Chamberlain WKP250LM User's Manual
Contents
1. Enter new Master PIN Number BEEP Adding PIN Numbers The WKP5LM can support up to 5 PIN Numbers while the WKP250LM can support 250 Enter Master PIN Number on Keypad 9 BEEP Enter new PIN Number BEEP Erasing PIN Numbers Enter Master PIN Number on Keypad 7 BEEP Enter PIN number you want to remove BEEP BEEP A triple beep indicates a PIN Number has been entered that does not exist The Master PIN Number cannot be deleted Temporary PIN Numbers A temporary PIN Number can be used only once within a 24 hour period NOTE The WKP5LM can hold up to 5 Temporary PIN Numbers while the WKP250LM can hold 15 Enter Master PIN Number on Keypad 5 1 BEEP Enter temporary PIN Number BEEP If the temporary PIN Number applies only to a certain Receiver enter the PIN Number followed by the Receiver Identity 1 4 The result will be a fiv2. Step 3 On Main Keypad enter Master PIN Number 7 Step 4 Then 0 5 NOTE If a siren noise is heard the programming has failed Repeat process The Keypad can be used as a primary or secondary device Accessories should be programmed directly to the primary device Pre Installed Liftmaster Receiver Step 1 Pry open the front panel of the receiver case with a coin or a screwdriver Indicator Light Learn Button Step 2 Press and release the Learn button on the receiver The Indicator Light will light for 30 seconds indicating that receiver is in Learn Mode Step 3 Within 30 seconds enter Master PIN Number on Keypad Step 4 Press 1 Repeat Steps 2 4 for each remote or control device that will be used to access the Liftmaster door or gate operator Erase All Control Codes Press and hold the Learn button on the receiver until the Indicator Light turns off indicating that the receiver memory is clear about 6 seconds Operation To use Keypad enter any valid PIN Number With multiple Receivers enter the PIN Number followed by the Receiver Identity 1 4 Change Master PIN Number Enter existing Master PIN Number on Keypad 0 19 BEEP
3. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON SELLER S PART THIS LIMITED WARRANTY DOES NOT COVER NON DEFECT DAMAGE DAMAGE CAUSED BY IMPROPER INSTALLATION OPERATION OR CARE INCLUDING BUT NOT LIMITED TO ABUSE MISUSE FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT PROBLEMS RELATED TO INTERFERENCE OR REPLACEMENT OF BATTERIES UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE OR INABILITY TO USE THIS PRODUCT IN NO EVENT SHALL SELLER S LIABILITY FOR BREACH OF WARRANTY BREACH OF CONTRACT NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT Some States do not allow the exclusion or limitation of consequential incidental or special damages so the above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state 2009 The Chamberlain Group Inc 114A3531B All Rights Reserved
4. CHAMBERLAIN LiftMaster PROFESSIONAL SECURITY Overview The Wireless Keypad uses a digitally secure intercom link that allows it to control up to four access points The Wireless Keypad is compatible with various Liftmaster Wireless Products Model WKP5LM can hold up to 5 PIN Numbers Model WKP250LM can hold up to 250 PIN Numbers Carton Inventory mm CA Bolt 4 i omm o Screw 4 Washer 4 Allen Wrench Install 4 AA Alkaline batteries not provided Lithium batteries recommended for colder environments Keypad will beep Keypad will continuously beep indicating no Master PIN Number has been programmed Proceed to Initial Setup Modelis WKP5LM amp WKP250LM Wireless Keypad Initial Setup Step 1 On keypad press Step 2 Enter 4 digit Master PIN Number Example 1234 NOTE is the cancel button that will cancel any call or key sequence Multiple Keypads at Same Location NOTE This step applies only if more than one Keypad is being used Step 1 On secondary Keypad enter Master PIN Number Step 2 Then 5 6 NOTE To switch a secondary Keypad to a Main Keypad enter the Master PIN Number followed by D7
5. ME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warranty The Chamberlain Group Inc Seller warrants to the first purchaser of this product for the structure in which this product is originally installed that it is free from defect in materials and or workmanship for a period of one year from the date of purchase The proper operation of this product is dependent on your compliance with the instructions regarding installation operation maintenance and testing Failure to comply strictly with those instructions will void this limited warranty in its entirety If during the limited warranty period this product appears to contain a defect covered by this limited warranty call 1 800 528 2806 before dismantling this product Then send this product pre paid and insured to our service center for warranty replacement Products returned to Seller for warranty replacement which upon receipt by Seller are confirmed to be defective and covered by this limited warranty will be replaced at Seller s sole option at no cost to you and returned pre paid Defective parts will be replaced with new or factory rebuilt parts at Seller s sole option THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF
6. e digit PIN Number example 12341 Mount Keypad It is recommended that Keypad be mounted to a Gooseneck post or non metallic surface If it is necessary to mount Keypad to a metal surface use a non metallic spacer to move the Keypad away from the metal surface Step 1 Choose mounting location for Keypad Remove the back panel and attach it to a solid surface or post Step 2 Mount the Keypad onto the back panel with screws Tighten screws with Allen wrench Keypad Brightness When it is dark the panel will light when it detects movement up to 5 or when a button is pressed Enter Master PIN Number on Keypad 21 2 12 2 0 8 Enter one of the following brightness levels 1 OR 2 OR 3 BEEP Default setting is 2 Battery The AA batteries not provided in the Keypad will typically last up to 3 years depending on use Lithium batteries recommended for colder environments FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 528 2806 www liftmaster com NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HO
Download Pdf Manuals
Related Search