Chief Manufacturing PNRIW User's Manual
Contents
1. Figure 2 2 Secure swing arm to PAC501 using four button head cap screws C four lock washers D and four flat washers E See Figure 3 Figure 4 Installation Instructions Display Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT install display in a manner other than that specified by the manufacturer Certain displays may require the use of an interface bracket for proper installation of the display If an interface bracket is not installed or there are any other questions regarding the installation of the display immediately contact a Chief Customer Service representative by calling 800 582 6480 or by visiting www chiefmfg com WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in face2. INSTALLATION INSTRUCTIONS CH RNS SS e J S Tr vc rg E La Bore Large Flat Panel In Wall Swing Arm Mount CHIEF PNRIW PNRIWU PNRIW PNRIWU DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Loosen Fastener Installation Instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious pers
3. cable channel in top arm See Figure 7 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4 Secure cables to top arm using two cable ties M 5 Repeat steps 1 through 4 for lower arm WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate PNRIW PNRIWU Installation Instructions From Display From Display M x 4 Figure 7 Adjustments TENSION ADJUSTMENTS Pitch Tension Adjustment 1 With display mounted check for desired Pitch tension 3 f required adjust the Centris Select knob right or left until desired Pitch tension is obtained See Figure 8 3 To lock the mount at the desired position tighten the Pitch locking screw See Figure 9 Centris Select NM Pitch Adjustment Knob Locking Screw Figure 9 Roll Tension Adjustment A CAUTION IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening lateral adjustment will cause excessive wear and may distort adjustment componenis 1 Using a 9 16 wrench not provided slightly tighten or loosen lateral Roll tension adjustment nut See Figure 10
4. 2 Mount the display and check for desired roll tension Figure 8 3 Repeat Steps 1 and 2 until desired Roll tension is obtained Installation Instructions PNRIW PNRIWU Socket Head Capscrew Figure 11 4 Using the adjustment wrench L turn adjustment bar K clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension See Figure 12 and See Figure 13 DECREASE Roll Adjustment Nut Figure 10 Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts Capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar K and adjustment wrench L 2 Place adjustment bar K into socket head cap screw located at swing arm pivot point See Figure 11 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE If changing from a smaller display
5. onal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this kit is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 200 Ibs 90 72 kg Hex Head Wrench Zeskantsleutel Cl t te hexagonale Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips lt gt Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Installation Instructions PNRIW PNRIWU TOOLS REQUIRED FOR INSTALLATION AND PARTS 3 16 B 4 2 short SIDES 2 long Pe 5 16 18 x 5 8 5 16 5 16 F 16 G 4 H 1 J 1 3 16 Figure 1 PNRIW PNRIWU Installation Instructions Installation The follo
6. plate To install display 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall See Figure 5 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 5 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and click lock mechanism has engaged See Figure 5 and See Figure 6 Figure 5 PNRIW PNRIWU NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 Remove pin and nuts and move to lower hol A padlock or bolt m a be placed through latch q holes Figure 6 Cable Management CABLE MANAGEMENT WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points 1 Loosen front and rear cable clamps on top arm See Figure 7 2 Thread cable ties M under cable clamps and secure clamps to top arm See Figure 7 3 Route power audio video cables through the
7. to a larger display may be necessary to increase swing arm tension Figure 13 PNRIW PNRIWU Installation Instructions CHIEF 8805 000242 2007 Chief Manufacturing www chiefmfg com 10 07 USA International Europe Asia Pacific TUDU D T U 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 40 2668620 31 0 40 2668615 Room 301 Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA Post Code 518112 PRY Th Ps Z Ed AS see SE SRR A ISO ZO 86 755 8996 9226 8996 9236 8996 9220 86 755 8996 9217 P d 7 d D Bea d a ai A A De Mr Ba Conse
8. wing procedure assumes that a Chief Model PAC501 In Wall accessory has previously been installed following the installation instructions provided with the PAC501 If a PAC501 2 e is not installed or there are any other questions regarding the a installation of this accessory immediately contact a Chief S ay Customer Service representative by calling 800 582 6480 or by visiting www chiefmig com WARNING IMPROPER INSTALLATION CAN LEAD TO AC MOUNT FALLING CAUSING SEVERE PERSONAL INJURY ae OR DAMAGE TO EQUIPMENT DO NOT deviate from installation instructions provided DO NOT substitute hardware 1 Align mounting holes in swing arm UPPER and LOWER nae mounting brackets with four mounting holes in PAC501 p Q Be lt See Figure 2 NO s t D x4 Upper Mounting Bracket Q C x4 Figure 3 ICT TT 2 N ooa j Trim Installation To install optional trim 1 Remove paper covering adhesive and affix three tape squares F to inside lower flange of each trim piece B See Figure 4 2 Orient trim pieces B as shown in figure below See Figure 4 3 Remove paper covering adhesive back from tape squares F on trim and press trim B against inner wall of box See Figure 4
Download Pdf Manuals
Related Search