Bretford 7088M User's Manual
Contents
1. Code error rate lt 1 1000000 Remote control distance lt 20m Marximum effective handset for one screen s5pic Control signal RF 433 92MHz IR 38KHz Maximun effective time of one press button 120 st2 Minimum effective time of one press button 0 3 s OPERATION When screen plug in the power LED indicator on remote control box will be lighted Press Up button you will hear du Screen will go up until to the maximum effective time Press Down button you will hear du Screen will go down until to the marximum effective time Press Stop button screen will stop When screen is going up press Down button screen will stop press Down button again Screen will go down When screen is going down press up button screen will stop Press Up button again screen will go up if run time of motor is longer then the marimum effective time controller will cut off the Power of motor SETTING SSS Press the SETUP hole of remote control box for more then 6 second after hearing du du du This remote control box is reset Press the SETUP hole again after hearing du du remote control box is in set up status HANDEST LOCK In set up status press Stop button of handset after hearing du du the Up and Down buttons of handset will be locked sz Press Stop button of handset again or screen plug in the power again the Up and Down buttons of handset will be releaset REMOTE2. CONTROL BOX LOCK z In set up status press Stop button of remote control box after hearing du du the Up and Down buttons of remote control box will be locked press Stop button of remote control box again or screen plug in the power again the Up and Down buttons of remote control box will be released MATCHING In set up status press up button of remote contro box or an effective handset after hearing du du remote control box is maching status Press any button of any handset that you want to match with this remote control box after hearing du this handset is matched with this remote control box then the remote control box is out of set up status if no operation 8 seconds then the remote control box is out of set up status Maximum 5 handsets could be matched with one remote control box Reenter the set up status and repeat the matching steps EXCHANGING THE UP AND DOWN BUTTON In set up status press Down button of remote contro box or an effective handset after hearing du du the Up and Down button function of handset and remote control box are exchanged l MEMORY FUNCTION SETTING Press Down button screen will go down when reaching to your required position press Stop and Down button at the same time screen will remember this position later screen will stop at this position automatically T CLEAR Press Up and Down button at the same time clea
3. black borders pull down the middie fi a part of the slat bar smoothly and slowly a vases Press the up button of the switch or the hand set the screen will go up smoothly Press the stop button when the screen goes up to the expected position otherwise the screen will roll back to the housing THE ATTENTION me t s no good for over operating screen which will break the useful life of screen sais Do not pull the contro wires which avoid disconnection and dangers ws Keep the good connection of plug and power ss Cut off the power supply when the screen won t be used for long time TROUBLE SHOOT Always call qualified engineer for maintenance to avoid dangers Always unplug the power supply first before disassemble the screen Check power whether or not is provided wee Check the fuse whether or not is broken Check wire connection a if remote control does not work well please check the battery and replace new one ELECTRIC CONNECTION lf your motorized screen with switch control please refer the below diagram electrical connections AC 110V 60HZ MICRO SWITCH if your motorized screen with remote control please refer the below diagram electrical connections AG 220V 50Hz AC ZOVEOHZ PLUG MICRO SWITCH THE REMOTE CONTROLLER TECHNICAL DATA AC 110V 60Hz AC HOVIH Input 230VAC410 50Hz or 110VAC 10 60Hz Output current to motor lt 1A 230VAC or 110VAC
4. ions illustrated above Bretford recommends using a qualified professional installer BRETFORD BRETFORD 11000 Seymour Avenue Franklin Park IL 60131 P 800 521 9614 F 800 343 1779 www bretford com 031 7074 feher 02 08 INSTALLATION INSTRUCTION mt Unpack the screen carefully be sure the screen is in good condition check all the accessories are packed inside the carton wax Check the voltage and frequency marked on the screen is in accordance with the local power supply It is suggested only to use the screens indoor under normal temperature and humidity s Refer the fig below to fix the screen to the wail or to the ceiling FIX THE SCREEN TO THE WALL FIX THE SCREEN TO THE CEILING __NOLTAGE AND FREQUENCY Choose the voltage acoording to the local requirement 110V 60Hz or 220V 50Hz aided TALEATON MOTE s Must be installed from direct sunlight sma Proper ventilation place Proper dampness Clear place Avoid violent jarring w Avoid the direct air current from air condition heater etc Do not expose the screen in the High or Low temperatme condition Plug in the power supply Press the down p button of the switch box or the hand set the screen will go down smoothly Press the stop button when the screen goes down to p the expected position otherwise the screen i will stop at the lower limited position automatically am Screen stop but the screen size do not meet the right
5. o Installation amp Operation Instructions Electric Wall Projection Screens 7088M 7000M 7022M Thank you for choosing a Bretford Screen fixed using suitable hardware Bretford Screens with Matte White fabric are designed to Hardware f fixings for attaching your screen to the wall or give you a bright sharp image from a wide variety of the ceiling are not included Your installer has the projectors gt responsibility to use the correct hardware For your new electric screen Bretford provides the Protect your new Screen by keeping it rolled into the appropriate wall brackets to attach your screen to the protective case when not in use Always examine the wall If your screen is to be hung by any other method surface for dust amp dirt before retracting the fabric into the than indicated in these instructions it must be adequately case Carefully wipe clean with a soft cloth or duster Please note mounting screws not included Your instaffer will determine the Mounting Bracket type of fasteners needed Nut Plate Insert into bracket amp align holes with screen casing End Cap 640 Ta cues Alten Head Wrench SS Screen Casing es oy Allen Head Bolts Installation Locate your screen where the audience can best see it and where other furnishings in the room permit Mount the screen so that the bottom of the fabric when fully extended is above the heads of the audience Follow the installation instruct
6. r the memory screen will stop at the bottom position PROBLEM AND SOLUTION sei Remote control box not workable LED indicator not light check power supply check fuse in the remote control box Remote control box working well handset not working well w matching handset again or change new handset Up and Down button on remote contro box or handset not working well Release the handset lock or remote conirol box lock Screen could not go down to bottom position clear the memory 4 D0WN SINNER KEY REMOTE CONTROL BOX HAND SET
Download Pdf Manuals
Related Search