Chief Manufacturing Plasma Display Electric Pop-Up Lift User's Manual
Contents
1. Figure 3 Back Connection and Power Cord to Control Box Figure 4 Test Wiring Instruction Manual Plasma Display Electric Pop Up Lift PREPARE THE FURNITURE CABINET AND INSTALL THE LIFT Because of the wide variety of possible mounting situations Chief Manufacturing can only provide general guidelines for lift installation Study the following information carefully and adapt it as necessary to fit your specific installation WARNING Be especially aware of the weight of the unit and the potential for personal injury or of damage to the unit if it is not adequately mounted The lift without a projector weighs approximately 150 Ibs 68 kg The General Guidelines below and the information on the following pages cover the most common mounting situa tions General Guidelines e Compare the inside dimensions of the furniture cabinet in which the lift will be installed with the dimensional requirements of your display and any additional space required for your application Allow for movement of the lift and the display Prepare the Furniture Cabinet WARNNG Be aware during the instal lation that this is a motorized device EA and there are pinch points for people and for electrical wiring Keep hands and electrical wiring away from inter nal components of the mechanism 1 Determine size and weight of display to be lifted See Weight Size and Vertical Travel on page 3 for weight limitations 2 Determin2. INSTRUCTION MANUAL Plasma Display Electric Pop Up Lift PUL Your Plasma Display Electric Pop Up Lift is designed for installation in furniture or cabinets Display mounting is made easy using the Q latch mounting system and your PUL provides a smooth quiet and reliable lift for your dis play The versatile Q latch system not only makes mounting safe and easy it makes changing display makes and mod els quick and inexpensive Simply install the PSB mount ing bracket designed specifically for the display and mount it on the PUL Superior performance and dependability are designed into your PUL The lift is made using heavy duty steel and alu minum extrusion construction All electrical components are UL TUV listed and the use of low voltage solid state circuitry controls ensure safety and reliability BEFORE YOU BEGIN CAUTION To prevent damage to the PUL which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install or operate the unit Pay particular atten tion to the Important Precautions on Page 1 If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 CHIEF MANUFACTURING INC NI 1 800 582 6480 952 894 6280 FAX 952 894 6918 2000 Chief Manufacturing Y 8401 EAGLE CREEK PARKWAY STE 700 SAVAGE MINNESOTA 55378 USA Ideas Supporting Ideas PART NO 8805 000009 Rev C www c
3. 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm PUL4233 44 125 to 56 125 42 125 to 54 125 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm PUL4239 44 125 to 56 125 42 125 to 54 125 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm PUL4245 44 125 to 56 125 42 125 to 54 125 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm PUL4251 44 125 to 56 125 42 125 to 54 125 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm PUL4257 44 125 to 56 125 42 125 to 54 125 1120 8mm to 1425 6mm 1070 0mm to 1374 8mm Instruction Manual Plasma Display Electric Pop Up Lift DIMENSIONAL DRAWING See Table 1 on page 3 for outside adjustable width dimension H and dimension W Front View Side View 4 MIN 11 MAX ADJUSTMENT 2 459 Top View A Instruction Manual Plasma Display Electric Pop Up Lift INSPECT AND TEST THE UNIT BEFORE INSTALLING Inspect The Unit 1 Carefully inspect the Plasma Display Electric Pop Up Lift PUL for shipping damage If any damage is apparent call your carrier claims agent and do not continue with the installa tion until the carrier has reviewed the damage NOTE Read all assembly instructions before starting assem bly Carefully inspect PUL components for damage checking verti cal extrusion arms to make sure they are parallel IMPORTANT Before mounting the lift in the furniture cabinet make the following tests to be sure that it operates properly and ha
4. e Allen wrench set NOTE Other tools may be required depending on the method of installation WEIGHT SIZE AND VERTICAL TRAVEL SPECIFICATIONS See Table 1 on page 3 for the weight size and vertical travel specifications of your specific model 1 Determine size and weight of the equipment to be lifted 2 Determine the vertical travel height required for presentation viewing Instruction Manual CONTENTS WEIGHT SIZE AND VERTICAL TRAVEL SPECIFICATIONS coccoccccccccicncnnncc nnanns 3 DIMENSIONAL DRAWING oeer 4 INSPECT AND TEST THE UNIT BEFORE INSTALLING coccccocccconnnononononancnnnnnnninn 5 Inspect The Unit omic rasca 5 Test The Unit titi 5 PREPARE THE FURNITURE CABINET AND INSTALL THE LIFT coooococcoccnincnacnnonnncnnnanns 6 General Guidelines siiiniioriiin ici dicids 6 Prepare the Furniture Cabinet oocoonnoccnnoccccnonncnnns 6 Furniture Opening Finish Piece Options 6 Extended Position Finish Piece Option 6 Retracted Position Finish Piece Option 7 Install the PUL into the Cabinet ee 9 INSTALL THE DISPLAY ON THE LIFT 10 Attach Brackets to the Display 0 0 eee 10 Mount the Display dt 10 ADJUSTMENTS 0 11 Width Adjustment ED 11 Adjust Vertical Travel iii ii 11 WIRING ii ol 13 P shb tton idas 13 Extend and Retract Terminals to beTriggered by Separate Dry Contacts unir 13 Remote RETO is 15 12 Volt Out Supply sssssicininisicnaii tintas ios 17
5. obtain the five longer 3 8 16 capscrews for assembly with backing 5 Place the finish piece on the shelf making sure it is correctly positioned to allow clearance when lowered and transfer the i pattern of the five access holes onto the finish piece pers alee 8 6 Drill five through holes with clearance for 3 8 bolts in the finish piece and any cord management holes that may be nec essary 7 Place the finish piece on the shelf 8 Place the plasma mounting assembly on top of the finish piece see Figure 5 9 Using a 5 16 Allen wrench inserted through the five access Figure 5 Plasma Mounting Assembly holes on the bottom of the shelf see Figure 6 install five longer 3 8 16 cap screws 10 With the aid of another person lift the display up to the mount aligning the PSB mounting buttons on the display with the teardrop slots on the mount set the plasma into place and adjust mounting assembly to ensure proper clearance is achieved TNA ES 11 Measure and record clearance dimensions and with the aid of another person remove plasma WARNNG Be aware during the installa tion that this is a motorized device and RA there are pinch points for people and for electrical wiring Keep hands and electri NN cal wiring away from internal components of the mechanism 12 Carefully without plasma mounted on lift operate lift to Figure 6 Access Holes ensure finish piece has sufficient clearance during ful
6. 24 Volt Out Supply scan nia test scacsesened aid 17 Two Dry Contact Closures coooccnconnonnnocnnocnnonncnns 17 Low Voltage Sensing uri ii a 17 TROUBLESHOOTING ooncocococcocncncnnnnnnononannananiacanans 19 Plasma Display Electric Pop Up Lift Instruction Manual 3 Determine the inside dimensions available in your furniture cabinet see Table 2 Adjustable Width Plasma Display Electric Pop Up Lift Table 1 Weight Size and Vertical Travel Lift Outside Max Equipment Size Vertical Model Capacity Dimensions HxWxD Travel 230Lbs 33 75 x7 7 25 5 x54 125 x6 5 28 PUL4228 104 3Kgs 857 3mmx195 6mm 647 7mmx1374 8mmx165 1mm 711 2mm PUL4233 230Lbs 38 75x7 T 30 5 x54 125 x6 5 33 104 3Kgs 984 3mmx195 6mm 774 7mmx1374 8mmx165 1mm 838 2mm PUL4239 230Lbs 44 75 x7 7 36 5 x54 125 x6 5 39 104 3Kgs 1136 7mmx195 6mm 927 1mmx1374 8mmx165 1mm 990 6mm PUL4245 230Lbs 50 75 x7 T 42 5 x54 125 x6 5 45 104 3Kgs 1289 1mmx195 6mm 1079 5mmx1374 8mmx165 1mm 1143 0mm PUL4251 230Lbs 56 75 x7 7 48 5 x54 125 x6 5 51 104 3Kgs 1441 5mmx195 6mm 1231 9mmx1374 8mmx165 1mm 1295 4mm PUL4257 230Lbs 62 75 x71 T 54 5 x54 125 x6 5 57 104 3Kgs 1593 9mmx195 6mm 1384 3mmx1374 8mmx165 1mm 1447 8mm Table 2 Adjustable Width Model Outside Inside E 44 125 to 56 125 42 125 to 54 125 Bree
7. e pinch points for MA people and for electrical wiring Width Adjustment Adjust width as follows see Figure 14 1 Loosen the six 5 16 18X5 8 hex head bolts on the front of each half of the motor control box and eight 1 4 20 socket head Allen screws 4 front and 4 back on the bracket mounting crossbrace 2 Slide the halves of the lift to the disired width and secure by tightening the bolts and socket head Allen screws loosened in Step 1 Adjust Vertical Travel WARNING Be aware during the installation that this is a motorized device and there are pinch points for UN people and for electrical wiring CAUTION Vertical travel adjustment must always be made with the shelf in the middle of travel position and the power switch OFF There are two knobs for setting the travel limits which are located at one end of the base controller housing see Figure 15 The knob closest to the outside is the down stop limit adjustment The knob closest to the center is the up stop limit adjustment 1 With the shelf in the middle of travel position and the power switch OFF adjust the down limit to the desired height by turn ing the down stop adjustment knob clockwise higher posi tion counterclockwise lower position CAUTION The unit must always be able to reach its own limit switches and turn itself off 2 Check to be sure the limit switch stops the unit and the unit is not being stopped due to interference 3 Wit
8. e vertical travel height required for presentation viewing See Table 1 for height limitations Furniture Opening Finish Piece Options Because of the wide variety of possible mounting sit uations Chief Manufacturing can only provide gen eral guidelines for finish options Study the following information carefully and adapt it as necessary to fit your specific installation NOTE Always leave access to the lift for maintenance pur poses Extended Position Finish Piece Option A finish piece covering the opening when the unit is in the fully extended position may be installed for estetic purposes Using the material cut slight smaller than the opening size install the finish piece as fol lows 1 Measure the width of the finish piece 2 Measure the distance between the verticle extrusion arms and subtract a nominal amount for clearance CAUTION Failure to allow clearance for the finish piece to retract to the fully lowered position may result in damage to the fin ish piece damage to the lift and damage to the plasma Instruction Manual Plasma Display Electric Pop Up Lift 3 Make sure the finish piece measured in step 1 is smaller than the clearance distance measured in step 2 and note any cord management access holes that may be necessary 4 Measure the thickness of the finish piece add this thickness to the length of the five capscrews used to secure the plasma mounting assembly when a backing is not used and
9. ectric Pop Up Lift THIS PAGE INTENTIONALLY BLANK 14 Instruction Manual Plasma Display Electric Pop Up Lift Remote RC 10 RC 10 Controller en Circuit Board Box Assembly Y 1 thru 10 gt 1 thru 20 gt RC 10 Remote Figure 21 Contacts Connecti Wire for remote RC 10 operation as follows see Figure 21 1 Install a jumper wire between terminals 6 and terminal 2 see Figure 22 1 thru 10 gt 2 Connect the white wire of the RC 10 controller unit to terminal 1 see Figure 23 11 thru 20 gt 11 12 13 14 15 16 17 18 19 20 REEERE 3 Connect the red wire of the RC 10 controller unit to terminal 2 4 Connect the black wire of the RC 10 controller unit to Figure 22 Contacts Connection terminal 5 5 Connect the power source to the lift EE y Black lead _ ID NOTE If the unit does not activate check to make sure the 9 volt battery is working and make sure the dip switches in the send ing unit match the dip switch settings in the controller unit see Figure 24 rer UL Figure 24 Dip Switches 15 Instruction Manual Plasma Display Electric Pop Up Lift THIS PAGE INTENTIONALLY BLANK Instruction Manual Plasma Display Electric Pop Up Lift 12 Volt Out Supply This internal power supply can be used to power external devices amp or to initiate specific functions see Pushbutton operation and Figure 25 1 Connect one lead to 12 VOLT GROUND terminal 9 2 C
10. f the inside enclosure where the lift will be mounted d Adjust the width of the lift allowing for clearance and hand tighten all bolts loosened in step a NOTE The unit must be installed square and parallel in ALL dimensions for smooth and reliable operation The extrusions housing the chains must also remain exactly square to the power box and parallel to each other after it has been installed Shims may be required between the unit and the enclosure to maintain parallel dimensions between the extrusions Place the unit into the enclosure so the load to be lifted is cen tered over the vertical extrusion beams With the lift in place use the base of the lift mechanism as a template to transfer 4 holes 17 64 diameter to the enclosure bottom NOTE If desired you can use the additional four holes in the cor ners of the lift but you must fill the space between the lift and enclosure bottom to prevent warping 4 5 Remove the lift mechanism from the enclosure Drill the 4 holes 17 64 diameter in the bottom of the enclo sure Place the unit into the enclosure so the holes in the mechanism line up with the holes in the enclosure Secure the unit into the enclosure using 4 thru bolts 1 4 20 or larger 8 fender washers and 4 Nyloc nuts see Figure 10 Tighten securely Fight 1 4 20 Socket ead AllenScrews Bracket Mounting Crossbrace Six Hex Head Bolts Motor Control Box Figure 9 Motor Control B
11. g the installation that this is a motorized device and there are pinch points for people and for electrical wiring Keep hands and electrical wiring away from internal components of the mechanism CAUTION Failure to allow clearance for the finish pieces to retract to the fully lowered position may result in damage to the finish pieces damage to the Ea lift and damage to the plasma 10 Carefully without plasma mounted on EN lift operate lift to ensure the finish pieces have sufficient clearance during full travel and that top finish piece is flush with the furniture top when fully retracted Retracted Position Backing Finish Piece Side Pieces ao Plasma Extendeded Position Finish Piece Figure 7 Retracted Position Finish Piece Y 1 inish Piece TER Furniture Figure 8 Side Piece Dimensions Instruction Manual Plasma Display Electric Pop Up Lift Install the PUL into the Cabinet 1 Adjust motor control box unit see Figure 9 NOTE The motor control box unit is factory set to the nar rowest horizontal position a Loosen the six 5 16 18X5 8 hex head bolts on the front of each half of the motor control box and eight 1 4 20 socket head allen screws 4 front and 4 back on the bracket mounting crossbrace Slide both halves of the lift all the way in and out to ensure the lift can be adjusted freely c Measure the width o
12. h the shelf in the middle of travel position and the power switch OFF adjust the up limit to the desired height by turning the down stop adjustment knob clockwise higher position counterclockwise lower position Eight 1 4 20 Socket Head AllenScrews Bracket Mounting Crossbrace Motor Control Box Six Hex Head Bolts Figure 14 Width Adjustmentr Control Knob Retract stop limit Extend stop limit VERTICAL EXTRUSION BEAM Travel Control Knobs Retract Stop Limit Extend Stop Limit BASE HS6 Figure 15 Vertical Travel Adjustment 11 Instruction Manual Plasma Display Electric Pop Up Lift THIS PAGE INTENTIONALLY BLANK 12 Instruction Manual Plasma Display Electric Pop Up Lift WIRING EXAMPLES The information on the following pages cover the most common wiring options Pushbutton e Extend and Retract Terminals to be Triggered By Separate Dry Contacts e Remote RC 10 e 12 Volt out supply e 24 Volt out supply e Two dry contact closures e Voltage Sensing Pushbutton Wire for pushbutton operation as follows 1 Install a wire between terminal 5 extend retract common and ground terminal 3 see Figure 16 2 Connect one wire from pushbutton to terminal 4 12 VDC power supply and the other wire from the pushbut ton to terminal 6 extend retract see Figure 17 With the unit plugged in push the button once and the unit should extend Push the button during trave
13. hiefmfg com 05 05 Instruction Manual Plasma Display Electric Pop Up Lift A IMPORTANT WARNINGS and CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre sponding instructions WARNING Be aware during the installation that this is a motorized device and there are pinch points for people and for electrical wiring WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted The lift without a projector weighs approximately 150 Ibs 68 kg WARNING Be sure the lift is installed square and parallel in all dimensions to avoid damage to the lift Avoid stress ing the unit at any time during installation WARNING Electrical outlets must be installed by a qualified electrician Follow all electrical codes e CAUTION Vertical travel adjustment must always be made with the shelf in the middle of travel position and the power switch OFF e CAUTION The unit must always be able to reach its own limit switches and turn itself off e CAUTION Test the unit for shipping damage See Inspect and Test the unit before installing on page 5 TOOLS REQUIRED FOR INSTALLATION e Phillips screwdrivers No 1 and No 2 e Electric drill and 17 64 drill bit e Socket set with extension
14. l and the unit will stop at that location Push the button after the unit is extended or stopped in mid travel and the unit will retract Extend and Retract Terminals to be Triggered By Separate Dry Contacts These terminals can be used with a wall switch or a separate set of dry contacts for dedicated extend and dedicated retract Momentary contacts are preferable NOTE The connection between the ground 13 and any other terminal connection must be broken open before completing the next circuit 1 Connect the common to terminal 13 see Figure 18 2 Connect the extend to terminal 11 see Figure 19 3 Connect the retract to terminal 12 see Figure 20 Completing the circuit between terminal 13 and terminal 11 will cause the unit to extend to the show position see Adjust Vertical Travel on page 11 to change height setting Completing the cir cuit between terminal 13 and terminal 12 will cause the unit to retract to the closed position 234567 89 108 i 1 thru 10 gt 11 thru 20 gt 1 thru 10 gt 11 thru 20 gt Figure 17 Pushbutton Wires 1 thru 10 gt 11 thru 20 gt Morsa 20 Common WM f Figure 18 Common for Extend and Retract Contacts Ltnru Lu 1 thru 20 gt Extend Figure 19 Extend Contact Wiring M YA E LS OD L thru 10 gt 1 thru 20 gt Retract Figure 20 Retract Contact Wiring 13 Instruction Manual Plasma Display El
15. l travel Retracted Position Finish Piece Option A finish piece covering the opening when the unit is retracted may be installed for estetic purposes Install the finish piece as follows 1 Complete the instructions in Extended Position Finish Piece Option on page 6 2 Cut two side pieces matching the width of the extended posi tion finish piece to a length slightly longer than the distance the plasma will travel this will be trimmed later 3 Cuta top piece matching the dimensions of your extended position finish piece see Figure 7 Instruction Manual Plasma Display Electric Pop Up Lift 4 With the extended position finish piece and the plasma mounted lower the unit to its fully retracted position 5 Place the side pieces in position do not attach 6 Place the top piece in position do not attach 7 Measure the distance from the top surface of the top piece to the top surface of your furniture and cut this dimension from each side piece see Figure 8 8 Remove and assemble finish pieces bottom sides and top making sure your finished box is square CAUTION A backing is recommended for support Frame move ment could result in damage to the frame damage to the lift and damage to the plasma CAUTION Check plasma ventilation requirements Provide ven tillation for your application 9 Measure box construct a backing for lateral support and install backing WARNNG Be aware durin
16. n Manual Plasma Display Electric Pop Up Lift TERMINAL FUNCTION DEFINITIONS TERMINAL TERMINAL FUNCTION DESCRIPTION WIRING OPTIONS NOTES This is an internal power supply for 1 24 VOLT AC 24 volt AC output powering external devices amp Remote Controllers Chief Mfg offers the RC 10 Radio 24 VOLT AC Frequency Remote Controller which runs 2 COMMON AOS icommon off of this power supply 3 GROUND Ground This is an internal power supply for powering external devices amp or used for initiating specific functions 4 12 VOLT DC 12 volt DC Extend Retract 5 or Voltage Sensor 7 Initiates movement if lift is static or To Operate using Internal Power Function operates on momentary switch 5 EXTEND stops movement if lift is in motion Source only RETRACT Direction of travel will be opposite Connect terminals 3 amp 6 with of last direction of travel Jumper Wire Connect Operating range is 5 30 Volts AC or DC Momentary Switch to terminal 4 Connect other line of Momentary Switch to terminal 5 EXTEND d e To Operate using External Power NOT TO BE USED AS GROUND FOR 6 RETRACT tem l toi E i Source FUNCTION OTHER THAN COMMON E A cence Muna Connect External Power Supply s EXTEND RETRACT TERMINAL 5 movement 3 Common to terminal 6 Connect initiating signal to terminal 5 When terminal senses voltage unit Voltage Sensing will extend Connect positive lead to termi
17. nal 7 VOLTAGE 7 Connect Ground of switching Operating range is 5 30 Volts AC or DC SENSOR When terminal senses cessation of device to terminal 8 voltage unit will retract Single Pull Throw Latching Switch Connect terminals 3 amp 8 with NOT TO BE USED AS GROUND FOR VOLTAGE Used in conjunction with Voltage Jumper Wire Connect first FUNCTION OTHER THAN VOLTAGE 8 SENSOR Sensor when using an external Switch Terminal to terminal 4 SENSOR TERMINAL 7 COMMON power source to initiate movement Connect other Switch Terminal to terminal 7 Extends unit to maximum limit Feature not available on all models SERVICE bypassing notuidlcuse el setting Momentary or Latching contact to 9 7 If using Latching Switch be sure to EXTEND bad 4 Ground terminals 3 10 13 or 20 i A Often used for servicing projectors disengage Switch prior to initiating any in ceiling lifts on PCL and MD other function models 10 GROUND Ground 20 Instruction Manual Plasma Display Electric Pop Up Lift Extends unit to preset travel limit If using Latching Switch be sure to 11 EXTEND Customer within a preset aie disengage Switch prior to initiating any na other function range may adjust travel limits Momentary or Latching contact to Retracts unit to preset travel limit round terminals 3 10213 0120 If using Latching Switch be sure to 12 RETRACT Travel limits may be adjusted by disengage Switch
18. onnect one lead to 12 VOLTS OUT terminal 10 24 Volt Out Supply This internal power supply can be used to power external devices amp remote controllers see Figure 26 1 Connect one lead to 24 VOLT COMMON terminal 2 2 Connect one lead to 24 VOLTS OUT terminal 1 Two Dry Contact Closures NOTE Dry contacts are rated for 1 Amp 24 volts These contacts can be used to complete circuits to external devices see Figure 27 and Figure 28 1 Connect one lead to terminal 17 extend limit common 2 Connect one lead to terminal 16 closes when unit reaches full extension 3 Connect one lead to terminal 19 retract limit common 4 Connect one lead to terminal 18 closes when unit is fully retracted Low Voltage Sensing 1 Connect positive lead 5 30 volts AC DC to terminal 7 and ground of switching device to terminal 8 see Figure 29 Unit extends when voltage is sensed retracts when voltage ceases Example using internal 12 volt DC supply Figure 30 Figure 30 12 Volt DC Supply 111213 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 00 ba al 1 1 thru 10 gt 11 thru 20 gt pi 1213 44 5 46 17 18 19 20 EEEREN Figure 29 Low Voltage Sensing Instruction Manual Plasma Display Electric Pop Up Lift THIS PAGE INTENTIONALLY BLANK 18 Instruction Manual Plasma Display Electric Pop Up Lift TROUBLESHOOTING If the lift is installed according to the
19. ox Optional holes requiring spacers between the lift and the bottom of the enclosure Thru Bolt two fender washers and Nyloc Nut two places each side Figure 10 Secure Lift Instruction Manual Plasma Display Electric Pop Up Lift INSTALL THE DISPLAY ON THE LIFT Attach Brackets to the Display 1 Follow the instructions accompanying the PSB brackets designed for your display Remove screws Mount the Display 1 Remove 4 screws and slide back panel cover up and out see Figure 11 2 Make sure the latch on the mount is lowered to the side before attempting to place the display on the mount see Figure 12 3 With the aid of another person lift the display up to the mount aligning the PSB mounting buttons on the display with the teardrop slots on the mount and set the plasma into place Figure 11 Back Panel Cover Removal CAUTION If the latch does not travel to the full upright position remove and reset the display Latch Lowered 4 While supporting the display raise the latch Raise Latch to Secure Display 5 Install Q clamp see Figure 13 6 Install back panel cover and secure using 4 screws LA Tear Drop Slots y Figure 12 Latch and Tear Drop Slots Q clamp Figure 13 Install Q clamp 10 Instruction Manual Plasma Display Electric Pop Up Lift ADJUSTMENTS WARNING Be aware during the installation that this is a motorized device and there ar
20. prior to initiating any customer within a preset maximum other function range 13 GROUND Ground EXTEND Immediately reverses direction of Chief Mfg offers the SS 10 Pressure 14 ERROR travel when triggered while unit is Sensitive Safety Strip to provide this extending function Momentary contact to Ground Please specify hu inch ired terminals 3 10 13 or 20 ease specify how many inches requir Immediately reverses direction of spanning entire pinch zone 15 RETRACT travel bei d whileunit is The SS 10 must be ordered with the ST 1 ERROR avel when triggered while unit is Terminals retracting EXTEND 16 LIMIT RELAY ease teen RATED FOR 1 AMP 24 VOLTS EXTEND j LIMIT 17 RELAY COMMON RETRACT 18 LIMIT RELAY Closes set of internal dry contacts RATED FOR 1 AMP 24 VOLTS RETRACT when unit reaches full retraction LIMIT 19 RELAY COMMON 20 GROUND Ground WIRING THE RC 10 Connect white lead to terminal 1 red lead to terminal 2 and black lead to terminal 5 Place jumper wire from terminal 2 to terminal 6 WIRING A MOMENTARY PUSH BUTTON Connect terminals 3 amp 6 with Jumper Wire Connect Momentary Switch to terminal 4 Connect other line of Momentary Switch to terminal 5 21
21. s not been damaged in shipping Test The Unit 1 2 Set the PUL on a clean level surface Connect the motor control box to the control circuit housing see Figure 1 Figure 2 and Figure 3 Install two terminal blocks in control box see Figure 2 NOTE The lift is supplied with a momentary push button on the end of a cable to help you pretest the operation Connect the momentary push button provided cable leads to terminals 6 and 1 and add a jumper wire provided electri cal wire about 4 in long with 1 4 in stripped at each end between terminals 2 and 5 on the same terminal block see Fig 4 Plug the lift s power cord see Figure 3 into a 110V 60 Hz or 220V 50 Hz as appropriate 15 amp outlet NOTE The lift draws approximately 1 5 amps WARNNG Be aware during the installation that this is a motorized device and there are pinch points for people and for electrical wiring Keep hands and electrical wiring NN away from internal components of the mechanism Operate the lift much like a garage door opener press the but ton when the lift is at its bottom position and it will move up press again when it is at its top position and it will move down press while moving and it will stop Use the push button to check that the lift runs to the top and bottom of its travel without any interference that might indicate damage during shipment Unplug the lift s power cord
22. se instructions it should operate trouble free indefinitely If you do encounter a problem and it isn t covered by the troubleshooting suggestions below call the Technical Services Department at Chief Manufacturing 1 800 582 6480 952 894 6280 Possible Symptons Causes Suggested Action No Movement and No No Power 1 Check power to unit supply cord activation Sound control and connections No power Provide power repair cord tighten connections or repair activation control Power Check fuse on circuit board If fuse is OK proceed to next step Faulty Circuit Board 2 Check circuit board as follows Make three jumper wires with ends stripped Install one jumper wire on terminal 11 Install one jumper wire on terminal 12 Install one jumper wire on terminal 13 Momentarily touch jumper wire from terminal 11 to terminal 13 Unit should extend Momentarily touch jumper wire from terminal 12 to terminal 13 Unit should retract Activates In both Directions Circuit board OK faulty activation interface Check remote switch circuit or batteries in remote control Unit Fails Both Either Direction Call Chief Manufacturing Unit Operates Noisily Track Misalignment 1 Check for noise and or metal shavings in track Squeeling or grinding Noise or Shavings Check and adjust track and or shelf as necessary No Track Noise Possible brake problem call Chief Manufacturing Instructio
Download Pdf Manuals
Related Search