Chief Manufacturing KSA-1020 User's Manual
Contents
1. Figure 1 CPU Installation 1 Release bracket from mount by moving the flag to the open position See Figure 2 2 Remove bracket from mounting buttons on back of mount See Figure 2 t lt lt C Figure 4 5 Loosen adjustment knobs on top and bottom of the mount and slide flanges in order to allow for the CPU to be inserted for mounting See Figure 5 Figure 2 NOTE Top and bottom knobs can be removed and inserted into the front square holes in order to allow for large 3 If hanging mount underneath desk remove mounting KSA 1020 Installation Instructions CPU s to be installed See Figure 5 NOTE Flanges may be reversed in order to allow for narrow CPU s to be installed in a secure manner If this is done be sure to also to remove and reinstall strap so that the buckle is facing out for easy adjustment Figure 5 6 Set CPU within mount A See Figure 6 7 Use adjustment knobs to compress mount around CPU until CPU is tightly secured within mount A See Figure 6 4 A NS Figure 6 8 Tighten front strap to desired tension WALL MOUNT INSTALLATION WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS MOUNT CAN RESULT IN2. Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions KSA 1020 TOOLS REQUIRED FOR INSTALLATION z E 2 1 4 20 X 1 3 4 j F 1 F i G 2 3 8 X 1 1 4 12 X 2 1 2 Installation Instructions KSA 1020 ASSEMBLY AND INSTALLATION buttons to reinstall them in the holes in which they will be used Installation of Protective Rubber Edging f mounting vertically move mounting buttons in 1 Place four strips of protective rubber edging C over the the four holes on top of the mount See Figure 3 sharp edges located on the top and bottom of the mount A If mounting horizontally move mounting buttons See Figure 1 in the top four holes on the back See Figure 3 Vertical button location Horizontal button location Figure 3 4 Loosen adjustment knob at the back of the mounting unit and adjust height of mount to a height greater than the height of the CPU to be installed Loosen strap at the front of the mount if necessary See Figure 4
3. INSTALLATION INSTRUCTIONS Wall and Desk CPU Mount CHIEF KSA 1020 Our Mounts Your Vision KSA 1020 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions DIMENSIONS CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury dama
4. SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of the mount and all equipment attached to it Reinforce the structure as required before installing the mount NOTE Mount may be installed using wood studs steel studs or it may be installed directly into drywall For steel stud and drywall installation proceed ahead to Site Requirements for Using Steel Studs section For desk mounting proceed ahead to Desk Mounting Installation section Mount Installation Using Wood Studs 1 Determine location for mount keeping in mind CPU size and safety requirements 2 Using the removed mounting bracket as a template mark and then drill two 7 64 diameter pilot holes through top and bottom holes of wall bracket into wall structure See Figure 7 DOC mounting bracket Figure 7 3 Install two 12 x 2 1 2 round Phillips wood screws G through bracket and drywall into wood stud See Figure 7 4 Ensure bracket is vertical then tighten screws G NOTE Proceed ahead to Mounting CPU to Wall section to complete installation Installation Instructions KSA 1020 Site Requirements for Using Steel Studs WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENTI The figure below identifies the minimum requireme
5. e fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl a fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand Ala main Optional Opcional Optional Opcional Opzionale Optie En option d y S V 2 Hex Head Wrench Llave de cabeza hexagonal d GI CG
6. ge to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 40 Ibs 18 1 kg 360 SWIVEL CAPABILITY UNDER DESK MOUNTED C ONFIGURATION 37 1 46 MOUNTING SURFACE TO CPU SURFACE WALL MOUNTED CONFIGURATION O 191 g D TO CPU SURFACE 0 7 50 WIDTH OF CPU RANGE 38 z 1 50 MOUNTING SURFACE 248 457 9 75 18 00 HEIGHT OF CPURANGE 109 __ 4 29 r TES z I W PB MOUNTING o Ve HOLES TY 9 Installation Instructions KSA 1020 LEGEND Tighten Fastener Apretar elemento d
7. ng a stud finder or similar method locate stud Align mounting holes in mount with stud making sure mounting holes are centered on stud See Figure 9 WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENTI Mart location of two mounting holes on wall using the wall plate as a template Mark holes vvhere the top and bottom holes of the bracket will be connected See Figure 9 Drill two 1 2 holes See Figure 9 o o 1 2 x2 Mounting holes centered on stud 6 Figure 9 Hold metal channel on anchor B flat alongside plastic straps and slide channel through hole See Figure 10 Drywall Plastic Se vo Figure 10 Holding plastic straps on anchor B pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud See Figure 11 Slide plastic cap on anchor B towards wall until flange of cap is flush with wall See Figure 11 Plastic Cap Steel Stud Drywall 10 11 12 13 Anchor Metal Channel Side View Figure 11 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 12 Repeat steps 6 through 9 for remaining mounting hole Steel Stud Drywall Plastic Cap Plastic St
8. nts for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs Mount Installation Location Must be centered on stud to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center N D I gt SOL S PS es Drywall li JS Sk Se DN SN Cen be 1 2 RQ minimum Drywall SEN Thickness Both Sides of Stud See Hazard statement on page 2 If back side of wall is unfinished drywall must be installed SS NN ANON N N SCH SS AS WON SH N N Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 962 S 125 18 C Shaped S Stud Section There must be a minimum of 1 7 8 48mm clearance inside wall Figure 8 KSA 1020 Installation Instructions Wall Mounting Using Steel Studs or Drywall After determining the site meets the installation requirements 1 2 3 4 5 Identify desired mounting location on wall Usi
9. ogies 8834 000003 2008 Milestone AV Technologies www chiefmfg com 10 08 USA International Europe Asia Pacific A P F A P F A ZB JAR P F 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang Buji Town Shenzhen CHINA 3Jl rh ne PRA A R RES ES A IB DRAF 86 755 8996 9226 86 755 8996 9217
10. raps Anchor Metal Channel SIDE VIEW Figure 12 Place mounting bracket over anchors and align mounting holes in display mount with holes in anchors See Figure 13 Insert 1 4 20 x 1 3 4 Phillips pan head screw E into mounting hole on mounting bracket and into anchor B and tighten until flush against mounting bracket DO NOT overtighten See Figure 13 Repeat steps 11 through 13 for remaining mounting hole Installation Instructions KSA 1020 Steel Stud Drywall AN GC E x 2 TIN 7 Mounting Bracket Anchor Metal Channel SIDE VIEW Figure 13 Mounting CPU to Wall AA CAUTION Overtightening screws may cause wall bracket to compress into soft wall surface resulting in difficult mount installation 1 Ensure bracket flag is in the open position See Figure 2 2 Insert mounting buttons into the four large mounting holes on the bracket See Figure Flag in closed position Figure 14 3 Move flag to closed position in order to fully secure mount to bracket See Figure 15 Figure 15 Desk Mount Installation WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the desk to which this component i
11. s attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component NOTE The following instructions are for mounting with full 360 swivel capability for easy cord access If this capability is not desired connect mounting bracket using two screws as demonstrated in the wall mounting instructions Determine location for mount keeping in mind CPU size and safety requirements Using bracket and bearing D as a template mark and drill one 17 64 diameter pilot hole through underside of desk at desired mounting location Ensure entire mount will clear the outer edge of desk See Figure 16 KSA 1020 Installation Instructions mounting bracket SC Figure 16 3 Install 3 8 x 1 1 4 hex head lag screw F through bearing D and bracket into hole drilled in Step 2 See Figure 16 4 Ensure bracket flag is in the open position Insert four mounting buttons into four mounting holes on the bracket See Figure 17 J Figure 17 6 Slide buttons into locked position within holes 7 Move flag to closed position in order to fully secure mount to bracket See Figure 15 10 Installation Instructions KSA 1020 11 KSA 1020 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a division of Milestone AV Technol
Download Pdf Manuals
Related Search