Casio casio 2707 User's Manual
Contents
1. Release and the message receiving appears to indicate that signal reception has started e Time calibration signal reception takes from two to six minutes Take care that you do not move the watch during this time After signal reception is complete the display of the Receive indicator watch changes to the Last Signal screen and the analog time of the watch is adjusted automatically e The receive indicator indicates that the calibration time reception attempt was successful Note To interrupt a receive operation and return to the Timekeeping Mode press If the receive operation is unsuccessful the message ERROR appears on the display for about one or two minutes After that the watch returns to the Timekeeping Mode You can also change from the Last Signal or ERROR screen to the normal timekeeping screen by pressing About the Receive Indicator The receive indicator shows the strength of the calibration signal being received For best reception be sure to keep the watch in a location where signal strength is strongest Even an area where signal strength is strong it takes about 10 seconds for signal reception to stabilize enough for the receive indicator to indicate signal strength e Use the receive indicator as a guide for checking signal strength and for finding the best location for the watch during signal receive operations The receive indicator remains on the display in all2. If you changed the digital time setting with the above steps the analog hands move at this time to match it Wait until the analog hands stop moving before you advance to the next step Hold down for about two seconds until the watch Receive indicator CASIO Alarm Mode Data Memory Mode a Stopwatch Mode Release and the message receiving appears to indicate that signal reception has started Time calibration signal reception takes from two to six minutes Take care that you do not move the watch during this time If the watch is indoors we recommend that you place the watch near a window to allow better signal reception After signal reception is complete the display of the watch changes to the Last Signal screen and the analog time of the watch is adjusted automatically Time Calibration Signal Reception This watch is designed to pick up a time calibration signal and update its time setting in accordance with the signal There are two different methods you can use to receive the signal Auto Receive and Manual Receive With Auto Receive the watch automatically receives the calibration signal three times each day and makes appropriate adjustments With Manual Receive you perform a specific button operation to receive the calibration signal Before performing a signal receive operation remove the watch from you wrist and position it as s
3. modes following reception of the time calibration signal and calibration of the watch s time setting The receive indicator does not appear if signal reception was unsuccessful or after manual adjustment of the current time setting USER S GUIDE 2707 About Auto Receive When auto receive is turned on the watch automatically starts to receive the time calibration signal when the digital time in the Timekeeping Mode reaches 2 00 AM 4 00 AM and 6 00 AM each day calibration times Note The auto receive operation is performed only if the watch is in the Timekeeping or World Time Mode when one of the calibration times is reached It is not performed if a calibration time is reached while you are making settings while settings are flashing on the display while an alarm is sounding or while a silent alert operation is being performed e Auto receipt of the calibration signal is designed to be performed early in the morning while you sleep provided that the digital time is set correctly Before going to bed for the night remove the watch from your wrist and put it in a location where it can easily receive the signal e The receive indicator indicates that either the 2 00 AM 4 00 AM or 6 00 AM calibration signal reception was successful Note however that the receive indicator is cleared from the display at 3 00 AM each day If you do not see the receive indicator except for the above reason it means there was some probl
4. you are inputting text the cursor will jump to the first leftmost character of the text when you press instead of advancing to the right 4 Press to store your data and return to the data memory record screen without the cursor The message SAVE appears for about two seconds followed by a data memory record screen which shows the text you just input in the upper part of the display and a record number automatically assigned by the watch in the lower part of the display While the record number is in the lower part of the display you can see only six characters of the text in the record You can scroll through the text on the screen by pressing See To recall data memory records for more information Record number To recall data memory records 1 In the Data Memory Mode press to scroll forward through data memory records Each press of advances to the next record and shows its record number and first six characters of its text Pressing while the last record in memory is on the display changes to the remaining memory screen Pressing again displays the first record 2 Press to scroll through the text on the screen End mark z LTD N y First six characters Pressing scrolls through the text An end mark indicates the end of the text To edit a data memory record 1 In the Data Memory Mode display the record you want to edit 2 Press and the fla
5. 30 02 Use to change the setting 12 24 Hour format Hour Minutes 4 Press to exit the setting screen The auto receive setting is used for time calibration signal reception only See About Auto Receive for details See City Code Table for a complete list of available city codes e Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1 In the range of 00 to 29 the seconds are reset to 00 without changing the minutes Analog Timekeeping The analog time of this watch is synchronized with the digital time The analog time setting is adjusted automatically whenever you change the digital time Note The hands for the analog timepiece move to adjust to a new setting whenever any of the following occurs When you change the digital time setting manually When the digital time setting is changed by time calibration signal reception When you change the Home City code and or DST setting If the analog time does not match the digital time for any reason use the procedure described under To adjust the analog time to match the analog setting to the digital setting Whenever you need to adjust both the digital and the analog time settings manually make sure you adjust the digital setting first Depending on how much the hands have to move in order to adjust to the digital time it may ta
6. FORT WORTH MONTREAL DETROIT MIAMI BOSTON NYC NEWYORK 5 PANAMA CITY HAVANA LIMA BOGOTA CCS CARACAS 1 LA PAZ SANTIAGO PORT OF SPAIN SAO PAULO BUENOS AIRES BRASILIA RIODE JANEIRO 3 a 1 PRAIA DUBLIN LISBON CASABLANCA DAKAR LONDON ABIDJAN PARIS MILAN ROME MADRID AMSTERDAM ALGIERS BERLIN HAMBURG FRANKFURT VIENNA STOCKHOLM ATHENS HELSINKI ISTANBUL BEIRUT DAMASCUS CAIRO CAPE TOWN JERUSALEM JEDDAH KUWAIT RIYADH ADEN ADDIS ABABA NAIROBI MOSCOW TEHRAN 35 SHIRAZ DUBAI 04 ABU DHABI MUSCAT KBL KABUL 45 KHI KARACHI 05 DEL DELHI 5 5 MUMBAI KOLKATA DAG DHAKA 06 COLOMBO RGN YANGON 46 5 BKK BANGKOK 07 JAKARTA PHNOM PENH SINGAPORE KUALA LUMPUR BEIJING TAIPEI HKG HONGKONG 08 MANILA PERTH ULAANBAATAR TYO TOKYO og PYONGYANG SEL SEOUL ADL ADELAIDE 29 5 DARWIN SYD SYDNEY 10 MELBOURNE GUAM RABAUL NOU NOUMEA 11 PORT VILA WLG WELLINGTON 12 CHRISTCHURCH NADI NAURU ISLAND Based on data as of December 2001 Character List
7. USER S GUIDE 2707 General Guide Press to change from mode to mode In any mode press to illuminate the display World Time Mode Press Timekeeping Use the Timekeeping Mode to set and view the current time and date In the Timekeeping Mode press to change the screen format as shown below Timekeeping Mode Analog Seconds Date and Time Day of week Month y Press Pressing displays the Last Signal screen date and time the time calibration signal was last received in the Timekeeping Mode Receive date Receive time Last Signal Screen Current Time Setting This watch automatically adjusts its time setting in accordance with a time calibration signal You can also perform a manual procedure to set the time and date when necessary Before using the watch in Western Europe first use the procedure under Setting Up the Watch for Use in Western Europe to set the time in accordance with a time calibration signal Note that after you set your Home City the city where you normally use the watch code you must also turn on the watch s time calibration signal receiver if you want to enable auto time calibration See About Auto Receive for more information See Setting the Digital Time and Date Manually for information about manual settings The analog time of this watch is synchronized with the digital time Because of this the analog ti
8. ed 4 Press to exit the setting screen The minute hand will be adjusted slightly to match the seconds when you exit the setting screen To return to the Timekeeping Mode press World Time World Time shows the current time in 30 cities 29 time zones around the world e For full information on city codes see the City Code Table The current time for all city codes in the World Time Mode is calculated in accordance with the Greenwich Mean Time GMT differential for each city based on the your Home City time setting All of the operations in this section are performed in the World Time Mode which you enter by pressing GMT differential coda Current time in the selected city code To view the time in another city code While in the World Time Mode press to scroll through the city codes time zones to the east to scroll to the west If the current time shown for a city is wrong check your Timekeeping Mode time and Home City settings and make the necessary changes To toggle a city code time between standard time and Daylight Saving Time 1 In the World Time Mode use and to display the city code time zone whose standard time Daylight Saving Time setting you want to change TILON 2 Press to toggle Daylight Saving Time DST displayed and standard time DST displayed anton The DST indicator is on the display whenev
9. em with the calibration reception operation Either perform reception manually or make sure the watch is set up properly to receive the time calibration signal for the next automatic reception time When auto receive is turned on the watch receives the calibration signal for two to six minutes each day when the digital time reaches 2 00 AM 4 00 AM and 6 00 AM Do not operate of the watch s buttons within six minutes prior to or following the calibration times Doing so can interfere with correct calibration Remember that reception of the calibration signal depends on the time shown on the digital display The receive operation will be performed whenever the digital display shows 2 00 AM 4 00 AM and 6 00 AM regardless of whether or not the displayed time is actually the correct time When two or three receptions are successful the watch uses the data of the last reception for calibration When only one reception is successful the watch uses the data of the successful reception To turn auto receive on and off 1 In the Timekeeping Mode press This causes the current auto receive on off setting the receive indicator to flash which indicates the setting screen 2 Press to toggle auto receive on ON and off OFF 3 Press to exit the setting screen Setting the Digital Time and Date Manually Make sure you select your Home City code the city code whose time and date you are setting before change the c
10. er you display a city code for which Daylight Saving Time is turned on Note that the DST Standard Time setting affects only the currently displayed city code Other city codes are not affected Daylight Saving Time DST advances the time setting by one hour from Standard Time Remember that the not all countries or even local areas use Daylight Saving Time e Note that you cannot use the World Time Mode to change the DST ON OFF setting of the Home City code you currently have selected in the Timekeeping Mode The watch will perform a signal receive operation even if it is the World Time Mode when a calibration time is reached If this happens the World Time Mode time settings will be adjusted in accordance with the Timekeeping Mode s Home City code time CASIO Alarms Alarm on indicator Alarm screen name ALARH 1 onn USER S GUIDE 2707 The Alarm Mode gives you a choice of four one time alarms and one snooze alarm You can select either an audible beeper or flashing silent alert to let you know when any of the alarm times is reached You can also input reminder text that appears when the alarm time is reached Also use the Alarm Mode to turn the Hourly Time Signal on and off All of the operations in this section are performed in the Alarm Mode which you enter by pressing Alarm time Alarm name indicator To display Alarm Mode screen In the Alarm Mode use to cycle throug
11. factors as changes in the reflectivity of the ionosphere as well as movement of the ionosphere to higher altitudes due to seasonal atmospheric changes or the time of day may change the reception range of the signal and make reception temporarily impossible Think of the watch as acting like a TV or radio when it is receiving the calibration signal When receiving indoors move to a location as near as possible to a window Proper signal reception can be difficult or even impossible under the conditions listed below Near TVs refrigerators computers or other household appliances Far away from broadcasting stations among ferro concrete structures or near mountains Underground in tunnels or in ferro concrete buildings Near high tension wires neon signs or radio stations with interfering frequencies Near railroads highways or airports In trains or cars Radio interference can make signal reception impossible Strong electrostatic charge can result in the wrong time being set e If you are an area where proper time calibration signal reception is impossible the watch keeps time within 15 seconds a month at normal temperature Auto Summer Time DST Switching The time calibration signal transmitted from Mainflingen Germany includes both standard time and summer time Daylight Saving Time data When auto summer time DST switching is turned on the watch switches between standard time and summer time DST automatical
12. h the alarm screens as shown below ALARM1 gt ALARM2 H ALARMS gt ALARM4 SNOOZE gt SIGNAL 1 Alarm1 The following alarm screen names appear in the center Alarm2 2 of the display to indicate the alarm whose screen is currently displayed Alarm3 g ALARM1 through ALARM4 One time alarm screen Alarm4 SNOOZE Snooze alarm screen SIGNAL Hourly Time Signal screen The currently displayed alarm screen is also indicated by the alarm name indicators along the bottom left of the watch s display To set an alarm 1 In the Alarm Mode use to select the alarm whose time you want to set 2 Press and the hour setting of the alarm time starts to flash which indicates the setting screen Pressing and at the same time resets the alarm time to 12 00 AM and clears the reminder text in the upper part of the display if there is any 3 Press to move the flashing in the sequence shown below to select other settings Hour gt Minutes gt Text Selecting the text causes the text input cursor to appear You can input up to eight characters of reminder text for each alarm There are eight spaces in the text so you have to press eight times to move to the Hour setting 4 When the setting you want to change is selected use and to change it While the hour or minute setting is flashing use and to change it e When setti
13. hown in the illustrations below If your watch has a resin band pass the end of the band through the band loop and place the watch on a stable surface Resin band Metal band Pass through band loop If you are using the time calibration signal to set the time for this watch be sure to correctly set your Home City Otherwise there is the chance that the watch will not set the correct time Note that signal reception is possible only when the watch is within range of a time calibration signal transmitter and BER PAR LON or ATH is selected as the Home City code See City Code Table for a complete list of available city codes The current time setting in accordance with the time calibration signal takes priority over any time settings you make Auto receive is turned on when the watch is shipped from the factory Time calibration signal reception is disabled while the analog hands are moving after you change the digital time setting See the information under Time Calibration Signal Reception if you experience problems with time calibration signal reception To perform manual time calibration signal reception 1 Place the watch on a stable surface so its top 12 o clock side is facing in the general direction of the signal transmitter Note that signal reception is poor if the watch is on its back or side 2 In the Timekeeping Mode hold down A for about two seconds until the watch beeps
14. ilometers southeast of Frankfurt Signal reception is possible within the area represented by a circle with a radius of about 1000 kilometers At distances further than about 500 kilometers the signal may become weak and reception may be impossible under certain conditions Signal reception may be poor in the shaded area on the map even though it is within 1 000 kilometers of the signal transmitter Signal reception is affected by weather atmospheric conditions and seasonal changes This watch is designed to receive the signal transmitted from Mainflingen This means that reception is best when the antenna built into the 12 o clock edge of the watch is facing towards Mainflingen Note however that moving the watch while the time calibration signal receive operation is taking place will make stable reception impossible The watch is designed to automatically update the date and day of the week for the period January 1 2000 to December 31 2039 Setting of the date by the time calibration signal cannot be performed starting from January 1 2040 This watch can receive signals that differentiate between leap years and non leap years Even when the watch is within the reception range of the transmitter signal reception is impossible if the signal is blocked by mountains or other geological formations between the watch and signal source The time calibration signal is bounced off the ionosphere Because of this such
15. ke some time before the analog hands stop moving To adjust the analog time 1 In the Timekeeping Mode press five times to enter the Hand Setting Mode BH SET 2 Press and the current digital time starts to flash which indicates the setting screen 3 Use to adjust the analog setting as described below amp Current time When you want to do this Perform this button operation Move the hand setting Press O forward 20 seconds Move the hand setting back Press 20 seconds Move the hand setting a short Hold down way forward at high speed Release when the hands reach the setting you want Move the hand setting a Hold down short way back at high speed Release when the hands reach the setting you want Move the hand setting a While holding down 0 to move the hands at long way forward at high high speed press to lock the high speed speed hand movement Press any button when the hands are close to the setting you want Hand movement stops automatically if the hour hand makes one full 12 hour revolution While holding down to move the hands at high speed press 0 to lock the high speed hand movement Press any button when the hands are close to the setting you want Hand movement stops automatically if the hour hand makes one full 12 hour revolution Move the hand setting a long way back at high spe
16. ly in accordance with the calibration signal Daylight Saving Time DST advances the time setting by one hour from Standard Time Remember that not all countries or even local areas use Daylight Saving Time When using the watch within the reception range of the Mainflingen transmitter and BER PAR LON selected as the Home City code select AUTO DST to turn on the auto summer time setting The default auto summer time setting is AUTO DST whenever you select BER PAR LON or ATH as your Home City code e If you experience problems receiving the time calibration signal in your area it is probably best to turn off auto time switching To select the auto summer time setting 1 In the Timekeeping Mode press This causes the current auto receive on off setting the receive indicator to flash which indicates the setting screen 2 Press twice until the summer time DST setting screen appears 3 Use to cycle through the summer time settings in the sequence shown below AUTO CSTR OST 4 When the setting you want is selected press to exit the setting screen Troubleshooting Check the following points whenever you experience problems with your watch Problem Probable Cause What you should do Cannot perform The watch is not in the Timekeeping Mode Enter the Timekeeping Mode manual receive and try again Auto receive is You changed the time setting manually e Pe
17. me setting is automatically adjusted whenever you change the digital setting See Analog Timekeeping for more information Setting Up the Watch for Use in Western Europe You need to make the following three settings before using this watch in Western Europe The following provides a general overview of the setting procedure For full details see Setting the Time and Date Manually and Time Calibration Signal Reception e Specify the city code for your Home City the city where you will normally use the watch Select the auto summer time DST setting Perform the manual time calibration signal receive operation to set the current time To set up the watch for use in Western Europe P 1 In the Timekeeping Mode press 8 This causes the GMT differential City code current auto receive on off setting the receive indicator to flash which indicates the setting screen Press to move the flashing to the city code setting Use and to select the city code you want to use as your Home City The following are the city codes for major cities in the Western Europe time zones BER and PAR Berlin Paris Milan Rome Amsterdam Hamburg Frankfurt Vienna LON London Press to display the summer time DST setting screen Use to select AUTO DST AUTO DST specifies auto switching between Daylight Saving Time and Standard Time Press to exit the setting screen
18. ng the alarm time using the 12 hour format take care to set the time correctly as a m no indicator or p m P indicator When inputting text use and 0 to cycle through characters at the current cursor location and to move the cursor to the right See Inputting Text for more information 5 Press to exit the setting screen e If you input reminder text the text appears in place of the alarm screen name when you exit the setting screen e If the reminder text has more than six characters it will scroll from right to left whenever it is displayed Alarm Operation The following table describes the different types of alarm operations that this watch can perform Alarm Operation Type Alarm on indicator Description Alarm off Nothing happens when the alarm time is reached Alarm on The alarm on indicator and alarm name indicator flash on the display for 10 seconds The watch beeps for 10 seconds Alert on The alert on indicator and alarm name indicator flash on the display Snooze for 10 seconds indi rt indicator The watch does beep Press any button to stop the alarm after it starts to sound e If any alarm operation one time alarm silent alert snooze occurs while a signal receive operation is in progress the receive operation is canceled In the case of the snooze alarm the alarm operation repeats up to se
19. not displayed The Hourly Time Signal on indicator SIG is shown on the display in all modes while this function is turned on Data Memory You can use the watch s data memory to store e mail addresses Web page URLs and other text data All of the operations in this section are performed in the Data Memory Mode which you enter by pressing Remaining memory RESTIOOA x To create a new data memory record 1 In the Data Memory Mode press and at the same time to display the remaining memory screen You do not have to perform the above step if the RESTO remaining memory screen is already on the display If REST 0 is shown for remaining memory it means that memory is full To store another record you will first have to delete some of the records stored in memory 2 Press and the flashing cursor appears on the Cursor display which indicates the setting screen 3 Use and to cycle through characters at the ib current cursor location and to move the cursor to a the right See Inputting Text for more information Data Memory Records Each data memory record can contain up to 63 characters Records are stored in memory in the sequence they are created The number of records you can store in data memory depends on the number of characters that make up each record See Data Memory Management for more information If memory becomes full while
20. rform manual signal receive turned on but e The watch was not in the Timekeeping or wait until the next auto the receive or World Time Mode or you were signal receive operation is indicator does performing some button operation porformed Siete not appear on during the auto signal receive operation is ina location where it can the display was performed i i receive the signal Even if receive is successful the receive A Put the watch in a location indicator disappears every day at 3am that is suitable for good reception Time setting is e If the time is one hour off the DST setting e Change the DST setting to incorrect may be incorrect AUTO DST following signal The Home City Code setting is Select the correct Home City reception correct for the area where you are using Code the watch Timekeeping The day of the week is automatically displayed in accordance with the date year month and day settings The year can be set in the range of 2000 to 2039 The watch s built in full automatic calendar automatically makes allowances for different month lengths and leap years Once you set the date there should be no reason to change it except after you have the watch s battery replaced The current time for all city codes in the Timekeeping Mode is calculated in accordance with the Greenwich Mean Time GMT differential for each city based on the yo
21. shing cursor appears on the display 3 Press to move the flashing to the character you want to change 4 Use and to change the character 5 After making the changes you want press to store them and return to the data memory record screen To delete a data memory record 1 In the Data Memory Mode display the record you want to delete 2 Press and the flashing cursor appears on the display 3 Press and at the same time to delete the record The message CLEAR appears to indicate that the record is being deleted After the record is deleted the cursor appears on the display ready for input 4 Input data or press to return to the remaining memory screen USER S GUIDE 2707 Stopwatch The stopwatch lets you measure elapsed time split times and two finishes The display range of the stopwatch is 23 hours 59 minutes 59 99 seconds ipl The stopwatch continues to run restarting from ODODE TH zero after it reaches its limit until you stop it amp Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement The stopwatch measurement operation continues even if you exit the Stopwatch Mode All of the operations in this section are performed in the Stopwatch Mode which you enter by pressing Seconds 1 100 second Hours Minutes To measure times with the stopwatch Elapsed Time Start Stop Re
22. sor to the right 3 Repeat steps 1 and 2 to input the rest of the characters you want See the Character List for information about the characters you can input Data Memory Management Data memory can hold up to 315 characters total while each record can contain up to 63 characters This means that 40 records can be stored in data memory when each record contains seven characters of text or less Backlight Precautions The backlight uses an EL electro luminescent panel that causes the entire display to glow for easy reading in the dark In any mode press 0 to illuminate the display for about one second The electro luminescent panel that provides illumination loses power after very long use The illumination provided by the backlight may be hard to see when viewed under direct sunlight The watch may emit an audible sound whenever the display is illuminated This is due to vibration of the EL panel used for illumination and does not indicate malfunction The backlight automatically turns off whenever an alarm sounds Frequent use of the backlight shortens the battery life CASIO USER S GUIDE 2707 CASIO City Code Table oy City Differential Other major cities in same time zone gt 11 PAGO PAGO HNL HONOLULU 10 PAPEETE ae SAN FRANCISCO LAS VEGAS VANCOUVER LAX LOSANGELES 8 SEATTLE DAWSON CITY DENVER 27 EL PASO EDMONTON ear GuieAGo 26 HOUSTON DALLAS
23. start Stop Clear Split Time 000 0 0 0 o o Start Split Split release Stop Clear SPL displayed Two Finishes 000 0 00 00 AOA Start Split Stop Split release Clear First runner Second runner Display time of finishes finishes second runner Display time of first runner Reference This section contains more detailed and technical information about watch operation It also contains important precautions and notes about the various features and functions of this watch Auto Return Features If you leave the watch in the Alarm Data Memory or Hand Setting Mode for two or three minutes without performing any operation it automatically changes to the Timekeeping Mode e If you leave a screen with flashing digits or a cursor on the display for two or three minutes without performing any operation the watch automatically saves anything you have input up to that point and exits the setting screen Data and Setting Scrolling The and buttons are used in various modes and setting screens to scroll through data on the display In most cases holding down these buttons during a scroll operation scrolls through the data at high speed Initial Screens When you enter the Alarm or World Time Mode the data you were viewing when you last exited the mode appears first Time Calibration Signal Reception This watch is able to receive the time calibration signal transmitted from Mainflingen Germany located 25 k
24. ur Home City time setting GMT differential is calculated by this watch based on Universal Time Coordinated UTC data The letters UTC stands for Universal Time Coordinated which is the world wide scientific standard of timekeeping It is based upon carefully maintained atomic cesium clocks that keep accurate to within microseconds Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth s rotation The reference point for UTC is Greenwich England 12 hour 24 hour Timekeeping Formats The 12 hour 24 hour timekeeping format you select in the Timekeeping Mode is also applied in all other modes e With the 12 hour format the PM indicator appears on the display for times the range of noon to 11 59 p m and the no indicator appears for times in the range of midnight to 11 59 a m e With the 24 hour format times are displayed in the range of 0 00 to 23 59 with 24 indicator Inputting Text The following describes how to input text in the Alarm and Data Memory Modes To input characters 1 When the cursor is on the display use and to cycle through the available letters numbers and symbols in the sequence shown below Press Press m atz m xtot space lower case symbol 009 AtoZ Reminder Text Input number 4 upper case Screen 2 When the character you want is at the cursor position press to move the cur
25. urrent time and date settings World Time Mode times are all displayed in accordance with the Timekeeping Mode settings Because of this World Time Mode times will not be correct if you do not select the proper Home City code before setting the time and date in the Timekeeping Mode To set the current digital time and date manually 1 In the Timekeeping Mode press This causes the current auto receive on off setting the receive indicator to flash which indicates the setting screen 2 Press to move the flashing in the sequence shown below to select other settings City Code 12 24 Hour Receive DST Format Seconds Day 4 4 Month k Year Minutes 4 Hour 3 When the setting you want to change is flashing use and or to change it as described below Setting Screen Button Operations Auto Receive AUTO ky Press to toggle auto receive on and off City code 1JEER Use and to change the setting DST Press to toggle between Daylight Saving Time ON and standard time OFF Pressing performs a different operation when BER PAR LON or ATH is selected as Home City Code See Auto Summer Time DST Switching Press O to toggle between 12 hour 12H and 24 hour 24H timekeeping Use to change the GBS setting Seconds Press to reset the seconds to 00 Month Day Year 6
26. ven times every five minutes until the alarm is turned off e If you input reminder text for an alarm the text appears for one minute in place the date on the Timekeeping Mode screen The text is cleared from the Timekeeping Mode screen if you change to another mode while it is displayed Alarm operations and the Hourly Time Signal operation are performed in all modes To test the alarm In the Alarm Mode hold down to sound the alarm To select the alarm operation type 1 In the Alarm Mode use to select the screen for the alarm ALARM1 to ALARM4 or SNOOZE whose alarm type you want to select 2 Press to cycle through the available settings in the sequence shown below CASIO The alarm on indicator Sau and alarm name indicator are displayed for each alarm 1 through 4 snooze for which alarm on is set The alert on indicator and alarm name indicator are displayed for each alarm 1 through 4 snooze for which alert on is set In other modes besides the Alarm Mode the alarm name indicator is displayed for each alarm for which alarm on is selected In all modes the alarm on indicator or alert on indicator is shown for any alarm ALARM1 through ALARM4 or SNOOZE that is currently turned on To turn the Hourly Time Signal on and off 1 In the Alarm Mode use to select the Hourly Time Signal SIGNAL SIGNAL 2 Press A to toggle it on SIG displayed and off SIG
Download Pdf Manuals
Related Search