Cateye CC-FR7CL Owner's Manual
Contents
1. The specifications and design are subject to change without notice Limited Warranty 2 year warranty for computer sensor only excluding parts and batteries If trouble or damage occurs during normal use the product will be repaired or replaced free of charge Type your name address date of purchase and the situation of trouble clearly on the warranty certificate and send it back to the appropriate service center together with the product Insurance handling and transportation charges shall be borne by the customer After being repaired or replaced the product will be shipped back to the customer CAT EYE co LTD 2 8 25 Kuwazu Higashi Sumiyoshi ku Osaka 546 0041 Japan Attn CAT EYE Customer Service Section Service amp Research Address for United States Consumers CAT EYE Service amp Research Center 1705 14th St 115 Boulder CO 80302 Phone 303 443 4595 Toll Free 800 5CATEYE Fax 303 473 0006 e mail service cateye com URL http www cateye com The following parts are available 169 6693 169 6673 169 6663 Parts Kit Sensor Bracket Kit g z a 3 lt gt Py 169 6773 169 9691 166 5150 Attachment Kit A Magnet Lithium Battery CR2032 A 169 6667 169 6669 169 9760 169 9690 hw Center Stem Mount Kit Magnet for Composite _ Hi Power Wheel v Mount Kit Wheel Magnet a ECO2. CAT EYE Cordless 7 CYCLOCOMPUTER CC FR7CL E OWNER S MANUAL CAT EYE U S Pat Nos 4633216 4636769 4642606 5236759 Pat and Design Pat Pending Copyright 2002 CATEYE Co Ltd CCMFR7CL 021210 Printed in Japan 066600165 1 IMPORTANT PLEASE READ INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO INSTALL AND USE YOUR CAT EYE CORDLESS 7 COMPUTER Installation of Computer Max Magnet Distance 70 cm Sensor Transmitter Nylon Ties S x 2 Nylon Ties L x 2 Secure bracket to handlebar with nylon ties fig A Slide computer into mount until it snaps in place H Mount the wheel magnet to a spoke on the front Q wheel fig B so the magnet faces the sensor Va Secure the sensor to fork leg as shown fig C NOTE The distance between the computer and the sen sor must not exceed 70 cm f the sensor is too far away from the computer head the speed signal will not register on the computer For best results mount the sensor as high on the fork leg as reasonably possible so that the sensor is within transmission range to the computer However the sen sor must be close enough to spokes to allow proper dis O tance to magnet see below Front Fork Sensor Screw Front Fork 5 TT ID i Sensor Base i KC Sensor Base fig C f NOTE When the wheel rotates the magnet MUST line up with the mark on the sensor Y ALSO NOTE Magnet must pass within 5 mm of the sensor
3. e f the gaps between the buttons and the unit get clogged with mud or sand wash with water Replacing Battery Computer If the screen gets dim please replace the battery Before replacing bat tery write down your Odo data and input it again after all clear operation This way you can retain your Odo data and continue to count even after replacing the battery e Insert a new lithium battery CR2032 with the mark facing up e After replacing battery do all clear operation and set up the unit again Sensor If the sensor pulse symbol on the display gets dim please replace the battery After replacing the battery check the position of the sensor and How Mode Shifts in Lower Display 2seconds MODE Pressing MODE and ST STOP button simultaneously for a few seconds in Mx mode the computer will go to sleep mode Dual Tire Size You can set 2 SO different wheel E circumferences QY V Tm Elapsed Time i g ie 0 00 00 9 59 59 A How to Switch Wheel and Vv Average Spee aes a f 0 0 105 9 km h 19 0 0 65 9 mph SETP gt 99 Hold down 2 seconds in Odo MODED If Elapsed Time exceeds 27 hours or Trip Distance exceeds 999 99km Average v Speed shows E and ceases calculation Mx Road MTB A Racer Maximum Speed ST STOP Q Mx de 7 0 0 4 0 105 9 km h Press rustor 0 0 3 0 65 9 mph 2 seconds v How to Change Wheel Circumference Default figure n Wheel A 2096 wo Odo Road C
4. be typical for mountain bikes Troubleshooting No display The battery in the computer run down Replace it with a new one and do all clear operation Incorrect data appears Do all clear operation Before this operation write down your Odo data and input it again after all clear operation In this way you can continue to accumulate your Odo Cannot start measuring by START STOP button Is the icon on To operate manually switch off the Auto Time Sensor pulse indicator does not flash Current speed does not appear If the sensor pulse indicator fails to flash first spin front wheel to align computer with sensor Indicator will flash if computer is working If not this will pinpoint the problem to be 1 dead battery 2 distance between sensor and unit is over 70cm Is the clearance between the sensor and the magnet too large Are the magnet s center and the sensor s marking line aligned Re adjust the positions of the magnet and the sensor Is the distance between the computer and the sensor too long Adjust the sensor s position so that the distance becomes less than 70cm The battery in the sensor run down Replace it with a new one In winter battery s performance is degraded The battery in the computer run down Replace it with a new one and do all clear operation Maintenance e To clean the computer or accessories use diluted neutral detergent on a soft cloth and then wipe it off with a dry cloth
5. f not it will not trip the sensor as it passes and the computer will not register speed Adjusting the sensor position higher or lower on the fork leg or by rotating the sensor on the fork mount may be required to achieve proper distance to the wheel magnet Less than 5mm center l l l Magnet s T Test by spinning the front wheel Computer screen should show speed If not make sure 1 the magnet is close enough to sensor within 5 mm and 2 the sensor KE N OK is close enough to computer head within 70 cm and 3 Har nothing is obstructing the line of sight between the sen u for Sensor Pulse Indicator eee ee ae Precautions l e Do not concentrate too much on the computer operations while riding l e Be sure to securely mount the magnet sensor and bracket on your bicycle and alweys check to insure they are mounted securely AN e Used batteries must be disposed of properly and in accordance with all local regulations e Never disassemble the computer e For cleaning use mild soap and a soft cloth Wipe dry with a soft cloth Paint thinner benzine alcohol or other chemicals may damage the surface This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Modif
6. the figure 700 x 30C a 700 x 32C ST STOP 700C Tubular 700 x 35C SET POO 700 x 38C 700 x 40C A iiai The tire size is marked on Setup Completed To Tm In this state Auto Time is ON hath sidesof the tire Operation of Computer Speed Scale Indicator mph or km h on main display flashes Speed Scale Indicator when computer is measuring speed Display Features Power Saving Function When the unit doesn t receive signal for ten minutes it enters into power saving mode No signal Co ieee Speed upper display 10 minuets 1 0 0 4 0 105 9 km h P z mn a a 0 0 3 0 65 9 mph Display Modes Press MODE button to shift lower display from Toa p P one mode to the next The display modes change from Elapsed i Time Tm to Average Speed Av to Maximum Speed Mx to Sensor Pulse Indicator i A Flashes in synchronization with later I padit signal from sensor 21538 SLEEP i Power Saving Mode Sleep Mode Total Odometer Odo to Trip Distance Dst Wheel Icon Auto Time Icon When wheel starts rotating To wake up the unit Shows which Starts stops measuring it returns to normal mode press MODE button or CLOCK TIME Hold MODE button for 2 seconds to display Clock wheel is selected automatically ST STOP button Time this works in any of the display modes To set correct Clock Time press SET button when Clock Time is showing in lower display Use MODE button t
7. UJET whee B 2050 I Total Distance lt 4 gt ie J 45 0 0 99999 km mile SETE Increases figure wdMoDE MODE a ST STOP Press simultaneously i Decreases figure Dst Dst ef 5 A SO I Trip Distance MTB UJ ie j 0 00 999 99 km mile From any mode 4 y How to Adjust Clock 4 If Km h is selected for speed scale it becomes 24 hour 2K t S clock If mph is selected it becomes 12 hour clock Returns to MODE Increases above mode SETPROD q figure SET Poo i3 1C MODE 2 15 98 P 2 1638 Clock Decreases 15 99 0 00 23 59 we 1 00 12 59 SETPOO er Ace Battery Computer Lithium Battery CR2032 X 1 Sensor Lithium Battery CR2032 X 1 Battery Life Computer approx 1 year in the case of being used for 1 hour every day Sensor until Total Distance reaches about 10 000km 6 250mile This is the average figure of being used under 20 C temperature and the dis tance between the computer and the sensor is 65cm 4 bit 1 chip microcomputer crystal controlled oscillator Liquid crystal display No contact magnetic sensor 10mm 2999mm default figure A 2095mm B 2050mm Controller Display Sensor Wheel Circumference Range Working Temperature 0 C 40 C 32 F 104 F Dimension Weight 1 19 32 x 2 7 32 x 27 32 40 x 56 5 x 21mm 1 060z 30g The factory loaded battery life might be shorter than the above mentioned specification
8. ications The FCC requires the user to be notified that any changes or modifications made to this device that are Ut expressly approved by Cat Eye Co Ltd may void the user s authority to operate the equipment About cordless system The sensor picks up the wheel revolution signal and transmits the signal to the computer the computer calculates and displays the data on the screen CAUTION In order to prevent external signal interference the signal reception range is limited For best performance the distance between the sensor and the computer must be kept within 70cm Attach the sensor at the upper part of your fork so that the distance becomes less than 70cm The signal reception range may shorten as a result of low temperature or lowered battery power In the following places and circumstances interference may occur resulting in malfunction e Near railroad crossing in train cars e Near other cordless devices television personal computer high power lighting system e Near the places where strong electromagnetic wave is generated near television radio station near radar base e When being very close to another bicycle which also has a cordless cyclocomputer on its handlebar Computer Set up for first use or after replacing battery Press All Clear button AC e Stored data is erased e Computer power is started e Total Odometer read s zero e All digits shown then fades e Flashing km h remains AC Butto
9. n a o SET button AC button ST STOP button s MODE button 2 Adjust between mph or km h by pressing the MODE button gt km h a mph MODE Get your wheel circumference Use the below table as the rough guide O Press the SET button to lock in your choice OR fs 3 Tire Size if you want to input previous mileage hold the J2 x175 MODE button before pressing the SET button for 14x1 50 2 seconds 14x1 79 P 16x1 50 e Flashing Odometer digits will appear 16x175 e MODE button increases the digit number 18 x 1 50 e START STOP button moves to the next digit B AE e Press the SET button when complete 20 x 1 3 8 22 x 1 3 8 22x 1 1 2 24x1 SETPROO lt 24 x 3 4Tubular MODE 24x 1 1 8 24x 1 1 4 om inorease 2442 00 nnnann lt q the figure 94x 2 125 uuuuu m MODE 26x 7 8 26x 1 59 5 we 26 x 1 65 A move to the next digit 26x 1 25 E V Isso sears ai 26x 1 1 2 nna 26 x 1 40 UIU I 26x 1 50 iz 26x 1 75 26x 1 95 26 x 2 00 SET POO 26x 2 10 26 x 2 125 3 e Wheel circumference number is shown se x33 e Look at chart to find TIRE SIZE in mm 77 PE e To increase TIRE SIZE press MODE button 27 x 1 1 8 e To decrease press START STOP button a x ni e 10 2999 mm can be registered 650 x 35A e Press SET button when finished 650 x 38A 650 x 38B increase z0x 88 the figure x ii lt A d 700x200 6 MODE 700 x 23C 700 x 25C engg decrease 700 x 28C
10. o increase the digit number and press SET to change to next digit Press SET button when complete AUTO TIME When this is activated the computer will auto matically start and stop measuring Elapsed Time Tm Average Speed Av and Trip Distance Dst as soon as the bike starts moving AUTO TIME is activated when icon shows in main Tm display lav SETP 9 J pot To turn feature on or off press SET button while lower display Dst is in Elapsed Time Tm Average Speed Av or Trip Distance Dst Press SET button in mode For best results operate the computer with activated 1 Av or Dst MANUAL MODE Press the START STOP button to start the Ss Elapsed Time Tm Average Speed Av and Trip Distance Dst V measurement ONLY IF AUTO TIME is not activated A Start Stop Reset Time Distance Average To reset zero out ride data Elapsed Time Trip Distance Average Speed and Max Speed press MODE and START STOP simultaneously Total Odometer is not reset Equo ST STOP Computer Features Power Saving Function e Power saving mode No signal for 10 minutes e Sleep mode No signal for 2 weeks e Wake mode Press MODE or START STOP button Dual tire size e Two different wheel size can be programed e Press MODE and START STOP simultaneously for 2 seconds to switch size and e Wheel size is designed for road bikes Wheel size is designed for slower speeds that can
Download Pdf Manuals
Related Search