Casablanca Fan Company Marrakesh 89UXXM User's Manual
Contents
1. s long canopy screws and lock washers provided with your Casablanca fan Hand tighten until snug against the ceiling Note On sloped ceilings align the canopy opening toward the top or peak of the room CANOPY ne LOCK if WASHER f CANOPY SCREW FEED OUTLET BOX WIRES THROUGH CANOPY OPENING Blade Blade Iron Medallion Bracket 8 32 x 8mm Small Allen Wrench 3 3 3 3 12 Step 5 Take a blade blade iron bracket and 4 of the 8 32 screws Align the blade iron into the holes of the blade and then place a bracket edges facing up away from the blade and assemble with the 4 screws tighten securly by hand 3 FAN cert BLADE HOLDER MEDALLION AND BLADE ASSEMBLY Step 6 Align the medallion over the bracket with the set screw towards the edges of the blade and place the medallion over the wider end of the bracket When it feels engaged push on it until the other end snaps in place Step 7 Using the allen wrench tighten the set screw by hand until snug Step 8 Repeat step 5 through 7 until all 3 blade assemblies are complete Note Write down the Serial Number and the model number for future reference Step 9 Remove the motor sheild from the top of the motor note the caution message and read the instruction carefully p PLACE nee INSTAL PEN LAT VER p WHEN INSTALLA Tio W ay wer ae ls mi B MENTE THAT THE ALLEN FDEKSCHEN Co T TIGHTLY AGAINST THE2. sil e When cleaning painting or working near your fan be very careful of the fan and CIRCUIT BREAKER blades Always turn the power OFF to the TRIP BREAKER FOR THE ceiling fan before servicing it working on CIRCUIT YOU WILL BE it or replacing light bulbs WORKING ON e Never insert anything into the path of the mi fan blades while the fan is in operation HJ e Never install a fan over a pool or spa Poi e e Never operate a fan that has been damaged in any way Contact Casablanca Fan Company by a calling 1 888 227 2178 or contact your local i io authorized Casablanca dealer for assistance i asd in obtaining service PN 8943540 ATO708 Eisen Before mounting your Casablanca fan read the following helpful recommendations The location of the fan air circulation and fan size are all important factors to consider before installation Location Ceiling fans have practical uses in almost every room in your home We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan e For safety reasons the fan blades must be a minimum of 7 above the floor e Do not locate the fan in a doorway or above a swinging door e In any installation the tips of the blades must be at least 18 from the wall in order to provide sufficient clearance for the blades e In bedrooms fans work best when mounted above the foot of the bed e In low ceiling locations
3. 9 9 See Ca your Authorized Casablanca Dealer for F details Zia e NOTE Fan may wobble or vibrate if pole length is not long enough and EXAMPLE 1 This slope is less than 32 It is OK to install your fan EXAMPLE 2 inside blade is too close to downslope or side wall Extending pole length i roblem will usually solve proble This slope is 32 This is the maximum Slope that will allow the fan to hang straight down It is OK to install your fan EXAMPLE 3 Calculation of 32 This slope is more than 32 Use the tear off Ceiling Angle Template card inserted in the back of this manual it provides you with a simple go or no go for installing your fan on a sloped ceiling IMMAR RAKESH e INSTALLATION INSTRUCTIONS Unpacking Before assembling and installing your ceiling fan remove all parts from the shipping cartons and check them against the parts listed in instructions Before discarding packaging material be certain that all parts have been removed GETTING STARTED Carton Contents The fan carton contains the fan body warranty card owner s Be sure to use only genuine Casablanca blades The blade manual and all the parts necessary to assemble and install shrink wrap holds 3 blades of matched weight If more than your Casablanca ceiling fan These parts are shown at the one fan is being installed be sure not to mix blade sets start of each installation sec
4. CONTENTS INTRODUCTION 24 40 0 v 44 e644 64 idast nirt ee ee wea be ee Ge Seo e ee eee oak Se eee os 1 MOUNTING RECOMMENDATIONS sackdica a oo 665 455 8S 4S SWE SONS SOS ASS Be RE Se Owe eee 2 FANLINSTALUATION cicecet seus canes kerr oad se oe eee eee eee eee eA oe ee a ees oes 10 OPTIONAL EXCLUSIVE LIGHT FIXTURE INSTALLATION 2 2 2 ccc ccc cw cece cr ccc creer cence crn ecce 11 CONTROL FEATURES WERSACTOUCH 2 gas navsaenad d te abe SGee Ge ensei aoe ede oe nee see eee ae eee ade eee ees 14 IROUBLESHOOTING 465 He eaes Goa 5 O58 Ween Se Gee Ok Sea oe bes a eo ne Hee Vee oe ees 16 SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation therefore before attempting to install and operate your Casablanca fan read this owner s manual completely and carefully Retain this manual for future reference CAUTION To avoid possible electrical shock make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure e CAUTION RISK OF ELECTRICAL SHOCK All wiring must be performed in accordance with national and local electrical codes If you are unfamiliar with the wiring codes you should use a qualified electrician To avoid overheating and possible damage to other equipment do not install control to a receptacle fluorescent light fixture motor operated appliance or transformer supplied appliance
5. Check that the bladeholders have not been bent during installation and the blades are balanced The hanger bracket and or ceiling outlet are attached too loosely Make sure the hanger bracket is attached tightly to the ceiling outlet box and the downrod assembly is secured firmly The downrod is attached to downrod base too loosely Make sure all the screws are securely tightened Fan is noisy during operation e Check and tighten the light fixture retaining screws glass shade screws and or lightbulb s e Tighten the canopy screws and mounting plate assembly Make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices Tighten as necessary e Tighten the blade holders to the flywheel or direct drive motor and the blades to the bladeholder screws e Make sure all screws in the motor housing are snug but not overly tight Fan does not run on low speed e If fan is new it may need to be broken in Run at high speed for several days Battery life is short e Replace with alkaline batteries Light works but fan does not work e Pin connectors are not making good contact check 9 pin connector under top cover Fan and light run only on full speed e The fan receiver is defective Replace fan receiver Fan is missing one speed e The fan receiver is defective Replace fan receiver Fan does not change speed but light works e The fan receive
6. DOWNROD Wipy L THREADS AFTER FAN IS ASSEMI FAILURE TO DO SO WILL CAUSE THE FAN TO FALL DO NOT OIL SEALED BEARING WET MARKED FANS SUITABLE FOR USE a OUTDOOR LOCATIONS INSTALLED IN A GFCi PROTECTED BRANCI DAMP MARKED FANS SUITABLE FOR USE IN DAMP LOCATIONS WHEN INSTALLED IN A GFCI PROTECTED BRANCH USE UNDER A WEATHER PROOF STUCTURE INSTALLER INSTALLER GIVE THIS TAG TO THE COSUMER CONFIRM LOCKSCREW AFTER INSTALLATION IS COMPLETE IS PROPERLY TIGHTENED P N 85055 01 000 TEN LOCKSCREW OTINGOL T3 3L3l 0 10 SS088 Nd VLFTGNOD VLSI NOOVIVLSN V1 INO 3d ALNSNVIcOudY OdVLaucV SaNdS30 YOGIWNSNOD TW YLINOILI Y1S3 3d SLS3 OTINYOL 73 SND SWYIANOD WIVLSNI 13 YOQVIVLSNI Ta OHISL 30 VYNLINYLSS YNN Orva SSOGNVSN 1939 OLINDYID NN 30 NOIDOILOYd VI OVa SOCVIVLSNI uss Dal aa rae a peal Poa ore es VuVd SOGVOUVIN SOJINVEY 07 i NOISDSLOud V1 Orva SOGVIVISNI Yas N3830 Sua suv oy Svaanne ZQVGNVION VeVd SOCVIYVN SODINVaY S07 NOIDNVISud OTYVLNOM 30 S3anNdS3d0 VSIVD 3S YOOVILNSA 13 Sno vaysnvo OGVGNSWOI3Y 07 YSOVH 30 Viivs V1 unos 3G OTINYOL 73 3N0 30 OAILVUSdW 3 Se OUYDI Tad MOTOR SHEILD BLADE ASSEMBLY BLADEHOLDER SCREW 12 24 X 5 8 2 PER BLADE Step 10 Take a blade assembly and insert the foot of the blade iron between the m
7. R Step 16 Securely tighten the set screw with the provided COUPLING allen wrench to ensure safe operation of your fan CAUTION Failure to fully lock in the down rod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation FAN PREPARATION IMMAR RAKESH Step 17 Align the motor cover key hole slots with the three screws in the motor adapter Once the cover clears the screw and washers turn counter clockwise to engage Step 18 Securely tighten the screws by hand until snug KEY HOLE SLOT HANGING THE FAN HOUSE WIRING Step 19 To hang the fan body in the canopy hold the fan body firmly and insert the nylon ball into the canopy opening E Check that no wires were pinched Rotate the fan body until GROUND the slot in the nylon ball engages the canopy pin opposite the canopy hatch opening MOTOR WIRES amp DOWNROD GROUND Fan weighs 40 lbs iis CANOPY CANOPY PIN Step 20 Connect the fan wires to the outlet box wiring by placing the bare ends of the wires 2 WHITE together and then securing with a wire nut WIRES Connect in this order e GREEN leads from mounting plate and fan to 3 GREEN GROUND conductor of power source Secure WIRES amp with wire nut a e WHITE wire from fan to white NEUTRAL wire Tee G in ceiling fixture outlet box Secure with wire nut e BLACK wire from fan to black POWER wire in ceiling fi
8. e This fan is designed to be installed on an existing electrical outlet box The outlet box must be UL Listed for ceiling fan installations if it is not a new box must be installed Casablanca extension poles are available for sloped or high ceiling installations e This ceiling fan requires a grounded electrical supply of 120 VAC 60 Hz and a minimum 15 amp circuit The maximum current requirement for the fan with light fixture is 3 8 amps The fan uses about 1 amp or 100 watts Maximum light current is 2 8 amps or 340 watts of lighting e Where wire nuts are employed be sure all bare wires are within the connectors When installing the canopy hatch make sure all wires are within the canopy and that no wires are being pinched For best performance and for your warranty to be valid use only genuine Casablanca blades light fixtures and accessories e The blades in each pack are matched for FUSE BOX equal weight to assure smooth fan operation REMOVE FUSE FOR THE If more than one fan is being installed be CIRCUIT YOU WILL BE careful not to mix blades from different WORKING ON cartons ai e Inspect the contents of your carton for J possible shipping or handling damage and 70 report any such damage directly to your T authorized Casablanca dealer e e Itis always a good idea to have an assistant S 84 to help with the installation
9. e the finish No Need for Lubrication e Never lubricate this fan The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life e Do not attempt to oil the motor Changing Lightbulbs e Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs e Replace bulbs with the same type as you removed from the light fixture e The maximum wattage rating for this fan s light kit is 100 watts For questions or to locate the nearest Casablanca Authorized Service Center call toll free 1 888 227 2178 or visit us on the web at www casablancafanco com 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harm ful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eq
10. m TTD HOLDER M DRYWALL WOOD SCREW SCREW W 72 ANCHOR SCREW 6 32 X 3 3 6 32 X1 CONTROL 12V BATTERY 6 32 2 1 2 2 2 CAUTION Do not use with wall dimmer m STANDARD e TOGGLE ROCKER 1 SWITCH TYPE LIGHT INNER q SWITCH MOUNTING m OUTER HOLES MOUNTING HOLES M switch A COVER ___ SWITCH a PLATE COVER CONTROL CONTROL PLATE BRACKET BRACKET Standard Light Switch Rocker Light Switch Step A Remove the two screws holding the switch cover Step A Break off the two tabs by pushing outward plate Do not remove the cover plate Step B Remove the two screws holding the switch cover Step B Orient the control bracket as shown and line up the plate Do not remove the cover plate two inner mounting holes with those on the switch Step C Orient the control bracket as shown and line up the Step C Install and tighten screws by hand only two inner mounting holes with those on the switch Step D Install and tighten screws by hand only wall Installation Note The wall anchors and 6 32 x 1 screws may be Step A Locate a 2x4 used in situations where mounting to a stud is not pos wall stud in a convenient sible Use the inner mounting holes After securing the location Pree anchor discard the anchor s pointed screws and use the Step B Orient the control 7 yall 6 32 decor ovalhead screws supplied bracket as shown over the fs 2x4 stud ANCHOR Step C Use the 1 wood PANHEAD screws in ei
11. nction and fan speed will resume when power is turned back on REVERSE Auto Resume GS Quick pressing less than 0 7 seconds on off operation of the LIGHT button maintains the desired brightness level set previously HI Note All fans leave the factory set to 00000 You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately VERSA TOUCH 2 CONTROL Step 1 At the circuit breaker or fuse box turn the power off for the BACK fan you want to change Step 2 Open the battery door of the VersaeTouch control and remove the batteries Step 3 Change the dip switch settings assuring that they are different from the previously installed VersaeTouch fan Step 4 Re install the batteries and the battery door on the control Step 5 At the circuit breaker or fuse box turn the power back on for cera aca Pi the fan whose frequency you are changing Step 6 Within 20 seconds of restoring power push the Hi Med and Lo buttons in that order WITHIN 20 SECONDS OF 2 Note You may want to label your controls to TURNING THE FAN ON assure you do not mix them up FRESS IN THIS ORDER TO SET NEW FREQUENCY 1 HI WARNING Do not turn the power off at the circuit breaker 2 MED then back on for the previously installed VersaeTouch 2 3 LO 3 1 fan s as you may inadver
12. otor adapter and the motor Tip The screw showing on the motor should be between the 2 mounting holes for the blade iron Step 11 Align one blade iron hole with the appropriate hole in the motor and the cut out in the the motor adapter Tighten screw by hand only Cowan BLADE ASSEMBLY ON FAN INSTALLATION Step 12 Rotate blade assembly until the other blade iron hole aligns with the cut out and again install and tighten screw by hand only Repeat steps 11 and 12 until all 3 blade assemblies are installed this way 14 20 x 1 4 3mm 6 DOWNROD PRE INSTALLED ALLEN WRENCH MOTOR COVER amp BALL ASSEMBLY FAN PREPARATION IMPORTANT SAFETY INFORMATION BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY MOTOR WIRE Step 14 Route the wires from the motor through the Perma Lock downrod and ball assembly DOWNROD amp BALL Tip The downrod has a tapered thread that is designed AEREO ASSEMBLY to lock completely when correctly installed sea Step 15 Using the provided allen wrench loosen the set screw ALLEN several turns to allow installation of the downrod Thread the SET SCREW downrod into the motor coupling until it stops turning this will take at least four and a half full turns Prepare for fan installation as follows Step 13 Place the motor cover on the downrod as shown MOTOR COVER MOTO
13. our optional Low Ceiling Adaptor LCA available at extra cost can be used to gain 31 2 on certain fan models e Over pool tables be sure to provide plenty of clearance to avoid damage from pool cues or dae e In kitchens be sure to allow for open cupboard doors to clear the fan blades ee H 57 i e Do not install a fan close to or over a pool or spa High humidity combined 4 hey F with corrosive gases will destroy the finish and warp the blades IVING Jo Fan Size Variable fan speed capability permits the use of a full size 52 fan even in smaller rooms For very large rooms two fans may be needed MASTER BEDROOM ae a oy E d G 0 j o FAMILY 0 i fonds ENTRY MAXIMUM Suqgested Extension Pole Lengths HANG TRU Ceiling Height Pole Length EXTENSION ANGLE 32 g Standard POLE 8 6 Standard pe 9 6 Q 6 12 10 12 11 18 12 Pile 13 36 _ o o BLADES MUST BE 4 A MINIMUM OF 7 f ABOVE THE FLOOR When to Use Extension Poles 7 MINIMUM For best performance and best appearance an extension pole should be used with your Casablanca fan when installing on high cathedral ceilings or sloped ceilings Casablanca offers standard poles in increments of 6 up to 5 Custom poles 2 IY ON 4 are available in lengths up to
14. r is defective Replace fan receiver Reverse does not work e The fan receiver is defective Replace fan receiver Fan starts working by itself e There is frequency interference Change frequency as described on Page 13 Fan operates only when transmitter is close e Check that antenna wire is not touching metal plate Fan works but light does not dim e The fan receiver is defective Replace fan receiver Fan works but light does not work The fan receiver is defective Replace fan receiver The light socket is broken Replace socket e A lightbulb is defective Replace lightbulb MARRAKESH Fan Finishes e For cleaning a soft brush or lint free cloth should be used to prevent scratching the finish e A vacuum cleaner brush nozzle can remove heavier dust e Surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft cloth An antistatic agent may be used but never use abrasive cleaning agents as these will damage the finish Blades e Wood finish blades should be cleaned with a furniture polishing cloth Occasionally a light coat of furniture polish may be applied for added protection and beauty e For painted and high gloss blades surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft cloth An antistatic agent may be used but never use abrasive cleaning agents as these will damag
15. tantly change the frequency set tings for it as well If the fan is not functioning after installation 2 Step 1 Check to make sure that batteries are installed correctly E in the control lt E Step 2 Turn the power off to the fan from the circuit breaker 3 C 1 for at least 5 seconds l Step 3 Turn the power back on at the circuit breaker and push aa PRESS IN THIS ORDER TO SET NEW the Hi Med and Low buttons in that order within 20 seconds Step 4 The fan should now function properly OR FUSE BOX 1 HI 2 MED 3 L0 CIRCUIT BREAKER FREQUENCY Geren TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance PROBLEM POSSIBLE REMEDIES Fan will not start e Check the main circuit fuses circuit breakers and wall switch position Check all wire connections Make sure the power is turned off during this inspection e The 9 pin connector is not making good contact Check the 9 pin connector in the receiver mounted in the switch housing The battery is weak Install a fresh battery The fan receiver is defective Replace fan receiver e Check the frequency setting Turn the power off at the circuit breaker only for the fan that is not functioning Check that the jumper switches match in both the receiver and the transmitter Fan wobbles or shakes excessively e Be sure the canopy pin is set properly into the slot on the ball e
16. ther the inner SCREW DRYWALL ANCHOR or outer mounting holes Install and tighten screws 8 by hand only Am o E woop DECOR OVALHEAD SCREW SCREW 1 6 32 X 1 Changes or modifications not expressly This device complies with RSS 210 of Industry Canada Operation is subject to approved in writing by Casablanca Fan Co the following two conditions 1 this device may not cause interference and may void the user s authority to operate 2 this device must accept any interference including interference that may this equipment cause undesired operation of the device VERSA TO UCH2 d Fan Control SEND SIGNAL To start the fan Press the selected speed button to run the fan at the desired speed LED LO Low speed MED Medium speed HI High speed To turn off the fan Press the FAN OFF button Airflow Direction To reverse the airflow press the REVERSE button Reverse operates at any speed whether fan is on or off The fan returns to its set speed after reversing Light Control Turn the light on or off independently from the fan by pressing the LIGHT button Keep pressing the button in excess of 0 7 seconds it becomes a dimmer The light varies from bright to dim over approximately 8 seconds This sequence will reverse the light when it reaches the brightest or dimmest level if you continue to hold the LIGHT button Release FAN the button when the desired level is reached STOP Memory Feature The last light fu
17. tion Before you start go through this Owner s Manual and confirm that you have all the parts CAUTION When removing the shrink wrap be careful not shown in each section to scratch the blades CEILING HARDWARE m CROSSBAR MOUNT ING BRACKET WIRE NUT 4 i ADDITIONAL HARDWARE ny 2 4 x 8 32 ROUNDED HEAD SCREW 2 1 x 8 32 ROUNDED HEAD SCREW 2 FLAT WASHER 2 SUPPORT INSTALLATION PARTS LAG SCREW Qin zat LARGE FLAT WASHER s 1 CANOPY HARDWARE CANOPY CANOPY HATCH Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan an approved ceiling fixture outlet box must be installed and wired Warning To reduce the risk of fire electrical shock or personal injury mount to outlet box marked acceptable for ceiling fan support CANOPY SCREW 8 32 X 41 8 4 S CANOPY LOCK WASHER 8 4 GETTING STARTED CONTINUED Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source either circuit breaker or fuse box lower the old fixture and disconnect the wiring Check the ceiling fixture outlet box to be sure that it is a UL listed ceiling box for ceiling fan applications If it is not a new box must be installed ee Eisen Note After removing the old fixture check the outlet box to insure that it is supported by a joist or beam across i
18. ts upper surface If not a 2 x 4 stud must be installed Step 1 Remove the knockout plug in the center of the out let box or drill a 2 hole for the lag screw to pass through aN Then drill a 4 guide hole into the joist or beam to a depth CEILING FAN S of 3 APPROVED WIRING BOX Step 2 Route the outlet box wires through the keyhole slot of the crossbar mounting bracket as shown Attach the crossbar RIDGE e e e CROSSBAR mounting bracket to outlet box with screws provided assuring MOUNTING SIDE that the outlet box wires are not pinched by the washer DOWN BRACKET CAUTION To reduce the risk of personal injury FLAT use only the mounting hardware provided with WASHER idi the approved outlet box to install the crossbar mounting bracket APPROVED OUTLET BOX HARDWARE WARNING SUPPORT DIRECTLY TO BUILDING STRUCTURE ONLY Step 3 With the large washer attached pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole Tighten until outlet box is firmly mounted to beam This box must be firmly secured to the ceiling We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions LARGE WASHER MarR RAKESH e CANOPY INSTALLATION Step 4 Attach the canopy to the crossbar mounting bracket with three of the 8 32 x 4
19. uipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one s authority to operate this remote control PRODUCT SPECIFICATIONS Model Name Marrakesh Motor 188 x 20mm Direct Drive Model Number 89UXXM Blade Span 64 Dimensions O 25 a ie B 20 Ceiling Line aaa Aa 3 T EET Technology Versa Touch2 W 72 B includes light fixture x a gon PA Optional Light Fixture Exclusive KG89 Light Fixture F 56 E z 1 100 watt halogen lightbulb AO Ibs Airflow 7 900 cfm Electricity Use 84 watts Airflow Efficiency 85 cfm watt Performance data is for fan only No lighting wattage is included
20. xture outlet box Secure with wire nut Inspect each wire nut and ensure that no bare wire is visible pull on each wire to test the connection is mechanically sound ENA Step 21 Tuck the wires into the canopy wire nuts pointed upwards the WHITE and GREEN wires on the opposite side from the BLACK wires Keep all wires clear of the canopy opening Step 22 Install canopy hatch with the last canopy screw and lock washer To do this par tially insert the canopy screw and lock washer before aligning the hatch on the canopy TIP Have an assistant tilt the fan away from the hatch side of the canopy Step 23 If necessary straighten the fan then check to ensure that there is no movement between the canopy and ceiling or ball and downrod CANOPY WASHER CANOPY SCREW NOTE If you have purchased the optional exclusive light fixture for this fan please go to Step 26 If not please continue with Step 24 Step 24 Take the light wires one at a time and tuck them into the pipe opening as shown IMAR RAKESH gt Step 25 Install the finial onto threads and turn clockwise until snug Versa TOUCH2 fe oee Warning To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch W 72 CONTROL m a mmm fu
Download Pdf Manuals
Related Search