Chief Manufacturing TV Mount mcd User's Manual
Contents
1. Attaching Mount to NPT Pipe WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 LBS CAUTION Watch for pinch points Do not place fingers between moveable parts installing or positioning display on mount Always use two people and proper lifting techniques when 1 Thread the MCD mount A onto the existing 1 1 2 NPT or 2 Lower display into place listening for audible click to NPSM pipe not included until tight with a minimum of four ensure recessed area of mounting buttons are properly threads engaged See Figure 1 1 2 Faure d tighten the 5 16 18 x 3 8 set screw B See 6 Hepat St ps fand for second display seated in lower area of mounting holes and ClickConnect mechanism has engaged See Fig 2 3 and 4 NPT Pipe Back d of Display t Figure 1 MSBV interface bracket example only Attaching Interface Bracket to Displays Figure 3 1 Attach MSBU or MSBV interface bracket to displays following instructions included with MSBU MSBV interface bracket kit Attaching Displays to Mount 1 While supporting both sides of display align four mounting buttons on interface bracket with four mounting holes in mount See Figures 2 3 and 4 MCD Series Installation Instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT2. Chiave a punte aperte Steeksleutel Cle a fourche Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Installation Instructions MCD Series TOOLS REQUIRED FOR INSTALLATION 5 32 Included 9 16 PARTS B 1 5 16 18 x 3 8 C 1 5 32 MCD Mount Installation Instructions MCD Series INSTALLATION WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the A component IMPORTANT These installation instructions assume that a 1 1 2 NPT or NPSM following ANSI ASME g pose Display B1 20 1 Schedule 40 0 154 minimum thickness steel or aluminum ASTM B221 threaded extension column not included has been properly installed and is in place Figure 2
3. factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the supporting structure and the mount does not exceed 250 Ibs 113 4 kg 125 lbs 56 7 kg each faceplate The weight capacity of the MCD may be LIMITED to the lowest weight capacity of any other component located between the MCD and the supporting structure WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The MCD Series mounts are designed to be mounted to a 1 1 2 NPT or NPSM following ANSI ASME B1 20 1 Schedule
4. 40 0 154 minimum thickness steel or aluminum ASTM B221 threaded extension column not included NOTE The MCD Series includes e Accessory Model MCD6000 to be used with Listed Chief Accessory MSBU or MSBV interface brackets not included SAVE THESE INSTRUCTIONS Installation Instructions MCD Series 2 VO SPUR SEN INTERFACE BRAC HET o _ o 97 AV TRE SEUIN SEV INTERFACE RACKET ED FOR TO UR DISPLAY d FILLED DEPTH AND WAY A ERECT LOCATION OF DISPLAY ON TREN CURT T SEE MSBU MSBV DRAWING ALSO d 01 Ha o x o TOP 4 OUETIE G BUTTON ON SUE SEY BRACKET GOES HERE Tes 1 20 ry 9 OUO f oO 5 e 418 H K FACE TITS sel 11 02 T PRE ic NS N FACE TILT sel Sal e EIN ETE CER TER ja a OF DISPLAY ovo O o ovog RS 7 68 5 44 10 15 gt DIMENSIONS INCHES Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas
5. Ensure mounting buttons are completely engaged in mounting holes Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 4 RU To use as a more 1 permanent lock remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 4 Removing Displays 1 Disconnect all power audio video cables 2 Remove bolt or padlock from faceplate if used See Figure 5 NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 3 Pull back on flag on upper mounting hole and press pin down into Open position See Figure 5 WARNING THE DISPLAY MAY WEIGH IN EXCESS OF 40 LBS EACH Always use two people and proper lifting techniques when installing or positioning display 4 Carefully lift display from mount 5 Lift up on pin and place flag back against faceplate to return it to Closed position See Figure 5 Remove bolt or padlock if used Pin in Closed position Move to Open position to remove display Pin in Open position Move to Closed position after display is removed Figure 5 Adjusting Displ
6. INSTALLATION INSTRUCTIONS Dual Ceiling Mount CS CHIEF MCD Series Our Mounts Your Vision MCD Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and ClickConnect are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of
7. ay CAUTION Watch for pinch points Do not place fingers between movable parts Installation Instructions MCD Series Adjusting Roll 1 Loosen the Nylock roll adjustment nut on back of mounting plate See Figure 6 2 Tilt the faceplate left or right as required 3 Tighten nut NOTE Do NOT over tighten fasteners Adjusting Pitch 1 Adjust display to the desired pitch 2 Tighten the pitch adjustment screw to hold mount in position See Figure 6 CA Pitch Adjustment Screw SS 7 Roll Adjustment Nut Figure 6 MCD Series Installation Instructions USA International CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002593 Rev00 2014 Milestone AV Technologies www chiefmfg com 05 13 gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
Download Pdf Manuals
Related Search