CDA WC430 User's Manual
Contents
1. 8 10 or 12 e To set the delay timer first switch the dishwasher on by pressing the power button Then p The delay timer will switch on and the selected delay timer indicator will illuminate e To change the duration press the delay timer button again until the required time is shown shown below 6h 4h 2h 6h 4h 2h 2 hours 8 hours 6h 4h 2h 6h 4h 2h 4 hours 10 hours 6h 4h 2h 6h 4h 2h 6 hours 12 hours CE E e Once the delay timer is set then select the programme as described above e To cancel the delay timer before the programme has begun press the delay timer button indicator lights go out Quick wash function This dishwasher is equipped with a function that reduces the duration of the wash minimisin consumption e To set the quick wash function select a programme as described above and then press th quick wash indicator light is illuminated e To cancel the quick wash function before the programme has begun press the quick was indicator light will go out Cancelling or Changing a programme If possible do not open the dishwasher door once the programme has started If it is necessary to cancel or change a programme once it has started follow the steps below e First open the door slightly to reduce the risk of water spillage e Press the Programme Selection button for approximately three seconds until the Progra e Close the dishwasher door to allow the dishwasher to run a drain cycle Once the drain cycle is compl2. better performance CDA recommends the use of separate detergent rinse aid and dishwasher salt rather than combination tablets as separates achieve better wash performance If you do use combination detergents add salt and rinse aid to the dishwasher and then adjust the water hardness setting and rinse aid setting to the minimum When you then use separate detergents again you should fill the salt and rinse aid compartments adjust the water hardness setting to the maximum and run an empty wash then adjust the water hardness setting and the rinse aid setting to the appropriate level Salt To ensure the best efficiency the dishwasher needs soft water Hard water means that lime residues remain on the dishes and the interior of the dishwasher affecting performance The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance This is achieved by using dishwasher salt To add dishwasher salt follow the steps below 1 Remove the lower dishwasher basket and then unscrew the salt compartment cap 2 Fill the compartment with dishwasher salt do not use table salt carefully to prevent unnecessary spillage Before first use you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water up to the brim of the compartment as shown in figure 3 3 Replace the cap and the lower basket When the salt warning light on the control p
3. not cut through the inlet hose and do not put the plastic ho e Children could get locked inside the appliance Therefore when disposing of an old appli aside and damage the door lock so that the door can no longer be closed Recommendations e To reduce energy and water consumption remove all dirt residues from the dishes prio e Only run the dishwasher when fully loaded e Place hollow items bowls glasses and pans face down in the basket e Do not put dishes or cutlery with tobacco ash wax lubricating grease or paint residues Before First Use e Set the water softener level as required by the water hardness in the area e Add 2kg of salt into the salt compartment and then fill with water to the top of the sal e Remove all the packaging materials from the interior of the dishwasher e Fill the rinse aid compartment e Run a hot programme without any dishes in the dishwasher Control Panel Quickwash indicator light Power button WC430 Programme indicator lights Salt indicator light Delay timer indicator lights Programme selection button Delay timer button Starting a Programme e Turn on the water tap e Press the Power button e Press the Programme Selection button until the required programme light is illuminated When you close the door the dishwasher will beep once and the programme will start auto The Delay Timer This dishwasher is equipped with a variable delay timer which can be set for 2 4 6
4. Salt compartment cap not completely closed Poor appliance earth check mains electrical supply There are rust stains on the dishes The door is not opening or closing properly Door tension not correctly adjusted for the d cor door 12 Electrical information Warning This appliance must be earthed Green amp Yellow to Earth The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug To cha follow the steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to connect an alternative plug If the fitted plug is not suitable for your socket outlet then it should be cut off and dispose electric shock A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e The wire which is coloured GREEN and YELLOW must be connected to the terminal whic by the Earth symbol ne or coloured GREEN and YELLOW e The wire which is coloured BLUE must be connected to the terminal which is marked with coloured BLACK or BLUE e The wire which is coloured BROWN must be connected to the terminal which is marke coloured RED or BROWN If in doubt regarding th
5. WC430 Integrated CD A Slimline Dishwasher Manual for installation Use and Maintenance Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorre product Please note that CDA reserve the right to invalidate the guarantee supplied with th installation or misuse of the appliance This appliance is not designed to be used by people including children with reduced capacity or who lack experience or knowledge about it unless they have had supervision the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenan qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes oer al Ni um per This appliance has been designed for domestic use only Commercial use will invalidate the CE Declarations of Conformity This appliance has been designed constructed and marketed in compliance with safety re 89 336 EC 2006 95 EC IEC436 DIN44990 EN 50242 IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN DIRECTIVE 2002 96 EC At the end of its working life the product must be taken to a special local authority waste c providing appliance recycling services Disposing of a household appliance separately avoids possible negative co
6. ake sure the door is closed properly Make sure the drain hose is not kinked or bent Drain fault Make sure the drain hose is correctly installed Siphoning Make sure the drain hose is correctly installed Failure Code and Troubleshooting Check the plug fuse and circuit breakers of the mains supply The water tap is turned off The programme will not start The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked The water drain hose is blocked or kinked Water remains inside the dishwasher at the end of the The filters are blocked programme Power failure The dishwasher stops in the middle of a programme Water inlet failure Programme is on standby Poor loading of dishes hinders wash performance Insufficient detergent added Inappropriate wash programme selected Spray arm blocked Filters clogged or incorrectly fitted Water drain pump blocked Wash performance is of a low standard Insufficient detergent added Rinse aid setting is too low White stains on the dishes Insufficient dishwasher salt added Water softener setting is too low Salt compartment cap not completely closed A programme without a drying stage was selected Rinse aid setting is too low Dishes unloaded too soon allow time for drying The dishes are not completely dry at the end of the programme Different sets of cutlery should be kept separate Too much salt Water softener setting is too high
7. anel illuminates you should refill the salt compartment with salt only do not add water to the salt compartment after the first use You should run a programme immediately after adding dishwasher salt to prevent any damage to the dishwasher systems Softener Adjustment The efficiency of your dishwasher depends on the softness of the tap water To ensure best efficiency the dishwasher is equipped with a system that reduces the hardness in the mains water supply The efficiency will increase when the system is correctly set To find out the water harness level of your water supply contact your local water board To set the softener adjustment system unscrew the cap from the salt container and rotate the ring indicated in figure 4 according to the table below Water Hardness Selector position Clarke degrees consumption Grams cycle 4 60 gt 71 gt 89 gt 8 9 mmol l Rinse Aid To fill the rinse aid compartment 1 Open the rinse aid compartment by turning and removing the cap as shown in figure5 2 Fill the rinse aid compartment until the rinse aid indicator goes dark as shown in figure 6 where a indicates the compartment is empty and b indicates the compartment is full 3 Replace the cap ensuring the markers on the cap line up with the compartment prior to screwing the cap back in place Rinse Aid Adjustment The level of r
8. cm Depth 55cm Height 82 cm Capacity 9 standard place settings Mains water pressure 0 03 0 6 MPa Power voltage 220 240V 50 Hz Rated current input 10A Total absorbed power 1950 W Programme Listing Intensive Normal Economic Glass Prewash 70 wash 55 wash 50 wash 45 wash No heat Level ofsolt_ High Medium Sal NA Detergent A B A B A B A A NA amount A Main B Prewash Cold prewash Cold prewash Hot prewash AI CRIE Programme duration mins standard quick 112 94 102 90 162 140 92 82 32 28 12 12 0 80 0 76 0 75 0 65 0 27 0 24 0 02 0 02 k i BE The values and times provided above have been obtained under laboratory conditions acco Electricity consumption kW hours standard quick 1 36 1 25 1 00 0 93 Water consumption litres standard quick 18 16 15 14 information can change depending on the conditions of the dishwasher s use and environ pressure water input temperature and environment temperature Laboratory measured value in accordance with European standard EN50242 Care and Maintenance Before beginning any care or maintenance you should always disconnect the appliance from the electricity supply and also turn off the water supply Door seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residue Filters You should clean the filters at least once a month e Remove the lower basket e Remove
9. e electrical connection of this appliance consult a qualified electrician supply cable the appliance may require removing for servicing N B Ensure that the plug socket is situated in an easily accessible place 13 14 Installation Do not install this appliance if it is damaged in any way Installing a damaged appliance may invalidate the warranty The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation Ensure the appliance is level by adjusting the feet as necessary Only use the water inlet supplied with the appliance If the water pressure is above 10 bar a pressure relief valve should be used After connecting the water supply check to ensure there are no leaks The water outlet can either be connected to a water drain or to a sink outlet spigot This connection should be at a minimum of 50 cm and a maximum of 110 cm from the floor The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher CDA To contact our Customer Care Department or for Service please contact us on the details below
10. ete the dishwasher can now be set to a new programme if nece Please note If the cancelled programme has already used the detergent and drain detergent dispenser must be refilled At the End of a Programme When the dishwasher programme is complete the dishwasher will beep six times and the Pr out Open the dishwasher door e Press the Power button to switch off the dishwasher e Turn off the water tap and remove the plug from the power socket Please note The dishwasher will automatically continue on the programme it has opened or in the event of a power cut Detergent To fill the detergent dispenser 1 Push the latch to open the dispenser 2 Add the required amount of detergent to the main detergent dispenser If your dishes are in need of an intensive wash then add 5 cm of detergent into the prewash section of the dispenser 3 Then close the detergent dispenser lid until the latch locks Please note You should only use detergents designed specifically for use in dishwashers Combination detergents e g 3 in 1 tablets must not be used in any quick wash programme If using dishwasher tablets always use the detergent compartment do not put them in the main body of the dishwasher or in the cutlery basket The solubility of dishwasher tablets can vary depending on the temperature and duration of the programme As a result it is recommended that powder detergents should be used in the shorter programmes to allow
11. inse aid use is preset to 3 You can adjust the level of rinse aid use by adjusting as shown in figure 7 If water stains form on the dishes after a wash the level should be increased If blue stains which can be wiped away are left on the dishes after a wash the level should be decreased Please note Rinse aid ensures better quality wash results and increased drying performance General Information To adjust the height of the upper basket e Open the basket retaining clips as shown in figure 8 by turning them to the side e Remove the upper basket and relocate the alternate set of wheels on the runner as shown in figure 9 pushing the basket back into place e Close the basket retaining clips e The images below are designed as guidance as to best practice for loading the dishwasher Information on reference tests implemented in compliance with EN 50242 Appliance loaded in accordance with standard specifications Example of loaded dishwasher See below Capacity 9 place settings Reference programme Light wash Rinse aid setting 5 Detergent 5g 22 Height adjustable top basket must be fitted in the uppermost position If the reference tests do not comply fully with EN 50242 e g degree of soiling type of dishes and cutlery etc contact the appliance manufacturer before starting the test Upper basket Lower basket Hy UKA 4H ee TIATA AAT l A Bel CE AAN A Technical Information Width 44 6
12. nsequences for the and health It also enables the constituent materials to be recovered saving both energy and reminder of the need to dispose of household appliances separately the product is marked wheeled dustbin X Important e Read the instructions prior to installation and use of the appliance e Do not lean or climb on the open dishwasher door to prevent damage e Close the dishwasher door after use to prevent accidents e Use only detergents salt and rinse aid specifically designed for dishwashers e Do not put solvents in the dishwasher detergent compartment to prevent risk of explosia e Only put dishwasher safe items into the dishwasher If in doubt check with the manufact e Take care when loading the dishwasher to observe the recommendations for best loading that sharp objects such as knives are placed blade down to prevent accidents e Do not open the dishwasher door when a programme is running If it is necessary to do s only slightly to allow the dishwasher to pause the programme and prevent any water spilli water in the dishwasher can be very hot when the programme is running e When the dishwasher is not in use we reccomend that you turn off the water supply at t the main supply e Ifyou are leaving the dishwasher for an extended period you should leave the door slight formation of unpleasant smells e The plastic housing on the water inlet pipe contains an electrically operated valve The are inside the inlet hose Do
13. the filter assembly by pulling upwards on the cup handle e Remove the fine filter from the filter You should clean and rinse the filters thoroughly before replacing the filters in reverse order to that above Please note Never run a programme without the filters in place Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance Spray arms You should clean the spray arms at least once a month e Remove the lower basket e Pull the spray arm upwards to remove it e To remove the upper spray arm first remove the nut on the upper spray arm by turning it as shown You should clean the upper spray arms thoroughly before replacing them Ensure that the upper spray arm nut is securely tightened when refitting the upper spray arm Dishwasher interior To deal with accumulation of dirt oil or limescale in the dishwasher run an intensive programme with detergent when the dishwasher is empty Alternatively there are specialist dishwasher cleaners available that can be used 10 Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem w Door problem Make sure the water inlet tap is fully open Make sure the water supply hose is not kinked or bent Close the water tap separate the ae problem water inlet hose from the tap and clean the filter Make sure the drain hose is correctly installed M
Download Pdf Manuals
Related Search