Cisco Systems N55M4Q User's Manual
Contents
1. Figure 2 13 Wall Mounting with a Magnet 209025 gt Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 After you mount the switch see the After Installing the Switch section on page 2 31 for information about configuring the switch Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 7 Chapter2 Switch Installation W Mounting the Switch In a Rack Installing the switch in a rack requires an optional bracket kit that is not included with the switch You can order these kits from your Cisco representative e 19 inch rack mounting brackets RCKMNT 19 CMPCT e 23 and 24 inch rack mounting brackets RCKMNT 23 CMPCT gt Warning To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety e This unit should be mounted at the bottom of the rack if it is the only unit in the rack e When mounting this unit in a partially filled rack load the rack from the bottom to the top with the heaviest component at the bottom of the rack e Ifthe rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack Statement 1006 To install the switch in a rack follow the instructions de2. Warning gt Warning gt Warning gt Warning W Preparing for Installation Read the wall mounting instructions carefully before beginning installation Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system Statement 378 Do not work on the system or connect or disconnect cables during periods of lightning activity statement 1001 Read the installation instructions before connecting the system to the power source Statement 1004 This product relies on the building s installation for short circuit overcurrent protection Ensure that the protective device is rated not greater than 20 A Statement 1005 To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety e This unit should be mounted at the bottom of the rack if it is the only unit in the rack e When mounting this unit in a partially filled rack load the rack from the bottom to the top with the heaviest component at the bottom of the rack e Ifthe rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack Statement 1006 Class 1 laser product Statement 1008 This equipment must be grounded Never defeat the ground con
3. CHAPTER Switch Installation This chapter describes how to start your switch and how to interpret the power on self test POST that ensures proper operation It also describes how to install the switch Read the topics and perform the procedures in this order e Preparing for Installation page 2 1 e Verifying Switch Operation page 2 5 e Mounting the Switch page 2 5 e Installing a Cover for the Reset Button Optional page 2 24 e Installing the Power Cord Retainer Optional page 2 25 e Installing the Cable Guard Optional page 2 28 e Connecting Devices to the Ethernet Ports page 2 33 Preparing for Installation e Warnings page 2 1 e Installation Guidelines page 2 3 e Equipment That You Supply page 2 4 e Box Contents page 2 4 e Powering the Switch page 2 4 Warnings These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Catalyst 3560 C and the 2960 C Switches guide A Warning Before working on equipment that is connected to power lines remove jewelry including rings necklaces and watches Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals Statement 43 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 Chapter2 Switch Installation gt Warning gt Warning gt Warning gt Warning gt
4. Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 19 Chapter2 Switch Installation W Mounting the Switch On a DIN Rail The DIN mount kit part number CMP DIN MNT gt is optional You can order it when you order your switch or you can order it later from your Cisco representative The DIN mount kit contains e Two number 10 Phillips pan head screws e DIN rail mount To install the switch on a DIN rail follow the instructions described in these sections e Attaching the DIN Mount Tray to the Switch page 2 20 e Mounting the Switch on a DIN Rail page 2 21 e Removing the Switch from a DIN Rail page 2 23 Attaching the DIN Mount Tray to the Switch Step1 Place the switch on the DIN rail mount See Figure 2 17 Figure 2 17 Placing the Switch on the DIN Mount Tray 344212 i Sich IN a Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 20 OL 23803 02 Chapter2 Switch Installation Mounting the Switch E Step2 Use the two number 10 Phillips pan head screws to secure the DIN rail mount to the switch See Figure 2 18 Figure 2 18 Securing the DIN Mount Tray to the Switch 344213 2 Number 10 Phillips pan head screws Mounting the Switch on a DIN Rail A Caution Do not install the switch with its front panel facing up Following safety regulations install the switch with its front panel facing down to allow sufficient airflow and to provide easier ac
5. e Connect a 10 100 1000 uplink port to a PoE or PoE switch such as a Catalyst 3750 X Or e Plug the auxiliary power adapter cord into the switch AUX power connector and into an AC power outlet Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 im OL 23803 02 Chapter2 Switch Installation Verifying Switch Operation W amp Note You can use both the uplink port and the auxiliary power adapter However the auxiliary power input takes precedence Catalyst 3560CPD 8PT S e Connect a 10 100 1000 uplink port to a PoE switch such as a Catalyst 3750 X Or e Plug the auxiliary power adapter cord into the switch AUX power connector and into an AC power outlet amp Note You can use both the uplink port and the auxiliary power adapter However the auxiliary power input takes precedence All models except the Catalyst 2960CPD 8PT L 2960CPD 8TT L and 3560CPD 8PT S e Plug the AC power cord to the switch AC power connector and into an AC power outlet Verifying Switch Operation As the switch powers on it begins the POST a series of tests that runs automatically to ensure that the switch functions properly LEDs blink during the test which lasts approximately 1 minute When the switch begins POST the System Status Duplex and Speed LEDs turn green The System LED blinks green and the other LEDs remain green When the POST completes successfully the System LED turns green The other LEDs
6. 10 000 feet 3 049 meters e Do not place any items on the top of the switch e Do not wall mount the switch with its front panel facing up Following safety regulations wall mount the switch with its front panel facing down or to the side to prevent airflow restriction and to provide easier access to the cables e Clearance to the switch front and rear panels meets these conditions You can easily read the front panel LEDs Access to ports is sufficient for unrestricted cabling The AC power cord can reach from the AC power outlet to the connector on the switch rear panel e For 10 100 and 10 100 1000 fixed ports cable lengths from the switch to connected devices are not more than 328 feet 100 meters e For cable lengths for small form factor pluggable SFP module connections see the SFP Module Connectors section on page B 2 and the module documentation Equipment That You Supply You might need this equipment to install the switch e Number 2 Phillips screwdriver e Drill with a 27 drill bit 0 144 inch 3 7 mm Box Contents The switch getting started guide on Cisco com describes the box contents If any item is missing or damaged contact your Cisco representative or reseller for support Powering the Switch Before installing the switch in a rack on a desk a shelf or a wall you should power on the switch and verify that it passes POST Power the switch Catalyst 2960CPD 8PT L and 2960CPD 8TT L
7. a 0 144 in 3 7 mm or a 27 drill bit to drill three 1 2 in 12 7 mm holes in the desk See Figure 2 8 Insert the three number 8 Phillips pan head screws in the slots on the mounting tray and tighten them Figure 2 8 Attaching the Tray to the Desk or Shelf 208923 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 1 Em Chapter2 Switch Installation W Mounting the Switch 1 Number 8 Phillips pan head screws 3 Desk or shelf 2 Mounting tray Step4 Place the switch onto the mounting screws and slide the switch until it locks into place See Figure 2 9 Figure 2 9 Installing the Switch on the Mounting Tray 282396 1 Switch 3 Mounting tray 2 Sliding direction 4 iDesk Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 4 a OL 23803 02 Chapter2 Switch Installation Mounting the Switch E Step5 Use the two number 10 Phillips pan head screws to secure the mounting tray to the switch See Figure 2 10 Figure 2 10 Securing the Mounting Tray to the Switch 282397 Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Mounting Tray with a Magnet You can use a magnet with the mounting tray to mount the switch e Ona metal surface e Under a metal surface e Ona metal wall A Caution Do not use the magnet without a mounting tray This example
8. turn off and then reflect the switch operating status If a switch fails POST the System LED turns amber POST failures are usually fatal Call Cisco technical support representative if your switch fails POST After a successful POST unplug the power cord from the switch Mount the switch in a rack on a desk or shelf under a desk or shelf or on a wall as described in the Mounting the Switch section on page 2 5 Mounting the Switch e Ona Desk or Shelf without Mounting Screws e Desk Shelf or Wall with Mounting Screws e With a Mounting Tray e Ina Rack e Ona DIN Rail Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 5 Chapter2 Switch Installation W Mounting the Switch On a Desk or Shelf without Mounting Screws Step1 Locate the adhesive strip with the rubber feet in the accessory kit Step 2 Remove the four rubber feet from the adhesive strip and attach them to the recessed areas on the bottom of the unit This prevents the switch from sliding on the desk or shelf DA Note We strongly recommend that you attach the rubber feet Doing so helps prevent airflow restriction and overheating Step3 Place the switch on the desk or shelf A Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 After you mount the switch see the After Installing the Switch section on pa
9. 2 26 Slide the retainer around the AC power cord and pass it around the loop on the switch See Figure 2 23 Figure 2 23 Inserting the Retainer through the Lanced Loop 1 AC power cord 3 Sleeve for thinner power cords 2 Power cord retainer 4 Loop Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 25 Chapter 2 Switch Installation W installing the Power Cord Retainer Optional Step 3 Step 4 Step 5 Slide the retainer through the first latch See Figure 2 24 Figure 2 24 Sliding the Retainer Through the Latch 1 AC power cord 3 Latch 2 Smaller sleeve for thin power cords Slide the retainer through the other latches to lock it See Figure 2 25 Figure 2 25 Locking the Retainer 1 AC power cord 3 Latches 2 Sleeve for thin power cords Optional Use the small sleeve for thin power cords Use the small sleeve to provide greater stability for thin cords Detach the sleeve and slide it over the power cord See Figure 2 26 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 26 OL 23803 02 Chapter2 Switch Installation Installing the Power Cord Retainer Optional E Figure 2 26 Sleeve Around the Power Cord N o O o O N 1 Sleeve for thin power cords 2 AC power cord Step6 Secure the AC power cord by pressing on the retainer See Figure 2 27 Figure 2 27 Securing the Power Cord in the Retainer Cata
10. 246 1 Switch Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 23 Chapter2 Switch Installation W installing a Cover for the Reset Button Optional Installing a Cover for the Reset Button Optional You can cover the reset button to prevent accidental or unauthorized reset of your switch To install a cover on the reset button 1 Locate the cover in the accessory kit 2 Remove the adhesive sticker from the back of the cover 3 Apply the cover on the switch See Figure 2 21 and Figure 2 22 as examples You can apply the cover to other switch models as well Figure 2 21 Reset Cover on the Catalyst 2960CPD 8PT L Switch AUX SVE 1 5q 330756 Swick Reon ov Figure 2 22 Reset Cover on the Catalyst 2960CG 8PC S Switch Such O p on cove Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 2 a OL 23803 02 Chapter2 Switch Installation Installing the Power Cord Retainer Optional E Installing the Power Cord Retainer Optional N Note Step 1 Step 2 This section applies to switches with an AC power connector The power cord retainer part number PWR CLP is optional You can order it when you order your switch or you can order it later from your Cisco representative Choose the sleeve size of the power cord retainer based on the thickness of the cord The smaller sleeve can be snapped off and used for thin cords See Figure
11. 79 S Note Applies to the Catalyst 3560CG 8PC S switch Installation Guidelines Before installing the switch these guidelines must be met e The operating environment must be within the ranges listed in Appendix A Technical Specifications e Cabling is away from sources of electrical noise such as radios power lines and fluorescent lighting fixtures Make sure that the cabling is away from other devices that might damage the cables e Airflow around the switch and through the vents must be unrestricted We strongly recommend that you allow at least 3 in 7 6 cm of clearance from the left right and top sides of the switch to avoid any flow blockage If you are installing the switch in a rack allow at least 1 75 in 4 cm of empty rack space above each switch e Catalyst 3560CG 8PC S 2960C 8PC L 2960C 12PC L 3560C 8PC S and 3560C 12PC S switches Allow at least 1 75 in 4 cm clearance from the ends of the external heat sink fins Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 3 Chapter2 Switch Installation W Powering the Switch e Temperature around the unit does not exceed 113 F 45 C If the switch is installed in a closed environment or in a multirack assembly the temperature around it might be greater than normal room temperature e Humidity around the switch must not exceed 95 percent e Altitude at the installation site must not be greater than
12. E configuration The results show output current output power and heat dissipation A Warning Voltages that present a shock hazard may exist on Power over Ethernet PoE circuits if interconnections are made using uninsulated exposed metal contacts conductors or terminals Avoid using such interconnection methods unless the exposed metal parts are located within a Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 3 w OL 23803 02 Chapter2 Switch Installation Where to Go Next W restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard A restricted access area can be accessed only through the use of a special tool lock and key or other means of security Statement 1072 gt Caution Category 5e and Category 6 cables can store high levels of static electricity Always ground the cables to a suitable and safe earth ground before connecting them to the switch or other devices Where to Go Next To change the switch settings you can use the switch default configuration or use any of the management options described in the Management Options section Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 35 Chapter2 Switch Installation W Where to Go Next Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 36 OL 23803 02
13. Figure 2 30 Pivoting the Cable Guard Upwards 1 iCable guard 2 Pivot direction for cable guard pivots Attach the cables to the switch See Figure 2 31 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 29 Switch Installation Chapter 2 Attaching the Cables to the Switch OvOOEE 816800 A a TY A a HH ee Moe eee cee HII e ee ee ee HMMM ore ee eee TO HO EEEECEEE EEE HELE COTE COTE VOTE EET TE COTE OU COTE HOE 2 Pivot direction for cable guard pivots 33 Tighten the screws Guiding the Cables through the Guard OL 23803 02 Installing the Cable Guard Optional Figure 2 31 2 N gt z 3 BD 29 oO as Q fo I z N QO Q 3 lt UN U Guide the connected cables through the slots in the front of the cable guard Slide the cable guide in as Step 4 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide Chapter2 Switch Installation After Installing the Switch Hi Step5 Optional To attach the cable guard to the desk or wall use a 0 144 inch 3 7 mm or a 27 drill bit to drill 1 2 inch 12 7 mm holes at each of the two mounting locations Insert the supplied 0 5 in 12 7 mm number 8 Phillips wood screws and tighten them as shown in Figure 2 33 Figure 2 33 Securing the Cable Guard to the Desk 1 Number 8 Phillips wood screws 2 Desk or shelf After Installing the Switch 1 P
14. cess to the cables A Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Step1 Position the switch directly in front of the DIN rail making sure that the top of the DIN rail mount clip hooks over the top of the DIN rail See Figure 2 19 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 27 W Chapter2 Switch Installation W Mounting the Switch Figure 2 19 Mounting the Switch on a DIN Rail ID o M 344214 1 Switch Step2 Rotate the switch down toward the DIN rail until the release tabs on the DIN rail mount clicks Step3 Lift lightly on the bottom of the switch to ensure that it is firmly locked in place After you install the switch see the After Installing the Switch section on page 2 31 for information about the switch configuration Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 22 OL 23803 02 Chapter2 Switch Installation Mounting the Switch I Removing the Switch from a DIN Rail Step 1 Ensure that power is removed from the switch and disconnect all cables and connectors from the front panel of the switch Step 2 Pull down on the DIN rail mount release tabs As the clips release lift the bottom of the switch See Figure 2 20 Figure 2 20 Switch Removal 344
15. ductor or operate the equipment in the absence of a suitably installed ground conductor Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available Statement 1024 Ultimate disposal of this product should be handled according to all national laws and regulations Statement 1040 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 2 OL 23803 02 Chapter 2 Switch Installation gt Warning gt Warning gt Preparing for Installation E For connections outside the building where the equipment is installed the following ports must be connected through an approved network termination unit with integral circuit protection 10 100 1000 Ethernet Statement 1044 To prevent the system from overheating do not operate it in an area that exceeds the maximum recommended ambient temperature of 113 F 45 C Statement 1047 S Note For Catalyst 3560CG 8PC S 3560CG 8TC S and 2960CG 8TC L switches the maximum recommended ambient temperature is 104 F 40 C No user serviceable parts inside Do not open Statement 1073 Installation of the equipment must comply with local and national electrical codes Statement 1074 To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Hot surface Statement 10
16. e 4 Adhesive Step4 Use a 0 144 inch 3 7 mm or a 27 drill bit to drill a 1 2 inch 12 7 mm hole in the three screw template slots Step5 Insert three screws in the slots on the screw template and tighten until they touch the top of the screw template Step6 Remove the screw template from underneath the desk or shelf Step7 Place the switch upside down onto the mounting screws and slide it forward until it locks in place See Figure 2 4 Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 9 Chapter2 Switch Installation W Mounting the Switch Wall Mounting A Warning A Caution Figure 2 4 Mounting the Switch Under a Desk or Shelf 282395 1 Desk or shelf 3 Slides on this way 2 Screws After you mount the switch see the After Installing the Switch section on page 2 31 for information about configuring the switch Read the wall mounting instructions carefully before beginning installation Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system Statement 378 Do not wall mount the switch with its front panel facing up Following safety regulations wall mount the switch with its front panel facing down or to the side to
17. g a Bale Clasp Latch SFP Module 208914 1 Bale clasp Connecting Devices to the Ethernet Ports e Connecting to the 10 100 and 10 100 1000 Ports page 2 33 e Connecting to the PoE Ports page 2 34 Connecting to the 10 100 and 10 100 1000 Ports The 10 100 and 10 100 1000 Ethernet ports use RJ 45 connectors with Ethernet pinouts The maximum cable length is 328 feet 100 meters The l1OOBASE TX and LOOOBASE T traffic requires Category 5 Category 5e or Category 6 UTP cable The 10BASE T traffic uses Category 3 or Category 4 cable The autonegotiation feature is enabled by default on the switch At this setting the switch ports configure themselves to operate at the speed of the attached device If the device does not support autonegotiation you can set the switch port speed and duplex parameters To maximize performance either let the ports autonegotiate both speed and duplex or set the port speed and duplex parameters on both ends of the connection See the switch software configuration guide or the switch command reference on Cisco com for more information about autonegotiation and auto MDIX If auto MDIX is disabled use the guidelines in Table 2 1 to select the cable for connecting the 10 100 1000 Ethernet ports to other devices See the Cables and Adapters section on page B 3 for cable pinout descriptions See Figure 2 36 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 33 Chapter2 Sw
18. ge 2 31 for information about the switch configuration Desk Shelf or Wall with Mounting Screws You can use the mounting screws to mount the switch e Ona desk or a shelf e Under a desk or a shelf e Ona wall Desk or Shelf Mounting Step1 Use the screw template to align the mounting screw holes and also as a guide to make sure that you install the screws into the desk or shelf with proper clearance Step2 Position the screw template on top of the desk or shelf so that the two side by side slots face the front of the desk or shelf as shown in Figure 2 1 This ensures that the power cord faces the rear of the desk or shelf after the switch is installed D Note Wait before you attach the screw template to the desk or shelf Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 6 OL 23803 02 Chapter2 Switch Installation Mounting the Switch Hi Figure 2 1 Installing the Mounting Screws on Top of a Desk or a Shelf Step3 Peel the adhesive strip off the bottom of the screw template and attach it to the top of the desk or shelf Step4 Use a 0 144 inch 3 7 mm or a 27 drill bit to drill a 1 2 inch 12 7 mm hole in the three screw template slots Step5 Insert three screws in the slots on the screw template and tighten them until they touch the top of the screw template Step6 Remove the screw template from the desk or shelf Step7 Place the switch onto the mounting screws and slide it forward u
19. h Installation W Mounting the Switch Figure 2 6 Installing the Mounting Screws on the Wall or Figure 2 7 Installing the Switch on a Wall _e nS en 3 Step8 Place the switch onto the mounting screws and slide it down until it locks in place See Figure 2 7 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 2 OL 23803 02 Chapter2 Switch Installation Mounting the Switch E With a Mounting Tray The mounting kit part number CMP MGNT TRAY is optional You can order it when you order your switch or you can order it later from your Cisco representative The mounting kit ships contents e Two number 10 Phillips pan head screws e Three number 8 Phillips pan head screws e Mounting tray e Magnet You can use the mounting tray by itself with mounting screws or with a magnet Mounting Tray with Screws A Caution Step 1 Step 2 Step 3 You can use the mounting tray to secure the switch e On a desk or shelf e Under a desk or shelf e Onawall Do not wall mount the switch with its front panel facing up Following safety regulations wall mount the switch with its front panel facing down or to the side to allow sufficient airflow and to provide easier access to the cables This example shows you how to mount the switch on a desk or shelf You can use a similar procedure to mount the switch under a desk or on a wall Place the mounting tray on the desk Use
20. itch Installation W Connecting Devices to the Ethernet Ports Figure 2 36 Connecting to an Ethernet Port y Catalyst 2 y 960 Series Pp SF y 208915 Table 2 1 Ethernet Cables Auto MDIX Disabled Device Crossover Cable Straight Through Cable _ Switch to switch Yes No Switch to hub Yes No Switch to computer or server No Yes Switch to router No Yes Switch to IP phone No Yes 1 IOOBASE TX and 1000BASE T traffic requires twisted four pair Category 5 Category 5e or Category 6 cable I OBASE T traffic uses Category 3 or Category 4 cable Connecting to the PoE Ports The 10 100 PoE ports have the same autonegotiation settings and cabling requirements as those in the Connecting to the 10 100 and 10 100 1000 Ports section on page 2 33 These ports provide PoE power See the e PoE Ports Switches with PoE Ports section on page 1 5 for information on the cables and connectors The ports provide PoE support for 802 3af compliant devices and also provide Cisco prestandard PoE support for Cisco IP Phones and Cisco Aironet Access Points On a per port basis you can control whether or not a port automatically provides power to a connected IP phone or an access point To access an advanced PoE planning tool use the Cisco Power Calculator on Cisco com http tools cisco com 20 launch jsp You can use this application to calculate the power supply requirements for a specific Po
21. lyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 27 Chapter2 Switch Installation W installing the Cable Guard Optional Installing the Cable Guard Optional The cable guard prevents tampering with the cables after the cables are installed The cable guard CMP CBLE GRD is not included with the switch but you can order it from your Cisco representative Note You can use the cable guard when the switch is mounted on a desk under a desk or on a wall The cable guard is shipped with these items e Two 0 5 in 12 7 mm number 8 Phillips wood screws e Two number 10 Phillips pan head screws e Two washers Step 1 Optional Attach the supplied washers before you install the cable guard See Figure 2 28 N Note This is only required if you are not installing the wall mount brackets Figure 2 28 Using the Washer 1 Washer Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 28 OL 23803 02 Chapter2 Switch Installation Installing the Cable Guard Optional E Step2 Use the supplied number 10 pan head screws to attach the cable guard to the switch See Figure 2 29 Figure 2 29 Attaching the Cable Guard to the Switch 1 Switch 3 Two number 10 Phillips pan head screws 2 Cable guard Step3 Loosen the number 10 Phillips pan head screws slide the cable guide out and pivot it upwards so that you can install the cables See Figure 2 30
22. move it to the open unlocked position Align the module in front of the slot opening and push until you feel the connector snap into place If the module has a bale clasp latch close it For fiber optic SFP modules remove the dust plugs and save Connect the SFP cables Figure 2 34 Installing an SFP Module 208913 Do not remove the dust plugs from the fiber optic SFP module port or the rubber caps from the fiber optic cable until you are ready to connect the cable The plugs and caps protect the SFP module ports and cables from contamination and ambient light Removing SFP Modules Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Attach an ESD preventive wrist strap to your wrist and to a bare metal surface Disconnect the cable from the SFP module For reattachment note which cable connector plug is send TX and which is receive RX Insert a dust plug into the optical ports of the SFP module If the module has a bale clasp latch pull the bale out and down to eject it If the latch is obstructed and you cannot use your finger use a small flat blade screwdriver or other long narrow instrument Grasp the SFP module and carefully remove it from the slot Place the module in an antistatic bag or other protective environment Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 32 OL 23803 02 Chapter2 Switch Installation Connecting Devices to the Ethernet Ports Hi Figure 2 35 Removin
23. ntil it locks in place See Figure 2 2 iN Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 7 Chapter2 Switch Installation W Mounting the Switch Figure 2 2 Mounting the Switch on Top of a Desk or Shelf 1 Slides on this way 3 Desk or shelf 2 Screws After you mount the switch see the After Installing the Switch section on page 2 31 for information about configuring the switch Under the Desk or Shelf Mounting Step1 Use the screw template to align the mounting screw holes and also as a guide to make sure the screws are installed under the desk or shelf with proper clearance Step2 Position the screw template underneath the desk or shelf so that the two side by side slots face the front of the desk or shelf as shown in Figure 2 3 This ensures that the power cord faces the rear of the desk or shelf after the switch is mounted Step3 Peel the adhesive strip off the bottom of the screw template and attach it to the underside of the desk or shelf Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 8 OL 23803 02 Chapter2 Switch Installation Mounting the Switch E Figure 2 3 Installing the Mounting Screws Under a Desk or Shelf Si Oh 9i 250146 1 Desk or shelf 3 Screws 2 Screw templat
24. ower on the switch See the Verifying Switch Operation section on page 2 5 2 Connect to a 10 100 or 10 100 1000 port and run Express Setup See the switch getting started guide for instructions 3 Connect to the ports See the Connecting Devices to the Ethernet Ports section on page 2 33 to complete the installation For configuration instructions about using the CLI setup program go to Appendix C Configuring the Switch with the CLI Setup Program Installing SFP Modules When installing SFP modules observe these guidelines e Removing and installing an SFP module can shorten its useful life Do not remove and insert any module more often than is absolutely necessary e To prevent ESD damage follow your normal board and component handling procedures when connecting cables to the switch and other devices Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 37 Wi Chapter2 Switch Installation HE Removing SFP Modules A Warning Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 gt Caution Class 1 laser product Statement 1008 Attach an ESD preventive wrist strap to your wrist and to a bare metal surface Find the send TX and receive RX markings on the module top On some SFP modules the TX and RX markings might be replaced by arrows that show the direction of the connection either send or receive If the module has a bale clasp latch
25. prevent airflow restriction and to provide easier access to the cables Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 0 OL 23803 02 Chapter2 Switch Installation Mounting the Switch I Step1 Locate the screw template The template is used to align the mounting screw holes S Note Figure 2 5 shows the measurements for the location of the screws on the switch Step2 Position the screw template so that the two side by side slots face toward the floor as shown in Figure 2 6 For the best support of the switch and cables make sure that you attach the switch securely to a wall stud or to a firmly attached plywood mounting backboard Step3 Peel the adhesive strip off the bottom of the screw template Step4 Attach the screw template to the wall Step5 Use a 0 144 inch 3 7 mm or a 27 drill bit to drill a 1 2 inch 12 7 mm hole in the three screw template slots Step6 Insert three screws in the slots on the screw template and tighten until they touch the top of the screw template Step7 Remove the screw template from the wall Figure 2 5 Location of the Mounting Holes on the Switch eeeeeeeeeeeeeeeeee t tlt Ir CISCO 4 2 330380 1 11 77 in 4 49 cm 4 2 67 in 6 78 2 3 72 in 9 44 cm 5 2 46 in 6 24 3 62 in 9 19 cm 6 Switch Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 1 Wi Chapter2 Switc
26. scribed in these sections e Attaching Brackets to the Switch page 2 18 e Mounting the Switch in a Rack page 2 19 Attaching Brackets to the Switch Figure 2 14 shows how to attach a 19 inch bracket to one side of the switch Follow the same steps to attach the second bracket to the opposite side Figure 2 14 Attaching the 19 inch Brackets for Rack Mounting 282399 1 Phillips flat head screw Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 8 OL 23803 02 Chapter2 Switch Installation Mounting the Switch E Figure 2 15 shows how to attach a 23 inch bracket to one side of the switch Follow the same steps to attach the second bracket to the opposite side Figure 2 15 Attaching the 23 inch Brackets for Rack Mounting 282400 1 Phillips flat head screw Mounting the Switch in a Rack After the brackets are attached to the switch insert the switch into the rack and align the bracket in the rack Use either the number 12 or number 10 Phillips machine screws to secure the switch in the rack See Figure 2 16 A Warning To prevent airflow restriction allow clearance around the ventilation openings to be at least 3 in 7 6 cm Statement 1076 Figure 2 16 Mounting the Switch in a Rack 282402 1 Phillips machine screws After you mount the switch see the After Installing the Switch section on page 2 31 for information about the switch configuration
27. shows you how to mount the switch on a metal wall You can use a similar procedure to mount the switch under a metal desk or on a metal desk Catalyst 3560 C and 2960 C Switch Hardware Installation Guide OL 23803 02 2 5 Chapter2 Switch Installation W Mounting the Switch Step1 Place the switch on the mounting tray See Figure 2 11 Figure 2 11 Placing the Switch on the Mounting Tray 282398 Sich Mourn Step2 Use the two number 10 Phillips pan head screws to secure the mounting tray to the switch See Figure 2 12 Figure 2 12 Securing the Mounting Tray to the Switch 282397 2 Number 10 Phillips pan head screws Step3 Place one side of the magnet against the bottom of the mounting tray as shown in Figure 2 13 Mount the magnet and switch on a metal wall Catalyst 3560 C and 2960 C Switch Hardware Installation Guide 2 4 6 OL 23803 02 Chapter2 Switch Installation Mounting the Switch E gt Warning Read the wall mounting instructions carefully before beginning installation Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system Statement 378 gt Caution Do not wall mount the switch with its front panel facing up Following safety regulations wall mount the switch with its front panel facing down or to the side to allow sufficient airflow and to provide easier access to the cables
Download Pdf Manuals
Related Search