Chamberlain CR550 User's Manual
Contents
1. 13 SETTING THE FORCE The force as measured on the closing edge of the door i measured to more than 400 N The Protector System should not exceed 400 N 40 kg If the closing force is Coad eh IR Beams must be installed refer section 16 The force setting regulates the amount of power required to open and close the door Door should be closed before proceeding e Press the purple button twice to enter the opener into OOOOO Learn Purple force adjustment mode The indicator LED will flash quickly e Press the green start button on the bottom of the opener The door will travel to the up limit Press the green start button again the door will travel to the down limit The indicator LED will stop flashing when the force has been learned The door must travel through a complete cycle up and down in order for the force to be set properly If the Opener cannot open and close your door fully examine your door to ensure that it is balanced properly and is not sticking or binding refer section 4 14 TESTING THE SAFETY REVERSE SYSTEM The safety reverse system test is important The garage door must reverse on contact with a 40mm obstacle laid flat on the floor Failure to properly adjust the opener may result in serious personal injury from a closing garage door Operate the door in the down direction The door must reverse upon contact with the obstacle If the door stops on the obstacle2. terminal Twist the two white black wires together and terminate them into the grey safety beam terminal Ensure the trim pot on the opener is set to Os e Turn the opener on e Allow 5 minutes for the beams to self learn to the unit do not walk through the beam during this time e Adjust the trim pot to the desired closing time NOTE The opener will automatically detect the Protector System IR Beams when it is installed and operating for 5 minutes during this time the beams must remain unobstructed The opener will not close unless the beams are aligned IR Beams must be installed to detect a 100mm high obstacle at any point along the floor Red LED Red LED MUST BE ON MUST BE ON IR Beam IR Beam white black wires twisted together Remove cover Push cover plate up then lever out from the button A Door may operate unexpectedly therefore do not allow anything to stay in the path of the door WIRELESS PROGRAMMING OPTIONAL ACCESSORIES NOTE Your transmitter s have already been programmed into your opener Activate the opener only when door is in full view free of obstruction and properly adjusted No one should enter or leave garage whilst door is in motion Do not allow children to operate push button s or transmitter s Do not allow children to play near the door Fix any wall control at a height of at least 1 5m and within sight
3. e If the problem occurs on the first operation of the opener the door may be locked Disable any door locks 11 The opener won t operate due to power failure e Use the manual release handle to disconnect the door The door can be opened and closed manually When power is restored re engage the opener refer section 11 12 Setting the limits manually a Check that the opener position jumper is correct refer Section 7 b Press and hold the BLACK button until the orange indicator light starts flashing slowly then release c Press the BLACK button to move the door UP or the PURPLE button to move the door DOWN until the door reaches the desired UP limit Ensuring there is enough clearance for your vehicle d Press the GREEN start button This sets the UP limit and begins closing the door Immediately press either the PURPLE or the BLACK button The door will stop Adjust the desired DOWN limit using the BLACK and the PURPLE buttons Check to be sure the door is fully closed without applying excessive pressure to the door curtain Press the GREEN start button This sets the DOWN limit and begins opening the door NOTE If neither the BLACK or the PURPLE button is pressed the door will reverse off the floor and the DOWN travel limit will be set automatically e Open and close the door with the GREEN start button transmitter or wall control 2 or 3 times If the door does not stop in the desired UP limit or reverses before the door
4. remove obstacle and repeat limit and force setting sections 12 amp 13 Repeat testing procedure of the safety reverse system Learn Purple sits Qe NB Door must be in closed position SETTING THE FORCE Press the purple learn button twice FAST flashing orange LED Press the green start button to open the door Wait until door is fully open Press the green start button to close the door Orange LED will go out 40mm test obstacle This test should be repeated monthly to ensure the safe operation of your opener 15 FIXING WARNING LABELS Once you have completed your installation and successfully carried out the safety reverse system test outlined above install the warning labels provided with your opener as shown The risk of entrapment label must be installed adjacent to the release handle at a height of less than 1 8 m from the floor The WARNING label must be installed in a prominent 4 WARNING place near any fixed control Any fixed wall control or wireless door control must be mounted at a height of no less than 1 5 m out of the reach of children Ensure the instruction card concerning the manual release of the door is attached to the rope as detailed in section 10 Read the safety instructions page 1 for further details concerning safety Wall control or
5. CARTON INVENTORY Instruction manual this document Warning and risk of entrapment labels Hardware bag Release handle cord and risk of entrapment card 3 Channel mini transmitter 2 Wall or visor mounted transmitter Stop collar Clamp bracket and plate Weight bar Extension poles amp brace 2 k EJ D00Rr REQUIREMENTS HJ TOOLS REQUIRED Ladder Adjustable wrench for U bolts already installed on the door 8mm socket 10 mm socket and 13 mm extended socket and socket wrench 300 mm socket extension for minimum side room installations Drill and 5 5 mm drill bit Phillips head screwdriver Marker pen Door stand or similar device to safely support door not shown 2 a 3 Bee 13mm 10mm 8mm The maximum allowable door height is 3 5m with a maximum curtain area of 13 5 m door height in metres multiplied by the width in metres The door must be spring balanced The Protector System IR Beams must be installed if the force at the edge of the closing door exceeds 400N 40kgf Door axle diameter must not exceed 35mm m B Door area h x w m eg 2 5 x 3 7 5m fig A fig B Direct clamping method Independent clamping method 95 Ensure that there is at least 45mm from the edge of the curtain to the edge of the bracket If th
6. an open door from closing It is STRONGLY RECOMMENDED for homeowners with young children Allow a 15 minute cooling period after 4 minutes of continuous operation of the opener Opening the door manually Door should be fully closed if possible Weak or broken springs could allow an open door to fall rapidly Property damage or serious personal injury could result The door can be opened manually by pulling the release cord down firmly To re engage door pull the release cord down firmly refer section 11 The opener light will turn on e when opener is initially plugged in e when the power is briefly interrupted e when the opener is activated the light turns off automatically after 2 1 2 minutes CARE OF YOUR OPENER When properly installed your opener will operate with minimal maintenance The opener does not require additional lubrication Limit and force settings These settings must be checked and properly set when the opener is installed Weather conditions may cause some minor changes in the door operation requiring some re adjustments particularly during the first year of operation Refer to limit and force setting in sections 12 amp 13 Follow the instructions carefully and repeat the safety reverse test after any adjustment Transmitter Additional transmitters can be purchased at any time Refer to accessories Any new transmitters must be programmed into the opener Transmitter battery If
7. hear a clicking sound The door is now in manual mode and may be opened or closed release cord 5 a To re engage the opener To re engage the opener pull the release cord down until you hear a clicking sound the motor is now ready for operation Overhand knot B SETTING THE LIMITS Travel limits regulate the points at which the door will stop when moving UP or DOWN During the set up procedure the motor will run and operate the door The opener must be fully installed on the door and all installation steps completed before proceeding The opener will operate during this procedure Make sure the door is clear of CHAMBERLAIN obstruction Ensure your hands are away from www chamberlainanz com any moving parts before activating the door CR550 PREPARATION e Position the door about half way and engage the opener section 11 e Remove the lens cover from the opener fig 1 e Connect the opener to a 240 VAC power point and p Oo Connect to 240vac turn on L D and switch on SETTING THE TOP LIMIT Remove cover Push cover plate up then lever out from the bottom e Press and hold the black limit button until the orange indicator LED starts flashing slowly and then release The courtesy LEDs will go to low illumination i Position door midway Ensure motor is engaged e Press and hold the black limit button until the door reisi section11 reaches the desired open p
8. liable to result from the failure Note We request that you retain your sales docket or invoice as proof of purchase and attach it to this manual to enable you to establish the date of purchase in the unlikely event of a warranty service being required Chamberlain reserves the right to change the design and specifications of the Unit without prior notification Some features or accessories of the Unit may not be available in certain markets or areas Please check with your distributor Chamberlain service centre contact details Australia Phone toll free 1800 638 234 Fax toll free 1800 888 121 75 Epping Road North Ryde NSW New Zealand Auckland phone 09 477 2823 Phone toll free 0800 653 667 Fax toll free 0800 653 663 Email customerservice chamberlainanz com Website www chamberlainanz com Trademark of The Chamberlain Group Inc Registered Trademark of The Chamberlain Group Inc 2012 The Chamberlain Group Inc
9. of the door but away from any moving parts ADDING transmitters using the learn button e Press and hold down the transmitter button you wish to program to the opener e The orange LED will flash continuously to indicate it is receiving signal from the transmitter e Press and release the learn button on the opener e The courtesy LED will flash once e Ensure the door is clear of obstruction then test the transmitter DELETING ALL transmitter codes NOTE This deletes all learned transmitters e Press and hold the learn button until the orange indicator light goes out approximately 9 sec 10 18 KEYLESS DEVICE PROGRAMMING OPTIONAL ACCESSORIES Activate the opener only when the door is in full view free of obstruction and properly adjusted No one should enter or leave garage whilst the door is in motion Do not allow children to operate push button s or transmitter s Do not allow children to play near the door Wireless Keypad 8747AML Using the purple learn button 1 Press and release the purple learn button 1 on the opener the orange LED will light 2 Within 30 seconds enter a four digit personal identification number PIN of your choice on the keypad 2 then press and hold the ENTER button 3 Release the button when the opener courtesy LEDs flash once 3 the code is learned Alternate programming method using the multi function control panel optional accessory NOTE This me
10. wireless push button no less than 1 5m Ground level STANDARD INSTALLATION COMPLETE 8 HJ INSTALL THE PROTECTOR SYSTEM IR BEAMS SAFETY FIRST i Whilst Chamberlain have engineered safety features into your garage door opener we urge you to consider fitting IR Beams to your new garage door opener In many countries these devices are compulsory to assist in preventing serious injury or property damage For your own peace of mind and the safety of others please install this inexpensive safety device NOTE This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N 40 kgf After the opener has been installed and adjusted the Protector System IR Beams accessory can be installed Instructions are included with this accessory The Protector System IR Beams provides an additional measure of safety against a small child or animal being trapped under a garage door It uses an infra red beam which when broken by an obstruction causes a closing door to open and prevents an open door from closing and is strongly recommended for homeowners with young children Installing and adjusting e Close the garage door e Turn the opener off e Install the Protector System IR Beams using the brackets wires and instructions provided with the product e Twist the two white only wires together and terminate them into the white safety beam
11. CHAMBERLAIN Convenience with Confidence www chamberlainanz com CR550 Rolling Garage Door Opener Installation and Operating Instructions Owners Copy Please keep these instructions for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY N2966 START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING Failure to comply with the following instructions may result in serious personal injury or property damage Read and follow all instructions carefully The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual rr PPP PP PP gt property damage exists Keep garage door balanced Do not let the garage door opener compensate for a binding or sticking garage door Sticking binding or unbalanced doors must be repaired before installing this opener Do not wear rings watches or loose clothing while installing or servicing a garage door opener Frequently examine the door installation in particular cable springs and mountings for signs of wear damage or imbalance Do not use if repair or adjustment is needed since springs and hardware are under extreme tension and a fault can cause serious personal injury To avoid serious personal injury from entanglement remove all ropes chains and locks connected to the garage door b
12. Clamp the opener to the door axle through the door bracket with the bracket plate 8mm bolts and nuts supplied Tighten sufficiently to fasten the opener firmly to the axle i e 25Nm 28Nm e Remove any ropes used e Independent clamping method If the side room exceeds 95mm clamp independently to the door axle as illustrated in section 3 fig A using 2 separate clamps GQ ATTACH THE RELEASE HANDLE AND CORD e Thread one end of the rope through the hole in the top of the red handle so NOTICE reads right side up as shown e Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping Thread the other end of the rope through the loop of the manual release cable e Adjust the rope length so the handle is no higher than 1 8 m above the floor Secure with an overhand knot If the door is greater than 2 5 m in height the release cord extension kit accessory is required Manual release Warning label NOTE Final adjustment of the handle height should be completed after the opener is installed If it is necessary to cut the rope heat seal the cut end to Release handle prevent unravelling ay OPERATING THE MANUAL RELEASE Disable all locks and remove any ropes connected to the garage door Take care when operating the manual release as an open door may fall rapidly due to weak or broken springs or being out of balance To disengage the opener Pull the release cord down once until you
13. ar in the centre of the door e If the door curtain does not have a lifting handle you will need to drill two 5 5 mm holes through the two marked positions then place the weight bar on the inside of the door e Use the 5 mm bolts washers and nuts provided to fasten the weight bar in place NOTE If the door has a lifting handle remove the handle nuts amp bolts Place weight bar over the handle holes insert extended bolis through the weight bar amp fasten handle back in place kd PREPARING THE OPENER Set opener position left or right hand For left hand side installations For right hand side installations the wire jumper should be removed the wire jumper should be in place factory installed Pr i AMEERLAN I I a os ss Attaching the extension poles if required e Insert the extension poles into the gear e Align the extension pole holes with the gear holes e Using the screws provided secure the extension poles Reinforcing Brace e Align the holes of the reinforcing brace with the two holes as shown and fix in place using the screws provided Drive leg 4 A Reinforcing brace must be used Ei PINNING THE DOOR Note A ballooning door may delay the safety reversal Free curtain Ballooning Add fasteners here response and can compromise garage door security To reme
14. as this electrical fitting does not form a part of the unit opener If this Chamberlain Limited Warranty does not apply you may have rights available to you under the Australian Consumer Law Accessories Warranty Accessories supplied with the unit are warranted for 12 months from the date of installation Liability Australia only Except as set out in the Australian Consumer Law being Schedule 2 of the Competition and Consumer Act 2010 as amended consolidated or replaced 1 all other guarantees warranties and representations in relation to the Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them and 2 under no circumstances will Chamberlain be liable for consequential incidental or special damages arising in connection with the use or inability to use the Unit other than those which were reasonably foreseeable as liable to result from the failure Liability New Zealand only Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees Act 1993 as amended consolidated or replaced 1 all other guarantees warranties and representations in relation to the Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them and 2 under no circumstances will Chamberlain be liable for consequential incidental or special damages arising in connection with the use or inability to use the Unit other than those which were reasonably foreseeable as
15. ction or repair the door e Repeat the limit and force setting in section 12 amp 13 Repeat safety reverse test after adjustments refer section 14 7 The door reverses for no apparent reason and opener lights blink for 5 seconds after reversing e Check the Protector System IR Beams if installed Correct alignment if the red light on the beam is solid 8 The door opens but won t close or reverses while closing e Is something obstructing the door Pull the manual release handle Operate the door manually If it is unbalanced or binding call a trained door systems technician e Clear any ice or snow from the garage floor area where the door closes e Repeat the limit and force setting in section 12 amp 13 Repeat safety reverse test after adjustments refer section 14 e If The Protector System IR Beams is installed check the beams both red LEDs should be on 9 The opener strains to operate door e The door may be out of balance or the springs may be broken Close the door and use the manual release to disconnect the door Open and close the door manually A properly balanced door will stay in any point of travel while being supported entirely by its springs If it does not disconnect the opener and call a trained door systems technician 10 The opener motor hums briefly then won t work e Check that the door is not in manual release mode refer section 11 e The garage door springs may be broken See point 9
16. dy any ballooning place self tapping metal screws or rivets where the curtain leaves the roll Secure these through the curtain into the drum wheel at each end of the roll After determining the correct fastener location as shown lift the door approximately half a turn from the closed position to allow access for drilling Door closed Door can be lifted Door secure EJ INSTALLATION STEPS FOR RIGHT HAND INSTALLATIONS e Ensure that the opener position jumper wire connector is installed refer Section 7 e Place the opener in manual release mode refer Section 11 e Open the roller door fully For safety tie a rope around the door as shown e Mark the position of the door axle on the right hand door bracket Ensure that the U bolt on the left hand non opener side of the door is secure e Carefully remove the U bolt on the right hand side checking that Rope the spring tension inside the roller door is not being released e You will need assistance for the following steps To safely support the door slide or lift the door axle clear of the door iAre all brackets and door bracket supporting the door weight with a door stand or similar ifastenings tightly secured i device Then slip the door opener over the door axle YES proceed to the next NOTE The forks should engage either side of the support step spoke iNO tighten any loose ifastenings before Direct clamping method refer fig 1 Place the opener and oe cain doo
17. e roller door drum is on the edge of the curtain or is a smaller diameter additional clearance may be required If the drum is more than 60mm from the curtain edge or of a smaller diameter extension poles may be required see section 7 Different drum and bracket types may result in the minimum side room clearance not being possible and extension poles being required Ensure there is a power point near the opener EJ TESTING THE DOOR Complete the following test to ensure your door is well balanced and not sticking or binding e Disable all locks and remove any ropes connected to the garage door e Lift the door to about halfway and then release it The door should remain suspended entirely by its spring e Raise and lower the door to determine if there are any sticking or binding points 20 kgf is the absolute maximum allowable to raise or lower the door in any position e If your door does not hold in place or it binds or sticks call a qualified door technician before installing the opener INSTALLING THE STOP COLLAR e Install stop bracket collar on the opposite end to Opener side where the opener is to be installed L e Fit the stop bracket hard against the boss of the door drum Ensure the U bolt holding the door axle to the door bracket is tightly secured i Is stop collar installed YES NO Install the stop collar before proceeding Ky NSTALLING THE WEIGHT BAR PROVIDED e Place the weight b
18. e white safety beam quick connect terminal and both white black wires to the grey safety beam quick connect terminal i ACCESSORIES 1 Model 84330AML 1 channel transmitter 2 Model 84335AML 3 channel mini transmitter 3 Model 8747AML Keyless entry system 4 Model 845AML Multi function control panel 5 Model 760AML Outdoor keyswitch 6 Model 1702AML Keyed outdoor emergency release 7 Model 770AML The Protector System IR Beams Transmitter wall mount bracket e Attach bracket to wall using the two flat head screws provided e Slide the transmitter onto bracket e Fix the warning against entrapment label near the wall control refer section 15 NOTE Do not over tighten screws allow enough clearance to slide transmitter down onto the bracket TROUBLESHOOTING 1 The opener doesn t operate from either the GREEN start button or the transmitters e Does the opener have electric power Plug a lamp into the outlet If it doesn t light check the fuse box e Have you disabled all door locks Review installation instruction warnings on page 1 e Is there a build up of ice or snow under the door The door may be frozen to the ground Remove any restriction e The garage door spring may be broken Have it replaced 2 Opener operates from the transmitter but not from the wired wall control optional accessory e Is the wall control lit If not reverse the two wires If the opener runs check for a faul
19. efore installing the door opener Installation and wiring must be in compliance with your local building and electrical codes The safety reverse system test is very important Your garage door MUST reverse on contact with a 40mm obstacle placed on the floor Failure to properly adjust the opener may result in serious personal injury from a closing garage door Repeat the test once a month and make any necessary adjusiments This opener should not be installed in a damp or wet space exposed to weather This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety PP PrP PP PP These safety alert symbols mean WARNING A possible risk to personal safety or The opener must not be used on a wicket door door within a door The Protector System must be used for all installations where the closing force as measured on the bottom of the door is over 400N 40kgf Excessive force will interfere with the proper operation of the safety reverse system or damage the garage door After installation ensure that the parts of the door do not extend over public footpaths or roads Install the wireless wall control or any additional wall control in a location where the garage door is visible at a height
20. nty our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Chamberlain s warranty Chamberlain warrants to the original purchaser of the Chamberlain CR550 Roller Door Opener Unit that it is free from defects in materials and workmanship for a period of 24 months or 5 000 cycles whichever comes first from the date of purchase when installed in a residential premise with a residential specified garage door that is designed for the sole purpose of domestic domicile A maximum of 10 cycles opening amp closing of the garage door is determined to be at the maximum end of residential use on a daily basis Remote controlled transmitters and accessories included with these units have a 12 month warranty from date of installation These transmitters and accessories are not covered for damage caused by neglect Batteries and globes are not covered under this warranty period It is also a condition of this warranty that the garage door is operable by hand and opens and closes with no more than a maximum of 20kgs of lifting weight Chamberlain recommends that the garage door is serviced by a garage door technician ever
21. of at least 1 5m and out of the reach of children Do not allow children to operate push button s or transmitter s Serious personal injury from a closing garage door may result from misuse of the opener Permanently fasten the Warning Labels in prominent places adjacent to wall controls and manual release mechanisms as a reminder of safe operating procedures Activate opener only when the door is in full view free of obstructions and the opener is properly adjusted No one should enter or leave the garage while the door is in motion Do not allow children to play near the door or door controls Disconnect electric power to the garage door opener before making repairs or removing covers KEEP THESE INSTRUCTIONS NOTE If your garage has no service entrance door a 1702AML outside quick release must be installed This accessory allows manual operation of the garage door from outside in case of power failure CONTENTS PAGE SAFETY INSTRUCTIONS 1 CARTON INVENTORY 2 TOOLS REQUIRED 2 DOOR REQUIREMENTS 2 PREPARE amp TEST THE DOOR 3 4 5 6 INSTALLATION CONNECT ELECTRIC POWER 7 ADJUSTMENT 7 8 INSTALL THE PROTECTOR SYSTEM IR BEAMS WIRELESS PROGRAMMING 10 11 SPECIAL FEATURES 2 ACCESSORIES 12 TROUBLESHOOTING 13 OPERATION OF YOUR OPENER 14 CARE OF YOUR OPENER 14 MAINTENANCE OF YOUR OPENER 14 SPECIFICATIONS WARRANTY 1
22. osition If set too high adjust down using the purple learn button make SET TOP LIMIT sure there is enough room for your vehicle to pass Press and hold black button under ig Flashing orange LED WE courtesy LED dim SETTING THE BOTTOM LIMIT jane Use the black button to adjust up use purple down to adjust if required e Press and release the green start button this sets the UP limit and begins closing the door once the opener starts to move down IMMEDIATELY press and hold the purple learn button until the door reaches the desired closed position then release button For fine adjustment press and release the purple learn button to inch down SET BOTTOM LIMIT Press start button located on the bottom of motor then immediately press the purple button Press and hold the purple button until the door is closed Loood ol Use the black button to adjust up if required SAVE AND TEST e Press and release the green start button this sets the DOWN position and begins opening the door to the fully open position i i E E SAVE AND TEST e Close and open the door 3 or 4 times using the Press the oreen start butlorite green start button to confirm the limit settings open the door and save the limits Courtesy LEDs should now be fully illuminated E Repeat the above procedure if necessary Ate dated eh a NOTE The force must now be set in order to en ian courtesy complete your installation refer section 13
23. r axle onto the door bracket in the position that the door axle was originally Clamp the opener to the door axle through the door bracket with the bracket plate 8mm bolts and nuts supplied Tighten sufficiently to fasten the opener firmly to the axle i e 25Nm 28Nm Remove any ropes used Independent clamping method If the side room exceeds 95mm clamp independently to the door axle as illustrated in section 3 fig A using 2 separate clamps FOR LEFT HAND INSTALLATIONS e Ensure that the opener position jumper wire connector is removed refer Section 7 e Place the opener in manual release mode refer Section 11 e Open the roller door fully For safety tie a rope around the door as shown e Mark the position of the door axle on the left hand door bracket A Ensure that the U bolt on the right hand side non opener of the door is secure e Carefully remove the U bolt on the left hand side checking that the spring tension inside the roller door is not being released e You will need assistance for the following steps To safely support the door slide or lift the door axle clear of the door bracket supporting the door weight with a door stand or similar device Then slip the opener over the door axle as shown NOTE The forks should engage either side of the support spoke Direct clamping method refer fig 2 Place the opener and door axle onto the door bracket in the position that the door axle was originally
24. s a consumer Exclusions If our service centre determines that a warranty claim has been made in respect of a failure or defect arising under or out of any exclusion detailed below such that the claim is not covered under this 114B4542B Chamberlain Limited Warranty we may subject to your other rights and remedies as a consumer charge you a fee to repair replace and or return the Unit to you Exclusions This Chamberlain Limited Warranty does not cover any failure of or defect in the Unit due to 1 non compliance with the instructions regarding installation operation maintenance and testing of the Unit or of any product with which the Unit is used 2 any attempt by a person other than a Professional Garage Door Dealer to repair or dismantle the Unit 3 tampering neglect abuse wear and tear accident electrical storm excessive use or conditions other than normal domestic use 4 problems with or relating to the garage door or garage door hardware including but not limited to the door springs door rollers door alignment or hinges or 5 problems caused by electrical faults or replacement of batteries or light bulbs 6 water or moisture ingress that causes corrosion or electrical malfunction 7 corrosion caused by sea air if located near a waterway beach etc 8 fitment to a commercial door or in a commercial operating application NB A General Purpose Outlet GPO ie power point must be supplied by the consumer
25. stops at the DOWN limit proceed to setting the force section 13 If the door still does not stop at the desired limits is something obstructing the door Disengage the opener Open and close the door manually If it is unbalanced or binding call a trained door systems technician If the door stops at both the desired UP and DOWN limits proceed to setting the force OPERATION OF YOUR OPENER Your opener can be activated by any of the following devices The GREEN start button Hold the button down until door starts to move The wall control outside keyswitch or keyless entry system if you have installed any of these accessories The transmitter or wireless wall control 84330AML Hold the push button down until the door starts to move When the opener is activated by transmitter green start button or wall control e If open the door will close If closed the door will open e If closing the door will stop e If opening the door will stop allowing space for entry and exit of pets and for fresh air e If the door has been stopped in a partially open or closed position it will reverse direction e If an obstruction is encountered while closing the door will reverse e If an obstruction is encountered while opening the door will reverse and stop e The optional Protector System IR Beams uses an invisible beam which when broken by an obstruction causes a closing door to open and prevents
26. thod requires two people if the keyless entry is already mounted outside the garage 1 Enter a four digit personal identification number PIN of your choice on the keypad then press and hold ENTER 2 While holding the ENTER button press and hold the LIGHT button on the multi function control panel 3 Continue holding the ENTER and LIGHT buttons while you press the push bar on the multi function control panel all three buttons are held 4 Release buttons when the opener courtesy LEDs flash once Learn button programming Press the purple learn button orange LED will light Enter 4 digit PIN at keypad within 30s Orange LED will turn off and courtesy LEDs will flash once Programming via multi function control panel 1 Enter 4 digit PIN at keypad within 30s 2 Press and hold down LIGHT button on the motion detecting control panel With the LIGHT button pressed press and hold the PUSH BAR on the motion detecting control panel Release the button when the courtesy LEDs flash once 19 SPECIAL FEATURES 1 Multifunction control panel Connect white red wire to the red wired wall control quick connect terminal and the white wire to the white wired wall control quick connect terminal 2 The Protector System IR Beams Connect both white wires to th
27. transmission range decreases replace the battery MAINTENANCE OF YOUR OPENER Once a Month e Repeat safety reverse test Make any necessary adjustments refer section 12 amp 13 e Manually operate door If it is unbalanced or binding call for professional garage door service e Check to be sure door opens and closes fully Set limits and or force if necessary SPECIFICATIONS Input Voltage Rated Load Max Pull Force 230 240 50Hz 85W 15Nm 450N 8 300mm Max Door Mass 60kg spring balanced Standby Power 3 watts nominal Drive DC gearmotor permanent lubrication 4 5 64 433 92MHz Max Drum Rotations Memory Registers Operating Frequency SPECIAL NOTE Chamberlain strongly recommends that the Protector System IR Beams be installed on all garage door openers 14 CHAMBERLAIN LIMITED WARRANTY Chamberlain CR550 Rolling Garage Door Opener Chamberlain Australia Pty Limited Chamberlain New Zealand Limited Chamberlain the manufacturer of Chamberlain automatic garage door openers is committed to manufacturing and supplying high quality goods As part of this commitment we seek to provide reliable service and support for our goods and are pleased to provide you the original purchaser with this Chamberlain Limited Warranty We also provide the following statement as required by the Australian Consumer Law In Australia in addition to your rights under this Chamberlain Limited Warra
28. ty wire connection at the wall control a short under the staples or a broken wire e Are the wiring connections correct Refer to wired wall control instructions 3 The door operates from the GREEN start button or wired wall control but not from the wireless wall control or transmitter e If the wired wall control is installed and it is flashing ensure the lock feature is off e Program the opener to match the transmitter code refer section 17 Repeat with all transmitters 4 The transmitter has short range e Change the location of the transmitter in your car e Check to be sure the antenna on the bottom of the opener extends fully downward e Some installations may have shorter range due to a metal door foil backed insulation or metal garage siding 5 The garage door opens and closes by itself e Be sure that all transmitter push buttons are off e If the wired wall control optional accessory is installed remove the bell wire from the wired wall control terminals and operate from the GREEN start button or transmitter If this solves the problem the wired wall control is faulty replace or there is an intermittent short on the wire between the wired wall control and the opener e Clear memory and re program all wireless wall controls and transmitters 6 The door reverses and stops before opening completely e Is something obstructing the door Is it out of balance or are the springs broken Remove the obstru
29. y 12 months This garage door service fee will be at the consumer s expense NB The Australian Garage Door Association directs attention to consumers to maintain your garage door in good running order it is important your door is serviced by a professional garage door technician every 12 months or earlier as conditions may require During the applicable Chamberlain Limited Warranty period if you are concerned that the Unit may be defective remove and return the unit freight paid to our service centre address below or call our Customer Service Centre on the toll free number below and a Chamberlain technician will diagnose the problem and advise on the next action steps to take Once the problem has been diagnosed subject to your rights under the Australian Consumer Law with respect to major failures Chamberlain or its Dealer will provide you with repairs to the opener Chamberlain will furnish replacement parts free of charge if non electrical or through the Professional Dealer if deemed to be of a technical nature A service fee for on site service may apply if the fault is not covered under this warranty policy or areplacement unit Repairs and replacement parts provided under this Chamberlain Limited Warranty is provided free of charge and is warranted for the remaining portion of the original warranty period This Chamberlain Limited Warranty provides benefits which are in addition to your other rights and remedies a
Download Pdf Manuals
Related Search