Chamberlain RWA300R User's Manual
Contents
1. r Plug in Base Station Adhere rubber pads to bottom A 9 Volt battery not provided is optional in case of power failures Step 6 A Ensure Base Station and PIR Motion Sensor are in close proximity to each other Press and release learn button on Base Station Buzzer will sound B Within 5 seconds wave hand in front of PIR Motion Sensor Test light will illuminate and Base Station will buzz PIR Motion Sensor Installation Mount PIR Motion Sensor horizontally on solid surface a few feet off the ground and within 900 of Base Station rotate sensor to access screw holes Unit should be able to swivel as needed Attach sun rain shield NOTE Keep PIR Motion Sensor antenna away from metal objects Do not mount PIR Motion Sensor in direct sunlight near moving tree branches or in the path of a sprinkler system Vehicle Alert Installation For cars the best mounting position is about 4 high between 10 20 back and angled to see the back of car after passing the sensor Advanced Features S G COM Common N O Normally Open t ACCESSORY The Base Station has a relay which can activate other devices such as a low voltage doorbell buzzer or light The accessory device will need a separate power supply The accessories can be purchased at any electronics store NOTE Output switching capacity is low voltage max 24V dc or ac 114A3507C Troubleshooting T2. 2 ON OFF Long Buzz ON Short Buzz Default Programming Additional PIR Motion Sensors The Base Station can learn the code of up to 3 additional PIR Motion Sensors responding with unique buzzes To program additional PIR Motion Sensors see Step 6 To order additional PIR Motion Sensors call 1 800 528 9131 Clear Memory Press and hold the Learn Button on the Base Station until 3 beeps are heard PIR Motion Sensor Assembly amp Test Step 1 Attach PIR Motion Sensor box to mounting plate with large silver screw Tighten screw until PIR Motion Sensor stays in place when repositioned Step 2 Install 4 AA Alkaline batteries not provided Lithium batteries recommended for colder environments Test light will flash Switch Settings Antenna PIR Sensor Switch 1 Test Button Switch 2 Switch 1 OFF 15 Detection Range ON 30 Detection Range Default Switch 2 OFF Low Sensitivity ON High Sensitivity NOTE To avoid unwanted detection of small animals move Switch 2 to OFF Insert battery pack facing away from circuit board and attach cover NOTE Ensure the batteries do not touch the circuit board and the antenna and battery wires are not pinched Test PIR Motion Sensor by waving hand in front of sensor Test light should flash Secure cover with the smallest screws Programming PIR Motion Sensor to Base Station Step 5 a
3. may cause undesired operation 2008 The Chamberlain Group Inc All Rights Reserved
4. CHAMBERLAIN Overview The Alert uses a Passive Infra Red sensor to detect movement of people and vehicles while allowing small animals to pass through undetected Carton Inventory Base Station Passive Infra Red PIR exe Rubber Pads Motion Sensor Sun Rain Shield AC Adapter Mounting Plate Operation amp Features Base Station Mute Off Button Contacts Antenna sa AC Adapter Learn Button Base Station Switch 1 Base Station Switch 2 On Off To turn Base Station off hold down the Mute Button until it powers down The Base Station can be turned on by pressing the Mute Button Mute Press and release the Mute Button to put the Base Station into Sleep Mode for one hour After an hour it will activate automatically Model RWAS3OOR Wireless Pedestrian amp Vehicle Alert 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution outputs are suitable ONLY for controlling low voltage devices 24V max ac or dc Battery The AA batteries not provided in the PIR Motion Sensor will last up to 2 years depending on use Lithium batteries recommended for colder environments If Base Station battery optional is low it will beep every few minutes Replace with 9 Volt battery not provided For peak performance inspect batteries annually and replace as needed Base Station Switches Switch 1 OFF Buzzer Off ON Buzzer On Default OFF Switch
5. cotton swab Let it sit inside for a few hours open to the air without the batteries and it should correct itself Check Sensor Switches on PIR Motion Sensor See Switch Settings Base Station beeps every ten minutes The battery in the Base Station is low Replace with 9 Volt battery or operate it using AC Adapter Base Station is not very loud Adjust the volume of speaker An accessory such as a low voltage doorbell buzzer or light can be attached to the relay switch The accessory device will need a separate power supply NOTE Output switching capacity is low voltage 24V max ac or dc NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 528 9131 www chamberlain DIY com NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that
6. he PIR Motion Sensor lights up but the Base Station does not respond The PIR Motion Sensor must be programmed to Base Station See Step 6 Ensure Base Station is on and is not muted If the green power light is not lit or is flashing press the Mute Button on the top of the Base Station to wake it up If the green power is illuminated look at the two small white Base Station switches next to the Learn Button The 1 Dip Switch should be down towards the circuit board If it is up the Base Station has been muted If the Base Station signals when you press the Learn Button it is not muted The Alert is not getting expected transmission range Keep both antennas vertical and keep PIR Motion Sensor antenna away from trees and metal objects Ensure Base Station is in clearest possible sight of the PIR Motion Sensor The less objects between the devices the longer the range PIR Motion Sensor is detecting motion only part of the time To detect cars it is best to mount PIR Motion Sensor at height of cars motor and have it between ten and twenty feet from the road Swivel sensor as needed The Alert is giving false alarms Check for moving tree branches or insects in sensor window PIR sensor can also be triggered by light shining directly in sensor window such as reflected sunlight or motion in front of a light source It is possible that condensation has built up on the sensor Wipe condensation from PIR Motion Sensor with
Download Pdf Manuals
Related Search