Citizen CH-432B User's Manual
Contents
1. MEASUREMENTS 1 Attaching of Arm Cuff and Posture Wind the arm cuff around the left upper arm tightly so that During Measurement bottom edge of the cuff is positioned about 1 2cm above the elbow joint e When you will wind the cuff please wind the cuff next to the skin of possible g LV If measurement is made by rolling the shirts or jacket up over the arm this will constrict the upper arm and lk prevent accurate measurement e Cuff tube should be placed on the inside of your arm as figure caer ous e Please make sure that the cuff is fastened tightly Note that uneven cuff winding will prevent proper measure ments Eng 6 Rest the elbow on a table so that the section of the upper arm is at the height of the heart Relax the lower arm across the table and remain still since movement artifacts may falsifv the measuring result Make measurements in either a seated or reclining posture with the palm turned upward Insert the air connector from the cuff into the tube socket at the mainframe until it is tightly connected 2 Carrving out the Measurement Press the POWER START switch SYSTOLIC mmHg DIASTOLIC mmHg PULSE min When the POWER START switch is pressed the last measured systolic blood pressure and diastolic blood pres sure are displayed for about 2 seconds SYSTOLIC mmHg DIASTOLIC mmHg PULSE min At the first measurement after battery replacement th2. Upper Arm Cuff Soft Cuff Arm Circumference Range 22 0 to 32 0cm Pressure 0 to 280 mmHg Measurement Range Pulse 40 to 180 Pulse min Accuracy Pressure 3 mmHg Pulse 5 of Reading Systolic blood pressure 3 Digits Pressure Diastolic blood pressure 3 Digits LCD Indication Pulse Pulse rate 3 Digits ___ Alternately Measuring v Marks Batterv Emptv BTA View Size 18 H x 61 W mm LOD Digit Size Pressure 14 H x 6 5 Wjmm Switch POWER START switch nflation Automatic Inflation bv Internal Pump Deflation Automatic Air release Valve Exhaust Electromagnetic Valve Rated Voltage 6 VDC Power Source 4 AA Size Batteries Power Consumption 4W Measuring Battery Life Manganese Batteries Approx 200 times Alkaline Batteries 160 mmHg 1 time day 22 C Approx 700 times Automatic Power Off Function Approx 3 min Memory Function 1 Memory Dimension 129 W x 121 5 D x 55 T mm Weight Approx 300g 7 l Temperature 10 to 40 C Operating Environment Humidity 30 to 85 RH Storage Environment Temperature 20 to 60 C Humidity 10 to 95 RH Specifications and designs may be changed without notice in the event of improvements being made Eng 12 CITIZEN is a registered trademark of Citizen Watch Co Japan CITIZEN GROUP Consumer Electronics Division e CBM Bldg 5F 5 68 10 Nakan
3. GUN AD INSTRUCTION MANUAL FOR DIGITAL BLOOD PRESSURE MONITOR MODEL CH 432B CLEANING METHOD OF CUFF After cleaning the cuff with a neutral detergent lightly rinse it with water and let it dry in the air Hard rubbing or wash ing in a washing machine will cause air leakage Also be careful not to get water into the air hose GENERAL REMARKS General Remarks on blood pressure measurement If the cuff is to be deflated quickly depress POWER switch The attached cuff is suited for an arm circumstance of 22cm to 82cm When attaching the cuff rubber cuff hose should be placed on the inside of your arm on top of the arterial Self measurement is no therapy In no case may you change the dosage of medication prescribed by your phy sician In operation for blood pressure measurement you should urinate and should remain relatively still for 10 to 15 min utes prior to measurement Exercise eating and drinking smoking etc prior to mea surement may affect the results The blood pressure varies constantly throughout the day Mea surement should be made regularly at the same time each day Do NOT be impressed by the results of one measurement Keep a record of blood pressure variations Many read ings tell a story Emotional stress may tend to cause pressure to rise e This Product should not be used to monitor cardiac ar rhythmia mmHg o ee ol NORMAL 130 139 mmHg Systolic Blood Pr
4. e mark of W is displayed for about 2 seconds Eng 7 SYSTOLIC mmHg DIASTOLIC mmHg PULSE min SYSTOLIC mmHg DIASTOLIC mmHg PULSE min SYSTOLIC mmHg DIASTOLIC mmHg PULSE min The pressure is automatically heightened to the level for measurement of the blood pressure based on the last mea sured systolic blood pressure At the first measurement after battery replacement the pres sure is heightened to 160mmHg If the level of the pressure is not enough the pressure is automatically heightened to the level for measurement of the blood pressure again When the POWER START switch pressing the pressure level for measurement will change at optional level over 160 mmHg But if the POWER START switch is released before 160 mmHg the pressure is heightened to 160mmHg SYSTOLIC mmHg DIASTOLIC mmHg PULSE min When the pressure lowers by 15mmHg after pressuriza tion stops the mark of is displayed SYSTOLIC mmHg DIASTOLIC mmHg PULSE min If pulse is recognized the pressure is shifted to the dias tolic blood pressure indicating section and change over synchronized with the pulse Eng 8 SYSTOLIC mmHg DIASTOLIC mmHg t PULSE min SYSTOLIC mmHg DIASTOLIC mmHg PULSE min When the measurement has been completed the systolic blood pressure the diastolic blood pressure and the pulse rate are alternately displayed and the air is discharged The systolic blood pressure and t
5. essure Diastolic Blood Pressure For proper measurement of blood pressure e Take a deep breath five or six time and then relax before measuring blood pressure If you are tense when taking the measurement you will not get a valid reading e Blood pressure will be elevated when you are in a worri some or irritated state suffering from lack of sleep or constipation or after exercise or a meal Eng 2 Putting on the cuff is one of the most important tasks for ensuring proper measurement of blood pressure Wind the cuff around the arm and tighten it so that one finger mav be inserted between the cuff and arm Do NOT measure blood pressure after bathing or drink ing When vou feel like relieving vourself vou should do so before measuring blood pressure Measure blood pressure where the room temperature is about 20 C Do NOT measure blood pressure when it is too cold below 10 C or too hot above 40 C in theroom e Do NOT measure blood pressure immediately after drink ing coffee or tea or smoking e Measure blood pressure with a relaxed and quiet pos ture Keep the center of the cuff at the level of your heart and do NOT move your arm or talk during measurement e Do NOT keep on measuring so many times as your arm will have built up congestion of blood and you will not get a valid reading PRECAUTION FOR USE AND MAINTENANCE Precautions for use If you suffer from heart disease high blood pressure or other c
6. etting is about 40 mmHg higher than your usual maximum blood pressure 3 When the pressure display reaches the optimal pres sure value release the POWER START switch When the POWER START switch is released pressuriza tion will finish and measurement will start Manual pres sure settings can be selected between 160 mmHg 280 mmHg If you release the POWER START switch before reaching 160 mmHg the unit will pressurize to 160 mmHg If the unit senses that the pressure is not high enough it will apply more pressure Eng 9 3 Turn Power OFF Press the POWER START switch to turn off 4 Subsequent Measurement When a measurement is need again 10 minutes interval is necessarv between measurements 5 Automatic Power OFF Function If the unit is left without anv operation after measure ment an Automatic Power OFF Function runs to turn off the power after approximatelv 3 minutes To continue measurement press the POWER START switch again 6 Batterv Replacement If the batteries are almost empty the BTI mark will be displaved In this case batteries should be replaced with new one Batterv cover Remove the batterv cover at mainframe and replace four ype AA batteries BT Batteries are almost empty Batteries are normal Note The memory data are erased when you replace the batteries The batteries that are included power the monitor The
7. he diastolic blood pres sure are displayed for about 2 seconds and the pulse is displayed for about 1 second The measured data are registered automatically as long as they are not error When a person with maximum blood pressure of 170 mmHg or higher uses the unit for the first time or after changing batteries measure blood pressure using the manual set ting If the automatic pressure setting is used it may not work Automatic Pressure Setting This product automatically sets the pressure based on the previous measurement so you can easily measure blood pressure by pressing one button without reset ting the pressure for each measurement If several people use the unit we recommend using the manual settings as follows Manual Pressure Setting When several people use the unit set the pressure value manually Please note that if the manual pressure set ting is not used pressure will be automatically applied based on the value set by the previous user If the previous user had a high pressure setting that high pressure will automatically be used for the current user If you feel pain in your arm press the POWER START switch immediately to turn of the power 1 Put the arm cuff around your arm plug the air hose into the unit and keep your arm at the level of your heart 2 Keep the POWER START switch depressed until the pressure display shows the optimal pressure set ting The optimal pressure s
8. irculatory disease please consult your doctor first If you feel abnormal pressure of the cuff during use or any other irregularity reduce the pressure by immedi ately switching off the power or removing the batteries and consult the sales outlet where purchased If you think the measured value is abnormal or if measur ing makes you feel unwell discontinue use and consult your doctor Measurement of blood pressure may not be possible for someone with a weak pulse or arrhythmia Congestion swelling etc may occur in some people If blood pressure is measured repeatedly an accurate re sult will not be achieved An interval of about 10 minutes should be allowed e The memory is erased if the batteries are removed for replacement etc and a record should be kept of any nec essary data Precautions for maintenance Do NOT store the blood pressure monitor where it will be exposed to direct sunlight high temperature over 60 C low temperature below 20 C high relative humidity over 95 or in a dusty place Do NOT expose the blood pressure monitor to under force or vibration or drop it Remove the battery batteries when not in use for along pe riod Do NOT disassemble the apparatus Do NOT bend the cuff or air hose unnecessarily NEVER wipe the blood pressure monitor with thinner or benzene as they may damage it Eng 3 When the monitor is verv dirtv wipe it clean with a cloth moistened with Sterilizing a
9. lcohol or a neutral detergent and then wipe it with a dry cloth Do NOT use thinner or benzene Nature and frequency of maintenance This products is designed for use over an extended period of time however it is generally recommended that it be inspected every two years to ensure proper function and performance Protect the nature environment Please help protect natural environment by respecting na tional and or local recycling regulations when disposing of the batteries and the products at the end of their useful lives Reference European standard This products complies with EC instructions 93 42 EEC Medical Device Directive and with the following standards EN 1060 1 1995 Noninvasive Sphygmomanometers Part 1 General Requirements and EN 1060 3 1997 Noninvasive Sphygmo manometers Part 3 Supplemen tary Requirements for Electromechanical Blood Pressure Measuring Systems Manufacturer Name Premier Precision Ltd Address Block E G H 6th floor Phase 2 Yip Fat Factory Building 73 75 Hoi Yuen Road Kwun Tong Kowloon Hong Kong European Representative Name WvW elektronische Ger te Vertrieb GmbH Address Robert Koch Stra e 20 D 80538 M nchen GERMANY CE 0086 Eng 4 IDENTIFICATION OF PARTS Svstolic blood pressure Tube socket display section Diastolic blood pressure Pulse display section Cuff tube Air connector Cuff Power Start switch Eng 5
10. o Nakano ku Tokyo 164 0001 Japan Japan CBM Corporation Phone 03 5345 7430 Fax 03 5345 7431 E mail info con jcbm co jp
11. y may not last as long as indicated If manganese batteries are used at a low room tempera ture such as in the winter or for other reasons the bat teries may not function properly and you may not be able to measure your blood pressure Please dispose of used batteries properly to protect the environmental Eng 10 DESCRIPTION OF DISPLAV MARKS DISPLAV MARK CONDITION CAUSE CORRECTIVE ACTION SYSTOLIC mmHg DIASTOLIC mmHg Err jl PULSE min SYSTOLIC mmHg Err 5 PULSE min DIASTOLIC mmHg Displayed when the blood pressure could not be measured accurately Some noises were detected by the movement of arm during measurement Take off the cuff and wind it again and carry out measurement once more Do not move the arm during measure ment SYSTOLIC mmHg DIASTOLIC mmHg Err PULSE min PLL Displayed when the pulse rate could not be measured Take off the cuff and wind it again and carry out measurement once more Do not move the arm during measure ment SYSTOLIC mmHg DIASTOLIC mmHg PULSE min Displayed when the batteries are almost empty Replace four batteries SYSTOLIC mmHg DIASTOLIC mmHg PULSE min The unit has a trouble Eng 11 Take it to the store where it was purchased for testing SPECIFICATIONS Model No CH 432B Measuring Principle Oscillometric Method Measurement Localization Left
Download Pdf Manuals
Related Search