Chicago Electric 38391 User's Manual
Contents
1. on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 24 Caution Lead acid batteries generate additional hydrogen gases during charging operations Hydrogen gas is poisonous to breath highly flammable and explosive Only use the Jumpstarter System in a well ventilated area No smoking allowed in the working area Warning People with pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker Operation Warning Electrical shock can cause death or injury Avoid touching exposed conductors of electricity The Jumpstarter System is designed for use with vehicles and boats You will not need a host vehicle or 120 VAC power supply You can also use this system as a portable power source of 12 VDC in remote areas or emergencies To use the Jumpstarter System to start your vehicle 1 Make sure the vehicle or boat to be jump started is not running Make sure the safety switch on the jumpstarter is in the OFF position 2 Connect the black cable to the negative body ground 3 Connect the red cable to the positive terminal on the vehicle s battery 4 Switch the vehicle or boat ignition to the On position and the safety switch on the jumpstarter to the ON position 5 Wait for about a minute or two 6 Switch t2. 8 Button 15 AC Inlet Power Cord 36 Cigarette Lighter Recharger 18 Button Lock Copper Booster Cables 11 Note Connections above are shown to illustrate function Do not attempt to charge the unit through two means at once REV 02 00 REV 04 06 SKU 38391 For technical questions please call 1 800 444 3353 Page 5 at all times If the battery is left in a low charge state it could shorten battery life Keep in mind that the time required to recharge the battery depends on the number of previous battery jump starts To check and see if the battery is low press the Button 15 The Meter 17 will show the battery charge level Green area of meter indicates that it is charged REV 02 00 REV 04 06 SKU 38391 For technical questions please call 1 800 444 3353 Page 6 To charge and recharge using the Power Cord and AC Inlet 1 Insert the Power Cord s female plug into the rectangular AC Input on the side of the unit and the male plug into a 120 VAC outlet 2 For the initial charge allow the Jump Start System to charge for 24 hours For recharges allow the Jump Start System to recharge for 8 to 10 hours Check the recharge progress by pressing the red Button 15 This will show the level of battery power on the Volt Meter 17 3 This Jumpstarter System is equipped with an automatic cut off to help prevent overcharging To recharge using a 12 VDC supply 1 Insert the Cigarette Lighter Recha
3. CHICAGO df vex ated POWer Tools JUMPSTARTER SYSTEM Nifete 31138391 ASSEMBLY AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Copyright 2000 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Revised 08 05 04 06 Specifications ITEM DESCRIPTION Battery Type Sealed lead acid rechargeable 17 amp 900 amps peak 400 amps starting power Rubber insulated 4 copper Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Wear eye protection When working on or around lead acid batteries always wear eye protection 2 Avoid contact with Battery Acid If splashed immediately wash effected area with clean water Co
4. Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children Do not place this unit in direct sunlight direct heat or moisture Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles Do not overreach Keep proper footing and balance at all times Do not reach over or across electrical cables or frames Maintain tools with care Inspect tool cords periodically and if damaged have them repaired by an authorized technician Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears REV 02 00 04 05 SKU 38391 For technical questions please call 1 800 444 3353 Page 3 damaged should be carefully checked to determine that it will operate properly and perform its intended function Do not use the tool if any switch does not turn On and Off properly 22 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 23 Do not operate tool if under the influence of alcohol or drugs Read warning labels
5. he boat or vehicle to the start position for no more than 5 to 6 seconds 7 If the vehicle or boat engine does not start wait at least 3 minutes before retrying Caution Never allow the red and black clamps to touch each other or a common conductor PEO REY DAUE REN O SKU 38391 For technical questions please call 1 800 444 3353 Page 4 8 When the engine is running turn the safety switch to OFF disconnect the black clamp first and return the cable to its stored position on the jumpstarter system 9 Disconnect the red clamp and return the cable to its position on the system 10 As soon as possible recharge your Jump Start System To use your Jump Start System to power appliances 1 Lift up the cover of the Cigarette Lighter Receptacle 18 2 Insert the cigarette lighter Plug from the appliance into the Cigarette Lighter Receptacle 18 3 Turn the Safety Switch to the ON position to energize clamps and connectors Warning When the Jumpstarter System is not in use always turn the Safety Switch to the OFF position This prevents accidental short circuits of the clamps and connectors which could cause fire burns or shock Recharging This unit is rechargeable by using the Power Adapter 22 or by use of the Cigarette Lighter Recharger Cord It is recommended that the battery be kept fully charged s y Recharger Socket afety Switch J Volt Meter 17 Light Case 2 Cigarette Lighter Socket 1
6. ntinue washing area until medical help arrives 3 Connect cables to proper polarities Connect black cable to negative body ground and red cable to positive battery terminal 4 Use this tool in well ventilated areas Do not attempt to jump start vehicle around flammable gases or liquids 5 Do not allow the Black and Red clamps to touch If this happens it can melt clamps or other metal objects Place them only on the corresponding terminals REV 02 00 SKU 38391 For technical questions please call 1 800 444 3353 Page 2 15 16 20 21 12 Volt Systems Only Use only with vehicles and boats with 12 volt electrical systems For emergency use only Do not use this system in the place of a vehicle battery Only use to jump start your vehicle Avoid working alone If an accident happens an assistant can bring help Avoid electrical shock Use extreme caution when clamping around uninsulated conductors or bus bars Prevent body contact with grounded surfaces such as pipes radiators ranges and cabinet enclosures when testing voltages Keep work area clean Cluttered areas invite injuries Avoid damaging Jumpstarter System Use only as specified in this manual Observe work area conditions Do not use tool in damp or wet locations Don t expose to rain Keep work area well lighted Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords
7. rger Plug into the Front Panel port labeled Recharge ea a PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO REV 02 00 REV 04 06 SKU 38391 For technical questions please call 1 800 444 3353 Page 7 r cae F A Y a REV 02 00 REV 04 06 SKU 38391 For technical questions please call 1 800 444 3353 Page 8
Download Pdf Manuals
Related Search