Chief Manufacturing KWK-110 User's Manual
Contents
1. It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the KWK 110 mount up to and including the keyboard does not exceed 10 Ibs 4 5 kg 7 73 6 50 DISTANCE TO THE CENTER OF THE COMPONENT MOUNTING BRACKET 5 99 KEYBOARD DEPTH gt 6 50 SWING OUT MOUSE TRAY r KEYBOARD TRAY em E 180 PIVOTPOINTS O l 18 75 1 30 a La o COLLAPSED EXTENDED WRIST PAD 6 50 10 02 REMOVABLE FOR Lu DEEPER KEYBOARDS SWING OUT MOUSE TRAY E MAX 29 15 A 6 50 m 3 33 COLLAPSED Installation Instructions KWK 110 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestig2. A Hh ne A RN BE REER AB DRAF 86 755 8996 9226 86 755 8996 9217
3. Figure 1 3 Install two 10 x 2 1 2 Phillips Pan Head Tapping screws H through 10 washers J wall plate C and drywall into wood stud See Figure 1 4 Ensure wall plate C is vertical then tighten screws H A CAUTION Overtightening screws may cause wall bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in later step Figure 3 5 Insert top of wall mount A over lip on top of wall plate C See Figure 2 6 Swing wall mount down flush against wall See Figure 2 KWK 110 Installation Instructions CABLE MANAGEMENT 1 Thread keyboard cable through one of two holes along the KEYBOARD AND WRIST PAD INSTALLATION hack edae of the keyboard trey 1 Remove adhesive backing from one side of hook and loop 2 connectors F Open the cable management bracket by sliding it towards the edge of the arm See Figure 6 2 Place hook and loop connectors F on bottom of the keyboard and Gem of wrist E as shown NOTE If necessary cable management bracket attach screws See Figure 4 may be loosened using hex key L NOTE Place connectors only on flat sections of the keyboard to ensure that they stick to the surface 3 Remove the adhesive backing from the other side of the hook and loop connectors F 4 Firmly place keyboard on keyboard tray making sure to Attach leave room for the wrist pad if nec
4. INSTALLATION INSTRUCTIONS Height Adjustable Dual Arm with Keyboard Tray CHIEF KWK 110 Our Mounts Your Vision KWK 110 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions DIMENSIONS CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty
5. essary See Figure 4 d Screws 5 Firmly place wrist pad D on keyboard tray in front of the keyboard See Figure 4 Sai keyboard F x6 OPEN Position CLOSED Position H View from Bottom Figure 6 CAUTION Ensure that adequate cable slack exists for movement of keyboard and mouse and that cables will not be pinched when bracket is closed 3 Carefully insert cables into bracket See Figure 7 Figure 4 Mouse Holder Installation 1 Remove adhesive backing from mouse holder E 2 Place mouse holder E on wall at desired location See Cable Management Figure 5 Bracket in open position Cable Path typical Figure 7 4 Close cable management bracket by sliding it back towards the centerline of the arm NOTE If necessary cable management bracket attach screws may be tightened using hex key L 5 Carefully insert cables in cavity located in lower portion of mount arm See Figure 8 6 Using Phillips screwdriver install cover B with two 8 32 x 3 8 Phillips flat screws G See Figure 8 Figure 5 Installation Instructions KWK 110 Cable Path typical Height Adjustable Screw Figure 8 ADJUSTMENTS Swing Arm Pivot Swing 1 Using 3 16 hex key L slightly loosen or tighten the adjustment screw s as necessary See Figure 9 Pivot Swi
6. ing vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster e 4 y E Gi Open Ended Wrench Llave de boca Quitar Gabelschlissel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Cl a fourche Retirez By Hand Optional A mano Opcional Von Hand Optional Com a mao Opcional A mano Opzionale Met de hand Optie la main En option d K Hex Head Wrench Llave de cabeza hexagonal sch O Sechskantschlussel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Security Wrench Lla
7. ng Adjustment Screws d Log Adjustable Mouse Trays Figure 9 Mouse Tray Adjustment 1 Mouse trays slide open and closed on both sides of the tray for both right handed and left handed users See Figure 9 Height Adjustable 1 Using 5 32 hex key M slightly loosen or tighten the adjustment screw as necessary See Figure 10 e If display settles on its own rotate adjustment screw counterclockwise towards the symbol e If display rises on its own rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw Figure 10 Tray Tension Adjustment 1 Using 1 4 hex key K slightly loosen or tighten the tray tension adjustment screw as necessary See Figure 11 5S Tray Tension Adjustment Figure 11 KWK 110 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a division of Milestone AV Technologies 8834 000005 2008 Milestone AV Technologies www chiefmfg com 10 08 USA International Europe Asia Pacific A P F A P F A 37r JR P F 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHIN
8. ve de seguridad Sicherheitsschlussel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit KWK 110 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1 4 auer aa included included included P R ES Gm X E 1 F6 G 2 H 2 J 2 8 32 x 3 8 10 x 2 1 2 10 S a ku gt Lit M t ae 3 16 5 32 Installation Instructions KWK 110 MOUNT INSTALLATION WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS MOUNT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of the mount and all equipment attached to it Reinforce the structure as required before installing the mount Mount Installation Using Wood Studs 1 Determine location for mount keeping in mind extension and height adjustment if applicable requirements 2 Using wall plate C as a template mark then drill two 1 8 diameter pilot holes through top and bottom holes of wall bracket into wall structure See Figure 1 o wx DOC Figure 2 7 Use 5 32 hex driver to tighten set screw in bottom of wall mount See Figure 3 NOTE Ensure set screw engages on back side of wall plate to properly secure wall mount
Download Pdf Manuals
Related Search