Cardo Q2 User's Manual
Contents
1. CARDO SCALA RIDER 02 MultiSet Congratulations and thank you for choosing the SCALA RIDER Q2 MultiSet Bluetooth Headset package for bikers This User Guide will help you operate the headset but you should first familiarize yourself with the Bluetooth functionality of your cel ular phone and or GPS device before using the SCALA RIDER Q2 This retail box contains two SCALA RIDER Q2 headsets that already fac ory paired see details below In wide open terrain two bikers can com Typical effective range is approximately 250 m 800 ft Please note that he actual range can vary widely as a result of many reasons e g terrain obstacles weather conditions etc The SCALA RIDER Q2 is multi talented and in addition to its connec ion to the second Q2 unit it can also serve as a stand alone unit for he following connectivity modes As a Bluetooth headset for mobile phone communication As a Biker to Passenger Intercom device that connects with any SCALA RIDER headset worn by the passenger As a speaker that transmits GPS Navigation instructions from a compatible GPS device As a speaker that transmits audio from the embedded FM Radio As a speaker that transmits music from your MP3 player NOTE Each Q2 headset can establish an audio connection with one Bluetooth device at a time Read the section Using the Headset on how to switch the audio connection between the paired devices Full duplex2. area prior to the gluing process as described in 4 below positioned vertically and not horizontally Be sure to clean the selected CARDO SCALA RIDER 02 MultiSet 4 Use the pre moistened Towelette to clean the helmet area where you want to install the Glue Plate Allow to dry thoroughly 5 Peel the foil cover from the Glue Plates adhesive pad 6 Place the Glue Plate into position according to 3 Press firmly 15 seconds on all 3 parts of the Glue Plate 7 The adhesive pad bonds to full strength over the next 24 hours Therefore it is recommended to not use the headset during this 24 hour period 8 Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed Attach the speakers to the Velcro inside your helmet opposite your ears short speaker cord for the left ear A and the long speaker cord B for the right ear You may want to use the supplied Velcro pad SpeakerA Speaker B Using two speakers inside the helmet may be prohibited in certain jurisdictions If this is the case you should tuck away the long corded speaker underneath the helmet padding as follows Lead the speaker B alongside the rim of the padding to the right side and then back to the left side near speaker A Then place the speaker B underneath the padding Speaker B ATTACHING Slide the headset downwards along the sliding panel until a clicking sound indicates
3. CE Notice The SCALA RIDER Q2 headset the Product is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Articles 3 18 3 1 and 3 2 The Product is manufactured in accordance with Annex II of the above directive Declaration of Conformity DOC The SCALA RIDER Q2 headset is compliant with and adopts the Bluetooth Specification 2 0 and has successfully passed all interoperability tests that are specified in the Bluetooth specification However interoperability between the device and other Bluetooth enabled products is not guaranteed WAIVER AND GENERAL RELEASE By using the SCALA RIDER Q2 headset s hereafter referred to in the singu lar you will waive substantial legal rights including the right to sue Please read the following carefully before using the device If you do not accept all terms of this agreement you should immediately return the product for a full refund By using the headset you agree to be bound to this agreement and forfeit the right to sue Using a communication device while riding a motorcycle scooter moped ATV quad bike or any other vehicle or equipment whether on land water or air jointly referred to as Vehicle requires your complete and undivided attention Cardo Sys tems Inc including its Officers Directors Affiliates Parent Company Representa tives Agents Contractors Sponsors Employees Suppli
4. calls allow you to speak and hear the other party speak simultaneously Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Redial and Call Reject features The Q2 supports headset and handsfree profiles at up to 10 m 30 ft distance from the mobile phone Requires Bluetooth compatibility on the part of the GPS device municate via intercom in full duplex at a range of up to 500 m 1 640 ft SCALA RIDER 02 MultiSet o KOVANE SDIO lt Volume Up m Charging Jack B Volume Down CTRL Control Button Power On Power Off Answer End MC Multi Connection Radio On Off change stations Initiate Terminate Buddy Intercom call with Primary or Secondary Buddy Left Speaker short cord Two Helmet Clamps Right Speaker long cord Microphone Sliding Plate NOTE The use of MP3 Jack two speakers may be illegal in certain jurisdictions Please check the local regulations and act accordingly CARZDO SCALA RIDER 02 MultiSet 2 Wall Chargers Be 2 Allen Wrenches T 2 sets of Velcro Pads 2 MP3 Cables 2 Glue Plates i 2 Pre moistened Towelettes 2 Carry Pouches aa lt 4 Microphone Sponges Flat sponge for full face helmets and round sponge for other helmet types User Guide including Warranty and Registration form IMPORTANT Your headsets are wa
5. protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device IC RF Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter European
6. that the headset is locked in place REMOVING Press here to remove Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand We recommend that you remove the headset from the helmet when not in use SCALA RIDER Q2 MultiSet CARDO GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT REQUIRED ACTION Turn on the Press the CTRL Button steadily for at least three headset seconds Turn off the Press the CTRL Button steadily for at least three headset seconds Increase the Short press the Volume Up Button volume Decrease the Short press the Volume Down Button volume AGC Automatic Gain Control In addition to manual Volume Control the SCALA RIDER Q2 will automatically increase and reduce its volume according to ambient noise and driving speed AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the SCALA RIDER Q2 are prioritized as follows Highest 1 Mobile phone Audio GPS device Incoming outgoing calls GPS audio and navigation instructions 2 Primary Buddy Audio and Secondary Buddy Audio 3 FM Radio Lowest 4 MP3 Connectivity A high priority Audio Source will always interrupt any lower priority Audio Source Mobile phone call interrupts Intercom call Intercom call interrupts FM Radio Making Intercom calls To start a Buddy Intercom call with the P
7. Intercom calls If you are not speaking with any one once the other party tries to initiate a Buddy Intercom call the call will begin immediately TROUBLESHOOTING THE INTERCOM First make sure your microphone is located properly in front of the center of your mouth The SCALA RIDER Q2 is designed for use in loud environments Please make sure to test the Intercom functionality ina LOUD environment such as next to an idling motorcycle Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections Setting Voice Connect Intercom preference Primary vs Secondary Buddy The headset s Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone You can define which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom NOTE The Primary Buddy has priority by default To toggle the Voice Connect Intercom between Primary and Secondary Buddy Press and hold the Volume Up Button for three seconds and you will hear a beep One beep Voice Connect set to Primary Buddy Two beeps Voice Connect set to Secondary Buddy Enable Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep The default status is Voice Connect enabled NOTE The Enable Disable Voice Connect feature affects both the Intercom and the mobile phone functionalit
8. MED IN THE ENCLOSED MANUAL Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE WHETHER BASED ON BREACH OF CONTRACT TORT INCLUDING NEGLIGENCE PRODUCT LIABILITY OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY RETURN FOR FULL REFUND IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDI TIONS YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOW ING THE PURCHASE OF THE DEVICE proof of purchase required AND SUB JECT TO THE WRAPPING BEING INTACT WHEN DOING SO PLEASE REFER TO THIS SECTION BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE www cardosystems com n T
9. ac padding and the external shell of the Plate helmet 3 Adjust the Clamp s location so that the microphone is located opposite the center of your mouth and then tighten the screws You may need to reposition the Clamp repeatedly until you identify the best spot The microphone must be positioned CORRECT INCORRECT vertically and not horizontally Glue Plate Method You have the option to glue the Helmet Clamp onto your helmet when the above standard method cannot be used or in case you prefer to secure the Helmet Clamp with adhesive glue This option has been successfully used for a range of high end helmets NOTE While we have no reason to believe that the gluing op tion might negatively affect any helmet Cardo does not assume any responsibility to that affect irrespective of its nature and circumstances The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims Caution This process can be done only once 1 Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp s back plate 2 Determine the location on the helmet where the Helmet Clamp must be attached 3 Adjust the Helmet Clamp s location on he Helmet so that the microphone is located opposite the center of your mouth You may need to reposition he Clamp repeatedly until you identify CORRECT INCORRECT he best spot The microphone must be
10. alcohol that may affect your alert ness or any mind altering substance and will not carry use or consume these substances before or during the use of the Device You fully acknowledge our warnings and understand that a risks and dangers exist in using the Device while in traffic including but not limited to injury or illness strains fractures partial and or total paralysis death or other ailments that could cause serious disability b these risks and dangers may be caused by the neg ligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device c these risks and dangers may arise from foresee able or unforeseeable causes You hereby assume all risks and dangers and all responsibility for any losses and or damages whether caused in whole or in part by the negligence or other conduct of others including the Company 5 You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund see refund option below Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FORA PARTICULAR PURPOSE AND NON INFRINGEMENT THE DEVICE AND ITS ACCESSORIES ARE PROVIDED AS IS AND AS AVAILABLE WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSU
11. connection In addition each unit can be paired with an addi tional SCALA RIDER headset for Intercom communication Please note that you can speak via Intercom to one Buddy headset at a time NOTE This Manual refers to the Intercom users and other parties as Primary Buddy and Secondary Buddy SCALA RIDER Q2 MultiSet CARDO N PRIMARY BUDDY PAIRING requires two SCALA RIDER Q2 headsets If either headset is turned OFF turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times Make sure that both headsets are now flashing slowly in Blue 3 Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly indicating it is in Intercom Pairing mode 4 Repeat Step 3 again for the second SCALA RIDER Q2 headset Both headsets should now be flashing rapidly in Red 5 Within a few seconds both headsets will show a solid Red light for two seconds and then begin flashing slowly in Blue SECONDARY BUDDY PAIRING requires three SCALA RIDER Q2 headsets In addition to the Primary Buddy pairing between the two units in your retail box you can pair your headset with the Secondary Buddy headset by repeating the above pairing procedure NOTE Your headset can communicate with either the Primary Buddy or the Secondary Buddy However neither the Primary Buddy nor the Secondary Buddy can communicat
12. device 2 With the SCALA RIDER Q2 headset turned ON press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating SCALA RIDER Q2 MultiSet CARDO 3 Search for Bluetooth headsets on your GPS device by following the device s instructions Please consult your GPS device s User Manual for more information 4 If your GPS device prompts for a PIN or Passkey enter 0000 four zeros 5 Your GPS device will confirm that pairing has succeeded The headset will begin flashing slowly in Blue 6 If you wish to use a Bluetooth mobile phone to make and receive calls through the headset you must now pair your mobile phone to your GPS device by following your GPS and or mobile phone s instructions NOTE If the Pairing process is not completed within two minutes the headset will return to Standby mode The Helmet Clamp must be attached to the left side of the helmet Once attached the headset unit can be mounted or released from the Helmet Clamp at any time There are two methods that can be used in order to attach the Clamp onto the helmet Standard Method Recommended for most helmet types Glue Plate Method Recommended for helmets to which the standard method cannot be applied using the Glue Plate included in the box Standard Method 1 Use the enclosed Allen Wrench to loosen Allen the two screws on the Back Plate Wrench 2 Slide the Back Plate between the internal B
13. e SCALA RIDER Q2 headset turned ON press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating 3 Search for Bluetooth devices on your phone by following the phone s instructions Please consult your phone s User Manual for more information 4 After a few seconds the phone will list the SCALA RIDER Q2 as a discovered device Select it and follow your phone s instructions to accept the pairing 5 When prompted enter 0000 four zeros as your PIN or passkey 6 Your phone will confirm that pairing has succeeded and the headset will begin flashing slowly in Blue NOTE If the Pairing process is not completed within two minutes the headset will return to Standby made With some mobile phones you may need to tap the CTRL button to connect the headset to the phone after pairing is complete The SCALA RIDER Q2 headset will automatically connect to the last phone connected to the headset SET UP FOR BLUETOOTH GPS DEVICE PAIRING If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset s speakers you must first pair your headset to the GPS device NOTE Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the SCALA RIDER 2 Please consult your GPS device s User Manual for more information TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH GPS DEVICE 1 Turn on your GPS
14. e a station is found searching stops and you can hear the station To save this station refer to the following section To continue searching press the Volume Up or Volume Down Button again for three seconds You may still continue to listen to the current unsaved station Pressing the MC Button in this case will switch to the next saved Station Saving an FM Radio Station The FM Radio is equipped with a memory capacity of six stations EEE j SEE C AR DO SCALA RIDER 02 MultiSet e Select the station you wish to replace by tapping the MC button until you find the station you want to replace Search for a new station as described above Tap the MC Button within 20 seconds of finding the station to save the current station If you don t save the station the Radio will exit search mode without saving the current station You can still continue to listen to the current unsaved station Tapping the MC Button in this case will move to the next saved station Your SCALA RIDER headset can be connected to an MP3 player audio device by simply plugging it to the Helmet Clamp s jack with the audio cable as follows 1 Power on the headset to have it on Standby mode flashing slowly in Blue 2 Connect one side of the audio cable to your MP3 player audio device s jack and the other side to the helmet Clamp s jack as shown in the photo 3 Operate the MP3 Player audio device by Connect t
15. e among each other directly via Intercom NOTE If the Pairing process is not completed within one minute the headset will return to Standby mode STEP 2 Optional SET UP FOR RIDER TO PASSENGER INTERCOM PAIRING There are two ways that the SCALA RIDER Q2 can be used for Rider to Passenger communication A Both Rider and Passenger are using SCALA RIDER Q2 headsets like the two units in your retail package To Pair the two headsets follow the Steps listed in the section above titled PRIMARY BUDDY PAIRING B The Rider is using a SCALA RIDER Q2 and the Passenger is using a SCALA RIDER headset i e a SCALA RIDER Solo a SCALA RIDER FM or a SCALA RIDER TeamSet Driver unit headset To Pair the two headsets 1 Starting with the SCALA RIDER headset turned OFF press and hold the CTRL button until the Red Blue lights begin rapidly alternating 2 Starting with the SCALA RIDER Q2 turned ON simultaneously press and hold the CTRL Button and MC Button for six seconds until the Red light begins flashing rapidly indicating it is in Intercom Pairing mode 3 Within a few seconds the SCALA RIDER Q2 will show a solid Red light for two seconds and then begin flashing slowly in Blue NOTE If the Pairing process is not completed within one minute the headset will return to Standby mode NOTE When using a SCALA RIDER headset as a Passenger headset Voice Connect Intercom can be initiated only by the SCALA RIDER Q2 headset Manual Con
16. e equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help SCALA RIDER Q2 MultiSet CARDO Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Industry Canada IC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the IC rules These limits are designed to provide reasonable
17. erating it rest solely and entirely with the user of this Device irrespective of whether the Device is used by the original purchaser or any third party Cardo hereby notifies you that using this Device may also be in contravention to local federal state or national laws or regulations and that any use of the Device is entirely at your sole risk and responsibility You your heirs legal representatives successors or assigns hereby voluntarily and forever release discharge indemnify and hold harmless Cardo from any and all litigation claims debts demands actions and liability which may arise directly or indirectly from using the Device for any distress pain suffering discomfort loss injury death damages to or in respect to any person or property however caused WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law N You fully understand and assume the risks in using the Device including risk of negligent acts or omissions by others You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner You confirm that you are at least eighteen 18 years of age and that you have been advised of the risks associated with the use of the Device You further confirm that you will not consume any
18. ers and Resellers jointly referred to as the Company or Cardo strongly advises you to take all necessary precautions and remain alert to the traffic weather and road conditions if you choose to use the SCALA RIDER Q2 headset including all derivative models irrespective of its commercial name or branding the Device and stop your Vehicle on the roadside prior to initiating or receiving calls Any publications advertisements an nouncements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic By way of purchasing this Device and not returning it for a full refund see below you are irrevocably releasing indemnifying from any liability loss claim and ex SF TEEN CARDO SCALA RIDER 02 MultiSet pense including attorneys fees and holding Cardo harmless for any bodily injuries harm or death as well as losses or damages in goods to any Vehicles including your own or to any property or asset that belong to you or to third parties any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction Cardo will not be responsible for any physical damages irrespective of reasons conditions or circumstances including malfunctioning of the Device and all risks associated with op
19. he audio cable to using its buttons FF REW PLAY PAUSE the helmet Clamp s jack NOTE Volume can only be adjusted through the MP3 Player Any other audio connection Phone call FM Radio Intercom call will automatically mute the MP3 Player The audio signal will return only when headset is once again in Standby mode For additional information please visit our website at www cardosystems com FAQ www cardosystems com faq or contact us at support cardosystems com Phone USA and Canada 1 800 488 0363 International 4989 450 36819 Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning th
20. nect Intercom can be initi ated from either headset by pressing the MC button for SCALA RIDER Q2 and CTRL button for other SCALA RIDER headsets RESET INTERCOM PAIRING You can delete all of the headset s Intercom pairings at any time oe CARDO SCALA RIDER 02 MultiSet 1 Place the SCALA RIDER Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above 2 Once the Red Light begins flashing rapidly press and hold Volume up for three seconds 3 The Red and Blue Lights will flash five times confirming that the Reset Pairing was successful SET UP FOR MOBILE PHONE CALLS PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the SCALA RIDER Q2 you must first pair your headset to the mobile phone NOTE If you have a compatible Bluetooth GPS device you wish to use with the SCALA RIDER 2 please skip this step and continue ahead to STEP 4 SET UP FOR BLUETOOTH GPS DEVICE Pairing is a one time process Once the headset is paired to a specific mobile phone during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range If the connection between the phone and headset is lost tap the CTRL button to reconnect the devices TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH MOBILE PHONE 1 Turn on your phone and make sure its Bluetooth function is activated 2 With th
21. rimary Buddy while the headset is on Standby you can either VOICE CONNECT er MC BUTTON CONNECT Single tap the MC Button A Buddy Intercom call will be established To end the Buddy Intercom call single tap the MC Button again Start talking A Buddy Intercom call will be established and stay on until both sides are quiet for 30 seconds To start a Buddy Intercom call with the Secondary Buddy while the headset is on Standby MC BUTTON CONNECT MC Button Double tap the MC Button A Buddy Intercom call will be established To end the Buddy Intercom call double tap the MC Button again NOTE When using a SCALA RIDER Headset not a Q2 version as a Passenger headset Voice Connect Intercom can be initiated only by the SCALA RIDER Q2 headset Manual Connect Intercom can be initiated rom either headset Failed Connection On the SCALA RIDER Q2 if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone GPS ntercom call you will hear a double beep indicating the Buddy is busy Reconnecting the Intercom If the SCALA RIDER Q2 and its ntercom Buddy headset go out of range and disconnect from each other the SCALA RIDER Q2 will automatically try to reconnect to its ntercom Buddy for five minutes CARDO SCALA RIDER 02 MultiSet You can manually reconnect at any time by pressing the MC Button single tap for Primary Buddy and double tap for Secondary Buddy Receiving
22. ter resistant designed for use under moderate rain or snow conditions However the headsets are not waterproof and should not be used under severe weather conditions The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device NOTE WHILE MOST INSTRUCTIONS IN THIS MANUAL REFER TO THE HEADSET IN THE SINGULAR THEY APPLY TO BOTH UNITS UNLESS INDICATED OTHERWISE Make sure that the headset is fully charged for at least five hours before initial use 1 Connect the wall charger to the headset s Charging Jack located between the two Volume Buttons 2 While charging the Red Light turns on it may take up to 15 seconds until the Red Light turns on When charging is complete the Red Light will turn off Rider to Pa zA Passenger Embedded SA gt Full Duplex FM Radio Intercom i Connection Bike to Bike Intercom up to 500 meters A 1 640 ft SCALA RIDER Q2 or SCALA RIDER E Family Headset TS a Mobile Phone GPS SET UP FOR BIKE TO BIKE INTERCOM PAIRING Pairing is a one time process that is required for mutual recognition be tween a headset and other B uetooth devices Once the two headsets are paired they will remain paired and automatically recognize each other whenever they are within range The two headsets in your retail box are already factory paired and relate to each other as the Primary Buddy
23. w to enjoy the functions of the FM Radio The SCALA RIDER Q2 enables you to listen to FM Radio while you are not receiving audio from another audio source While listening to the radio you do not have to worry about missing any calls as the headset automatically mutes the FM Radio and switches to Bluetooth headset operation when an incoming call is received or when you decide to initiate a call When the conversation is over the headset automatically tunes back in to the FM Radio Turning the FM Radio On While no call is on the headset either mobile phone call or Intercom call press and hold the MC Button on your headset for three seconds to turn on the radio The radio tunes in to the last radio station you were listening to With some phones you should wait a few seconds after ending a call before turning on the Radio Turning the FM Radio Off While the radio is turned on press and hold the MC button for three seconds to turn the Radio off Switching Preset FM Radio Station There are six pre set Radio stations available on your SCALA RIDER Q2 While the Radio is on tap the MC Button to cycle between saved stations Searching for a New FM Radio Station While the Radio is on press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset Pressing Volume Up will search upwards higher frequency Pressing Volume Down will search downwards lower frequency Onc
24. y PHONE FUNCTIONS Answer a call Short press the CTRL Button or speak loudly any word of your choice Reject a call Short press the MC Button or remain silent or 15 seconds Terminate a call Short press the CTRL Button During Standby short press the CTRL Button and state the name of the person you wish o call This feature is supported only by mobile phones that support the Voice Dial eature Redial Press and hold the Volume Down Button for hree seconds Voice Dial NOTE If your Bluetooth mobile phone is paired to a Bluetooth GPS device not directly to the SCALA RIDER Q2 some of the above Phone functions may not be compatible When the headset is on an active phone call any Buddy Intercom call request will be rejected automatically Once the phone call audio link drops you can initiate and accept Buddy Intercom calls n 1 SCALA RIDER Q2 MultiSet CARDO None Headset is off Alternating Red blue flashes Mobile phone GP S Pairing mode Rapid Red flashes Intercom Pairing mode 1 blue flash every 3 seconds Standby No call is in progress 2 blue flashes every 3 seconds Call being initiated or in progress FM Radio ON 1 red flash every 3 seconds Battery is low 2 red flashes every 3 seconds Call being initiated or in progress FM Radio ON and battery is low Solid red Headset is being charged Your headset is equipped with a high quality FM Radio receiver This section explains ho
Download Pdf Manuals
Related Search