Canon Satellite TV System DT 9500 CI User's Manual
Contents
1. GB 49 15 Troubleshooting 5 Remote control does not operate To manipulate the equipment with the remote control its emitting part should directly point towards its receiving part of the product Check the battery of the remote control 6 Reservation is unavailable Check if it is not overlapped with other reservation Check if the power is off 7 Watching scrambled channel is not available Make sure the correct Smartcard is plugged in Make sure the Smartcard is correctly inserted and insert the Smartcard again Check if the Smartcard is damaged Make sure you have subscribed to the channel GB 50 16 Specification MPEG Transport Stream A V Decoding Power Supply Aspect Ratio 4 3 16 9 Input Voltage AC 90 250V 50 60Hz Video Resolution 720 x 576 720 x 480 Audio Mode Single Dual mono Stereo Joint stereo Memory Type Switching Mode Power Supply SMPS Power Consumption Operation mode Max 30 W Standby mode Max 30 W Protection Separate internal fuse amp Lightning A V amp Data In Out TV SCART Video Output CVBS RGB S Video Audio Output VCR SCART Video Output CVBS S Video Video Input CVBS RGB S Video Audio Output S PDIF Digital Audio Output Fiber Optic Resolution 20 bits Flash Memory 2 Mbytes protection Graphics MPEG amp 16 Mbytes a A2. The software update via satellite will only occur under the following circumstances 1 The equipment should have appropriate loader software Caution Please note that if normal loader software is not equipped the product may not be updated or operate properly after software update The manufacturer decides to release the software via a designated satellite The equipment must be tuned properly to the same antenna equivalent to that of the manufacturer 4 Update software when the signal strength and quality is high If the weather is not favorable and the signal strength and quality are not recommendable perform the software update later oN Caution e Please be careful to keep the power on and the power cord plugged in during software update If the power is off during software update fatal damage may be caused to the product e Please be careful not to pull out the signal line LNB cable during software update Update may be interrupted and the product may not operate Note e Other functions will not activate while software update takes place It may take 5 10 minutes to update software Scheduling operation cannot work during software update GB 47 14 Software Upgrade Updating software is largely divided into two ways automatic and manual search in MENU System Settings System Information Software Upgrade Select Automatic Search to search pre defined DIGITURK TPs for new software automatically When new software is a
3. Advanced lnStallatiON biie weld oe bed A A A AA A Ea GB24 O EAS AAA AN GB29 BALCONES a An oe he e GB32 6 System Settings toma coca oge broa uee E Daa aE ES a aade GB33 6 1 Language Seting re aoaaa aaa ada a a a a lb nada da GB33 6 2 Time and Date Seting eri ener aE a e GB33 6 S ANOUTDUT Setting i EE A GB34 CAUAR TUNNI rra to a DE E dla a a ia A date nas trees ADA a laa LA A iA bod a GB34 6 5 Other Settings ma A A o GB35 6 6 SystemiINfOrmation ia o A A A A A E AS EP ME vie GB36 GB 3 Contents GB 4 T Parental Control A aa e a ee Ace GB37 TA Parental Rating ise eserivan OA AA AE AT oh aa GB37 7 2 Modify PIN Code sacacasa GB37 1 3 Front PanerLOck ti rai as te tl ia ata id at dd ata Fad de Bh GB37 8 ChamMelLiStoii A eset A A AAA eit dees GB38 8 1 Switching ChannelS io es tes FG GG toa ey bt E GEC GE tt doce le alge GS OE tato GB38 8 2 Setting Property of Chanmel ooooocccccococccccno entree nett enn e tenn aee GB39 8 3Favouite Listra yr sd eros Ea E AE E bs AE A ERSTA ane Re acer GB40 A a ed beta dig eee ed cheney weed i ee eds deka GB41 10Programme Guide daria Seta ieee yeh tee bg a aa yada ts neeek a E th Cie aN GB42 WA Mail ces es ead ae A a eee sine nee Dees ed ere ae pee dine eae Pe ee eee GB44 12 Conditional Accessi sso eh A ar ah pint aes A ret MR A EL GB45 13 Commoni interface 3 6 osc A eee ee eee Re ee ee ee ne GB46 14 Software Uparade A tee cas atk aca cea A A di GB47 14 ALOTA OVEr INE Al sos a ESE A
4. Control GB 10 AV Selects the input source between TV and the product MODE Switches between DIGITURK and OTHER modes NUMERIC BUTTONS Enter a TV radio channel number GUIDE EPG Displays the programme guide i INFORMATION WHITE Displays the information about the channel and programme ARROW BUTTONS Changes channels or moves the cursor up down left or right in menu option TIME RED Displays the current time on the screen FAV Favourite channel GREEN Displays Favourite channel list 9 CH CH Changes the channel 10 PP Recall Returns to the previous channel in each mode 11 FREEZE Freezes the scene you are watching Does not cease audio 12 WIDE Changes the display format 13 STANDBY Switches between operation and standby modes 14 OPTS Displays the main menu 15 BACK Returns to the menu option 16 OK Selects a menu or confirms the selection Displays the channel list while watching a programme 17 LANGUAGE SOUNDTRACK BLUE Displays the a soundtrack list where available 18 TXT SUBTITLE YELLOW Displays the subtitle language list where available 19 V V Adjusts the audio volume 20 MUTE Mutes or unmutes the audio temporarily 21 Z00M Enlarges the picture 22 TV RADIO Switches between TV and radio Does not work in DIGITURK mode COLOUR BUTTONS R G B Y W Select color keys for interactive applications G
5. E kak dont ante Retake og ehhh hes Gary GB47 15 TroubleShooting ii ieee ceed eee dee doe eee a a ete ee a oe Lee dee eee ened ee dette need ee cease GB49 16 Specifications issia sinh cer A a ancl tae GB51 1 Before Using the Product This chapter provides detailed instructions on the product and its accessories 1 1 Package Contents When you unpack your package contents make sure you have all the necessary items shown in the figure below If any of the items are missing or damaged please contact your local product distributor for replacement Remote Control Batteries User s Manual Warranty Card SCART Cable RCA Cable RF Cable Note The product image may differ from the actual product GB 5 1 Before Using the Product 1 2 Front Panel 96 8 06 0 1 STANDBY Button 5 DIGITURK CH LED Switches between operation and standby modes Amber light is emitted when viewing DIGITURK channel 2 MODE Button 6 STANDBY LED Switches between DIGITURK and OTHER modes Red light is emitted when the product is in standby mode 3 CH CH Button 7 SMARTCARD SLOT Moves the TV radio channel up down Slot for a Smartcard 4 MAIL LED 8 Cl MODULE SLOT Green light is emitted when the mail was received Slot for a Cl module Note Refer to 1 4 Conditional Access when you insert the Smartcard GB 6 1 3 Rear Panel 6 6 BBO 0D 1 LNB IN 7 AUDIO L R Connects to a satellite antenna cable Connects to the TV or VCR and outputs
6. Resets all saved positions of the motor relative to the 0 position Installer Mode Only DiSEqC Command Mode Select Installer or User mode The following table shows the value of the motor setting options Satellite Setting Satellite Name ARABSAT 203A 4 Movement Stop 0 Motor Control Search DISEQC Command Mode User strength Quality Motor Limit Setting DiSEqC Command Mode Movement Motor Control Installer East Stop West Search Go to Store Reset User Stop 60E Stop 0 Stop 60W Search Go to Store GB 26 To initialise the satellite position saved at Motor Antenna set DISEqC Command Mode to Installer set Motor Control to Reset then press the OK button You will see a warning message To continue the procedure press the OK button To set the motor position for each satellite manually select the Satellite Name set DISEqC Command Mode to Installer and then set Movement to one option among East Stop or West The motor starts moving The level of signal strength and quality bar at the bottom of the screen will indicate the best position of the dish Set Motor Control to Store when you find the best position then press the OK button to save the position To move the motor to the pre set position of the satellite select the desired Satellite Name set DISEqC Command Mode to User set Motor Control to Goto and set Movement to the desired value Movement is
7. antennas or LNBs select DiSEqC input to connect to antenna or LNB Motorised System When using motorised system select Enabled Otherwise select Disabled When Motorised System is set to Enabled DiSEqC Input is disabled LNB Voltage You can select Standard voltage or High voltage LNB Power You can select On or Off When you complete the settings press the OK button to move to the Manual Search menu GB 24 2 Manual Search You can search channels of the selected satellite by transponders using the transponder information Antenna Alternative Select antenna alternative which has different combinations of settings for search Antenna Alternative 16 is predefined for SMATV e Frequency Enter transponder frequency e Polarisation Select the type of polarisation Symbol Rate Select or enter transponder symbol rate e FEC Select FEC Forward Error Correction e Network Search If you want to search channels for multiple transponders select Yes Otherwise select No e Automatic Skip When skipping all scrambled channel search select Yes Otherwise select No Advanced In advanced mode enter Video Packet ID PID Audio PID and PCR PID Manual Search Antenna Alternative 1 ARABSAT 243A2D Frequency 4000 Polarisation Horizontal Symbol Rate 28125 FEC 3 4 Network Search Yes Automatic Skip No Advanced juv ength Quality 4
8. button and press the OK button To view the teletext page use the CH CH 4 w PP or NUMERIC buttons GB 20 4 Menu Map DIGITURK Advanced Installation Installation Organise Channels Factory Settings Language Setting Time and Date Setting A V Output Setting UHF Setting Other Setting System Settings System Information Parental Rating Parental Control Modify PIN Code Front Panel Lock Channel List a N Conditional Access Common Interface Simple Advanced Calendar Biorhythm Games Internal Slot External Slot GB 21 4 Menu Map Menu structure varies according to the item and its operation You can easily navigate the menu using the following instructions 1 NO 7 R LV Press the OPTS button to display the main menu screen Select the item you want using the a w button Press the OK button to move from a menu to a sub menu Press the 4 button to select option values Press the NUMERIC buttons to enter the option values Press the BACK button to return to the parent menu Press the OPTS button to exit the menu screen Note Some menu items are access controlled When accessing to the protected menu you will be prompted to enter the PIN code Enter the PIN code using the NUMERIC buttons The default PIN code is set to 0000 GB 22 5 Installation 5 1 DIGITURK 1 DIGITURK Installation You can automatically search the channel without entering any othe
9. displayed Select the required country using the a w button and press the OK button If you select Turkey the DIGITURK Installation menu will be displayed And if you select other countries the Advanced Installation menu will be displayed Note For detailed information about searching channels refer to 5 1 1 DIGITURK Installation and 5 2 Advanced Installation an O ED undugunuz Uikey veginiz y i GB 17 3 Basic Operation 3 2 Viewing Programme You can change the channel using the CH CH a w or NUMERIC buttons You can also use the Channel List or Programme Guide You can adjust the audio volume using the V V or 4 p button Banner Programme Information The banner is always displayed for a specific period of time whenever you switch channels You can view the programme information by pressing the i button while watching a programme You can see the detailed information about the current programme by pressing the i button twice If the detailed information is more than one page use the a w button to move to the previous or next page Press the BACK button to hide the banner You can adjust the display time of banner in MENU System Settings Other Setting Banner Duration Channel number and name Programme name and theme Current day date and time Friday 25 12 2006 15 45 Broadcasting time 3 Next programme info CUE ee Remaining time DIGITURK Logo Represents parental level Indicates the m
10. the keyboard Select a character using the a w 4 button and press the OK button to enter the selected character After entering the new name press the YELLOW button to save it To delete a character press the BLUE button e To switch to the standard keyboard press the RED button To switch to the extended keyboard press the GREEN button Note You must enter the PIN code using the NUMERIC buttons to view the locked channels The default PIN code is set to 0000 You are not allowed to organize DIGITURK channels except of lock feature GB 29 5 Installation 2 Organise Favourite A B You can add channels to Favourite groups using Organise Favourite TV Radio Channels MENU Installation Organise Channels Organise TV Radio Channels Organise Favourite A B Before leaving Organise Favourite TV Radio Channels screen you will be prompted to save the changes If you would like to save the changes select OK and press the OK button The Organise Favourite TV Radio Channels screen consists of Favourite Group and Favourite List on the left side of the screen and Channel List on Organise Favourite Radio Channols the right side You can move the highlighter in order of Favourite Group i X f Channels Favourite List and Channel List using the button You can move the rset highlighter in reverse direction using the d button es So To add channels to Favourite List select a channel in Channel List using the RPI Asia 4 v
11. used to fine tune the position of the motor Press the OK button The motor will move to the position of the selected satellite 4 Motor Limit Setting To enter this menu press the RED button in Satellite Setting menu You can set the maximum for both East and West to prevent damage to the antenna Limit Setting When Limit setting is set to Enabled the motor does not move exceeding the limit When Limit setting is set to Disabled the Motor Limit Setting setting is released Limit Setting Disabled 4 gt Movement Stop Movement You can select one among East Stop or West Store East Limit Store East Limit You can save the East Limit J Store West Limi Store West Limit You can save the West Limit GB 27 5 Installation 5 Automatic Search If you select the satellite to search channels according to Antenna Setting you can automatically search the channel without entering any other information To enter Automatic Search menu press the OPTS button then select Installation Advanced Installation Automatic Search Antenna Alternative Select antenna alternative which has different combinations of settings for search The Satellite Name is automatically Automatic Search displayed Antenna Alternative 16 is predefined for SMATV Antenna Alternativo e Automatic Skip When skipping all scrambled channel search select ARES ones No Yes Otherwise select No Search Type Auto Network Searc
12. After setting the parameters of search press the OK button to start channel search Wait until the operation is completed After finishing search operation the result window will be displayed You can delete the channels using the a w 4 and the RED button To cancel deleting operation press the RED button again The screen also shows the number of the channels found and the transponder information To save the found channels press the OK button Note If the antenna is properly set up the signal strength bar and quality bar level located at the bottom of the screen moves up e Press the BACK button to stop search GB 25 5 Installation 3 Satellite Setting This menu appears only when you enable Motorised System in Antenna Setting menu and press the OK button while Antenna Alternative in Manual Search menu is selected e Satellite Name Select a satellite to identify a motor antenna If the desired satellite name is not listed then select other Movement In user mode this is used to fine tune the position of the motor In installer mode this is used to search for the position of the satellite manually Motor Control You can select one option among Search Go to Store or Reset Search Searches for channels on the selected transponder Go to Moves the motor to the saved position of the selected satellite Store Saves the current position of the motor for the selected satellite Reset
13. B 11 2 Setup This chapter describes how to set up the product Select the most appropriate procedure depending on your requirements Before you connect the product to any other equipment you must disconnect all equipments from their power sources Note If you encounter any problem when setting up the product please contact your local product distributor 2 1 Connecting Antenna TV VCR 1 Using SCART Cable 1 Connect the antenna to the LNB IN of the product 2 The SCART cable is connected as in the figure above GB 12 2 Using RCA Cable 1 Connect the antenna to the LNB IN of the product 2 The RCA cable is connected as in the figure above GB 13 2 Setup 3 Using RF Cable AF cable 1 Connect the antenna to the LNB IN of the product 2 The RF cable is connected as in the figure above Note The default UHF channel is 36 GB 14 2 2 Connecting Audio System 1 Connect the optical S PDIF terminal and Dolby Digital decoder to listen to higher quality sound 2 Connect VIDEO on the product and VIDEO IN on the TV using the RCA cable 3 Connect AUDIO L R on the product and AUDIO IN L R on the audio system using the RCA cable GB 15 2 Setup 2 3 Powering On 1 Connect the power cord of the product to a wall outlet GB 16 3 Basic Operation 3 1 Installation Wizard When powering on your product for the first time after purchase the selecting country screen is automatically
14. HUMAX EASY DIGITAL www humaxdigital com Digital Satellite Receiver CryptoWorks Embedded DT 9500 Cl User s Manual The product image may differ from the actual product Notice Thank you for purchasing a HUMAX product Please read this user manual carefully to be able to safely install use and maintain the product at maximum performance Keep this user manual next to your product for future reference Throughout the whole manual Note indicates additional product operation information to make the user aware of possible problems and information of any importance to help the user understand use and maintain the installation Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories All other trademarks are the properties of their respective owners Copyright O 2006 HUMAX Corporation Not to be copied used or translated in part or whole without HUMAX s prior consent in writing except approval of ownership of copyright and copyright law The information in this document is subject to change without notice GB 1 Safety Warning The product has been manufactured to satisfy international safety standards Please read the following safety precautions and warnings carefully Disconnect the product from the mains before you start any maintenance or installation procedures Do not overload a wall outlet extension cord or adapter as this may result in electric fir
15. PIN code is set to 0000 7 3 Front Panel Lock You can lock the front panel When setting Lock all buttons on the front panel except the STANDBY button do not work GB 37 8 Channel List There are five types of channel lists All Favourite Network Satellite Alphabet to find channels you are interested in quickly and easily All channel lists display all searched TV or radio channels sorted by channel number Favourite channel list displays favourite channels with three predefined sub groups and two user defined sub groups Network channel list displays channels with several network subgroups Satellite channel list displays channels classified by satellites Alphabet channel list displays all searched TV or radio channels sorted by channel name 8 1 Switching Channels 1 Press the OK button while watching a programme to display the channel list You can also display the channel list using the MENU Channel List Simple or Advanced JETIK 2 Press the COLOUR button to display the corresponding channel list RED E y Te cual EY All channel list GREEN Favourite channel list YELLOW Network 4 le channel list BLUE Satellite channel list WHITE Alphabet channel list a a 3 Select a channel using the a w CH CH or NUMERIC buttons and S202 SALONZ press the OK button to change to the selected channel Ta Note Press the MODE button to switch between DIGITURK and OTHER channel list Except in DIGITURK ch
16. System Memory Physical Specification EEPROM 8 Kbytes Size 310 mm X 60 mm X 237 mm RF Modulator Weight Net 1 8 kg Operating 0 Cto 45 C TV standard PAL 1 G B D K Storage Humidity 5 95 RH Non condensing Preset Channel CH 36 GB 51
17. annel list whenever you press the TV RADIO button while the channel list is displayed the channel list will be switched between TV and radio channel list There are four user defined sub groups A D in DIGITURK Favourite channel list GB 38 8 2 Setting Property of Channel You can add the current channel to Favourite group In addition you can lock unlock skip or delete the current channel while watching a programme The operation is as follows 1 Press the OK button while watching a programme The channel list will 4 MA appear on the screen You can also display the channel list using the All MENU Channel List Simple or Advanced You can select the type of Li boi a the channel lists All Favourite Network Satellite Alphabet by pressing KANALD m 84 vH the COLOUR button y 2 2 Press the OPTS button while the channel list is displayed SAILING CHANNEL 3 Select an option Favourites Lock or Unlock Skip Delete using the a v Pia button and press the OK or 4 p button sizot bem EOE r 4 After setting property of a channel press the OK or BACK button to save SILO V SF the changes 2 AN Note There are two sub groups in the TV and radio Favourite channel list When unlocking a channel you will be prompted to enter the PIN code The default PIN code is set to 0000 When switching to a locked channel you must enter the PIN code to view the channel You will not be able to watch skipped cha
18. audio signals 2 LNB OUT 8 RF OUT Connects to another digital Set Top Box Connects the RF output jack of the product and the RF 3 RS 232C input jack on the TV with the RF cable Connects to your PC to update software The detailer channelis se 4 TV SCART Sees Connects a TV SCART cal A O aaa 5 VCR SCART 10 S PDIF o TEADE Outputs digital audio signals S PDIF 6 VIDEO Connects to the TV or VCR and outputs video signals GB 7 1 Before Using the Product 1 4 Conditional Access Although some TV and radio channels are free to air most TV and radio music channels are available on a subscription basis and can only be enjoyed via Conditional Access component 1 Inserting Smartcard A Smartcard looks similar to a credit card and entitles you to view and listen to all the channels you choose to subscribe to The Smartcard slot on the product can be used for CryptoWorks Smartcard only 1 Open the right hand flap on the front panel of the product 2 Hold the Smartcard horizontally with the electronic chip small squared shape gold in colour facing upwards 3 Insert the Smartcard into the top slot Smartcard GB 8 2 Inserting Cl Common Interface Module Your product is equipped with a slot for Common Interface Cl Open the right hand flap on the front panel of the product Insert the Smartcard into the Cl module and the Cl module into the slot 1 2 GB 9 1 Before Using the Product 1 5 Remote
19. button and press the OK button For more information about how to edit the channels in Favourite List refer to 5 3 1 Organise All Channels GB 30 3 Organise Satellites You can delete satellites and transponders To enter Organise Satellites menu go to MENU Installation Organise Organise Satellites Channels Organise Satellites i iad ENANA The Organise Satellites screen consists of Satellite List on the left side of the om screen and Transponder List and Channel List on the right side You can move the highlighter in order of Satellite List Transponder List and Channel List using the button You can move the highlighter in reverse direction using the 4 button You can select a satellite in Satellite List or transponder in Transponder List using the a w button Press the RED button to delete the selected satellite or transponder GB 31 5 Installation 5 4 Factory Settings You can restore the product to the factory settings using the Factory Settings menu MENU Installation Factory Settings You will be prompted to enter the PIN code The default PIN code is 0000 For more information refer to 5 1 1 DIGITURK Installation Warning Please note that once you perform the factory setting all data except the customised PIN code will be restored to the factory settings GB 32 Installation DIGITURK Advanced Installation C Organise Channels Factory Setting Factory settings willbe restorad A
20. e openings in the unit where they can touch dangerous voltage points or damage parts When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part Unauthorised substitution may result in additional damage to the unit GB 2 Contents 1 Before Using the Production a a eer ee A a oe een ew Wee sb de eee Mee dee ee sires GB5 1 1 Package Contents cece nen nent een dette enn e tet E E GB5 T2 Front A RN AN GB6 TtSR ar Panahna p ii a a A Ai GB7 1 4 Conditional Access ci A Sebo od bad Wedd pe bea bags Gente edhar weep es GB8 1 5 Remote Control wi aro o a io a btt aE GB10 LS A A A ane Md nee A A tee phe eee GB12 2 1 Connecting Antenna TV VCR 2 cece ect nent nett nannaa GB12 2 2 Connecting Audio System 0 0 cece ete nent een ete nee aee GB15 DI POWER On a8 da GB16 3 Basic Operation ad GB17 3 1 Installation Wizard ccoo tienes Pelee PERLE Tee ale Peete A A Tee eT Ce sale teh la A glee GB17 3 2 VIEWING Progra MME six cisco ee AEE AESLAR APR Ada EA ADE oe breif bop Raped dae Abe GB18 DAB SUD UII SS esc Sack Sheltie O RO RO eC GB19 SA Soundtrack song ve Mb ioe eae ed hes Miears sere ebee eb ee aie are ee bie eeee EAE DE envy nine GB19 ATEO ica ci ra bated nd diese A a road date Rood GB20 4 Men Map niaaa A A A A a as GB21 5 IMSTAlAION a A A A A E AAA A ET RT ry dE GB23 5 1 DIGITURK a le do GB23 5 2
21. e or shock The product should not be exposed to liquid of any kind In addition no objects filled with liquid such as vases should be placed on the apparatus Do not stand the product on soft furnishings or carpets Do not stack electronic equipments on top of the product Do not use any unsupported attachments as these may be hazardous or cause damage to the product Disconnect the product from the mains before connecting or disconnecting the cable from the antenna or TV The LNB cable must be earthed to the system earth for the satellite dish Place the product indoors to avoid exposing it to lightening rain or sun Do not place it near a radiator or heat register Make sure it has more than 10 cm clearance from any appliances susceptible to electromagnetic influences such as a TV or a VCR Do not block these openings with any object and do not place the product on a bed sofa rug or other similar surface If you place the product on a rack or bookcase ensure that there is adequate ventilation and that you have followed the manufacturer s instructions for mounting Do not place the product on an unstable cart stand tripod bracket or table where it can fall A falling product can cause serious injury to a child or adult and serious damage to the appliance Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left unattended and unused for long periods of time Do not insert anything through th
22. een Display OSD set the duration of the banner when switching channels select automatic or manual mode for changing to reserved channel and set the duration of the reminder Other Setting Duration Changing to Reserved Channel Reminder Duration Opaque 4 gt 10 Manual 60 GB 35 6 System Settings 6 6 System Information The System Information menu MENU System Settings System Information provides information such as STB status signal level of channel Systom Information and software upgrade STB Status Signal Detection Note Software Upgrade e You can also display STB Status by pressing i and OK button For more information about software upgrade refer to 14 Software Upgrade GB 36 7 Parental Control The Parental Control menu MENU Parental Control lets you control the access to programmes by programme rating Parent Control Note Enter the PIN code using the NUMERIC buttons The default PIN Parental Rating code is set to 0000 Attain code T Front Panel Lock Unlock 7 1 Parental Rating Set Parental Rating by age level no block allows you to watch programmes without any blocking You can block all programmes regardless of age level The blocked programmes require the PIN code 7 2 Modify PIN code We recommend you to change the old PIN code to a new one periodically to ensure If you have forgotten your PIN code please contact your local product distributor The default
23. ess the OK or BACK button to return to the previous menu 2 Biorhythm You can adjust your birth year and date to see your current biorhythm status Press the 4 p button to move to the next step Press the a w button to change a value in the step Press the BACK button to return to the previous menu You can select games using the 4 p button Use the a w 4 OK COLOUR or BACK button according to the instructions displayed on the screen GB 41 10 Programme Guide The programme guide provides the programme information for all channels based on date and time In addition it provides convenient ways to view BA DIGITURK Guide Now done Dl programmes in Now Next Weekly or Quick mode to search your desired programme and to watch or reserve it 20 You can go to the programme guide screen by just pressing the GUIDE button or by using MENU EPG To close the guide screen press the GUIDE or BACK button SALONA CONSTANTINE TURKCELL VIP TV You can navigate the guide using the following instructions Press the RED button to display the current or next programme list no RANTASTIK OBRILIM 2006 DOGAUSTO Press the GREEN button to display the programme list for a week DOON OLAN CROAT rc A e Press the YELLOW button to display the reserved programme list e Press the BLUE button to display the simple Guide This is also called Quick Guide Next Weokly Reserved Quiok GB 42 Press the WHITE b
24. h Yes e Search Type If you want to search channels through all field of tuner 950 2150MHz2 select Manual Otherwise select Auto to search channels with the preset parameters In detail mode you can add the desired Symbol Rate 2600 3000 4540 6000 11000 27500 6000 e Network Search If you want to search channels for multiple transponders select Yes Otherwise select No When you complete the setting press the OK button to start channel search Note Channels found during Advanced Installation menu shall be stored to the OTHER mode To switch between DIGITURK and OTHER channels press the MODE button on remote control GB 28 5 3 Organise Channels 1 Organise All Channels You can edit TV or radio channels using Organise TV Radio Channels MENU Installation Organise Channels Organise TV Radio Organise Radio Channels pr Channels Organise All Channels Channels oo RDP Antena 1 You will be prompted to enter the PIN code The default PIN code is 0000 a Before leaving Organise TV Radio Channels screen you will be prompted to save the changes If you would like to save the changes select OK and press the OK button You can delete move lock or unlock skip and rename channels You can select a channel and press the COLOUR button to execute the corresponding operation as described on the screen When you rename a channel the keyboard will appear on the screen You can change the name using
25. inimum level of ages that the programme is targeted at Displayed only the programme is reserved Displayed only when the channel is a locked channel TOR The channel group the programme is included in Moves to the channels within the group when the channel is switched GB 18 m o E DO Digital Displayed only when the channel is a scrambled channel Displayed only when subtitle information is available Displayed only when there is any teletext information Displayed only when the programme is braodcast in Dolby Digital 3 3 Subtitle If the current programme provides subtitle information the subtitle icon will appear on the banner You can select the language for the subtitle using the TXT SUBTITLE button You can select a default subtitle language in MENU System Settings Language Setting Subtitle Language 3 4 Soundtrack If the current programme is available in multiple audio languages you can A select the language that you wish to listen in using the LANGUAGE Soundtrack SOUNDTRACK button You can select the default audio language in MENU System Settings Language Setting Audio Language GB 19 3 Basic Operation 3 5 Teletext When the channel supports teletext the teletext icon E is displayed on the banner To enter Teletext mode use the TXT SUBTITLE button to display teletext To display teletext menu press the OPTS button in teletext mode Select your desired teletext function using the 4
26. l appear on the screen Sometimes a new message will be AA directly displayed on the screen while you are watching a programme The old E 24 02 09 38 37 Jail ENG mails will be deleted automatically when your mail box overflows Select a mail Eee pad peg 24 02 09 38 54 3all ENG using the a w button then press the OK button to read the mail The message will be displayed If you would like to delete the read mail select Delete and press the OK button GB 44 12 Conditional Access You can check the information of Internal or External Smartcard using the MENU Conditional Access Conditional Access Internal Slot Extemal Slot GB 45 13 Common Interface You can check the information of Cl module using the MENU Common Interface irdeto MAIN GB 46 14 Software Upgrade In order to maintain proper performance of the product it is essential to have the most up to date software 14 1 OTA Over the Air OTA an abbreviation of Over the Air is a standard for the transmission of software through a broadcast system OTA is simply an alternative method for downloading software versions However the manufacturers reserve the right for deciding the release of the software for their products by beaming the latest software versions over the air via satellite Note that OTA is only limited to certain geographical regions mainly due to different antennas having different footprints area where the signal can be received
27. nnels by using the CH CH button However you can watch the skipped channels using the NUMERIC buttons or Channel List e For detailed information about how to register all channels as Favourite Channel refer to 5 3 2 Organise Favourite A B and 8 3 Favourite List Skip and Delete are not available for DIGITURK channels GB 39 8 Channel List 8 3 Favourite List You can check and edit Favourite list quickly and easily 1 2 O Favourite A E 3 DIOITURK KANAL D X JETIX JETIX PLAY Press the FAV button to display Favourite list while watching a programme Press the RED button to display the all channel list Select the channel you want to add to Favourite list and press the OK button Press the BLUE button to view the channel you select To close the all channel list press the BACK button Press the GREEN button while displaying Favourite list to switch between Favourite A and B Press the YELLOW button to move the channel to the location you want Note Press the MODE button to switch between DIGITURK and OTHER channel list There are four user defined sub groups A D in DIGITURK Favourite channel list GB 40 9 Utility The product provides various utilities calendar biorhythm and games To use utilities go to MENU UTILITY p Maln Menu 1 Calendar You can see the monthly calendar Press the a w button to change the year Press the 4 button to change the month Pr
28. r information 2 Change CAS Slot of All DIGITURK Channels You can check the CAS slot currently in use and change the CAS slot of all DIGITURK channels Select the CAS slot you want using the a w button and press the OK button DIGITURK DIGITURK Installation Notice External SmartCard is currently in use External SmartCar Common MITA Seloot GB 23 5 Installation 5 2 Advanced Installation You can search other channels except DIGITURK channel Enter the PIN code using the NUMERIC buttons The default PIN code is set to 0000 1 Antenna Setting You can set antenna and LNB information to search channels using Antenna Setting IMENU Installation Advanced Installation Antenna Setting Antenna Alternative Select antenna alternative which has different combinations of settings for search Antenna Alternative 16 is predefined Antenna Setting for SMATV Antenna o 1 e Satellite Name Displays the satellite list in name order If the desired SABA Name A satellite name is not listed then select User Defined You can enter the ce in e Satellite Name using the keyboard displayed on the screen i DiSEqC Input DiSEqC B LNB Frequency Select the L O Local Oscillator Frequency of the LNB A ea ei e 22KHz Tone When using the 22HKz tone switch select Enabled LNB Power on Otherwise select Disabled e DiSEqC Input If you are using DiSEqC Digital Satellite Equipment Control switch to connect multiple
29. re you sure No EZ 6 System Settings The System Settings menu MENU System Settings lets you customise your product according to your perference 6 1 Language Setting You can set the default language for menu audio and subtitle 6 2 Time and Date Setting You can set the current time and turn the product on or off automatically Once you set the Wakeup time and Sleep time the product is turned on and Time and Date Setting off everyday Auto Time Country Warning When setting Wakeup Channel No press the MODE button to change the channel mode oe Wakeup Time Disabled Wakeup Channel No Tv1 Sleop Time Disabled GB 33 6 System Settings 6 3 A V Output Setting This menu lets you adjust the audio and video output set Dolby Digital match the screen ratio to your TV select the display format according to the screen AIV Output Setting ratio select the TV standard and set the NTSC mode TV Output Type cves Note You can choose the Dolby Digital audio stream whenever possible a A Genco by selecting ON in the Dolby Digital setting L Dolby Digital ON i TV Screen Format 4 3 Display Format Centre TV Standard Auto NTSC Mode 3 58 6 4 UHF Tuning You can select UHF Channels for your TV and adjust fine tuning setting The channel range and frequency change according to PAL Standard The default UHF channel is 36 GB 34 6 5 Other Setting You can adjust the transparency level of On Scr
30. utton to reserve the selected programme in Now Next Weekly or Quick mode MD nico auian nnus Press the WHITE button to change the reservation mode or to cancel the bailar reservation in Reserved mode CONSTANTINE Select a channel using the a w or CH CH button When switching mal idad ds channels using the a w button press the OK button to display the selected CONSTANTINE channel on the right side of the screen Loany A Select a day in Weekly mode using the 4 p button and press the OK button 09 FANTASTIK GERILIM 2005 DOGAUSTO OUOLERI OLAN DEDEKTIF JOHN CONST Noxt Waokly Reserved Note Press the TV RADIO button to switch to Radio Guide The reservation icons on the reserved programmes in the guide differ according to the reservation type ia Once Reserve the programme once v Daily Reserve the programme everyday aj Weekly Reserve the programme once a week If the programme is overlapped with another programme adjust the reservation appropriately If the channel is locked restricted by watching time you will be prompted to enter your PIN code to complete the reservation Press the MODE button to switch between DIGITURK and TV Guide Press i button in the selected programme to view the detail information And you can also make a reservation in the detail information screen GB 43 11 Mail You receive mails sent by broadcasting company When a new mail arrives the i l Fiki envelope icon wil
31. vailable to download the product will be automatically powered off and on If new software is not found by automatic update use manual update For more information about how to set the manual search refer to 5 2 2 Manual Search GB 48 15 Troubleshooting Before contacting your local service please read the following instructions If the product does not work normally after completing the following troubleshooting please contact your local product distributor or service centre 1 The LED on the front panel does not light Check the main power cable and make sure that it is plugged into a suitable power outlet No picture Make sure that the product is in operation mode Make sure that the AV Cable is firmly connected to the TV Make sure that the antenna line is correctly connected to the equipment Check the brightness level of TV Check if the channel is on air Poor picture or sound quality Make sure there is no mobile phone or microwave oven near the equipment Check the signal strength and quality which can be influenced by weather Change satellite dish into a bigger one if it is small Replace the LNB with a one with low noise factor if the noise factor is high Replace the LNB with a new one if it is damaged or out of order No or poor sound Check the volume level of the TV and product Check the mute status of the TV and product Press the SOUNDTRACK button to change the audio type
Download Pdf Manuals
Related Search