Briggs & Stratton 1695354 User's Manual
Contents
1. 11 Install Upper Tube to Cover 12 Install Middle Tube 12 Normal Removal amp Installation 14 INStAN ATOM 2 e xs eo tracer tod ea cte et he rie Eon 14 Removal omes tone trece Tenia Suan eic nb el dune 15 A GENERAL WARNINGS Know the unit s controls and how to stop quickly READ THE OPERATOR S MANUALS Read and obey all safety decals Only allow responsible adults who are familiar with the instructions to operate the unit Disengage the PTO Shut off the engine and wait for all moving parts to stop before attaching adjusting or disconnecting any part of the collection system Check the collection system to make sure it is bolted tightly to the unit DO NOT operate the unit without either the entire grass catcher or the deflector in place Turn off the PTO to disengage the blades when not mowing DO NOT mow in reverse unless absolutely necessary Always look down and behind before and while travelling in reverse DO NOT turn sharply when travelling alongside a building or any object Slow down before turning DO NOT carry passengers When collection system is removed from the mower deck the deflector must be properly installed Collector bags are subject to deterioration and wear during normal use Inspect the bag SAFETY DECALS This unit has been designed and manufactured to2. CONQUEST 1700 2700 YT amp PRESTIGE 1800 2800 GT SERIES Install Spacers 1 Install the rear spacers C Figure 3 Secure with two 1 2 13 x 2 1 2 capscrews E washers D spacers C and 1 2 13 nylock nuts A per side Figure 1 Install Side Brackets A Nut 3 8 16 B Lockwasher 3 8 C Side Bracket D Capscrew 3 8 16 x 1 Figure 2 Install Rear Spacers A Nylock Nuts 1 2 13 B Capscrew 1 2 13 x 2 1 2 C Spacers D Washers 1 2 Figure 3 Install Rear Spacers Nylock Nuts 1 2 13 Capscrews 1 2 13 x 2 1 2 Spacers Washers 1 2 ooo Remove Blowout Baffle Install Baffles 1 Remove and discard short blowout baffle C Figure 1 Determine which baffle to use See Figure 5 4 carriage bolts B and locknuts D from mower Chart deck A 2 Lift side discharge chute H Figure 6 3 Insert baffle F through discharge opening and position baffle into place 4 Tighten carriage bolts A and nuts E on baffle F 5 Tighten carriage bolt B and nut E on baffle F 6 Position baffle G into place 7 Tighten carriage bolts C and nuts E on baffle G 8 Tighten carriage bolts D and nuts E on baffle G 44 Mower Deck 50 Mower Deck Figure 4 Baffle Removal A Mower Deck A RH side 26 1 4 long RH side 29 3 4 long B Carriage Bolts 5 16 18 x 3 4 C Blowout Baffle Short D Nuts Whiz
3. Support A Hitch and Upright Support Assembly B Frame spacers 10 INSTALL COLLECTOR BAGS INSTALL LOWER DISCHARGE CHUTE 1 Raise the cover A Figure 13 1 Lift discharge deflector up D Figure 14 2 Attach collector bags B using grass bag hanger 2 Insert lower chute rod A into mounting plate B C to bag hanger post D 3 Pull rubber strap C and secure by placing hole closest to knob in strap completely over locknut N RE Figure 13 Install Collector Bags A Cover B Collector Bag C Grass Bag Hanger D Bag Hanger Posts oO Figure 14 Install Lower A Lower Chute Rod B Mounting Plate C Rubber Strap D Discharge Deflector E Locknut ischarge Chute 11 Figure 15 Install Upper Tube to Cover A Upper Tube B Cover C Ridge Upper Tube D Ridge Cutout INSTALLING UPPER amp MIDDLE TUBES 1 Slide the upper tube E Figure 15 into cover B aligning ridge C with cutout D as shown 2 See Figure 16 for correct hole location and secure the upper tube E to middle tube using screw F 2 Slide middle tube D Figure 16 into upper tube E 3 Slide middle tube D over boot A Pull strap B and place hole completely over pin C 12 44 Frame Hung Mowers 50 Frame Hung Mowers 44 Free Floating Mowers 50 Free Floating Mowers Figure 16 Install Middle Tube Lower Chute Strap Rubber Pin Middle Tu
4. be properly installed in the down position and retained by the spring latch 1 Unhook strap P Figure 17 from pin O Slide middle tube H into upper tube G and remove middle tube H Remove upper tube G from cover B 2 Lift up cover B remove and empty bags E 3 Unhook strap I from locknut and capscrew K Remove lower chute N from mounting plate L See that the discharge deflector J returns to the DOWN position 4 Remove hair pin D and pins C then remove cover B Und E 3 JJ 3 lt Note To prevent loss of parts reinstall pins C and hair pins D in support assembly hinge pivots E Figure 17 5 Remove hitch support assembly A from rear frame spacers S 15 Simplicity MANUFACTURING INC 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www SimplicityMfg com e MASSEY FERGUSON LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www MasseyLawn com Briggs amp Stratton Yard Power Products Group Copyright O 2007 Briggs amp Stratton Corporation Milwaukee WI USA All Rights Reserved SMAPPER PRODUCTS 535 Macon Street McDonough GA 30253 www Snapper com AGCO LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 AGCOLawn com
5. lt gt Simplicity Jv MASSEY FERGUSON AGCO SWAPPER OPERATOR S MANUAL Turboless Triple Catcher Turboless Triple Catcher Mfg No Description 1695354 44 amp 50 Turboless Triple Catcher LL CAUTION Read and follow all instructions Manual Part No 1734740 Revision 01 Rev Date 05 2007 TP 100 4527 01 AT SMAN SAVE THESE INSTRUCTIONS READ THE MANUAL The operator s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation Safe operating techniques an explanation of the product s features and controls and maintenance information is included to help you get the most out of your equipment investment Failure to obey the safety rules could result in loss of control of the unit sever personal injury or death to you or bystanders or damage to property or equipment Safety Icons The alert symbol is used to identify safety information about hazards that can result in personal injury A signal word DANGER WARNING or CAUTION is used with the alert symbol to indicate the likelyhood and the potential severity of the injury In addition a hazard icon may be used to represent the type of hazard An explanation of hazard levels and icons are as follows DANGER This indicates a hazard which if not avoided will result in serial injury or death A WARNING This indicates a hazard which if not avoided
6. other attachments Never operate on slopes greater than 17 6 10 After Operation Remove any debris from the the screen on the underside of the lid The blower housing and tube should be removed for cleaning Inspect the grass bags for wear or damage Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover Storing The Grass Catcher Clean the grass catcher thoroughly using a mild detergent other products may damage the tube Remove any debris from the screen on the underside of the lid If paint has been scratched on metal parts touch up with paint or apply a thin film of oil to prevent corrosion Store in a dry area Dry thoroughly before storing for a long period of time Always store away from moisture A CAUTION Do not leave grass in bagger containers Empty containers after each use and before storing Failure to do so may result in spontaneous combustion which could develop into a fire Assembly INSTALL MOUNTING PLATES BROADMOOR 1600 2600 LT SERIES Install Plates amp Spacers 1 Mount the side brackets C Figure 1 to both sides of the frame using the holes shown Secure with one 3 8 16 x 1 capscrew D 3 8 lockwasher B and 3 8 16 nut A per side 2 Install the rear spacers C Figure 2 Secure with two 1 2 13 x 2 1 2 capscrews E washers D spacers C and 1 2 13 nylock nuts A per side INSTALL MOUNTING SPACERS
7. the bags may be full discontinue mowing stop the unit disengage the PTO shut off the engine and then empty the catcher or clear the tube A WARNING ALWAYS shut off the tractor Disengage the PTO and allow all moving parts to stop BEFORE disconnecting or clearing tube or emptying catcher Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine rider and mower free of grass leaves and excess grease Do not stop or park rider over dry leaves grass or combustible materials Before Operation Clear the lawn of all sticks stones wire and other debris which may be caught or thrown by the mower blades Check grass condition If wet wait until later in the day If grass is wet the grass catcher is likely to become plugged For efficient bagging air circulation under the mower deck through the chute and into the bag is very important For this reason BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover A CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet as well as the Operator s Manual for the tractor and any
8. be Upper Tube Screw 1 4 x 3 4 mmogou pn Assembly 13 Se o2 Ss tc S c E o c Normal Removal amp Installation A Hitch Support Assembly B Cover K Nut amp Capscrew C Pin L Mounting plate D Hair Pins M Lower Chute Rod E Bag N Lower Chute F Grass Bag Hanger O Pin G Upper Tube P Strap Middle H Middle Tube Q Ridge l Strap Boot R Ridge Cutout J Deflector S Rear Spacers Figure 17 Normal Installation amp Removal Normal Removal amp Installation 4 Lift discharge deflector J up Insert lower chute rod M into mounting plate L Pull strap 1 and Collector Installation secure by placing hole closest to knob in strap Note See previous pages for more detailed completely ovar IOPNTIUP andl GHDSCITON R installation and operation instructions if necessary 5 Slide the upper tube G into cover B aligning 1 Mount the hitch support assembly A Figure 17 ridge Q with cutout R as shown onto rear tractor frame spacers S 6 Slide middle tube H into upper tube G Slide 2 Attach cover B to support assembly using pins C and hair pins D 3 Pivot cover B up Install bags E by attaching grass bag hanger F to support assembly A 14 middle tube H over lower chute N Pull strap P and place hole completely over pin O Collector Removal A WARNING OPERATION WITHOUT BAGGER For operation without bagger the mower deflector MUST
9. could result in serial injury or death A CAUTION This indicates a hazard which if not avoided might result in minor or moderate injury Hazard Symbols and Meanings a Remove Key Before Servicing Rotating Parts Do Not Touch Table of Contents wo D Lnd i N D 1 d lt Operator Safety 2 maine se Maa a a a r 2 Operator Safety oii e aa dai no oot norme ra 2 Safety Decals cott a tet eee Gb eoe core oen tra 2 Mowing with the Catcher 3 Before Operation 3 After Operation 3 Storing the Catcher 3 AssemDly oL Rise Eng ME Sk ruris 5 Install Mounting Plates amp Spacers Broadmoor 1600 2600 LT Series 5 Install Mounting Spacers Conquest 1700 2700 YT Ro amp Prestige 1800 2800 GT Series 5 2 3 Remove Blowout Baffle 6 Install Baffles nn achet tie Rx Db ode aw cd ceca bane al ahs 7 o Install Components cx Fert reet aed o T ne 8 3 Install Bag and Cover Support 10 S S Install Hitch and Upright Support Assembly 10 Install Cover Assembly 10 Install Collector Bags 11 Install Lower Discharge Chute
10. lock 5 16 18 x 3 4 LH side 24 7 8 long LH side 27 3 4 long Figure 5 Baffle Chart af S A Carriage Bolts 5 16 18 x 5 8 B Carriage Bolt 5 16 18 x 5 8 C Carriage Bolts 5 16 18 x 5 8 D Carriage Bolts 5 16 18 x 5 8 E Locknut 5 16 18 F Right Hand Baffle G Left Hand Baffle H Discharge Chute Figure 6 Install Baffles Install Components INSTALL LOWER CHUTE ROD AND PIN TO BOOT 1 Insert the head of pin A Figure 8 through front eee R hole of lower chute D Secure with 1 4 20 x 5 8 1 Install mounting plate A Figure 7 to mower deck carriage bolt B and 1 4 20 lock nut C as as shown Secure with 5 16 18 x 5 8 carriage shown bolts C and 5 16 18 locknuts A 2 Install the rod H to lower chute D using 5 16 18 x 1 capscrew J and 5 16 18 locknut G for front holes Use 5 16 18 x 1 1 4 capscrew I and 5 16 18 locknut G as shown Tighten hardware 3 Install the rubber strap F onto capscrew I securing with 5 16 18 locknut as shown Figure 7 Install Mounting Plate A Mounting Plate B Locknuts 5 16 18 C Carriage Bolts 5 16 18 x 5 8 Figure 8 Install Lower Chute and Pin to Boot A Pin Latch Carriage Bolt 1 4 20 x 5 8 Locknut 1 4 20 Lower Chute Locknut Center Lock 5 16 18 Strap Rubber Locknuts Whiz Lock 5 16 18 Rod Boot Mount Capscrew Hex Head 5 16 18 x 1 1 4 Capscre
11. provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your rider attachments and mower should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is important The safety decals below are on your product If any decals are lost or damaged replace them at once See your local dealer for replacements TP 600 2562 01 AT SMA periodically for tears holes or weak spots and replace with a new bag that meets manufacturer s durability standards If the mower stalls or the collector chute plugs 1 Disengage the PTO 2 Stop the engine and remove the key 3 Set the parking brake and wait for all moving parts to stop 4 Remove the foreign object or clear the chute with a piece of wood before restarting the engine NEVER place hands into COLLECTOR OR MOWER housing to clear jammed objects Blower OR MOWER may rotate when object is removed For added stability and to prevent tipping or loss of control a Use reduced
12. speed on uneven ground and when turning corners b Reduce loads on hillsides It is recommended that the collection system be kept only half full when negotiating any slopes Start mowing on slopes when the collection system is empty c Mow up and down the face of slopes never across the face of any slope Never operate on slopes greater than 17 6 10 These labels are easily applied and will act as a constant visual reminder to you and others who may use the equipment to follow the safety instructions necessary for safe effective operation Attachment Decal Thrown objects hazard Objects thrown by the mower can seriously injure or kill you Do not open the hopper while the mower blades are turning Do not operate the mower without the complete catcher in place Decal WARNING Thrown Objects Hazard Part Number 1732819 Read and obey all operation and warning decals Mowing with the Catcher Always operate with throttle at full soeed when mowing Grass should be cut often and not too short If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging If grass is long operate with mower in high cutting position for first pass cutting again in a lower position on a second pass Do not open the cover with mower engaged If a large amount of cut grass is spilling out from under deck the tube may be plugged or
13. w Hex Head Thin 5 16 18 x 1 crommgo cu INSTALL HANDLE TO TUBE 1 Install handle A Figure 9 using 1 4 20 x 1 2 screw and 1 4 20 locknut B for rear hole Use 1 4 20 x 1 screw D as shown Tighten hardware 2 Install strap E to screw D securing with 1 4 20 locknut F a s S NASCE X D g ge Dx RN n N A d B A n Figure 9 Install Handle to Tube Handle Locknuts KEPS 1 4 20 Screw Slotted 1 4 20 x 1 2 Screw Slotted 1 4 20 x 1 Strap Rubber Locknut Center Lock 1 4 20 mmogoo p INSTALL BAG AND COVER SUPPORT INSTALL COVER ASSEMBLY 1 Install the bag and cover support B Figure 10 to 1 Attach cover assembly B Figure 12 to bag upright support A using reinforcement plate C support bracket A using hinge pivots E Secure and 3 8 16 x 1 capscrews D and 3 8 16 locknuts cover using cover hinge pins C and hair pins D E as shown as shown a Figure 10 Install Bag and Cover Support Figure 12 Install Cover Assembly A Upright Support A Bag Support Bracket B Bag and cover Support B Cover Assembly C Reinforcement Plate C Cover Hinge Pins D Capscrews 3 8 16 x 1 D Hair Pins E Locknuts 3 8 16 E Hinge Pivots INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY 1 Attach hitch and upright support assembly A Figure 11 to frame spacers B as shown NY Figure 11 Attach Hitch and Upright
Download Pdf Manuals
Related Search