Casablanca Fan Company S3 User's Manual
Contents
1. pole length is not long enough and inside blade is too close to downslope or side wall Extending pole length will usually solve problem Calculation of 32 Use the tear off Ceiling Angle Template inserted the 4 back of this manual it provides you with a simple go or no go for installing your fan on a sloped ceiling EXAMPLE 1 This slope is less than 32 It is OK to install your fan EXAMPLE 2 This slope is 32 This is the maximum slope that will allow the fan to hang straight down It is OK to install your fan EXAMPLE 3 This slope is more than 32 Your fan will not hang straight down an adaptor is necessary Contact your local Authorized Casablanca Dealer in regards to purchasing a Slope Ceiling Adaptor 53 INSTALLATION INSTRUCTIONS Unpacking Before assembling and installing your ceiling fan remove all parts from the shipping cartons and check them against the parts listed here Before discarding packaging material be certain that all parts have been removed WORK BENCH SETUP Setup Remove the bottom foam from the box and place the fan rightside up in the foam This protects the lamp socket during assembly NOTE If this is the second Versa Touch fan in stalled in the same area one of the fans MUST have its channel changed Please refer to the Versa Touch section the bottom of page 92. 84 CIRCUIT BREAKER TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON Never insert anything into the path of the fan blades while the fan is in operation CAUTION MOUNT WITH THE LOWEST MOVING e Never install fan over a pool or spa ao PARTS AT LEAST 2 5 METRES ABOVE FLOOR OR e Never operate a fan that has been damaged GRADE LEVEL in any way Contact Casablanca Fan Company ATTENTION INSTALLER DE SORTE QUELES by calling toll free 1 888 227 2178 or eee PIECES INFERIEURES SOIENT A AU MOINS 2 5 contact your local authorized Casablanca dealer for assistance in obtaining service METRES AU DESSUS DU PLANCHER OU DU SOL P N 9343010 REV B APR01PDG ay FAN COMPANY MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan read the following helpful recommendations The location of the fan air circulation and fan size are all important factors to consider before installation Location Ceiling fans have practical uses in almost every room in your home We suggest you follow these mount mg recommendations as you decide where to Install your Casablanca fan For safety reasons the fan blades must be a minimum of 7 above the floor Do not locate the fan in a doorway or above a swinging door sufficient clearance for the blades In bedrooms fans work best when mounted above the foot of the bed pool tables be sure to
3. Step 1 Remove the two screws holding the switch cover plate Do not remove the cover plate Step 2 Orient the control holder as shown and line up the two inner mounting holes with those the switch mounting holes with those on the switch Step 3 Install and tighten screws by hand only Step 4 Install and tighten screws by hand only VERSA TOUCH STORING CONTROL IN HOLDER Step 1 Break off the two tabs by pushing outward Step 2 Remove the two screws holding the switch cover plate Do not remove the cover plate Step 3 Orient the control holder as shown and line up the two outer Wall Installation Step 1 Locate a 2X4 wall stud in a convenient loca tion Step 2 Orient the control holder as shown over the 2X4 stud Step 3 Use the 1 wood screws in ei ther the inner or outer mounting holes Install and tight en screws by hand only um WooD SCREW 1 VERSA TOUCH BATTERY INSTALLATION Note The wall anchors and 6 32 x 1 screws may be used in situations where mounting to a stud is not possible Use the inner mounting holes After securing the anchor dis card the pointed screws and use the 6 32 de cor ovalhead screws supplied ANCHOR PANHEAD SCREW DRYWALL ANCHOR DECOR OVALHEAD SCREW 6 32 X1 Control Storage Angle control in top first in the holder until the unit can be gently pushed back and snapped onto the bottom
4. must be installed Casablanca extension poles are available for sloped or high ceiling installations e This ceiling fan requires a grounded electrical supply of 120 VAC 60 Hz and a minimum 15 amp circuit The maximum current requirement for the fan with light fixture is 3 8 amps The fan uses about 1 amp or 100 watts Maximum light current is 2 8 amps or 340 watts of lighting Where wire nuts are employed be sure all bare wires are within the connectors When installing the canopy hatch make sure all wires are within the canopy and that no wires are being pinched For best performance and for your warranty to be valid use only genuine Casablanca blades light fixtures and accessories e The blades in each pack are matched for equal 1 lo p FUSE BOX REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON weight to assure smooth fan operation If more than one fan is being installed be careful not to mix blades from different cartons Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer e t is always good idea to have an assistant to help with the installation e When cleaning painting or working near your fan be very careful of the fan and blades Always turn the power OFF to the ceiling fan before servicing it working on it or replacing light bulbs
5. provide plenty of clearance to avoid damage from pool cues kitchens be sure to allow for open cupboard doors to clear the fan blades Do not install a fan close to or over a pool or spa High humidity combined with corrosive gases will destroy the finish and warp the blades Fan Size Variable fan speed capability permits the use of a full size 52 fan even in smaller rooms For very large rooms two fans may be needed In any installation the tips of the blades must be at least 18 from the wall in order to provide SLOPED CEILING INSTALLATIONS Suggested Extension Pole Lengths Ceiling Height Pole Length EXTENSION 8 Standard POLE Standard m MAXI MUM HANG TRU ANGLE 322 gt BLADES MUST BE A When to Use Extension Poles LJ For best performance and best appearance MINIMUM OF 7 ABOVE THE FLOOR 7 MINIMUM an extension pole should be used with your Casablanca fan when installing on gt high cathedral ceilings or sloped ceil ings Casablanca offers standard poles in f increments of 6 up to 5 Custom poles are available lengths up to 10 See your gt Authorized Casablanca Dealer for details Note Fan may wobble or vibrate if TI 1
6. rim GOES Removing Gently Pull the lower edge of the control gently out from the holder Remove Battery Door Turn control on its front Twist a coin to unsnap the door A Lift door away from control B and remove C 4 QI eS SNAP PLUG SOCKET Install Battery shown Observe proper polarity Replace the battery door Press battery into control aligned as Changes or modifications not expressly approved in writing by Casablanca Fan Co may void the user s authority to operate this equipment VERSAeT OUCH VERSA TOUCH OPERATION SEND SIGNAL Fan Control To start the fan Press the selected speed button to run the fan at the desired speed LO Low speed er MED LED Medium speed lt gt HI High speed turn off the fan Press the FAN OFF button Airflow Direction Ee To reverse the airflow press the REVERSE button Reverse operates at any speed whether fan is FAN OFF on or off The fan returns to its set speed after reversing Light Control a Turn the light on or off independently from the fan by pressing the LIGHT button Keep pressing the button in excess of 0 7 seconds it becomes a dimmer The light varies from bright to dim over approximately 8 seconds This sequence will reverse the light when it reaches the brightest or dimmest level if you continue to hold the LIGHT butt
7. HER WIRE APPROVED OUTLET BOX HARDWARE CANOPY HARDWARE CANOPY SCREW 4 CANOPY HATCH O CANOPY LOCK WASHER 4 CANOPY INSTALLATION Step 2 Attach the canopy to the crossbar mount ing bracket with three of the 8 32 x 244 long canopy screws and canopy lock washers Tighten the screw firmly by hand only CROSSBAR MOUNTING BRACKET Note On sloped ceilings align the canopy opening towards the top or 22 4 CANOPY LOCK WASHER CANOPY SCREW BLADE HARDWARE a P lt Y BLADE INSTALLATION Step 3 Assemble the blades to the motor using the 3 blade screws and 3 metal washers Hand tighten firmly BLADE SCREW amp WASHERS As ane Step 4 To hang the fan body in the canopy hold the fan body firmly and in sert the ball into the canopy opening Check that no wires were pinched Ro tate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening NOTE The fan weight is 23 pounds BALL CANOPY ELECTRICAL CONNECTIONS Step 5a Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut Test that the connection is secure by pulling on the wire nut Connect in this order Step 5b Wiring Connections GREEN leads from mounting plate and fan to GROUND con
8. LIGHT NOT DIM Defective receiver Replace Receiver NO REVERSE Defective receiver Replace Receiver FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED Check antenna wire is not touching metal plate FAN STARTS WORKING BY ITSELF Frequency interference Change frequency as described on Page 9 For questions or to locate the nearest Casablanca Authorized Service Center call toll free 1 888 227 2178 or visit us on the web at www CasablancaFanCo com L This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 This equipment has been tested and found to comply with the limits for a Class digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by on
9. S3 OWNER S MANUAL CONTENTS INTRODUCTION i ea a ea eae Ba a ee aa SG 1 MOUNTING RECOMMENDATIONS 2 FAN INSTALLATION cae de mean cay mate go 3 CONTROL FEATURES VERSA TOUCH OPERATION 9 TROUBLESHOOTING ane ele oie ee Peo 10 SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation therefore before attempting to install and operate your Casablanca fan read this owner s manual completely and carefully Retain this manual for future reference CAUTION To avoid possible electrical shock make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure BEFORE YOU START All wiring must be in accordance with the National Electric Code ANSI NFPA 70 1993 and the appropriate local electrical codes The National Electric Code requires proper grounding as a precaution against electrical shock A qualified electri cian should be consulted if you are unsure e This fan is designed to be installed on an existing electrical outlet box The outlet box must be UL Listed for ceiling fan installations if it is not a new box
10. Touch fan s 1 HI as you may inadvertantly change the frequency settings for 2 MED it as well 3 LO VERSA TOUCH IF FAN DOES NOT WORK If the fan is not functioning after installation Lo MED HI Step 1 Check to make sure that batteries are installed correctly in the control Step 2 Turn the power off to the fan from the circuit breaker 3 2 1 for at least 5 seconds Z PRESS IN THIS ORDER TO SET NEW Step 3 Turn the power back on at the circuit breaker and push FREQUENCY the Hi Med and Low buttons in that order within 20 seconds 1 HI Step 4 The fan should now function properly paie 2 FAN COMPANY TROUBLESHOOTING Before Requesting Service Please follow this troubleshooting guide before contacting your dealer for assistance Caring for Finishes For cleaning a soft brush or lint free cloth should be used to prevent scratching the finish A vacuum cleaner brush nozzle can remove heavier dust Surface smudges or an accu mulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth An antistatic agent may be used but never use abrasive cleaning agents These will damage the finish Painted and high gloss blades may be cleaned in the same manner Blades Wood finish blades should be cleaned with a furniture pol ishing cloth Occasionally a light coat of furniture polish may be applied for added p
11. WORK BENCH PERMA LOCK HARDWARE DOWNROD amp BALL ASSEMBLY ALLEN SET SCREW Ya 20 x Ya PRE INSTALLED 3mm ALLEN WRENCH FAN PREPARATION IMPORTANT SAFETY INFORMATION 7 BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN INSTALL THE MOTOR THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY WIRES Prepare for fan installation as follows Step A Route the wires from the motor through the PermaeLock downrod and ball assembly Tip The downrod has a tapered thread Pe eA that is designed to lock completely when ASSEMBLY correctly installed Step B Using the provided allen wrench loosen the set screw TAPERED several turns to allow installation of the downrod Thread the downrod into the motor coupling until it stops turning this will take at least four and a half full turns MOTOR ALLEN PLIN SET SCREW 6 ow 9 Step Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan CAUTION Failure to fully lock in the down rod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation y a FAN CEILING HARDWARE ADDITIONAL HARDWARE 21 x 8 32 ROUND HEAD CROSSBAR wi SeRews 2 8 32 ROUND BRACKET Cp SCREWS 2 FLAT WASHER 2 GETTI NG STARTED Installing a New Ceiling Fixture Outle
12. ductor of power source Secure with wire nut 2 BLACK WIRES WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box Secure with wire nut BLACK power wire from fan to BLACK power wire in ceiling outlet box Secure with wire nut WIRE NUT 2 WHITE WI i 0 Step 6 Tuck the wires into the canopy with the wire nuts pointed upwards so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening Step 7 Install canopy hatch with the last canopy screw and lock washer To do this tilt the fan body away from the hatch opening Tighten the screws firmly by hand only Step 8 Straighten the fan then check to ensure that there is no movement be tween the canopy and ceiling or Hang Tru ball and top support shaft INSTALL BULB AND GLASS Step 9 Screw the 100 Watt Halogen bulb into the socket Do not touch the glass bulb with your fingers it is extremely important that the glass be clean If it is touched or dirty clean carefully with a tissue A dirty glass bulb will cause the bulb to fail almost immediately IMPORTANT When installing the halogen bulb care fully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket HALOGEN BULB 100 WATT Step 10 Position the indentations in the outer rim of the glass shade so that they line up with the tabs on th
13. e inside surface of the fan light fixture rim Step 11 Carefully lift the glass shade up inside the light fixture as far as it will go Step 12 Rotate the shade in a clockwise direction until it is held tightly in place by the three tabs GLASS SHADE INDENTATION SAVING MONEY WITH YOUR CEILING FAN IN SUMMER the movement of IN WINTER hot air rises to the air creates a cooling wind chill ceiling while cool air settles to the effect A room can actually feel floor Trapped against the ceiling several degrees cooler without set the warm air is wasted If you turn ting the thermostat lower up the thermostat energy costs will rise RUNNING IN REVERSE your Casablanca fan recirculate warm air near the ceiling down into the living area providing even heating and comfort with a pleas ant effect on heating bills VERSAel OUCH VERSA TOUCH INSTALLATION EN W42 HOLDER 0 2 0 DRYWALL woop SCREW SCREW W 42 T ANCHOR SCREW 6 32 X3 g 6 32 1 CONTROL D 9V BATTERY 6 32 1 2 2 2 2 SA TOUCH 9 CONTROL HOLDER INSTALLATION CAUTION Do not use with wall dimmer REMOVE TABS STANDARD TOGGLE TYPE SWITCH 8 LIGHT SWITCH INNER H MOUNTING HOLES SWITCH SWITCH COVER _ COVER PLATE l PLATE Rocker Light Switch Standard Light Switch
14. e or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one s authority to operate this remote control ANY 761 Corporate CENTER Drive Pomona 91768 Free 888 CASA 1ST 227 2178 www CasablancaFanCo com CopyriGHt 2000 Casablanca Fan Company U S PATENT PENDING PRINTED IN ROC
15. nger bracket and or ceiling outlet are loosely attached Make sure that the hanger bracket is tightly attached to the ceiling outlet box Make sure that the downrod assembly is secured firmly Downrod is loosely attached to downrod base Make sure that all screws are securely tightened FAN NOISY DURING eCheck and tighten light fixture retaining screws glass shade screws and or the light bulb s OPERATION Tighten canopy screws and mounting plate assembly Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices Tighten as necessary Tighten blade holders to flywheel or direct drive motor and blade to bladeholder screws sure all screws in the motor housing are snug but not overly tight Defective bulb Replace bulb DOES NOT RUN ON If new break in may be required run at higher speed for several days LOW SPEED BATTERY LIFE Not using Alkaline batteries Replace with Alkaline batteries SEEMS SHORT LIGHT 0 K NO FAN Pin connectors not making good contact check 9 pin connector under top cover FAN 0 NO LIGHT Defective receiver Replace receiver Defective motor Replace motor Broken socket Replace socket Defective receiver Replace Receiver FAN AND LIGHT ON FULL NO CONTROL Defective receiver Replace Receiver MISSING ONE SPEED Defective receiver ReplaceReceiver FAN DOESN T CHANGE SPEED LIGHT O K Replace receiver FAN O K
16. on Release the button when the desired level is reached Auto Resume Quick pressing less than 0 7 seconds on off operation of the LIGHT button maintains the desired brightness level set previously VERSA TOUCH CHANGING FREQUENCY SETTING You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately BACK Note All fans leave the factory set to 00000 VERSA TOUCH S Step 1 At the circuit breaker or fuse box turn the power off for the fan you want to change Step 2 Open the battery door of the Versa Touch control and remove the batteries Step 3 Change the dip switch settings assuring that they are different from the previously installed Versa Touch fan Step 4 Re install the batteries and the battery door on the control DIP SWITCH DIP SWITCH Step 5 At the circuit breaker or fuse box turn the power back on for SET 10000 SET TO 01001 the fan whose frequency you are changing Step 6 Within 20 seconds of restoring power push the Hi Med and Lo buttons in that order Note You may want to label your controls to assure you not mix them up WITHIN 20 SECONDS OF TURNING THE FAN ON PRESS IN THIS WARNING Do not turn the power off at the circuit breaker ORDER TO SET NEW FREQUENCY then back on for the previously installed Versa
17. rotection and beauty Never Lubricate this Fan The precision motor at the heart of your Casablanca fan features sealed bearings that are the motor Changing Light Bulbs Be sure to turn power to breaker before changing ubricated for life Do not attempt to oil the fan OFF at the wall switch or circuit ght bulbs Replace bulbs with same type as removed from the fixture Each fan is rated for a maximum TOTAL wattage of lighting Exceeding the rated maxi burn out the fan electron mum allowable wattage for the fan will ics module and void the warranty PROBLEM POSSIBLE REMEDIES FAN WILL NOT START main circuit fuses circuit breakers or wall switch position Check all wire connections making sure the power is turned off during this inspection connectors are not making good contact Check the connections in the switch housing and under the top cover Battery weak install fresh battery receiver defective replace eCheck the frequency setting Turn power off at the circuit breaker only for the fan not functioning for at least 5 seconds turn the power back on within 20 seconds press the Hi Med and Lo buttons in that order to set the frequency of the fan to the control See Page 9 FAN WOBBLES OR SHAKES sure canopy pin is properly set into the slot on the ball EXCESSIVELY eCheck that bladeholders have not been bent during installation and blades are balanced Ha
18. t Box If you do not have an existing fixture located where you wish to place your Casablanca fan an approved ceiling fixture outlet box must be installed and wired Warning To reduce the risk of fire electrical shock or personal injury mount to outlet box marked ac ceptable for ceiling fan support using the mounting hardware provided with the outlet box Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source either circuit breaker or fuse box lower the old fixture and disconnect the wiring Check the ceiling fixture outlet box to be sure that it is marked Approved for ceiling fan mounting If it is not a new box must be installed NOTE The fan weight is 23 pounds CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows Step 1 Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole Attach the bracket with ground wire and ridges down to the ceiling fixture out let box with the mounting hardware included with the outlet box Tighten the screws firmly by hand only being careful not to bend the bracket by over tightening CAUTION To reduce the risk of personal injury use only the mounting hardware provided with the approved outlet box to install CEILING FAN APPROVED WIRING BOX RIDGE SIDE DOWN CEILING WIRING CROSSBAR MOUNTING BRACKET the crossbar mounting bracket GREEN FLAT GROUND WAS
Download Pdf Manuals
Related Search