Chief Manufacturing TV Mount MSP-DCCMD User's Manual
Contents
1. 150 NOTE e Foraflush mount application perform the Attach Mount to Wall Bracket on page 6 and then perform the Flush Mount Centris Bracket to Display on page 7 e For a recessed mounting application omit the procedure to Attach Mount to Wall Bracket on page 6 and proceed to the Recess Mount Centris Bracket to Display on page 7 Attach Mount to Wall Bracket 1 Align the top of the mount 10 with the top of the wall bracket 150 Push the bottom of the mount against the bottom of the wall bracket until the mount fits snugly in place see Figure 3 2 Using the 5 32 hex wrench 180 secure the mount to the wall bracket by tightening the set screw see figure 3 Ensure set screw engages back side of bracket to properly secure mount Set Screw ___ W 180 A Figure 3 Attach Mount to Wall Bracket Installation Instructions Model MSP DCCMD INSTALLATION 100mm x 100mm Flush Mount Centris Bracket to Display Centris Bracket 1 Install two M4 x 12mm screws 60 into the top mounting holes not shown on the display 2 Align the mounting holes on the Centris bracket with the screws installed on the display Hang the display on the Centris bracket see figure 4 3 Install two remaining M4 x 12mm screws 60 into the bottom mounting holes on the display Recess Mount Centris Bracket to Display Use one of the following screw and spacer combinations 40 with2. into the four mounting holes on the interface bracket 130 see figure 9 4 Slide 4 retaining spacers 120 onto four M6 screws 30 NOTE The arrow on the interface bracket 80 must point toward the top of the display 5 Align interface bracket 130 with screws 30 and spacers 120 with mounting holes in display back 6 Tighten all screws Attach Display to Centris Bracket 1 Start two M4 x 5mm Phillips pan head screws 70 into the top two mounting holes of the previously attached interface bracket see figure 10 2 Hang the mount from the two screws started in Step 1 3 Install the remaining two M4 x 5mm Phillips pan head screws 70 into the bottom mounting holes of the display 4 Secure the display to the mount Centris bracket by tightening all four M4 x 5mm Phillips pan head screws 70 see figure 10 Model MSP DCCMD Arrow must point to top of display Figure 8 Attach 400mm x 200mm Interface Adapter Ro Arrow must point to top of display t t 30 130 Figure 9 Attach 550mm x 235mm Interface Adapter Centris Bracket XS Es Display Figure 10 Attach Display to Centris Brachet Model MSP DCCMD CABLE MANAGEMENT WARNING Make sure your cables do not run through a pinch point 1 Connect and secure power audio video cables making sure to leave sufficient slack to allow for movement of the display 2 R
3. 100 or 50 with 110 CAUTION If your display uses a screw size other thanM4 x 20mm or M4 x 30mm DO NOT use the M4 x 20mm or M4 x 30mm screws Using the wrong screws could result in damage to your display Display Figure 4 Flush Mount Centris Bracket to Display 1 Select four M4 screws 40 or 50 and four retaining spacers 100 or 110 from parts bag 2 Place display face down on a clean dry surface 3 Install four M4 screws 40 or 50 into the four mounting holes on centris bracket see figure 6 4 Slide 4 retaining spacers 100 or 110 onto four M4 screws 40 or 50 5 Align centris bracket with screws 40 or 50 and spacers 100 or 110 with mounting holes in display back 6 Tighten all screws Figure 5 Recess Mount Centris Bracket to Display Model MSP DCCMD INSTALLATION 200mm x 100MM Attach Interface Adapter to Display 1 Select six M4 screws 80 and six spacers 190 from parts bag Place display face down on a clean dry surface Install six M4 screws 80 into the six mounting holes on the interface bracket 140 see figure 8 Slide six retaining spacers 190 onto six M4 screws 80 NOTE The arrow on the interface bracket 140 must point toward the top of the display 5 Align interface bracket 140 with screws 80 and spacers 190 with mounting holes in display back 6 Tighten all screws Attach Display to Centris Bracket 1 Start two M4 x
4. 8mm Phillips pan head screws 70 into the top two mounting holes of the previously attached interface bracket see figure 7 Hang the mount from the two screws started in Step 1 Install the remaining two M4 x 8mm Phillips pan head screws 70 into the bottom two mounting holes of the display secure the display to the mount Centris bracket by tightening all four M4 x 8mm Phillips pan head screws 70 see figure 7 Installation Instructions 140 Display Figure 7 Attach Diaplay to Centris Bracket Installation Instructions INSTALLATION 400mm x 200MM and 550mm x 235MM Attach 400mm x 200mm Interface Adapter NOTE Used for 400mm x 200mm hole patterns 1 Select six M6 screws 30 and six spacers 120 from parts bag 2 Place display face down on a clean dry surface 3 Install six M6 screws 30 into the six mounting holes on the interface bracket 130 see figure 8 4 Slide six retaining spacers 120 onto six M6 screws 90 NOTE The arrow on the interface bracket 130 must point toward the top of the display 5 Align interface bracket 130 with screws 30 and spacers 120 with mounting holes in display back 6 Tighten all screws Attach 550mm x 235mm Interface Adapter NOTE Used for 550mm x 235mm hole patterns 1 Select four M6 screws 30 and four spacers 120 from parts bag 2 Place display face down on a clean dry surface 3 Install four M6 screws 30
5. framework The structure to which the JWD wall mount is anchored must be capable of supporting five times the total weight of the mount and all attached equipment e If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 e Ifa defect is discovered after Dell s initial 21 day Customer Satisfaction period Chief Mfg will at its option repair or replace the product at no charge provided it is returned during the warranty period Please note contact information for Chief Mfg listed below CHIEF MANUFACTURING INC 8832 000088 Rev C I 1 800 582 6480 952 894 6280 FAX 952 894 6918 2006 Chief Manufacturing IF 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com Ideas Supporting Ideas SAVAGE MINNESOTA 55378 USA Printed in USA 03 06 Model MSP DCCMD Installation Instructions A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Improper installation can result in serious personal injury Make sure that the structural members can Support a redundant weight factor five times the total weight of the equipment If not reinforce the structure before installing the JWD WARNING Be aware also of the potential for personal injury or damage to the unit i
6. six M4 x 16mm screws 80 and six spacers 190 are used to attach the interface adapter 140 to the display The M6 x 20mm screws 30 are used with spacers 120 and the interface adapter 130 tThe M4 x 8mm screws 70 are also used to attach the Centris interface to the interface adapter 140 Model MSP DCCMD Installation Instructions WALL BRACKET INSTALLATION Secure Wall Bracket WARNING It is the responsibility of the installer to verify that the surface to which the mount is anchored will safely support the combined load of all attached components and equipment To install the mount 1 Determine the exact mounting location prior to installation considering the units swing and extension radius 2 Using the wall bracket 150 as a template mark the two pilot holes for mounting the wall bracket see figure 2 3 Drill two 1 4 pilot holes a minimum depth of 2 into the wood stud NOTE Make sure the wall bracket is level before installing the lag bolts 4 Using a 9 16 socket wrench install two lag bolts 20 to secure the wall bracket 150 to the wall Do not overtighten the lag bolts IMPORTANT Overtightening lag bolts may cause bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in step 2 below If this occurs remove bracket install 3 8 steel washers as required between bracket and wall surface and reinstall bracket a
7. steps as follows e Select mounting configuration e 100mm x 100mm Centris mounting flush and recessed 200mm x 100mm Centris mounting with interface adapter the interface adapter that accommodates two mounting hole patterns 400mm x 200mm and 550 x 235mm e Connect cables e Make adjustments Model MSP DCCMD Installation Instructions PARTS Centris Interface see notes Set Screw see notes 130 140 Zi 150 Oo on O O 160 N O CO O CO O Figure 1 JWD PARTS Installation Instructions Model MSP DCCMD PARTS Continued Table 2 below provides a list of the JWD parts Table 2 JWD Parts ITEM DESCRIPTION USED WITH NOTES peel mn EE CE IL o PR PARE MACINES RE rom 6 USEWTHTOANO TA PHILLIPS PAN HEAD MACHINE SCREVV M4 x 12mm 4 USE VVITH CENTRIS INTERFACE CI SC UREWTTHO 9 PRLLPS I rion farriuocnowsmces CI TO 3 8 THICK NYLON SPACER THICK NYLON SPACER 3 8 THICK NYLON SPACER 4 USEWITH50 5 16 THICK NYLON RETAINING SPACER USE WITH 30 75 Outside Diameter INTERFACE ADAPTER 400mm x 200mm and USE WITH 30 AND 120 550mm x 235mm C S SE WTHTORNO GD rm ennonsenceR CEL NOTES tThe M4 x 12mm screws 60 are used on the Centris interface for flush mount applications The M4 x 30mm screws 40 with spacers 100 are for recessed mount applications M4 x 20mm screws 50 with spacers 110 are for recessed mount applications The
8. ATION 400mm x 200MM and 550mm x 235MM 9 Attach 400mm x 200mm Interface Adapter 9 Attach 550mm x 235mm Interface Adapter 9 Attach Display to Centris Bracket 9 CABLE MANAGEMENT ccccecceeeeeeeseeeeeeees 10 ADJUSTMENTS sorar site Ge nt il 10 LATERAL TENSION ADJUSTMENT 10 PITCHADIUST MENT cicscncixteincatincereeiene 10 TOOLS REQUIRED FOR INSTALLATION e Electric drill and bit set e Hex wrench set e Phillips screwdriver e Level NOTE Other tools may be required depending on the mounting surface and method of installation Model MSP DCCMD Inspect The Unit Before Installing WARNING Watch for pinch points Do not put your fingers between movable parts 1 Carefully inspect the mount for shipping damage If any damage is apparent call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage NOTE Read all instructions before starting installation 2 Lay out components to ensure you have all the required parts before proceeding see JWD drawing on page 4 SPECIFICATIONS Table 1 below provides the JWD specifications Table 1 JWD Speifications Depth from 2 11 16 68mm Wall Maximum 20 3 8 51 8cm Extension Dimensions W 13 1 8 x 14 11 16 x 2 11 16 xHxD 308 x 373 x 68mm Weight 75 lbs 34kg Capacity INTRODUCTION The installation process involves three key
9. INSTALLATION INSTRUCTIONS Medium Flat Panel Dual Swing Arm Wall Mount JWD Model MSP DCCMD The JWD single swing arm wall mount was designed for mounting a medium sized flat panel display The JWD can swing out from the wall or fold against the wall depending on your ergonomic need The mount itself can be tilted 15 The amount of tilt left and right depends on the size and location of the display The JWD is shipped with the VESA 100mm 100mm Centris interface which is compatible with most medium flat panels To accommodate the mounting hole patterns on existing medium flat panels that are offered in different sizes the JWD is supplied with two interface adapters listed below e The 200mm 100mm interface adapter e The interface adapter that accomodates the 400mm 200mm and 550mm 235mm hole patterns The JWD will more than likely adapt to your medium flat panel display providing that your display does not exceed the specified weight rating BEFORE YOU BEGIN CAUTION To prevent damage to the JWD which could affect or void the Factory warranty and to the equipment that will be attached to it thoroughly study all instructions and illustrations before you begin the installation Pay particular attention to the Important Warnings and Cautions on Page 2 e The maximum weight to be installed on the JWD wall mount is 75 pounds 34 kg e The JWD wall mount is designed to be installed using wall studs or supporting
10. f it is not adequately mounted WARNING The installer is responsible for verifying that the wall to which the JWD is anchored will safely support the combined load of all attached components or other equipment WARNING The weight of the display placed on the JWD must not exceed 75 Ibs 34 kg the maximum load capacity of the JWD WARNING Watch for pinch points Do not put your fingers between movable parts WARNING Make sure the mount and brackets are correctly oriented CAUTION Check the unit for shipping damage before you begin the installation DIMENSIONS 514 87 20 35 Front Vievv Rear Vievv Installation Instructions CONTENTS IMPORTANT WARNINGS AND CAUTIONS 2 DIMENSIONS sea a N 2 TOOLS REQUIRED FOR INSTALLATION 3 Inspect The Unit Before Installing 3 SPECIFICATIONS em dottetei tanda 3 INTRODUCTION a ostenten asmecontt tenies 3 PARTS COMMMUCG deri distints ialms 5 WALL BRACKET INSTALLATION 6 Secure Wall Bracket o o o o o o o o oe 6 Attach Mount to Wall Bracket 6 INSTALLATION 100mm x 100mm 7 Flush Mount Centris Bracket to Display 7 Recess Mount Centris Bracket to Display 7 INSTALLATION 200mm x 100MM cccecceceeeereee 8 Attach Interface Adapter to Display 8 Attach Display to Centris Bracket 8 INSTALL
11. oute power audio video cables under each arm allowing sufficient slack in cables for extension and avoiding pinch points 3 Secure cables using two cover plates 160 and four screws 90 see figure 11 ADJUSTMENTS LATERAL TENSION ADJUSTMENT CAUTION Overtightening adjustment will cause excessive wear 1 Using a 3 16 hex wrench 170 slightly tighten or loosen lateral tension adjustment bolts see figure 12 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained PITCH ADJUSTMENT CAUTION Overtightening adjustment screw will cause excessive wear NOTE Remove display to make pitch adjustment 1 Check adjustment screw on the Centris interface to ensure that the screw is tight see figure 13 2 Ifneeded use a 3 16 hex wrench 170 to tighten the screw Figure 11 Cable Management 10 Installation Instructions Lateral Tension Adjustment Bolts Figure 12 Adjust Lateral Tension Pitch Tension Adjustment Screw Figure 13 Pitch Adjustment
Download Pdf Manuals
Related Search