Canon C7010VPS/C6010VPS/C6010S Owner's Manual
Contents
1. These sections contain important information with regard to the user safety and the prevention of equipment problems Make sure that you observe the safety rules hereinafter This helps to assure safe operation of the product Make sure that you observe all the precautions mentioned below Note Depending on the context the terms system machine and equipment all will be used to designate the product for which user documentation is applicable Note Some parts of the contents of this section may not be applicable to your product Note Please refer to the corresponding Material Safety Data Sheets for specific safety informa tion You can download the Material Safety Data Sheets from the support site of your product Please refer to the back cover for more information Warning and Caution Symbols 6 Warning Ignoring this warning could cause serious injury or even death Caution Ignoring this warning could cause injury or damage to property Note Indicates additional important information The indicators above are used on the warning labels or in the manuals to categorize the level of safety warnings Chapter 1 Instructions for safe use Instructions for safe use Disassemble and modification Warning Do not remove covers and panels which are fixed to the machine Some machines have a high voltage component or a laser beam source inside that could cause electrical shock or blindness Do not modify this machi2. and the wavelength is 658 nm Mercury All Countries At the end of the equipment s service life the mercury containing fluorescent lamp must be removed from the equipment and treated separately according Directive 2002 96 EC Waste Electrical and Electronic Equipment Dispose of in accordance with all federal state and local regulations The European Waste Catalogue EWC number of the mer cury containing fluorescent lamp is 20 01 12 Battery Labeling EU Only This product contains a battery Please do not remove the battery If the battery needs replacement this should be done only by authorized service technicians who are aware of the removal instructions This product contains a button cell s It They is are located in a printed circuit board s that is are essential for the continuous error free functioning of the product The button cell s should be removed only by authorized service technicians who are aware of the removal instructions Button cell specification pacity stances if applicable Caution Canon Oc does not accept any liability for any damage or consequences if Button cell location Button cell ca Contains the following sub the batteries are removed by persons other than Canon Oc authorized service techni clans Chapter 2 Regulation notices 13 Regulation notices End of Life WEEE EU only x The symbol the crossed out wheeled bin indicates that at end of lif
3. machine for the ventilation duct Actions in response to troubles 8 Warning When a piece of metal water or any other similar foreign matter gets inside the ma chine immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative Immediately stop using the machine if the machine becomes excessively hot emits smoke or produces unusual odors or noises Immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative Caution Stop using the machine if the machine was dropped or a cover was damaged Imme diately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative Chapter 1 Instructions for safe use Instructions for safe use m LCD display Do not rub press or touch the display surface with hard material because the polarizer at the surface can be easily scratched The LCD module consists of glass Therefore the LCD module can damage when you drop pinch strongly or punch the module If glass breaks be careful that you do not get injured by the glass fragments Contact your authorized service representative Moving the machine Caution m Make sure that you disconnect the power cord and other cables before you move the machine m Make sure that you check the documentation for the space requirements before
4. 10 C 50 F to 40 C 104 F m Relative Humidity RH 20 to 90 18 Chapter 3 General information Beyond the Ordinary Printing for Professionals canon CANON INC 30 2 Shimomaruko 3 chome Ohta ku Tokyo 146 8501 Japan CANON U S A INC One Canon Plaza Lake Success NY 11042 U S A CANON CANADA INC 6390 Dixie Road Mississauga Ontario L5T 1P7 Canada CANON EUROPA N V Bovenkerkerweg 59 61 1185 XB Amstelveen The Netherlands oe See http www canon europe com for details on your regional dealer Creating global leadership in printing CANON LATIN AMERICA INC Canon and Oc have joined forces to create the global 703 Waterford Way Suite 400 Miami Florida 33126 U S A a ie gt leader in the printing industry For our customers this CANON AUSTRALIA PTY LTD 1 Thomas Holt Drive North Ryde Sydney N S W 2113 Australia CANON CHINA CO LTD 15F Jinbao Building No 89 Jinbao Street Dongcheng District Beijing 100005 China to the new Canon Oc combination for CANON SINGAPORE PTE LTD e Enterprise printing in the office and corporate 1 HarbourFront Avenue 04 01 Keppel Bay Tower Singapore 098632 CANON HONGKONG CO LTD 19 F The Metropolis Tower 10 Metropolis Drive Hunghom Kowloon Hong Kong e Large format printing of technical documentation signage and display graphics combines Canon and Oc technology with the support of the Oc direct sales and service organizations Look pri
5. Oc PRISMAsync CANON GROUP User manual Safety information Copyright 2011 Oc All rights reserved No part of this work may be reproduced copied adapted or transmitted in any form or by any means without written permission from Oc Oc makes no representation or warranties with respect to the contents hereof and specifi cally disclaims any implied warranties of merchantability or fitness for any particular purpose Further Oc reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes Edition 2011 05 Contents Contents Chapter 1 Instructions for safe USe anno anno nn nnnnnnnnnnnn nun nun nn nn nn nn nn nn nn nn nn nn nn ann nn nn 5 Instructions for safe USC ccccccececececscececececececucucucuauauaeauavacaeseaeeeenseeseauaeaeaes 6 Chapter 2 Regulation noticeS 11 REgUlAL ON NOOO Sissi 12 Chapter 3 General information uuu u0000ononnnnn anno nn nn nn nn nn nn nn nun nun nun nun nn nn nn nn nn nn ann nn 17 Caution labels and notationS nun nn nn nn nn nn nnnnnnnn 18 Contents Chapter 1 Instructions for safe use Instructions for safe use Instructions for safe use Introduction All products have been tested in accordance with the strictest international safety standards Please read the following sections before you connect the machine to the power supply
6. e of the equipment separate collection is required in the EU Member States The black bar specifies that the appliance is put on the market after August 13 2005 Reference Directive 2002 96 EC Contact your local organization for further information RoHS China only The Environmental Protection Use Period EPUP applicable for the printing system designated for deliveries to the Peoples Republic of China is 20 years This EPUP which does not include consumables or expendables does not affect any warranty that is provided for the system and may not be construed or interpreted as a separate guarantee for the printing system Energy consumption All countries 14 In order to limit energy consumption during times of non use the PRISMAsync has a Sleep mode during which the power level is reduced Power Modes and Delay Times Energy consumption and efficiency are influenced both by the product technology and by the settings chosen by the user especially the delay times that are selected to enter re duced power states The following delay times have been pre set Power Modes and Delay Times Operational mode Default delay time minutes Low power 20 minutes The modes above are automatically entered after the Default Delay Time has elapsed counting from the moment the last print has been produced These settings are recom mended and for most users ensure both ease of use and low energy consumption The minimum and maximum
7. ne because this could cause a fire electrical shock or breakdown Ifthe machine contains a laser the laser beam source could cause blindness Caution Do not place any liquids on the machine To avoid any risk only properly qualified and authorized service technicians are allowed to modify the machine Do not bridge any mechanical or electrical circuit breakers Power cord Warning Do not scratch wrap heat twist bend place a heavy object on or cause any other damage to the power cord The use of a damaged power cord exposed core wire broken wire for example could result in a fire or breakdown If you find any of these conditions immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative Only use the mains connector cable that was supplied with the machine Power source Warning m Put the power plug directly into a wall socket that has the same configuration as the plug The use of an adapter leads can result in an inadequate power supply If a proper wall outlet is not available ask a qualified electrician to carry out the installation Do not connect the machine to a mains voltage that differs from the value as stated on the power marking label Do not use a multiple outlet adapter or an extension lead Contact your authorized service representative if an extension lead is required Note m If connection to a different mains voltage is req
8. norme NMB 003 du Canada Laser Safety All Countries 12 Laser safety This is a digital machine which operates using a laser There is no possibility of danger from the laser provided the machine is operated according to the instructions in this manual Since the radiation emitted by the laser is completely confined within a protective housing the laser beam cannot escape from the machine during any phase of user opera tion This machine is certified as a Class laser product This means the machine does not produce hazardous laser radiation CDRH regulations This machine is certified as a Class Laser product under Radiation Performance Standard according to the Food Drug and Cosmetic Act of 1990 Compliance is mandatory for laser products marketed in the United States and is reported to the Centre for Devices and Radiological Health CDRH of the U S Food and Drug Administration of the U S Department of Health and Human Services DHHS This means that the device does not produce hazardous laser radiation The label shown on page xx indicates compliance Chapter 2 Regulation notices Regulation notices with the CDRH regulations and must be attached to laser products marketed in the United States Caution Use of controls adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure This is a semiconductor laser The maximum power of the laser diode is 21 mW
9. ntroom 2011 Oc Illustrations and specifications do P 3 e Production printing for marketing service bureaus and not necessarily apply to products and services offered in each local raphic arts market Technical specifications are subject to change without prior grap notice Trademarks mentioned in this document are the property of e Business Services for document process outsourcing their respective owners 2011 05 CUS
10. uired contact your authorized service representative Power plug Warning m For machines that are connected via a wall socket Place the machine close to a wall socket that is easily accessible The power plug is intended to serve as a disconnect device Chapter 1 Instructions for safe use 7 Instructions for safe use Grounding Warning m Connect the power cord to an electrical outlet wall socket that is equipped with a grounding terminal m This equipment was not designed for connection to an IT power system An IT power system is a voltage network in which the neutral wire is not grounded Installation Warning m Make sure that the machine is placed on a level horizontal surface of sufficient strength m Do not place this machine on an unstable or tilted bench m Do not place this machine in a location that is subject to lots of vibrations and shocks m Do not use flammable sprays liquids or gases near this product because this could cause a fire Note It is recommended that you connect only copy control products or other products which meet the inter national product safety and radio frequency interference stan dards Only use an attachment cable as specified by the manufacturer Ventilation Caution Do not block the machine s ventilation openings Do not place the machine in rooms which are too small and insufficiently ventilated Be sure to allow a clearance of 60 mm or more at the back of this
11. values are between the brackets The Delay Times can be changed Shorter delay times will lower the energy consumption even further but may cause longer recovery times In some cases longer delay times may prove to be more convenient but it should be noted that this may cause an increase in energy consumption Therefore from an energy preservation point of view longer delay times are not recom mended Chapter 2 Regulation notices Regulation notices Automatic duplex Using both sides of paper reduces paper costs national energy consumption and the amount of paper in the waste disposal process Therefore thePRISMAsync is default set for automatic duplex copying and printing Chapter 2 Regulation notices 15 Regulation notices 16 Chapter 2 Regulation notices Chapter 3 General information Caution labels and notations Caution labels and notations Introduction You can find the power marking label at the bottom side of the controller If connection to a different mains voltage is required contact your authorized service representative Do not remove caution labels or caution notations If a label or notation is soiled please clean the label or notation If you cannot make label or notation legible or if the label or notation is damaged please contact your service representative Operating environment The environmental requirements for correct operation of the machine are as follows m Operating temperature T
12. you move the machine Vacation Caution m Unplug the machine when you will not use the machine for a long period of time Chapter 1 Instructions for safe use 9 Instructions for safe use 10 Chapter 1 Instructions for safe use Chapter 2 Regulation notices Regulation notices Regulation notices Introduction This section describes the regulation notices Radio Interference suppression all countries except USA Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures FCC approval USA only This system has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the system is operated in acommercial en vironment This system generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense ICES 003 Interference causing equipment Canada only This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la
Download Pdf Manuals
Related Search