Casio 5057 User's Manual
Contents
1. performing any operation it will return to the Timekeeping Mode automatically e If you do not perform any operation for about two or three minutes while a setting mode is selected the watch will exit the setting mode automatically Scrolling e The and buttons are used to change the hand setting in various setting modes In most cases holding down these buttons will start high speed movement of the applicable hand s and day e High speed movement of the hands and day will continue until you press any button or until the moving hand s and day finish one complete cycle One complete cycle for the hands is 24 hours One complete cycle for the day is 31 days Specifications Accuracy at normal temperature 20 seconds a month Timekeeping Hour minutes hand moves every 10 seconds seconds 24 hour day day of the week Calendar system Full Auto calendar pre programmed from the year 2000 to 2099 Stopwatch Measuring capacity 59 59 95 Measuring unit 1 20 second Measurements Elapsed time cumulative elapsed time lap time Other Section distance input Input range 0 0 to 14 9 section average speed indication Alarm Daily alarm Battery One silver oxide battery Type SR927W Approximately 3 years on type SR927W 10 seconds of alarm operation per day2. time from the point the cumulative elapsed time operation is started up until it was stopped Does not include any time when the stopwatch operation was paused Lap time Time of each particular lap e Never operate the stopwatch while operating a motor vehicle Doing so is very dangerous and can cause an accident The initial factory default setting for the distance value is 1 0 For information about inputting a distance see To specify a course or section distance Average Speed Indication The stopwatch second hand will indicate the average speed value after you stop an elapsed time measurement or display a lap time The center dial hand points to Speed value Stopwatch second hand SPEED SPD while the average speed is being indicated Stopping an Elapsed Time or Cumulative Elapsed Time Measurement Two seconds after you stop an elapsed time measurement operation by pressing 8 the stopwatch second hand will indicate the speed for two seconds After that the stopwatch second hand will move back to the elapsed time seconds position Lap Time Measurement Center dial hand Two seconds after wo a lap time measurement operation by pressing the stopwatch second hand will Average Speed indicate the speed for two seconds After that the stopwatch second hand will move to the ongoing elasped time operation Stopwatch e If the value you input for the distance was in kilometers second hand the indicated speed values wi
3. MO0905 EA Operation Guide 5057 Getting Acquainted Congratulations upon your selection of this CASIO watch To get the most out of your purchase be sure to read this manual carefully About This Manual Stopwatch second hand What to do if the center dial hand is stopped Minute hand The watch is shipped from the factory with the center dial hand stopped in order to conserve battery power Even though the center dial hand is stopped the watch continues to maintain the current time internally If the center dial hand is stopped when you purchase the watch press any one of the watch s buttons to start hand movement Hour hand Center dial hand 24 hour hand Day Upper right dial hand Center dial hand General Guide Press CASIO e Button operations are indicated using the letters shown in the illustration e The upper right and center dials indicate various types of data depending on the currently selected mode e Each section of this manual provides you with the information you need in order to perform operations in each mode Further details and technical information can be found in the Reference section Note that CASIO COMPUTER CO LTD assumes no responsibility for any damage or loss suffered by you or any third party arising through the use of this product or its malfunction Stopwatch Mode When the stopwatch is reset to all zeros Time Date Adjustment Hold down fo
4. ated by the center dial hand ON or OFF Adjusting the Home Positions If you notice that the watch hands are not indicating 12 o clock ON OFF settings or other indicator settings correctly you can adjust the home positions of the hands manually to correct them To adjust the home positions 1 In the Timekeeping Mode as you hold down hold down for about three seconds until the watch beeps e This indicates that the watch is in the time and day home position adjustment mode e The center dial hand is in the proper home position if it moves to 0 If it doesn t use to move the center dial hand to 0 e The stopwatch second hand also is in the proper home position if it moves to 12 o clock If it doesn t press to move it to 12 o clock Stopwatch second hand Center dial hand Correct center dial hand and stopwatch second hand home positions After confirming that the center dial hand and stopwatch Minute hand second hand are both at the proper home positions Hour hand press This will switch to hour hand and minute hand home position adjustment e The hour hand and minute hand are at their proper home positions if they both move to 12 o clock and if the 24 hour hand is pointing at hour 24 If the hands are not positioned correctly use and to move all three hands to their proper home positions e The 24 hour hand moves in accordance with the hour minute and se
5. bout two seconds e Pressing to display the current lap time also will start timing of the next lap This means that the stopwatch does not maintain the total elapsed time or total cumulative time in this case e The stopwatch will continue to time the next lap Center dial stopwatch internally even while the current lap time is displayed 1 20 second hand e If a distance value is input performing a lap time operation will cause the stopwatch second hand to stop at the current lap time for about two seconds The stopwatch second hand will then move to the speed indication of the lap for about two seconds After that it will move to the ongoing elapsed time operation position 3 Press 8 to stop the stopwatch This will cause the final lap time to appear on the display e Press to reset the stopwatch Upper right dial stopwatch minute hand Stopwatch second hand Average Speed You also can input the distance of the course or a particular segment of the course of the race you are watching That distance is used along with the elapsed time cumulative elapsed time or lap time measured by the watch to calculate and display the average speed for the course or segment The average speed that appears for an elapsed time cumulative elapsed time or lap time is calculated based on the times described below Elapsed time Time from the point the stopwatch operation is started up until it was stopped Cumulative elapsed time Total
6. cond settings As you set the time take care to ensure that the 24 hour hand also is at the Correct hour and minute correct position hand home positions 24 hour hand CASIO Operation Guide 5057 CASIO Upper right dial hand 3 After confirming that the hands are in the correct home positions press This will advance to the upper right dial hand home position adjustment e The upper right dial hand is in the correct home position if it points to 60 If it doesn t use to move the upper right dial hand to 60 4 After confirming that the upper right dial hand is in the correct home position press This will advance to Correct upper right dial day home position adjustment 5 e The day is in the correct home position if it shows 1 hand home position If it doesn t use and to change the day to 1 Pressing here will return the center dial hand and stopwatch second hand home position adjustment in step 1 of this procedure 5 To return to the Timekeeping Mode press Pressing will cause the watch to beep twice Correct day home position Reference This section contains more detailed and technical information about watch operation It also contains important precautions and notes about the various features and functions of this watch Auto Return Features e If you leave the watch in the Alarm Mode or the home position adjustment mode for two or three minutes without
7. g will not appear for about one second e The elapsed time measurement will not start if you press in the Timekeeping Mode while either of the following conditions exists While an alarm is sounding While the watch is changing from one date to the next at midnight 2 Press to stop elapsed time measurement e You can restart and stop elapsed time measurement as many times as you like by pressing e The center dial hand rotates during the first 60 seconds only and then stops When elapsed time measurement is stopped by pressing 6 the center dial hand jumps to the 1 20 second indication which is kept internally e Stopping a timing operation will cause the stopwatch second hand to stop at the elapsed time seconds position It will remain there if there is no distance value input If a distance value is input the stopwatch second hand will then move to average speed indication after about two seconds After that it will move back to the elapsed time second position e After you are finished measuring elapsed time press to reset the stopwatch to all zeros e To return to the Timekeeping Mode press while the stopwatch is reset to all zeros To measure lap times 1 In the Timekeeping Mode or the Stopwatch Mode press 8 to start an elapsed time measurement operation Press to display the current lap time Each press of displays the current lap time up to that point e The lap time will remain displayed for a
8. ll show kilometers per hour If the value you input was in miles it will show miles per hour Note that the watch does not have a setting for specifying kilometers or miles e The average speed is indicated as a value from 0 to 350 in increments of 10 The ones digit is rounded off e Either of the following will cause the stopwatch second hand to indicate OVER which indicates that speed cannot be calculated When the speed calculation produces a value greater than 350 When a displayed elapsed time or cumulative elapsed time is 60 minutes or greater When a displayed lap time is 60 minutes or greater Average speed calculation will resume when timing of the next lap is performed OVER Indication To specify a course or section distance 1 In the Stopwatch Mode hold down for about three seconds until the center dial hand moves to DIST e This is the distance setting mode 2 Use and to specify the course or section distance e Use to move the stopwatch second hand and specify the value to the left of the decimal place You can specify a value from 0 to 14 Stopwatch second hand Distance value left of the decimal point g e Use to move the upper right dial hand and specify Distance the value to the right of the decimal place You can aA vate m specify a value from 0 0 to 0 9 right or e e It makes no difference whether the value you specify point represents kilometers or miles 3 Press to exit the setting sc
9. ment e You can restart and stop elapsed time measurement as many times as you like by pressing e The center dial hand rotates during the first 60 seconds only and then stops When elapsed time measurement is stopped by pressing the center dial hand jumps to the 1 20 second indication which is kept internally e Stopping a timing operation will cause the stopwatch second hand to stop at the elapsed time seconds position It will remain there if there is no distance value input If a distance value is input the stopwatch second hand will then move to average speed indication after about two seconds After that it will move back to the elapsed time second position e After you are finished measuring elapsed time press to reset the stopwatch to all Zeros e To return to the Timekeeping Mode press while the stopwatch is reset to all zeros Setting the year units digit 5 After the year setting is the way you want press e This will cause the watch to beep and change to the month setting mode 6 Use to move the stopwatch second hand clockwise to the month you want to specify To set March for example move the hand to 3 Mar Stopwatch second hand Setting the Month Operation Guide 5057 To start an elapsed time operation while in the Timekeeping Mode 1 In the Timekeeping Mode press to start elapsed time measurement e Elapsed time measurement will start internally when you press but timin
10. nce you set the date there should be no reason to change it except after you have the watch s battery replaced The date will change automatically when the current time reaches midnight The date change at the end of a month may take more time than normal Day of week To set the time and date 1 In the Timekeeping Mode hold down for about three seconds until the watch beeps e The stopwatch second hand and center dial hand will move to 12 o clock and stop there This is the setting mode Use and to change the time hour and minute setting e As you set the time take care to ensure that the 24 hour hand also is at the correct position After the time setting is the way you want press e This will cause the watch to beep and change to the year setting mode Stopwatch second hand Minute hand Stopwatch You can use the stopwatch to measure elapsed time cumulative elapsed time and lap times You also can input the distance of the course or a particular segment of the course of the race you are watching That distance is used along with the elapsed time cumulative elapsed time or lap time measured by the watch to calculate and display the average speed for the course or segment e See Average Speed for more information e Never operate the stopwatch while operating a motor vehicle Doing so is very dangerous and can cause an accident e Entering the Stopwatch Mode causes the stopwatch
11. r about three seconds ununmneneeeweweweweee Timekeeping Use the Timekeeping Mode to set and view the current time and date Pressing in the Timekeeping Mode will cause the center dial hand to move to the current day of the week Press to return to normal timekeeping The watch also will return to normal timekeeping if you do not perform any operation for about two seconds Hour hand Minute hand 24 hour hand Center dial second hand Press 7 After the month setting is the way you want press e This will cause the watch to beep and change to the day setting mode 8 Use and to change the day setting e When setting the day the watch automatically will skip days 30 and 31 that are not included in the currently selected month If you can t select 30 or 31 when you want to check to make sure that the proper month is selected You can return to the time setting mode after configuring the day setting by pressing Pressing will cause the watch to beep twice 9 After all of the settings are the way you want and the day display is no longer changing press A This will cause the center dial hand to start moving again and the other hands to start moving from their current positions e You can press at any time during the above procedure to return to the Timekeeping Mode e The watch s built in full automatic calendar makes allowances for different month lengths and leap years O
12. reen e To disable speed display specify a distance value of 0 0 Upper right dial hand Alarm When the alarm is turned on the alarm sounds when the alarm time is reached e Whenever you enter the Alarm Mode the stopwatch Hour hand second hand will move to the ALM position The center dial hand will move to the alarm s current ON OFF status while the hour minute and 24 hour hands indicate the current alarm time setting e All of the operations in this section are performed in the Alarm Mode Stopwatch Minute second hand hand To set an alarm time 1 In the Alarm Mode hold down for about three seconds until the watch beeps and the center dial hand moves to ON alarm on e This is the setting mode Setting the alarm time causes the alarm to turn on automatically 2 Use and to change the alarm time setting e Each press of either button changes the setting by one minute 3 After setting the alarm time press to exit the setting mode e As you set the alarm time take care to ensure that the 24 hour hand also is at the correct position 24 hour hand Center dial hand Alarm Operation The alarm tone sounds at the alarm time for 10 seconds regardless of the mode the watch is in Alarm operations are performed in accordance with the Timekeeping Mode time e Pressing any button stops the alarm tone operation To toggle an alarm on and off In the Alarm Mode press to toggle the alarm setting indic
13. second hand the upper right dial hand and center dial hand to move to the 12 o clock position e You can start elapsed time measurement with the stopwatch while the watch is in the Stopwatch Mode or the Timekeeping Mode Upper right dial stopwatch minute hand Stopwatch second hand Hour hand Center dial hand 4 Use and to change the year setting You can set the year within the range of 2000 to 2099 e Use 8 to move the stopwatch second hand clockwise to the value of the tens digit that you want to specify To set 2012 for example move the hand to 10 e Use to move the center dial hand clockwise to the value of the units digit that you want to specify To set 2012 for example move the hand to 2 Stopwatch 00 Center dial stopwatch 1 20 second hand This hand rotates and indicates the second count during the first 60 seconds 70 60 50 Setting the year 10s digit Center dial e The display range of the stopwatch is 59 minutes 59 95 seconds e The stopwatch continues to run restarting from zero after it reaches its limit until you stop it e You can switch to another mode from the Stopwatch Mode only while the stopwatch is stopped and reset to all zeros To start an elapsed time operation while in the Stopwatch Mode 1 In the Timekeeping Mode press to enter the Stopwatch Mode 2 In the Stopwatch Mode press 8 to start elapsed time measurement 3 Press 8 to stop elapsed time measure
Download Pdf Manuals
Related Search