Chamberlain CARTON INVENTORY RWIA User's Manual
Contents
1. CHAMBERLAIN Overview The Intercom has up to a 1000 range and allows multiple simultaneous conversations using a 900 Mhz secure digital radio link The intercoms form an exclusive network and respond only to other intercoms in the network Carton Inventory OO Rubber Pads 2 in Model RWIS Intercom 2 in Model RWIS Operation amp Features Channel Lights Volume Button Microphone Power On Channel Button Learn Button Dipswitch 1 Dipswitch 2 On Off To turn intercom ON press any button To turn intercom OFF hold down the Volume button for 5 seconds Talk Button To talk hold down the Talk button All intercoms in the network that are on the same channel will receive the signal Release the Talk button when done talking and within 10 15 seconds press and hold the Talk button of a different intercom to make a secure channel between the two Once the channel is made the other intercoms in the network cannot hear the conversation Model RWIA amp RWIS Wireless Portable Intercom Channel Button Press the Channel button to set intercom to one of four secure channels or the paging channel The default channel for the intercom is the paging channel where all four channel lights are lit An intercom on a channel can only hear an intercom on the same channel or on the paging channel Volume Pressing the Volume button repeatedly will cycle through volume levels Battery The AA Alkalin2. e batteries not provided will last up to a year depending on use Lithium batteries recommended for colder intercom will emit two beeps every ten minutes An AC Adapter not provided can also be used to power the intercom In this case both the power and channel lights will remain on OPTIONAL Conference Mode Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms can communicate All intercoms must be set to the same channel or the paging channel to be in Conference Mode To put intercom in Conference Mode al set Dipswitch 2 to UP position 1 2 Monitor Mode Monitor Mode is used to monitor the sound in a specific room Place the intercom in the room that is to be monitored and press and hold the Talk and Volume buttons until a tone is heard Any other networked intercom can listen to that room If a specific channel is selected for Monitor Mode then only other intercoms on that channel or on the paging channel can listen When in Monitor Mode the intercom will stay active for 15 minutes then will shut off to conserve battery power The Channel light will begin to flash while in Standby Mode and the intercom will reactivate for an additional 15 minutes when a sound is heard from the room being monitored a Q Voice Activation Mode VOX Voice Activation Mode VOX allows a call to be answered without pressing the Talk button Once a cal
3. in intercom The intercoms are too close to each other A cordless phone cell phone or other radio devices can also cause static Intercom is sending audio while no buttons are pressed The sending intercom is set to Monitoring Mode or Voice Activation Mode and will activate when sound is heard It can be taken out of Monitoring Mode by pressing the Talk button It can be taken out of Voice Activation Mode by setting Dipswitch 1 to DOWN position See Operation amp Features FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 528 9131 www chamberlain DIY com NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards for Home or office use Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2008 The Chamberlain Group Inc 114A3510B All Rights Reserved
4. l is heard on an intercom which has been set to VOX a response can be given by speaking loudly into the intercom There will be a slight delay when VOX is first activated by a voice but will continue to transmit audio until the speaking stops To put intercom into VOX HF place Dipswitch 1 to the UP position 1 2 Assemble Intercom Step 1 Install 4 AA Alkaline batteries not provided Lithium batteries recommended for colder environments Step 2 Adhere rubber pads to bottom Repeat Steps 1 and 2 for any additional intercoms Programming Intercom The intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network Create New Network Press the Learn button on the new intercom until a beep is heard Within 10 seconds put the second intercom into Learn Mode refer to the following table INTERCOM LEARN MODE Press the Learn button until a beep is heard Press and hold both buttons for 5 seconds Each intercom will emit a tone when programmed into network Repeat for any additional intercoms Add to an Existing Network Press the Learn button on the new intercom until a beep is heard Within 10 seconds put any networked intercom into Learn Mode refer to table below INTERCOM LEARN MODE Press the Learn button until a beep is heard Press and hold both buttons for 5 seconds Each interc
5. om will emit a tone when programmed into network Repeat for any additional intercoms NOTE Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared Press and release the Talk button to verify network is complete Troubleshooting Intercom does not function Check batteries in intercom If using an AC Adapter ensure that it is plugged in Ensure intercom is connected to a network See Programming Intercom Ensure that intercoms are on the same channel See Operation amp Features Intercom is not getting expected transmission range Keep antenna vertical Keep intercom away from trees metal objects and electrical wiring Cell phones cordless phones or other radio devices may also limit range Intercom beeps every ten minutes The battery is low in the intercom Replace with AA Alkaline batteries or operate it with AC Adapter not provided A 9 12 volt 500mA AC Adapter may be used center positive polarity on the round plug Need to clear intercom s memory Press and hold Learn button an initial beep will be heard Continue to hold until a second beep is heard about 15 seconds Ensure other intercoms are not activated during this time Intercoms in the network that are on will signal during the clearing process Once memory is clear the intercom can be programmed to a new network Static and feedback is heard
Download Pdf Manuals
Related Search