Cisco Systems CF2001P User's Manual
Contents
1. Standard width of the margin a 3 0 mm 1 0 mm with Fiery X3e installed 5 0 mm 1 0 mm with MicroPress PrintLink 2020m installed If the width of the measured margin does not meet its standard width follow the procedure in the next section Adjusting the Paper Ref erence Position for PF 118 to adjust it C4004P588CA 5 Click Left Margin C4658U028AA C4658P003CA 6 Select the key for the paper drawer that is to be adjusted and then click the Start key in the External Panel Controller ETET or A test page is printed ETET Left Margin a t 3 0mm _ Extent BER 3 88 s onm Letter D Normal C4658P005CA a a_a 4004 7715 01 _ 30 E Adjusting the Paper Reference C4004P565CA C4004P597CA Machine Adjust C4658P003CA CF2001P Position for PF 118 1 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual 2 Click Machine Adjust 3 Click PRT Area 4 Click Left Margin 5 Select the paper drawer that you wish to adjust and then click the up and down arrows in the lower right corner of the screen to enter the2. 6 Fully pull the toner hopper shutter out toward you Pulling out the toner hopper shutter allows the toner to begin filling the toner hop per Check that all of the toner has emptied out of the toner bottle and into the hopper which may take a while C4004U066AA NOTE Do not tap on the toner bottle while refilling the hopper otherwise the toner may spurt out 7 Push the toner hopper shutter closed until it snaps into place and closes the bottle C4004U067AA 8 Tilt the toner bottle slightly backward and then pull the opening of the bottle up and toward you to remove it 10 Fill the magenta cyan and black toner in the same way as described in steps 2 through 9 NOTE Be sure to fill the toner hoppers with the cor rect color of toner 11 After all four toner hoppers are filled grasp the toner supply door as shown and then carefully swing the door down to close it 4004 7715 01 NEXT Affix the support label on the right side of the top of the toner supply door CF2001P 4 Connecting the Cables 5 Affixing the Support Label 1 Make sure that the printer power cord is not Support label plugged into the electrical outlet and then insert the plug on the end of the power cord NOTE into the power cord connector on the printer Affix the label that corresponds with the installed options C4004U589AA 2 Insert the plug on the other end of the power cord into an electrical
3. Tel Ray 2 edge patches 2 canter patches lt Guide 20 gt C4004P590CA gt gt Read the pattern of Yellow Read the pattern of Black 2 edge patches lt GudetO 2 center patches Guide 30 Jf C4004P591CA CF2001P 21 Check that Read the Pattern of Cyan dis appears and that gt gt appears beside Read the Pattern of Magenta NOTE If the cyan test pattern is read correctly Read the Pattern of Cyan disappears from the dialog box 22 Prepare the magenta test pattern and then repeat steps 13 through 21 of the above pro cedure to read the magenta test pattern with the X Rite NOTE If the magenta test pattern is read correctly Read the Pattern of Magenta disappears from the dialog box 23 Prepare the yellow test pattern and then repeat steps 13 through 21 of the above pro cedure to read the yellow test pattern with the X Rite NOTE If the yellow test pattern is read correctly Read the Pattern of Yellow disappears from the dialog box gt gt Read the pattern of Black 2 edge patches lt Gude1O 2 canter patches lt Gude 30 gt J Concel J C4004P592CA Rite Calitvation Test Patter Read Mode Reading has been completed correctly Switch the selector to the main part and press the OK button C4004P595CA A_ B _ gt C4004U593AA Tech Rep Mode 24 Prepare the black test pattern and then
4. 2 0 0 1 0 4 0 1 1 S 3 0 Present Date Time 20 1 1 of oF Year Month Date Hour Minute C4004PU08CA 4004 7715 01 99 CF2001P E Specifying the Serial Number 4 Make sure that Printer is selected Using the keypad in the External Panel Controller enter the printer s serial number Repeat this step to enter the serial numbers for LCC Sorter FN and Duplex NOTE Be sure to specify the serial number When the serial number is specified the settings for each unit can be read by the printer If the serial number is not specified a correctly adjusted image cannot be printed C4004P585CA di 1 Check that the External Panel Controller 5 Click END SSS appears in the computer screen and then E display the Tech Rep Mode screen For details about displaying the Tech Rep Mode T screen refer to the Service Manual 6 Click Menu and then click Fin Time C4004P565CA 2 Click System Input Tech Rep Mode C4004P597CA 3 Click Serial Input System Input Menu C4004P584CA 4004 7715 01 94 CF2001P E Specifying Who Performs Replacements NOTE The message that appears a unit must be replaced can be changed to indicate that either the user or the service representative must perform the replace ment Select the appropriate settings depending o
5. SETUP INSTRUCTIONS CF2001P Printer A WARNING e Do not plug in the power cord or turn on this unit until you are instructed to according to this manual A CAUTION e Install this machine so that it can quickly be unplugged from the electrical outlet in case of an emergency The socket outlet shall be installed near the machine and shall be easily accessible e Keep all packing materials out of the reach of children NOTE e If the CF2001P is connected to the Minolta MircroPress Cluster Printing System be sure to take back the User Manual for the CF2001P since it is not needed by the customer e Keep all packing materials in a safe place for later use in case they are needed for transportation 4004 7715 01 MINOLTA CO LTD Printed in Japan CF2001P NEXT 1 Outline of the CF2001P System Setup When setting up the system consisting of this unit and its options set up each unit in the o oo Order shown below NOTE e Install and setup each option according to the instructions included with the NOTE option Set up each unit correctly according to its SETUP INSTRUCTIONS For information on adjusting each option refer to the section 10 Adjusting the Options on page 29 1 A Copy Table CT 2 2 A Paper Feed Unit PF 118 aB se n Cabinet 2 C Copy Desk CD 2M 3 B Dehumidifying Heater PF 118 4 CF2001P Printer 5 Duplex Unit AD 14 3 A Dehumidifying Heater PF 117 7 Mechanical Counter 8 IF Kit 6 Dat
6. 1 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For 5 Using the keypad in the External Panel Con details about displaying the Tech Rep Mode screen refer to the Service Manual ero Ra sMAnuteS ofpnap use CUSE troller enter the desired number of minutes l and then click Enter 2 Click Utility NOTE Select the C Clear key to erase the entered number C4004P058CA 6 Click Exit Casaread Prune Carteotter 7 Click Exit sn 3 Click User s Choice 8 Check that the message displayed in the a control panel changes from Alert Printing suspended to Info 9 Exit the External Panel Controller User s ainis NOTE Before connecting or disconnecting the har nesses of the IR port cable be sure to turn off the printer and the converter C4004P599CA _ SSSESE SS SSS SSSSSSSSSSSSSSqqqQqQqQqQqQqQqQqQqqqJqQqqqQqQqQqQqQqQqQqQq__SSSSSSSSSSSSqqqQqQqQqQq _SSS sz 4004 7715 01 905 CF2001P O NEXT E To set the Sleep Mode parameter NOTE When making settings according to the customers requests refer to the procedure described below 1 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service M
7. repeat steps 13 through 21 of the above pro cedure to read the black test pattern with the X Rite 25 Check that the dialog box appears set the selector knob on the selector from B to A and then click OK in the dialog box NOTE Be sure to click OK only after the selector knob has been set 26 Check that the Tech Rep Mode screen is displayed 27 Click Fin Time E 19 4004 7715 01 O NEXT CF2001P 8 Making System Setting Factory Setting Mode Menu _ 3 Click END m Checking the Date Settin Date Time Input 1 Check that the External Panel Controller mal mE inate m axl appears in the computer screen and then a ale display the Date Time Input screen For Teor Toe or ae ae details about displaying the Date Time Input Year Month Date Hour Minute screen refer to the Service Manual C4004PU09CA C4004P565CA 4 Click Menu 5 Check that the Basic screen appears on the External Panel Controller Year Month Date Hour Minute Present Date Time 200 1 1 of o Year Month Date Hour Minute C4004PU07CA ao Sauce rol 2 Check that the current date and time settings ate Tine Inpu are correct If the settings are not correct use the keypad in the External Panel Con EMm EO m E E troller to enter the correct date and time in Year Honth Date Hour Minute the upper row of the screen Example To specify April 1 2001 15 30 click
8. 7 Click END twice C4656PO06CA Ce e O s 4004 7715 01 _ 38 CF2001P lt Maintenance Center Billing Center Settings gt NOTE The procedure for making Maintenance Center settings are described below If Billing Center settings are necessary specify them using the same procedure after entering the Maintenance Center settings lt Clearing the Maintenance RAM gt 1 Click Maintenance For the Billing Center click Billing ice C4656P003CA EEEn 2 Click ID Code so that it appears in white on a black background NOTE For the Billing Center there is no need to enter an ID code C4656P008CA 3 Using the keypad in the External Panel Controller enter the 7 digit ID code NOTE Enter the service representative s ID code C4656PO009CA C4656P011CA Click ID Code again so that it appears in black on a white background Click RAM Clear Click Yes Click END C E uuu 4004 7715 01 39 O NEXT CF2001P 6 Using the keypad in the External Panel Controller enter the 4 digit Center ID lt DT Settings gt 1 Click ID Code so that it appears in white on a black background SMART Maintenance Menu Password Center ID code identification number of the Center that the data terminal connects to C4656P013CA
9. C40040108AA 7 Close the paper drawer 4004 7715 01 208 Paper size label Drawer number label C4004U141AA CF2001P Affix the enclosed paper size label to Tray2 10 Adjusting the Options as shown NOTE With the CF2001P the adjustments of each option are performed with the Affix the enclosed drawer number label as servicing equipment Therefore start up the External Panel Controller and shown make the adjustments with the appropriate setting After adjusting the options restart the printer m Checking the Paper Reference Position for PF 118 NOTE e For details on the installing PF 118 refer to its Setup Instructions e To adjust PF 118 follow the instructions below e To exit the External Panel Controller refer to step 14 on page 24 1 Load A4 size or Letter size paper into the paper drawer of the optional paper feed unit 2 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual C4004P565CA 3 Click Machine Adjust Tech Rep Mode Fin z C4004P597CA 4004 7715 01 29 O NEXT CF2001P 4 Click PRT Area 7 Measure margin a from the edge of the paper to the pattern printed in the test page and then check that the width of the mea sured margin meets its standard width
10. NOTE e For details on installing DT 105 refer to the Setup Instructions included with it e To set the DI 105 follow the instructions below e To exit the External Panel Controller refer to step 14 on page 24 CF2001P lt Connecting the Telephone Cables gt e Connect the telephone cable to the jack marked LINE on the data terminal NOTE If the telephone cable is too short obtain a different cable with modular plugs e Connection examples lt When the telephone line is only for the data terminal gt Center Telephone Line LINE TEL DT 105 4656M007CA lt When the telephone line is for a phone and the data terminal gt Center Telephone Line LINE TEL DT 105 4656M008CA lt When the telephone line is only for a fax phone and data terminal gt Center Telephone Line LINE TEL LINE TEL FAX DT 105 4656M009CA NOTE For details on connecting the fax refer to the manual for the fax machine 4004 7715 01 36 CF2001P lt Precautions for Connecting a Telephone to the Data Terminal gt lt Modem Settings gt e Ifatelephone is connected to the data terminal check that the telephone complies 1 Plug inthe AC plug for the data terminal and with FCC part 68 then turn it on If a telephone which does not comply with FCC part 68 is used the telephone con nection may be cut when data terminal transmission begins 2 Check that the External Panel Controll
11. common screwdriver tighten the four screws shown in the illustration and then connect the harnesses of the IR port cable to the terminals on the converter TXA terminal brown harness TXB terminal red harness RXA terminal orange harness RXB terminal blue harness NOTE Be sure to connect the harnesses of the IR port cable to the specified terminals 4004 7715 01 EET CF2001P 6 Loosen the screw of the terminal and then E X Rite Caliblation attach the ground wire as shown NOTE Start up the External Panel Controller on the Notebook PC before turning on the printer If an error message appears follow the instructions described in the mes sage Do not quit the External Panel Controller while it is being used If it is quit ted restart the printer and the External Panel Controller 1 Start up the External Panel Controller on the Notebook PC C4004U604AA 2 Set the power switch to I 7 Attach the upper cover of the converter 8 Plug the power cable of the converter into an electrical outlet 9 Plug the power cable of the X Rite into an electrical outlet C4004U564AA 3 Make sure that the selector knob is set to B A C4004U598AA 4004 7715 01 _45_ CF2001P O NEXT Carnai Panai Carmo C4004P565CA C4004P597CA X Rite Calibration Sec aper 2176 29 follows T gata Progs START Poge Biar i pr ity out es in 2 Gradat
12. to an internal switchboard the time required to access the outside line varies depending on the type of system used Therefore enter pause or wait W codes for the time required to access the outside line e If the access time is 3 seconds or more enter wait codes by selecting the Energy Saver key e If the access time is less than 3 seconds enter pause codes by selecting the Inter rupt key 3 If the data terminal is connected to an internal switchboard where the internal and outside lines are of different systems enter a pulse code P for a rotary line or enter a tone code T for a push button line So a e e Display Extension key sharp Extension key asterisk 4 After the telephone number has been entered call the Center to inform them of the entered settings 4 Click END C4656P017CA 4004 7715 01 41 CF2001P lt Initial Transmission gt 3 Click the Panel Reset key in the External e To perform the initial user registration for the data terminal after the initial settings Panel Controller have been specified connect to the Center so the initial information can be sent to the data terminal Panel Reset Call the Center by telephone before and after the initial transmission for verification In addition after the transmission check that the data total counters etc has been sent correctly to the Center 4002U103EA 4 Click Fin Time sa
13. 7 Click DT ID so that it appears in white on a black background C4656P008CA SMART Maintenance 2 Using the keypad in the External Panel Controller enter the 7 digit ID code NOTE Enter the service representative s ID code C4656P014CA 8 Using the keypad in the External Panel gi Controller enter the 6 digit data terminal ID C4656P009CA 3 Click ID Code again so that it appears in Maintenance black on a white background NOTE i i2356 If the number is not 6 digits long add 0 at 4 Click DT Setting l the beginning DT Setting nn connie e ee ne C4656P015CA ber of the data terminal C4656P010CA 5 Click Password so that it appears in white on a black background C4656P012CA Ca n UUl 4004 7715 01 _ 40 CF2001P lt Setting the Telephone Number gt 1 Click TEL No so that it appears in white on a black background Maintenance 2 Click the Clear key in the External Panel Controller 3 Using the keypad in the External Panel Controller enter the 19 digit telephone number for the Center C4656P016CA NOTE 1 Check the screen in the in the External Panel Controller and make sure to enter the data correctly If an incorrect number is entered click the Clear key in the External Panel Controller and then re enter the data 2 If the data terminal is connected
14. Remove the screw at the bottom of the con verter and then remove the upper cover C4004U602AA C4004U557AA 3 Set the TERM switch S2 to ON as shown in the illustration NOTE e Set the button on the converter to Nor mal e In order to reduce the risk of damage to the circuit board due to static electricity do not touch the circuit board pattern e Do not change the setting of any switches other than those specified Aluminum tape C4004U603AA C4004U558AA 1 Remove the selector from its box 2 Remove the two screws from the selector and then remove the upper cover 3 Affix aluminum tape to the converter as shown in the illustration 4004 7715 01 _43 CF2001P O NEXT m Connecting the Equipment Cables 1 Insert a connector on the DIP382 cable 4 into the I O port on the side of the X Rite and then insert the other connector of the cable into port B on the selector C4004U559AA 2 Using the RS232 straight cable 5 connect the COM 1 port of the computer to port C on the selector NOTE Make sure that the RS232 straight cable is connected to the COM 1 port of the com puter EES BEES SEES ESE COS CIENTO SR i CO C4004U560AA 3 Using RS232 straight cable 6 connect DB25 of the converter to port A of the selec tor Red Blue Orange C4004U563AA C4004U561AA 4 Connect the IR port cable 8 to the printer Using a
15. a Terminal DT 105 2 9 Controller 10 B Finisher FN 107 1 U S A and Canada only 2 Not available if the MicroPress PrintLink 2020m is installed 10 A 10 Mailbin Sorter a 9 JS 1002 2 10 C Finisher FN 108 C4004U551CA 4004 7715 01 __NEXT CF2001P 2 Unpacking m Unpacking the Printer m Unpacking the Accessories 1 Open the printer box and then remove the box containing the imaging unit 1 Remove the accessories from the box and then check that the following are enclosed NOTE Remove the box containing the imaging unit before removing the box from around 1 Imaging units oonan eeen anne de deweanh eee haved hee eee ns 4 the printer 2 Power GO a erana n E E oedueretee a aeeneous eoee 444s 1 3 LED cleaning WOON 2 ae tee ees oe ee ee eee A A 1 2 Remove the box from around the printer 4 CED Cleaning paper lt 2 os tcseSh estes tad eoawane Rarer CREENA aE 1 3 Remove the printer from the plastic bag 5 Manual holder site 4 cnet cum ae ce Passcen cue Epo aE eee eee anee 1 4 Open the two handle covers and then pull out the handles 6 User ManU al 4 22 e5226eveeend Peet et eee cceetaweded wees eee e 1 7 Setup Instructions 2 44 ncuxs ee eet ace kee bheehneese bets eee ee ee 1 8 Warranty card 9 naaa aaea Ciketeveadedee bee eee ee hee ens 1 9 Power cord instruction 1 edeseenccbeeedevecserewas quedo ees 1 10 Paper size 1d Delis ct cue hee Baw ean ere heer he
16. anual 2 Click Utility 3 Click Users Choice Utility C4004P599CA a 1 S Of non use use the 10 4 Click Sleep Mode 5 Using the keypad in the External Panel Con troller enter the desired number of minutes and then click Enter NOTE Select the C Clear key to erase the entered number Click Exit Click Exit Check that the message displayed in the control panel changes from Alert Printing suspended to Info Exit the External Panel Controller NOTE Before connecting or disconnecting the har nesses of the IR port cable be sure to turn off the printer and the converter 4004 7715 01 _ 06 CF2001P NEXT 5 Load the paper into the drawer so that the 9 Loading Paper NOTE For more details about loading paper refer to the User Manual 1 Prepare paper that meets this product s specifications C4004U074AA 2 Pull out the paper drawer for Tray 1 3 Press down on the paper lifting plate until it locks into place C4004U072AA C4004U170AA 4 Slide the adjustable paper guides to fit the size of paper to be loaded C4004U073AA front side of the paper the side facing up when the package was unwrapped faces up NOTE e Do not load so much paper that the top of the stack is higher than the mark indicat ing the maximum paper capacity e Be careful not to to
17. d to the setting for al Thickt plain paper E 9 From the control panel select the size of the wa paper loaded into Tray 1 RI C4004U073AA A NOTE For details on specifying settings refer to the User Manual C4004U075CA 4004 7715 01 93 _ O NEXT C4004P565CA Tech Rep Mode C4004P597CA C4004PU10CA CF2001P 10 Check that the External Panel Controller 15 Check that the message displayed in the appears in the computer screen and then control panel changes from Alert Printing display the Tech Rep Mode screen For suspended to Info details about displaying the Tech Rep Mode screen refer to the Service Manual 16 Exit the External Panel Controller NOTE Before connecting or disconnecting the har nesses of the IR port cable be sure to turn 11 Click List Output off the printer and the converter 12 Click Image Processing 13 Click the Start key in the External Panel Controller A list of image processing set tings and the values of each counter are printed out on four sheets of A4 L size or Letter C size plain paper 14 Click Menu and then click Fin Time 4004 7715 01 24 CF2001P E To set the Energy Save Mode parameter Sy EE ETAM 4 Click Energy Save Mode NOTE When making settings according to the customers requests refer to the procedure described below
18. difference between the mea sured width and the standard width Left Margin 6 Print a test page and check the paper refer FTI ence position If the width of the measure margin does not meet its standard width follow the instruc tions described below C46580005CA 7 Open the paper drawer for the cassette that needs to be adjusted and then remove all of the paper 8 Loosen the two screws on the guide plate at the bottom of the paper drawer C4658U024AA 9 Adjust the guide plate to the appropriate position on the scale inside the paper drawer C4658U025AA 4004 7715 01 j CF2001P 10 Check that the message displayed in the control panel changes from Alert Printing suspended to Info 11 Exit the External Panel Controller E Checking and Adjusting the Paper Reference Position for PF 117 NOTE e For details on the installing PF 117 refer to its Setup Instructions e To adjust PF 117 follow the instructions below e To exit the External Panel Controller refer to step 14 on page 24 1 Load A4 size or Letter size paper into the paper drawer of the large capacity cabinet 2 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual Eih Erau wei Loman C4004P565CA 3 Click Machine A
19. djust C4004P597CA 4 Click PRT Area user Speed nans Correction H C4004P588CA ee 4004 7715 01 Oo CF2001P E Checking and Adjusting the Paper Reference Position for AD 14 5 Click Left Margin C4658P003CA 6 Select the key for the third paper drawer and then click the Start key in the External Panel Controller 4 Extent_ J EERE 5 82 onn L__tetter DB23a7 Paper 7 Measure the margin from the edge of the paper to the pattern printed in the top right corner of the test page Standard width a 3 0 mm 1 0 mm with Fiery X3e installed 5 0 mm 1 0 mm with MicroPress PrintLink 2020m installed Click the up and down arrows in the lower right corner of the screen to enter the differ ence in millimeters between the measured width and the standard width C4658U028AA 8 Print another test page and check the paper reference position NOTE e Perform the procedure below after adjusting the paper reference positions for the paper feed unit and the large capacity cabinet e For details on the installing AD 14 refer to its Setup Instructions e To adjust AD 14 follow the instructions below e To exit the External Panel Controller refer to step 14 on page 24 1 Load A4 size or Letter size paper into the paper drawer of the Tray1 2 Check that th
20. e External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual Hi C4004P565CA 3 Click Machine Adjust C4004P597CA 4 Click PRT Area FEolor Shite iA 1 Correction i Staple woe punch C4004P588CA 4004 7715 01 rec O NEXT CF2001P 5 Click Dup Left Margin 8 Measure the width of loss for the test pattern printed on the back of the test page NOTE Do not measure from the back of the test pattern Standard width a 3 0 mm 1 0 mm with Fiery X3e installed O gt 5 0 mm 1 0 mm with MicroPress PrintLink 2020m installed C4657P001CA 6 Click 1st If the measured width of loss does not meet its standard width click and in the lower right corner of the screen to adjust the yore width Print another test page and check the ee printed image Paper C4657U014AA Extent C4659P002CA 9 Adjust the paper reference positions for the 7 Click the Start key in the External Panel 2nd 3rd and 4th drawers in the same way Stop Controller by repeating steps 6 through 8 A test page is printed o NOTE The 4th drawer is only available if two optional paper feed units are insta
21. er NOTE e The toner bottles are not included A bottle of toner is needed for each color four in total and should be purchased separately e Be careful not to spill toner inside the printer or get toner on your clothes and hands If toner gets on your hands wash them using water and a neutral soap If toner gets in your eyes immediately rinse them and then consult a medical pro fessional 1 Grasp the toner hopper door as shown and then carefully swing the door up to open it 2 Open the yellow toner hopper lid leftmost by swinging it toward you The toner hopper lids are from the left yellow magenta cyan and black 3 Remove the yellow toner bottle from its packaging Hit the bottom of the bottle against a strong surface such as a desk or table four or five times from a height of about 10 cm 4 in Since the toner within the bottle may have become compacted be sure to break it up by performing this step NOTE Be sure to hit the bottom of the toner bottle against the strong surface the opening of the bottle should be pointing up While holding the bottle securely shake it well in all directions to mix up the toner With the rounded side marked with W of the bottle mouth facing towards you place the toner bottle on top of the hopper and then press down on the bottle until it snaps into place 4004 7715 01 _g3_ CF2001P NEXT 9 Carefully close the yellow toner hopper lid
22. er appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual lt Data terminal specifications gt Product name DT 105 Data Terminal Transmission speed 2 400 bps max AEEA Telephone line General public telephone line analog dual line 3 Click SMART Power requirements DC5 2V supplied via the AC adaptor Current consumption 600 mA DC resistance 1490 4 Click Modem 5 Click END j System Selection C4656P002CA lt Transmission Settings gt 1 Click Common DT C4656P003CA U UUU UUU UUSII 4004 7715 01 _37_ DORPE O NEXT CF2001P 2 Click Dial Mode lt Date Time Settings gt 1 Click Date Time Input C4656P004CA 3 Select the dial mode of the user s telephone lt lt CA656PO03CA line SMART Common DT eno 2 Click Year click the Clear key in the External Panel Controller and then use the FROLANY oee Pulse i keypad in the External Panel Controller to i enter the correct year Dial Mode 4 Click END C4656P005CA 3 Enter the correct settings for Month Date and Hour 5 Click Auto Receive C4656P007CA 4 Click SET C4656P004CA 6 Click Disable SMART Common DT eno _ Auto Receive
23. ge quality C4004U215AB 10 While keeping the bottom of the imaging unit supported with your left hand carefully insert the imaging unit with your right hand as shown until the cartridge snaps into place C4004U216AB 9 Keeping the imaging unit level insert the imaging unit as far as possible into the imag ing unit compartment Insert the imaging unit with the protective sheet s attached 11 Pull out the empty imaging unit cover The empty imaging unit cover for the black imaging unit can simply be pulled out even if the protective sheets on the imaging unit become caught on the toner hopper lid C4004U051AC C4004U054AB 4004 7715 01 CF2001P O NEXT 12 Separate the top and bottom halves of the empty imaging unit cover s Bottom cover NOTE Since the bottom half of the imaging unit cover will be used when the imaging unit is replaced again store it in a safe place C4004U055AA 13 Carefully swing the release lever back up to 4 its original position pushing it in until it locks e into place Tere C4004U173AA V al ls A y Y A Ni u EI Lio NOTE If the release levers are not correctly posi tioned the front door cannot be closed Metal terminals C4004U056AA 14 Remove the packing materials from the remaining imaging unit slots and then install the magenta cyan and black imaging units in the same way described in steps 2 th
24. h your hands If the roller has been touched wipe it with a dry cloth 2 Remove the 2 pieces of tape shown in the illustration from the paper lifting plate aper take up roller 3 Remove the 2 pieces of packing material from the paper lifting plate 4 Close the paper drawer 5 Pull out the paper drawer for Tray 2 NOTE Be careful not to touch the surface of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth 6 Remove the 3 pieces of tape affixed to the paper lifting plate as shown 7 Remove the packing material from the paper lifting plate 8 Close the paper drawer 4004 7715 01 CF2001P NEXT 3 Installing the Units E Installing the Imaging Units C4004U011AA C4004U047AA 3 Swing the release lever toward you Grasp the handle of the front door and then carefully swing the door open to the right as shown C4004U144AA Pinch the release lever for the yellow imag ing unit The colors of the imaging units are from the left yellow magenta cyan and black Protective tape C4004U049AB C4660U001AB 4 Remove the packing material from the imag ing unit slot 5 Remove the yellow imaging unit from its box and its protective plastic bag and then place the imaging unit on a stable level surface such as a table NOTE e The imaging unit can easily be damaged by light Therefore
25. ibration of AutoScan Densitometer before going to do the calibration of Priner Engine Wouk you do a l Ves Skio Cancel C4004P572CA Read the Auto Cal Strip lt Back C4004P573CA 7 10 After the test patterns are printed check that the message appears and then click the Start key in the External Panel Controller Check that the dialog box appears set the selector knob to B and then click OK in the dialog box Check that the dialog box appears and then click Yes in the dialog box When the dialog box appears the auto cal strip can be read Prepare the auto cal strip 4004 7715 01 s0 CF2001P 11 Insert the auto cal strip into the X Rite NOTE Insert the auto cal strip after INSERT CAL STRIP appears on the X Rite display SSS P aan Sr Se C4004U574AA fs 0 08 0 08 0 06 CALIBRATION OK OOOO C4004U594CA 12 Check that the dialog box appears gt gt Read the pattern of Cyan NOTE The dialog box appears if the auto cal strip was read correctly Read the pattern of Magenta Read the pattern of Yellow Read the pattern of Black 2 edge patches lt Gude 10 2 center patches lt Guide 30 gt Cancel C4004P575CA SERRE OLLIE gt gt Read the pattern of Cyan Read the pattern of Magenta Read the pattern of Yellow Read the pattern of Black 2 edge patches lt Guke 10 OKIE 2 cente
26. ides are C4004U170AA 7 Close the paper drawer 8 Make sure that the media type selection dial m on the drawer is turned to the setting for ain I Thickt plain paper OHP Plain Ry Thick1 E 9 From the control panel select the size of the test paper loaded into Tray 1 NOTE For details on specifying settings refer to the User Manual C4004U075CA pushed up against the edges of the paper Setting Up the Servicing Equipment Set up the equipment in order to print a test pattern and make the necessary adjustments NOTE Do not turn on any equipment until you are instructed to do so BES RX BEESESS ECS OSE OD COSECSOS lt lt SSS RIED E SSZ GES Notebook PC Starts the External Panel Controller for adjustment X Rite DTP32 Color Tone Tester Selector Switches between the Notebook PC and the X Rite CF2001P DTP32 cable Connects between the X Rite and the connector A of the selector RS232 straight cable Connects between COM1 port of the Notebook PC and the connector C of the selector RS232 straight cable Connects between the converter and the connector B of the selector Converter Converts the RS422 connector to the RS232 connector IR Port cable Connects between the CF2001P and the converter 12 CF2001P E Setting Up the Converter 7 E Setting Up the Selector 3 1 Remove the converter from its box C4004U601AA C4004U556AA 2
27. ion Adwusteent wal be printed Avai 1ab19 paper sizes A4 D lette D C4004P567CA Test patterns Ja C4004U568AA 4 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual NOTE If the basic screen does not appear in the External Panel Controller turn the printer off Restart the External Panel Controller and then turn the printer on again 5 Click X Rite Calibration in the Tech Rep Mode screen 6 Check the message that appears and then click the Start key in the External Panel Con troller Test patterns are printed for the four colors Cyan Magenta Yellow Black NOTE e Since it may take some time to output the test patterns about 2 minutes wait until printing is finished e During printing do not open the front door If the front door is opened restart the procedure from step 1 X Rite Calibration Press START to enter the test pattern read mode correct mode Do not open the front door in test pattern read mode correct mode X If you did be sure to restart from test pattern output for correction C4004P569CA Switch the selector to X Rite and press the OK button Press the Cancel button if you do not went to start X Rite read mode cae C4004P570CA C4004U571AA Recommend the cal
28. leave the imaging unit in its protective plastic bag until immedi ately before it is to be installed After removing the imaging unit from its protective plastic bag make sure that it is not exposed to light and immediately install it into the printer 6 Hold the imaging unit in both hands tilt it to the left and then lightly shake it twice in the direction of the tilt Next hold the unit tilted to the right and then lightly shake it twice in the direction of the tilt 4004 7715 01 CF2001P 7 Remove the protective tape from the imag ing unit NOTE Be sure to insert the imaging unit until the end of the bottom imaging unit cover con tacts the back of the imaging unit compart Protective sheet Zz NOTE The clear plastic protective sheet is not packing material therefore do not remove ment it SOOO le C4004U193AA The additional protective sheet indicated by the shaded area is only attached to the a black imaging unit NOTE Do not insert the imaging unit into the com partment at an angle 8 Keeping the imaging unit level pick it up by supporting it on the bottom with your left hand and on the bottom at the front with your right hand NOTE When holding the imaging unit be sure to hold it by its bottom cover If the top imaging unit cover is held it may fall off or the PC drum installed on the imaging unit may become damaged resulting in decreased ima
29. lled Start C4004U596CA Ce e aa 4004 7715 01 _ 34 CF2001P E Checking the Hole Punching Positions for FN 107 6 Click Hole Punch Staple Hole Punch NOTE e For details on the installing FN 107 refer to its Setup Instructions e To adjust FN 107 follow the instructions below e To exit the External Panel Controller refer to step 14 on page 24 Staple e Ho1le Punch 1 Unplug the power cord and then turn off the printer C4683P005CA 7 Click the Start key in the External Panel 2 Load A4 size or Letter size paper in land Controller scape orientation into Tray 1 3 Check that the External Panel Controller 8 Fold the paper that Is fed out in half and c check that the punched holes are aligned appears in the computer screen and then o display the Tech Rep Mode screen For details about displaying the Tech Rep Mode Standard position 2mm screen refer to the Service Manual NOTE a If the punched holes are not at their stan C4004P565CA dard positions adjust the hole punching 4643U031AA position 4 Click Machine Adjust C4004P597CA 5 Click Staple Hole Punch Machine Adjust Menu FEolor Shift ST 1 Correction i C4004P588CA OCO S E SS SSSSSSSSSSSSJqJJqJJJJ_JqQz___________L_ _L_Ss gt z 4004 7715 01 35 _ E Setting DT 105 USA and Canada only
30. n et Kak eee ek eee 1 11 Gable clamp cc2c4 00ne2cteeaeGeteueh aaee doedhbeakeekeses lt 1 12 SUpport Abele secer ery crews dd rrine trr EA OERA ESE EEDE 1 13 Additional information Storing the LED cleaning tool n annann ea 1 1 For Particular area only 2 The LED cleaning tool and its paper are not used during setup Since they will be needed when the imaging unit is changed or the printer is cleaned keep them in a safe place for later use C4004U003AA 3 U S A and Canada only 5 Grasp the two handles on the right side of the printer and the two grips on the left as shown in the illustration and then while keeping the printer level remove it from its box NOTE The printer weighs about 77 kg 169 3 4 Ibs The printer must be lifted by at least two people When lifting the printer be care ful not to strain your back C4004U004AA 6 Carefully place the printer on a level and sturdy surface such as a table 4004 7715 01 oO CF2001P NEXT E Removing the Protective Tape and Packing Materials lt Outside Surface of the Printer gt C4004U005AA sj _ Y L ir W q i e LSJ a ALLL Packing material Paper take up roller i Remove the tape affixed to the outside sur face of the printer C4004U006AA Pull out the paper drawer for Tray 1 NOTE Be careful not to touch the surface of the paper take up roller wit
31. n the type of servicing being performed 1 Check that the External Panel Controller appears in the computer screen and then display the Tech Rep Mode screen For details about displaying the Tech Rep Mode screen refer to the Service Manual Eih Eana wei Cor ati C4004P565CA 2 Click System Input C4004P597CA 3 Click Unit Change System Input Menu C4004P584CA Un Toner Waste Toner Bottle Dil Coating Uni Fusing Unit Fusing Web Unit C4004PU02CA 4 Click User or Service to select whether each unit should be replaced by the user or the service representative 5 Click END 6 Click Menu and then click Fin Time 4004 7715 01 90 _ CF2001P NEXT E Printing the List 5 Load the prepared A4 L size or Letter L size plain paper into the paper drawer 1 Prepare A4 size or Letter size plain paper 2 Pull out the paper drawer for Tray 1 C4004U087AA 6 Slide the adjustable paper guides against the edges of the paper NOTE Check that the adjustable paper guides are 3 Press down on the paper lifting plate until it pep gP pushed up against the edges of the paper locks into place 7 Close the paper drawer 4 Slide the adjustable paper guides to the A4 L or Letter L paper size 8 Make sure that the media type selection dial i on the drawer is turne
32. ni Maintenance nan 1 Click Initial Transmission C4004P566CA 2 After the initial transmission is completed NOTE This completes input of the Maintenance Center settings If the Billing Center settings must be specified perform it in the same way C4656P019CA Not answering The other line is busy DT modem error Dialing DT Connection failed 4004 7715 01 _A0
33. outlet C4004U139CA EE 4004 7715 01 10 CF2001P 6 Installing the Manual Holder 7 Checking the Operation of the Printer 1 Insert the tab on the bottom of the manual holder into the slot in the printer as shown in NOTE the illustration Before adjusting the printer be sure to install the interface kit and the control ler For more details on their installation refer to their manuals E Loading Test Paper Load test paper specifically for use with X Rite calibration C4004U553AA 1 Prepare A4 size or Letter size plain paper 2 Insert the tabs on the left and right sides of 2 Pull out the paper drawer for Tray 1 lt a ee the manual holder into the corresponding a Om slots in the printer IY T F on S f NY ME C4004U071AA C4004U554AA oF NOTE 3 Press down on the paper lifting plate until it locks into place If the optional finisher is used attach the manual holder to the back of the finisher at Say the position shown using the same proce A dure described above N C4004U072AA C4004U098AA 4 Slide the adjustable paper guides to the A4 C or Letter C paper size C4004U073AA 4004 7715 01 11 NEXT CF2001P 5 Load the prepared A4 C size or Letter C size plain paper into the paper drawer C4004U074AA 6 Slide the adjustable paper guides against the edges of the paper NOTE Check that the adjustable paper gu
34. r patches lt Guide 30 gt ok p x P gt C4004U576AA C4004U577AA Cancel C4004P578CA 13 Prepare the cyan test pattern set the X Rite guide to 10 and then feed the pattern in direction 1 to read the row represented by A Align the test pattern with the guide and insert the pattern into the X Rite The arrows indicate the direction that the pattern should be fed into the X Rite 14 Check that the area indicated in the dialog box appears in OK NOTE The area indicated appears in OK if the pattern was read correctly 4004 7715 01 ae y O NEXT CF2001P 15 Feed the test pattern in direction 2 to read 18 Check that the area indicated in the dialog 3 the row represented by B gt gt and the puicions of Open box appears in OK et When feeding the test pattern to read the BER an row represented by B turn the paper to paar NOTE a feed it in the correct direction without adjust a eR THE ETa The area indicated appears in OK if the ing the X Rite guide 2 center patches lt Guite 30 gt OK Cacen pattern was read correctly NOTE C4004P580CA ra mer _ om When reading the row in the test pattern PARERE M E te a represented by B do not change the set i the test ies to rea 2 4 ting of the X Rite guide 3 1 the row represente y D C4004U576AA ie When feeding the test pat
35. rough 13 NOTE Be sure to install the imaging units in their correct slots C4004U149AB 15 After all four imaging units have been installed grasp the handle of the front door and then carefully swing the door closed as shown C4004U013AA E Installing the Oil Coating Unit 1 Grasp the upper right side door as shown and then carefully open the door completely while making sure to support it NOTE Be sure to support the upper right side door while carefully opening it otherwise it may become damaged NOTE Do not touch the metal terminals at the front of the fusing unit otherwise damage may occur due to static electricity 4004 7715 01 CF2001P NEXT 2 Remove the two pieces of tape from the lock levers of the oil coating unit shown 5 Swing the oil coating unit up to install it C4004U150AB 3 Remove the oil coating unit from its box NOTE When picking up the oil coating unit pick it up by the two handles one on each end of the unit with both hands 6 Secure the oil coating unit by moving the two lock levers one on each end of the unit toward you C4004U151AA 4 Insert the oil coating unit making sure that the two pins one on each end of the unit fit 7 Grasp the upper right side door as shown into the notches in the printer and then carefully close it C4004U152AB C4004U174AA 4004 7715 01 CF2001P NEXT E Filling the Ton
36. tern to read the a l row represented by squares turn the paper 16 Check that the area indicated in the dialog to feed it in the correct direction without gt gt Read the pattern of Cyan box appears In OK oe adjusting the X Rite guide Read the pattern of Magenta Bo i Re anamin NOTE m NOTE AEA gt BKK AS The area indicated appears in OK if the n When reading the row in the test pattern 2 center patches lt Guide 30 gt Ceca pattern was read correctly J i C A represented by D do not change the set ting of the X Rite guide C4004P579CA AAA 17 Turn the cyan test pattern to its original ori 20 Check that the area indicated in the dialog 3 1 entation set the X Rite guide to 30 and box appears in OK lete then feed the pattern in direction 3 to read NOTE EA the row represented by C m The area indicated appears in OK if the ne pattern was read correctly oz am mn B D agi C A 2 4 C4004U576AA eee n 4004 7715 01 18 _ gt gt Read the pattern of Magenta Read the pattern of Yellow Read the pattern of Black Zedge patches lt Gude 10 gt 2 canter patches lt Gude 3D J C4004P582CA gt gt Read the pattern of Magenta Read the pattern of Yellow Read the pattern of Black Gude to
37. uch the surface of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth 6 Slide the adjustable paper guides against the edges of the paper NOTE Check that the adjustable paper guides are pushed up against the edges of the paper Close the paper drawer Turn the media type selection dial on the drawer to the setting for the type of paper loaded From the control panel select the size of the paper loaded into Tray 1 NOTE For details on specifying settings refer to the User Manual 4004 7715 01 97 NEXT CF2001P E Tray 2 C4004U077AA C4004U078AA 5 Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Prepare paper that meets this product s specifications NOTE e Do not load so much paper that the top of the stack is higher than the mark indicat C4004U079AA ing the maximum paper capacity e Be careful not to touch the surface of the paper take up roller with your hands If the roller has been touched wipe it with a dry Press down on the paper lifting plate until it cloth locks into place Pull out the paper drawer for Tray 2 6 Slide the lateral guides against the edges of the paper NOTE Check that the lateral guides are pushed up against the edges of the paper Slide the adjustable paper guides to fit the size of paper to be loaded
Download Pdf Manuals
Related Search