Chief Manufacturing Centris FHP-110 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS Small Flat Panel Ceiling Mount with Adjustable Column FHP 110 The FHP is a sleek Centris mounting system designed for all VESA 75mm 100mm compliant displays The mount includes an adjustable column cable management and a variety of screen positioning options The all metal mount is available in either silver black or white c UL Dus LISTED The slender column on the mount is finely finished with easy adjustment between 23 inches and 42 inches in 1 inch incre ments The snap on cable management cover fitting snugly against the column conceals unsightly cabling The mount rotates 360 degrees allowing portrait or landscape mounting of your display The friction adjustable pivot points include 15 degrees of up and down tilt for customized move ment BEFORE YOU BEGIN e Caution To prevent damage to the FHP which could affect or void the Factory warranty and to the equip ment that will be attached to it thoroughly study all instructions and illustrations before you begin the installation Pay particular attention to the Important Warnings and Precautions on Page 1 e The maximum weight to be installed on the FHP ceiling mount is 40 pounds 18 1 Kg e The FHP ceiling mount is designed to be installed using supporting framework The structure to which the FHP ceiling mount is anchored must be capable of supporting five times the total weight of the mount and all attached equip2. RNING Make sure the mount and brackets are correctly oriented CAUTION Check the unit for shipping damage before you begin the installation TOOLS REQUIRED FOR INSTALLATION Saw to cut plastic Electric drill and bit set Phillips Screwdriver Level NOTE Other tools may be required depending on the mounting surface and method of installation CONTENTS PVA VV INGA sese xe eee 2 INSPECT THE UNIT BEFORE INSTALLING 3 PAP ING ALLATION Sn widen eases 3 DISPLAY INSTALLATION sese 4 CABLE MANAGEMENT sese 5 ADJUSTMENT S dei us cine nn ne 5 Installation Instructions FHP DRAWINGS Ceiling Plate Socket Head Cap Screw Nylon Washer Lad Inner Column E a M4 X 7 X 12mm Phillips pan head screws dd a M4 X X 20mm or M4 X 7 X 30mm ae ee a a Phillips pan head screws JUS men Crew Spacers optional 101 60 4 00 25 40 1 00 1082 38 42 61 75 50 80 ie TYP 9X 200 100 3 94 is TO U Phillips Pan Head Nes 100 Adjustment Screw 3 94 A i IL L T KA as NS dia Installation Instructions INSPECT THE UNIT BEFORE INSTALLING WARNING Watch for pinch points Do not put your fingers between movable parts 1 Carefully inspect the FHP for shipping damage If any damage is apparent call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage NOTE Read all instru
3. ctions before starting installation 2 Lay out components to ensure you have all the required parts before proceeding see FHP drawing on page 2 FHP INSTALLATION WARNING It is the responsibility of the installer to verify that the surface to which the FHP is anchored will safety support the combined load of all attached components and equipment Install the FHP as follows 1 Determine the exact mounting location prior to installation considering the unit s swing radius WARNING Improper installation can result in serious per sonal injury Make sure that the structural mem bers can support a redundant weight factor five times the total weight of the equipment if not reinforce the structure before installing the FWP 2 Secure the ceiling plate at the desired location 3 Thread the outer column with pipe adapter securely into the ceiling plate see Figure 1 4 Using the set screw secure the outer column in the ceiling plate 5 Install the inner column into outer column at desired height and secure using socket head cap screw Nylon washer and lock nut see Figure 2 Figure 1 Outer Column Installation Figure 2 Mount on Outer Column Installation Instructions FHP DISPLAY INSTALLATION Install the display as follows VESA Compliant Flush Mounting CAUTION If monitor uses a screw size other than M4 DO NOT use the M4 screws provided Using the wrong screws could result in damage to you
4. isplay on Bracket Installation Instructions FHP CABLE MANAGEMENT WARNING Make sure your cables do not run through a pinch point 1 Route power audio video cables against column allowing suf ficient slack in cables for extension and avoiding pinch points 2 Install top cable cover over cables see Figure 5 3 Measure distance of remaining exposed cables and using a saw or appropriate tool cut lower cable cover to length 4 Install bottom cable cover over remaining exposed cables ADJUSTMENTS CAUTION Overtightening adjustment will cause excessive wear Rotational Tilt Pitch and Roll Adjustment 1 If necessary use a Phillips screwdriver to tighten or loosen the Phillips pan head screw see DRAWINGS on page 3 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained Figure 5 Install Cable Cover Installation Instructions FHP l Installation Instructions FHP NZ 7N a N 0 A i w Ed 3 ds K
5. ment e If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 CHIEF MANUFACTURING INC PART NO 8804 000153 TA 1 800 582 6480 952 894 6280 FAX 952 894 6918 2006 Chief Manufacturing NF 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA Printed in USA 12 06 Ideas Supporting Ideas Installation Instructions FHP A IMPORTANT WARNINGS AND PRECAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre sponding instructions WARNING Improper installation can result in serious personal injury Make sure that the structural members can support a redundant weight factor five times the total weight of the equipment if not reinforce the struc ture before installing the FHP WARNING Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted WARNING The installer is responsible for verifying that the ceiling to which the FHP is anchored will safely support the combined load of all attached components or other equipment WARNING The weight of the display placed on the FHP must not exceed 40 Ibs 18 1 kg the maximum load capacity of the FHP WARNING Watch for pinch points Do not put your fingers between movable parts WA
6. r display 1 Start two M4 X 7 X 12mm Phillips pan head screws in the top mounting holes of your display 2 Matching the hole pattern on your display with the hole pattern on the mount hang the mount from the two screws started in Step A see Figure 3 3 Install two remaining Phillips pan head screws through the mount and into the mounting holes of your display 4 Secure your display to the mount by tightening the four Phil lips pan head screws 5 Connect and secure power audio video cables making sure to leave sufficient slack to allow for movement of the display VESA Compliant Recessed Mounting 1 Place four 1 2 X 3 8 Nylon spacers or four 1 2 X 3 4 Figure 3 Install Flush Mount Display on Bracket Nylon spacers as necessary over the mounting holes of your display see Figure 4 2 Place the mount over the Nylon spacers matching the hole pat tern on your display 75mm or 100mm with the hole pattern on the mount 3 Using four M4 X 7 X 20mm Phillips pan head screws for 1 2 X 3 8 Nylon spacer installation or four M4 X 7 X 30mm Phillips pan head screws for the 1 2 X 3 4 Nylon spacer installation secure the mount to your display 4 Connect and secure power audio video cables making sure to leave sufficient slack to allow for movement of the display Non VESA Compliant Mounts Contact Chief Manufacturing for custom interface brackets Figure 4 Install Recessed Mount D
Download Pdf Manuals
Related Search