Clam Corp Fish Trap 8063 User's Manual
Contents
1. opinion may improve the performance and efficiency of the product It shall not be obligated to make such alterations or modifications to products already in service 122. show drivers your whereabouts Night time exterior reflectors must be visible to reduce risk of collisions Warranty Clam Corporation Inc warrants to the original retail purchaser that all Clams are free from manufacturer s defects for one 1 year from the date of the original purchase Warranty does not cover cracked windows tent tears broken or bent hoops due to high wind weather conditions or unattended use Clam Corporation will replace or repair any part found defective within the one 1 year time limit All parts must be returned to Clam Corporation Inc Before returning any parts you must first call or write and acquire a return authorization All returns must be returned postage prepaid and include the original cash register receipt date and purchase price Limitation of Liability It is expressly understood that Clam Corporation liability for its products whether due to breach of warranty negligence strict liability or otherwise is limited to the repair of the product as stated above Clam Corporation is not liable for any injury loss damage or expense whether direct or consequential including but not limited to loss of use income profit or damage to material arising in connection with the sale installation use of inability to use or the repair or replacement of Clam Corporation products Clam Corporation reserves the right to make alterations or modifications in its products at any time which in its
3. Four 1 4 Thin Locknut p n 101082 1 1 8 Dia Tube Cap p n 101429 p n 101424 Rear Seat Bracket Ea Latch Clip La FI pa FF p n 101442 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 Step Six Note direction of Spring Buttons on Canopy Poles 1 4 Dia X 3 Long Phillips Screw p n 101487 1 X 2 Rectangular Tube Cap p n 101430 1 4 Dia X 3 4 Long Phillips Screw p n 101088 1 4 Dia X 1 1 4 Long Phillips Screw p n 101480 Canopy Pole 4 p n 101069 Tube Spacer Cap p n 101083 Left Canopy Bracket shown p n 101584 Right Canopy Bracket p n 101585 Voyager Base p n 101612 1 4 Flat Washer p n 101081 Porch Pole pin 101121 e l 1 4 Thin Locknut al p n 101082 1 X 2 Rectangular Support Tube p n 101438 e 6 Step Seven Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends of each Canopy Hoop Pole Support the first Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles the shorter of the two provided lengths Lean the two remaining Canopy Hoop Poles against the first Rear Adjustable Spreader Pole p n 101580 Canopy Hoop Pole p n 101482 Drape the Tent over the supported hoops then go insi
4. Model No 80643 Height 70 inches Length 93 inches Width 74 inches Weight 110 Ibs p n 108098 Clam Customer Service Information NOTICE ONCE USED THIS SHELTER CANNOT BE RETURNED TO THE STORE IF YOU HAVE A WARRANTY CLAIM PLEASE CONTACT CLAM CORP CUSTOMER SERVICE BY EMAIL INQUIREY OR DIRECT BY CALLING m Customer Service Hrs 9am to 4pm Mon Fri Central Standard Time Clam Corporation Inc 15600 28 Ave N Plymouth MN 55447 Phone 763 231 4120 Fax 763 231 4121 Email customerservice clamcorp com Website www clamcorp com Take a closer look if Gu 7o RATION N dl La 2005 Clam Corporation Inc Manual 101523 CORP Slide Block p n 101048 Step One ERE x 1 Long Philips Screw p n 101147 1 4 Thin Locknut J p n 101082 1 1 2 X 1 3 4 Aluminum Angle X 9 Long p n 101146 6 Square Swivel Plate q p n 101399 1 4 Hex Head Bolt X 1 2 Long p n 101470 1 4 Dia Hex Head Bolt X 1 2 Long p n 101470 Step Three Cloth Accessory Hammock Pa shipped packed with Tent 3 p n 101466 1 4 Thin Locknut p n 101082 Front Seat ME p n 101420 1 1 8 Dia Tube Cap gt p n 101429 1 4 Dia X 1 3 4 Long Phillips ia p n 101486 _ 1 1 8 Dia Tube p n 101652 Assembly from Step
5. Tilt the complete assembly downward so that the Rear Seat Bracket lands upon the Support Tube Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket Secure the position of the Latch Clip by pushing it into the two holes located above the horizontal slot of the Rear Seat Bracket To finish place the Center Console on the front Base ledge and Support Tube and your assembly process is complete WARNING ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITON DURING USE FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM Latch Clip Rear Seat Bracket Support Tube Center Console p n 101458 Tow Rope p n 101095 Knot the ends of rope after routing through the predrilled holes in base 11 Tips for Use Folding and transporting your Fish Trap is easy Unsnap the Roof Spreader Poles Rear Spreader Poles and Front Spreader Poles Lay them in the bottom of the base Push the spring buttons and retract each hoop starting with the rear hoop and working towards the front Rotate all retracted hoops to the resting position Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport Cover with the Travel Cover an optional but recommended accessory to help pr
6. de and spread out the Canopy Hoop Poles attaching the Roof Velcro as you go Orient the Porch Hoop Pole so that the holes face upward and then feed the length of the pole through the three Porch Hoop Sleeves sewn on the Tent Slide the Porch Hoop Pole onto the Porch Poles engaging the third hole position Attach the Porch Hoop Velcro on each side of the Tent Remove the Rear Adjustable Spreader Poles now supporting the hoops to allow the tent to be set in the next step rRear Adjustable Roof Velcro Spreader Poles p n 101580 Porch Hoop Pole p n 101479 Porch Pole p n 101121 Porch Velcro cPorch Hoop Sleeve i Voyager Tent p n 101572 Use third hole position To set the tent grasp the tent material at the rear of the shelter and pull it downward Observe the porch area of the tent lifting accordingly as you pull When the U Channel Molding is correctly installed the Porch Hoop Pole will lightly touch the floor ice To achieve this condition start by finding the center of the Molding From behind the unit pull the midpoint of the Tent downward and fold the Tent material under the lip of the Base Then press the midpoint of the molding over the Tent material and Base lip Continue pressing outward in both directions until you have secured about twel
7. olong the life of the unit Tow the unit out to your favorite fishing spot NOTE continuous pulling behind a four wheeler or snowmobile may result in premature wear of the base We recommend the optional Wear Strips be mounted to the base of your Fish Trap Make sure your Ice Shelter is completely dried out before storing for long periods of time Store your I ce Shelter in a cool dry place Keep away from rodents See our accessory catalog or www clamcorp com for these items and more Safety Instructions Please fully understand and follow all safety instructions as outlined Failure to do so could result in severe injury or death Do not use open flame heaters in your ice shelter Injury or death may result from fire if tent fabric is exposed to open flame The tent is not fireproof but the fabric is treated with a fire retardant that meets CPAI 84 specifications Application of any foreign substance may render the flame retardant properties ineffective Ice Armor fabric will melt when contact is made with hot surfaces i e heaters Death from asphyxiation may result from use of oxygen depleting heaters Open all vents for fresh air ventilation Never leave shelter unattended when set up Due to the increase in traffic snowmobiles autos etc on area lakes ice fishing can be hazardous at night If you choose to fish at night or in poor visibility conditions be sure to take precautions with lights or reflectors to
8. ve inches of material to the base Having temporarily secured the tent to the base take a walk around the unit Readjust the Molding until you have verified the proper Porch Hoop Pole position and also that the Tent sides and corners are properly proportioned When satisfied continue applying the Molding around the shelter one direction from center and then the other pulling the material as you go so that surface is relatively wrinkle free and snug You may need to trim the Molding ends if they are not equal Install the Front Rear and Roof Spreader Poles as indicated Adjust the Front and Rear Spreader Poles to snug the fit of the tent If everything still looks good secure the Molding with the included 6 Phillips Screws Evenly space them about every ten to twelve inches and also put a screw in the center of both corners Since there aren t any predrilled holes it s advisable to use a powered driver for this operation Base Ledge 41 1 2 Roof 30 Roof Spreader Pole Spreader Pole Use License Holder p n 101124 p n 101130 in States Applicable gt DE pe Front Adjustable 5 lt gt p n 101167 Rear Adjustable Spreader Pole p n 101580 6 x 3 8 Phillips Screw U Channel Molding p n 101148 p n 101116 10 Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the outside edge of the Base lip
Download Pdf Manuals
Related Search