunk release solenoid can often be added Power Window Control Power window control can be provided by one of two systems The first system provides control that will roll up two windows automatically when the system is armed or roll two wi
5. min Alarm Clock 2 Times Set Mode hour Alarm Clock 3 Times Set Mode min Alarm Clock Music 4 Times QA 5 Selections or Power on Music 1 2 3 4 5 Selection Alarm Clock Adjust 5 Times Mode on off Timer Count Down 6 Times Adjust Mode hour 14 Timer Count Down 7 Times Adjust Mode min Timer Count 8 Times 5 Selections Down Ending Melody 1 2 3 4 5 Selection 1 Down Mode on off Remote Start On 10 times 5 Selections Melody Selection 2 1 2 3 4 5 10 Min Parking 1 Time Melody Count Down Mode 20 Min Parking 2 Times Melody Count Down Mode 30 Min Parking 3 Times Melody Count Down Mode 60 Min Parking 4 Times Melody Count Down Mode 90 Min Parking 5 Times Melody Count Down Mode 120 Min Parking 6 Times gt Melody Count Down Mode Parking Count Down 7 Times Melody Off Mode Alarm Clock Mode a Melody On Off Celsius Fahrenheit AUX or Melody Select Mode This function will operate in the disarmed state only The button will advance the selection upward The K but ton will advance the selection downward or select the off setting 15 Be sure to hold down for five seconds prior to entering timer clock adjust mode operation Dress once to have the alarm clock on Press twice to have the alarm clock off remote operation The 554 remote start syst
6. A S K Receiver One four button two way transceiver One four button remote Two stage shock sensor Six tone programmable siren Red status LED indicator light Push button override switch Your warranty registration Starter Kill Shut down toggle switch Congratulations on the purchase of your combination remote engine start alarm system Due to the complexity of this system it must only be installed by an authorized dealer Installation of this product by anyone other than an authorized dealer voids the warranty By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features warning safety first The following safety warnings must be observed at all times warning THIS SYSTEM PROVIDES REMOTE NOTI FICATION OF SECURITY SYSTEM TRIGGER EVENTS CONTACT POLICE OR SECURITY PER SONNEL IMMEDIATELY NEVER CONFRONT A CAR THIEF OR VANDAL gt Due to the complexity of this system installation of this product must only be performed by an authorized dealer gt When properly installed this system can start the vehicle via a command signal from the transceiver Therefore never operate the system in an enclosed area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partially enclosed area or when having the vehicle serviced the remote engine start system must be disabled using the installed toggle switch It i
7. Following are descriptions of the many ways this system protects the vehicle Included are descriptions of the types of alarm pages and how to interpret them gt Door Locks if available The system will automatically lock the vehicle doors when armed Starter Kill The starter kill will prevent the vehicles starter motor from cranking when armed Status LED The status LED blinks approximately once per second as a visual deterrent to potential vehicle theft Warning Light impacts trigger the warning signal When triggered the siren chirps and the parking lights flash for a few seconds Triggered Sequence Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for the programmed duration Progressive Response If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your transceiver if you inadvertently open the door while the system is armed while still providing instant response even if the door is immediately closed Ignition Trigger Turning on the ignition key will trip the same progressive response as opening a door 19 warning response description A warning Response consists of an alarm page along with the responses described below gt Sho
8. ignition is turned on Some states have laws against sirens sounding in moving cars gt Forced passive arming on or off If your security system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open Forced passive arming ensures that the system will be armed if a door has accidentally been left ajar when leaving the vehicle note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational gt Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Pro Security Programmer the full triggered response can be programmed for any duration ranging from 1 to 180 seconds gt Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly on
9. three times followed by a long chirp Zone 4 is now bypassed Press a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now bypassed Press a fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed Continued pressing of will begin the Remote Sensor Bypass cycle over again 23 note Remote Sensor Bypass only applies to a single arm ing cycle Once the system is disarmed and then re armed all the zones will be active again disarming Press to disarm the system The vehicles lights will flash twice the doors will unlock the siren will chirp twice and the status LED will turn off The transceiver will beep twice or vibrate and the disarm icon 29 will be displayed on the LCD If the siren chirps and the transceiver beeps four or five times when disarming the system is reporting a triggered response or the false alarm prevention circuitry was activated while armed Refer to the Diagnostic section of this manual for information about disarm diagnostics and how to interpret them silence alarm without disarming 24 This a feature makes it possible to silence and reset the system while it is triggered without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds press any button on the transceiver to stop the page then
10. up 41 power saver mode 41 programming options 42 security amp convenience expansions 45 glossary of terms 46 o I Ic I eo IIr IsO lv RO ca a jo jos oO cy TER TEN TEN TEN TEN LEON TEN TEN TEN TEN TEN el a 4 v N o le fe lle o 8 El8 121 El E El a alfliSCtEIVET CONMHQUraliOT i a ie O a Vehicle Interior Temperature Indicator Numeric Display AM PM Indicator Alarm Clock Mode Indicator Timer Function Indicator Transmit Range Indicator Transmission Indication Vibrate Beep Mode Indicator Power Saver Mode Indicator 10 Remote Engine Start Timer Mode Indicator NO GN Q9 N 00 IN 11 No Function 12 No Function 13 Full Trigger Shock Sensor Indicator 14 Hood Trunk Open or Trigger Indicator 15 Parking Light Indicator 16 Door Open or Trigger Indicator 17 Arm Lock Button 18 Disarm Unlock Button 19 Remote Engine Start Indicator 20 Hood Trunk Open or Trigger Indicator 21 Panic Mode Button 22 Override Mode Indicator 23 Remote Start Neutral Safety Wire Shutdown Indicator 24 Battery Level Indicator 25 Auxiliary Button 26 No Function 27 Silent Arm Disarm Mode Indicator 28 Audible Chirp Indicator 29 Arm Disarm Indicator 30 Function Button 31 Celsius Fahrenheit Indicator edo ii Y Y Y Y Y Y Y Y Y Y Y Control module
11. vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a open zone notification Once the light turns off however the security system resumes normal monitoring disarming diagnostics Extra chirps that are heard when disarming the system are defined as follows If four chirps are heard when disarming the system a triggered response was generated in your absence If five chirps are heard when disarming the system a zone was trig gered so many times that the false alarm prevention circuitry has bypassed that zone In either case the status LED and transceiver LCD will indicate which zone was triggered see Table of Zones section The security system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time that the ignition is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below Action Arm Arm Disarm Disarm Disarm Number of Chirps Remote Beeps 1 1 3 second delay 1 Description System armed System armed with open zone notification System disarmed System disarmed with previous alarm System disarmed false alarm prevention circuitry active 37 table of zones A zone is represented by the LED flashes used by the system to identif
12. attery saver mode which will drop power consumption on the trans ceiver battery to zero when the alarm is inactive or disarmed standard icon configurations 10 Icon The vehicle interior temperature icon displays the temperature of the inside of the vehicle when prompted The numeric display icon will show the hours and minutes The AM PM icon indicates the time before or after noon The alarm clock mode icon indicates that the alarm clock mode is active Icon The timer function icon flashes during timed functions including parking timer The transmit range indicator icon stays visible as long as the system is within operating range Icon The remote transmission indicator icon displays when the trans ceiver is transmitting a signal Icon The vibrate beep mode icon appears when the transceiver is set to vibrate mode Icon The power saver mode can be turned on or off with the trans ceiver This icon displays the status Icon The remote engine start timer mode icon indicates the 24 hour autostart feature is active and automatically remote starts 24 hours from the time activated 11 12 Icon This icon has no function Icon No function A eo The full trigger shock sensor icon indicates that the shock sensor has been triggered by a hard shock The hood trunk open or trigger icon illuminates when the hood or trunk trigger has been activated or the hood or trunk is open
13. ck Sensor Light impacts to the vehicle will flash the vehicle lights and chirp the siren for a few seconds Remote Control Notification Ten quick beeps or one vibration Remote Control LCD The full trigger alert icon 28 will dimly illuminate for two seconds The transceiver will enter Page Recognition Mode and operate alarm page alerts note Icons 13 and 14 represent alarm system zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configurations section triggered response description A triggered response can be activated by any of the triggers listed 20 below and consists of an alarm page along with the response described for each trigger The default triggered response dura tion is 30 seconds but can be programmed from 1 180 seconds by your installer with the Pro Security Programmer gt Sensor Trigger Heavy impacts to the vehicle will instantly sound the siren and flash the lights for the programmed duration and report Zone 2 gt Door Trigger If a door is opened the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and report Zone 3 The three seconds allow the user time to disarm the system with a minimum of noise should a door be opened inadvertently while the system is armed Hood Trigger Opening the hood will sound the siren flash the lights for the programmed durat
14. e half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter will be disabled To start the 43 car it will be necessary to disarm the system with the trans ceiver It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the override switch the programmed number of times AED is also disabled when the system is in override mode note This feature will only function if the starter kill relay has been installed gt Siren tones and arm disarm chirp volume The output of the siren consists of six different tones in sequence Any of these tones can be eliminated by the dealer resulting in a unique easily identifiable siren sound The arm disarm chirps can be either full volume or 6 decibels quieter than the full alarm blast gt Using the Pro Security Programmer the engine can be programmed to run for any duration ranging from 1 to 60 minutes 12 minutes is the default After the programmed run time the engine will shut down and will not restart unless in Timer Mode gt While the remote start system is running the engine the parking lights of the vehicle can flash on and off or come on and light steadily security amp convenience expan SOS _ _ oo Listed below are some of the many expansion options available Please consult your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass
15. em operates at 434 MHz and incorpo rates an A S K out board two way transceiver The high frequency combined with Binary Data communication achieves superior range with two way communication system signal paging features 16 A page is the signal the control module sends to the transceiver as confirmation of receipt of a command or alarm system status When the transceiver receives a page it will generate a page notifi cation to the user notifications are audible beeps or transceiver vibration and the LCD icons will display the current system status Command Page When a command arm disarm remote start or auxiliary channel from the transceiver is sent and received the system will send a command page back to confirm receipt Page Recognition Mode The transceiver will leave a zone icon illuminated when it has received a triggered response and will wait for violation recogni tion To clear the LCD information and alarm page alerts turn the ignition on and then off active arming Press for one second to arm the system The vehicles lights will flash once the doors will lock the siren will chirp once and while the system is armed the status LED will blink approxi mately once per second to indicate the system is actively protecting the vehicle The transceiver will beep once or vibrate The arm icon 29 will appear and remain displayed on the LCD Open Zone Notification If the siren chirps again the
16. erate a vehicles motor in a garage or other closed off area Breathing the exhaust from the vehicle is hazardous to your health Never acti vate the remote engine start in an enclosed space When you are ready to drive the vehicle 1 Insert the ignition key and turn it to the ON not the START lt position 2 Press the brake pedal Ys A No 2 To shut down the remote start and turn off the engine While the vehicle is running during remote start operation the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut down inputs The brake pedal is pressed The hood is opened The shutdown toggle switch is put into the OFF position Y Y Y Y The pre programmed run time 12 24 or 60 minutes has elapsed M Transceiver buttons and are pressed again to start the vehicle Y The transceiver will generate a page notification with a unique melody or vibrate and the remote start icon 19 will turn off when the remote start shuts down override take over The Override Take Over feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate controls on To perform Override Take Over l Before turning off the engine simultaneous
17. figurations what is included important information warning safety first system maintenance fec id notice CAUTIONS Las nt transceiver functions standard button configurations standard icon configurations function button configurations remote operation system signal paging features using your system ACHIVE AMINO ss Sone awk ews PASSIVE AEMING ic e vehicle protection warning response description triggered response description arming disarming while driving remote sensor bypass GISALMING satis anios ra silence alarm without disarming disarming without a transceiver emergency override silent arm disarm 16 pamemode ito ier 27 override mode 27 remote engine start 28 override take over 31 settino the Clock sora wes 31 temperature check mode 32 safety atinado 33 starter anti grind circuitry 33 disabling the remote engine start A arena aise 33 over and under rev protection 34 shut down inputs 34 false alarm prevention circuitry 34 AA yg see ruer rarr EIAN 36 arming diagnostics 36 disarming diagnostics 36 system status chirps 37 table Of ZONES erario 38 interpreting zone diagnostics 38 anti code grabbing 39 individual recognition 40 power
18. ion and report Zone 1 Trunk Trigger Opening the trunk if connected will instantly sound the siren and flash the lights for the programmed duration and report Zone 4 Ignition Trigger If the ignition is turned on the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and report Zone 5 When a triggered response is activated the transceiver will gt gt Repeat four quick beeps or vibrate for 15 seconds The zone icons will turn on and remain on until the ignition is turned on and then off clearing the page alert The transceiver will enter page recognition mode and generate alarm page alerts note Icons 13 14 16 and 20 represent alarm system triggered sequence zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configurations section 21 arming disarming while driving 22 The alarm system can operate while the vehicle is being driven for added safety when driving through areas of questionable security The alarm will only respond to the door trigger inputs and the starter kill will be activated Arming while driving Press for two seconds while the vehicle is running The vehicle s siren will chirp the lights will flash and the doors will lock if unlocked Then a open zone notification chirp will be heard and the status LED will blink in a pattern of five indi cating the igni
19. ll remain bypassed The vehicle doors are protected by false alarm prevention circuitry differently If your security system is triggered by an open door for three full cycles the system will bypass the doors until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the false alarm prevention circuitry program ming can cause zones to be bypassed and appear to stop working 35 x 36 The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering the system will generate a open zone notification This means that the secu rity system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal monitoring For example if your
20. ly press and M I release and on the transceiver A remote start page notification with a unique melody or vibration will be generated and the LCD will display the remote start icon 19 as long as the vehicle is running Then wait three seconds 2 Turn the ignition key to the OFF position The engine will stay running 3 The engine will run until the pre programmed time elapses or a shut down input is received See the previous remote engine start section for a complete list of shut down inputs setting the clock To set the clock press and hold for five seconds the trans ceiver will chirp twice and the hour selection will start flashing Immediately press to advance the hour selection or ES to reverse the hour selection Once the correct hour is displayed press again and the minute selection will start flashing 31 Then press to advance the minute selection or to reverse the minute selection Once the correct time is displayed simply stop pressing any buttons for 10 seconds and the trans ceiver will automatically exit the clock mode temperature check mode 32 This system will report the interior temperature of your vehicle with the press of two buttons To activate the temperature display press and simultaneously You will hear a melody and the interior temperature will appear on the LCD screen for five seconds note If the ignition is on the temperature check clock mode will not work
21. n gt To review zones that have been bypassed press 10 seconds after arming the system The bypassed zones will flash until the alarm is reset by the ignition gt When a previous alarm notification is generated upon disarming the triggered zones will flash continuously on the transceiver LCD until reset by the ignition gt To review the zones that have been triggered press the Ej button They flash five times then turn off The receiver and remotes use a mathematical formula called an algorithm to change their code each time the transceiver is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the transceiver in sync with the control unit even if you use the transceiver out of range of the vehicle How 39 40 ever if the transceiver has been pressed many times out of range of the vehicle or the battery has been removed it may fall out of sync with the control unit and fail to operate the system To re sync the transceiver simply press several times within range of the vehicle The alarm will automatically re sync and respond to the transceivers normally Individual recognition is a revolutionary new feature Using a Pro Security Programmer hand held programming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each transceiver that is
22. ndows down by using the remote The second system will roll two windows both up and down This second system also provides one touch switch operation glossary of terms 46 Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the microprocessor which monitors your vehicle and controls all system functions Starter Kill An automatic switch controlled by your system that prevents the vehicles starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in override mode or if the starter interrupt switch itself fails Your system has feature ready circuitry for the starter interrupt however installation may require additional labor Input A physical connection to the system n input can be provided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights LED A blue light mounted at a discretionary location inside the vehicle It is used to indicate the status of your system and as a visual deterrent Protected Entry A protected entry is a door hood trunk sliding window camper door or any other opening into the vehicle that can be connected to the alarm with a switch Shock Sensor This system has a dual zone shock sensor This sensor is mounted in the vehicle and designed to pick up impacts to the vehicle or glass Lighter impacts
23. nected to the vehicle to sense engine speed This wire must be connected in order for over and under rev protection to work shut down inputs This security system uses several inputs to shut down the remote start operation of the motor or prevent remote start if certain inputs are active The two most important are hood and brake inputs The hood input will prevent the motor from starting as well as shut it down any time the hood is opened The brake pedal will shut down the motor at any time during remote start operation as well as preventing the remote start from activating while it is being pressed false alarm prevention circuitry Your system has false alarm prevention circuitry It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackham mers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm false alarm prevention circuitry will interpret those triggers as false alarms After the third trigger the false alarm prevention circuitry ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the security system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continually being triggered wi
24. ntinuously while accessing Channel 2 output Button The panic feature is controlled by pressing this button for two seconds Press again to disable panic mode Button The LCD backlighting will turn on when pressed for less than one second when held for more than five seconds the transceiver will enter adjustment mode allowing the setting of the clock timer mode and audible melody selection For more information please refer to the Function Button Configurations section of this guide and Buttons The remote engine start function of the system is controlled by pressing these buttons simultaneously for one second and Buttons When pressed simultaneously these buttons activate remote engine start timer mode engaging the remote engine start func tion every 24 hours and Buttons When pressed simultaneously these buttons display the internal temperature of the vehicle on the LCD E and Buttons The numeric display toggles between the time of the day and the alarm clock when these buttons are pressed simultaneously F and Buttons Press these buttons simultaneously to activate the parking timer Each additional press will toggle through the available options 10 min 20 min 30 min 1 hour 1 5 hours 2 hours and off and Buttons When pressed simultaneously these buttons toggle between beep notification and vibrate notification and Buttons When pressed simultaneously these buttons activate b
25. observing the correct polarity When power is returned the transceiver will light all icons in the LCD and generate all beeper tones once fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device caution This product is designed for fuel injected automatic transmis sion vehicles only Use of this product in a standard transmission vehicle is dangerous and contrary the product s intended use J a f j a The transceiver buttons are used to send commands to the system The descriptions below reflect the standard configura tion for this system The buttons can be custom configured for the user s specific needs by the installer standard button configurations Button The System Arm Lock and Remote Sensor Bypass functions are controlled by pressing this button for one second Button The System Disarm Unlock and the capability to silence the alarm without disarming These functions are controlled by pressing this button for one second Button Channel 2 output is controlled by pressing this button for three seconds Hold the button down co
26. press a on the transceiver to stop the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visually checking the vehicle oF na Pressing after resetting the system will disarm the system Pressing any button to clear the transceiver page and within the first six seconds will stop the trigger response and disarm the system The six second timer is there for your convenience in case the system was accidentally triggered disarming without a transceiver emergency override If your transceiver is lost or damaged you can manually disarm your vehicle security system To disarm the system without a transceiver you must have the vehicle s ignition key and know where the override switch is located Be sure to check with your installer at the time of installation for both the location and the preset response 1 5 presses of the override switch To disarm the security system turn the ignition to the ON posi tion Press the override switch the preset number of times one to five times within five seconds The factory preset is one After five seconds the system will disarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of override switch Number of Presses 25 important The override switch can be programmed to respond to 1 5 pre
27. s the user s sole responsibility to properly handle and keep out of reach from children all transceiver to assure that the system does not unintentionally remote engine start the vehicle THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole respon sibility of the user gt Use of this product in other than a fuel injected automatic transmission vehicle is contrary to its intended mode of operation may result in property damage personal injury or death 1 Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the neutral safety feature of the vehicle periodically checked wherein the vehicle must not remotely start while the car is in gear This testing should be performed by an authorized dealer in accordance with the Safety Check outlined in the product installation guide If the vehicle starts in gear cease remote start operation immediately and consult with the authorized dealer to fix the problem gt After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle star
28. safety features rk rs This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components starter anti grind circuitry Whenever the vehicle is remote started advanced anti grind circuitry prevents the starter from engaging even if the key is turned to the start position This prevents damage to the starter motor if the key is turned to the start position during remote start operation note Anti grind circuitry only works when the remote start system is operating the motor and the starter kill relay is installed disabling the remote engine start system This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the shutdown toggle switch to the OFF position The switch can be installed in a location of your choice Check with your installer for recommended locations Location of Shutdown Switch 33 34 over and under rev protection The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the programmed levels This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race note The system uses a wire con
29. sive arming by using override mode This is very useful when washing the vehi cle or having it serviced In override mode the security system will not arm even with the transceiver but all convenience func tions door locks trunk release remote starting etc will continue to work normally To enter or exit override mode Turn the ignition on 1 2 Turn the ignition off 3 Press and release the override switch within 10 seconds 27 28 The status LED will light solidly if you are entering override mode and it will go out if you are exiting override mode The transceiver will not generate a page notification when entering or exiting override mode using the override switch To enter or exit override mode using the transceiver 1 Open any vehicle door Press 2 3 Press 4 Press again The status LED will light solidly if you are entering override mode and it will go out if you are exiting override mode The transceiver will generate alarm disarm page notifications since the observing buttons are used when entering and exiting over ride mode The status LED is the only way to ensure the system has entered exited override mode remote engine start This feature allows you to remotely start and run your vehicle for a programmable period of time This makes it possible to warm up the engine as well as adjust the interior temperature of the vehicle with the climate control system If in
30. sses for the disarm function You must check with the installer to verify the programming for your individual unit silent arm disarm 26 To temporarily turn off the arm or disarm chirps use silent arm disarm Simply press for less than one second before arming or disarming and the confirmation chirp s will be elim inated for that one operation only When silent arm disarm has been used the silent arm disarm mode icon will indicate silent arm disarm If you want the arm disarm chirps turned off permanently your dealer can do this for you note The warning response to lighter impacts is bypassed if the system is armed using silent arm disarm This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering Only the warning response is bypassed panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your transceiver Just press 0 for two seconds and you will enter panic mode The siren will sound and the parking lights will flash To stop panic mode press on the transceiver again note Once panic mode has been entered the siren will sound for 30 seconds The transceiver will beep or vibrate continuously when the system enters panic mode The transceiver will not generate a page notification when panic mode is exited override mode You can prevent your security system from pas
31. system enters over ride mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a one hour period while the system is in override mode the LED will shut off If the system remains in override mode the LED will come back on the next time the ignition is turned on and then back off 41 j Programming options control your system s normal operational 42 set up Most options do not require additional parts but some may require installation labor The following is a list of the programmable options with the factory settings in Bold gt Active arming transceiver only or passive arming auto matic arming 30 seconds after the last door has been closed Arming disarming siren chirps on or off The ignition controlled door lock feature on or off When this feature is programmed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off If your installer is programming the security system with the Pro Security Programmer ignition lock and unlock are independent features that can be programmed separately Passive door locking with passive arming or active door locking only when arming with the transceiver Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Panic mode enabled disabled when the
32. terior heating or cooling is desired the climate controls must be preset and the fan blower must be set to the desired level prior to remote starting the vehicle important 1 Never remote start your vehicle when the keys are in the ignition except when performing Override Take Over and 2 Never start the vehicle if it is not in either PARK or NEUTRAL To remote start the vehicle l T Simultaneously press and on the transceiver for one second The parking lights will flash to confirm that the vehicle will attempt to start A remote start page notification with a unique melody or vibration will be generated and the LCD will display the remote start 19 icon as long as the vehicle is running note The transceiver will generate a Page Notification with a different unique two tone beep or vibrate and the remote start 19 icon will turn off when the remote start shuts down In gasoline vehicles the engine will start four seconds after the parking lights flash In diesel vehicles the engine will start when the WAIT TO START indicator on the vehicle s dash goes out Once the vehicle has started it will run for the pre program med period of time either 12 24 or 60 minutes see Programming Options section of this guide or until a shut down input is triggered When using the Pro Security Programmer the run time can be programmed from 1 60 minutes 29 30 important It is unsafe to op
33. tion is on The transceiver will beep once or vibrate and the arm icon 29 will be displayed on the LCD Disarming while driving A Press on the transceiver or simply turn off the ignition to disarm the system The lights will flash twice the doors will unlock the siren will chirp twice and the status LED will turn off The transceiver will beep twice or vibrate The disarm icon 29 will be displayed on the LCD note If the transceiver received a warning or triggered response page while armed the first press of the unlock button will clear the page alert A second press will turn the siren off and a third press will disarm the system remote sensor bypass Remote Sensor Bypass allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section of this guide Pressing only in standard configuration again within five seconds of arming the system will activate the Remote Sensor Bypass feature Each press of will select a different security level and the transceiver will beep or vibrate once and the arm icon 29 will flash on the LCD The system will respond as follows gt Press once The siren chirps once and the system is armed Press a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed Press a third time within five seconds The siren chirps
34. transceiver beeps again and the status LED blinks in a pattern a protected entry or sensor input is active and its icon will be displayed on the transceiver LCD This is called open zone notification Refer to the Diagnostic section of this manual for further information 17 passive arming The system can be programmed to arm automatically This is 18 called passive arming In passive arming mode the system will arm itself 30 seconds after the user exits the vehicle and closes all protected entry points Passive arming sequence l Ze 3 Turn the ignition off and exit the vehicle Close all protected entry points doors hood trunk The status LED will blink at twice its normal rate indicating the system has begun the 30 second countdown After 20 seconds the siren will chirp once unless programmed off as an audible indication that the system is about to arm At 30 seconds the system will fully arm itself At this time the lights will flash and the doors will lock if programmed for passive locking The LED will flash and transceivers arm icon 29 will appear and remain displayed on the LCD However the transceiver will not chirp or vibrate confirmation note The system will not passively arm if a protected entry or sensor is active unless forced passive arming has been programmed on Refer to the Programming Options section for information about forced passive arming vehicle protection
35. ts when performing the Neutral Safety Shutdown Circuit test the remote start unit has not been properly installed The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear All instal lations must be performed by an authorized dealer OPERA TION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE UNGO WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS system maintenance This system needs no specific maintenance beyond transceiver battery replacement The transceiver is powered by a 1 5V AAA battery The Battery Level indicator has three level indicators that serve as a visual indication of battery charge When the battery reaches a low charge level that requires replacement the transceiver will generate a single notification chirp and the Battery Level indi cator will flash continuously DDN p FULL REPLACE EMPTY Battery Replacement Gently pull the battery cover release tab then slide the door down to expose the battery and remove the expired battery Place the new battery into the transceiver
36. used with the system Then whenever a specific transceiver is used the system will recall the settings assigned to that transceiver Individual recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user note Individual recognition cannot be programmed without a Pro Security Programmer and the necessary software Check with your dealer for more information power uo s S This system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in override mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in override mode This applies to all states of the system including arm disarm and override mode power savermode Your system will automatically enter power saver mode while armed or in override mode after a period of time in which no operation has been performed This lowers the current draw on the vehicle s battery Power saver mode takes over under the following conditions gt Power saver when the system is armed After the system has been armed for 24 hours the LED will flash at half its normal rate decreasing the system s current draw gt Power saver in override mode When the
37. will generate a warning response while harder impacts will generate a full trigger response Remote Control A hand held device that operates the various functions of your system and communicates system status Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of the siren sounding and parking lights flashing for the programmed duration Override Switch A small push button mounted at a discretionary location inside the vehicle It is used to override the starter inter rupt when a transceiver is lost or damaged or to enter or exit override mode and for programming when the Pro Security Programmer is not available 47 48 Warning Response Lighter impacts to the vehicle will generate the warning response It consists of several seconds of siren chirps and parking light flashes Zone zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone Get Started Get Protected A CLARION COMPANY Ungo Pro Security 661 W Redondo Beach Blvd Gardena Ca 90247 800 GO CLARION 2003 Directed Electronics Inc GSR5000_ 11 03
38. y a particular type of input Standard input assignments are listed in the following table ZONE Number of LED Flashes DESCRIPTION 1 Instant trigger hood pinswitch 2 Instant trigger a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger for optional sensors 5 Ignition trigger 38 interpreting zone diagnostics Warning responses are not reported by the arming or disarming diagnostics If you receive a open zone notification when arming or a previous alarm notification when disarming look at the LED or transceiver LCD Active or triggered zones will be indi cated by a pattern of blinks by the LED or the transceiver icon will indicate the triggered zone Example If Zone 3 was active or triggered the LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on and the door icon 9 will be displayed on the transceiver note Your system stores the last two triggered zones in memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details gt Arming and disarming diagnostics including warning responses are reported by the transceiver on the LCD gt When an open zone notification is generated during arming the transceiver LCD will flash until the alarm is reset by the ignitio

Clarion SR5000 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents