Bradley Smoker HN200 User's Manual
Contents
1. HN200 Valve Right Seat Left shown Valve Left Seat Right is opposite 36 x 36 enclosure is not provided as standard equipment IMPORTANT Read the entire installation manual to ensure proper installation of your HN200 shower This manual covers all of the HN200 variations and options available including shower seat and curtain installation Simply omit the steps which do not apply to the unit you are installing Valve Left Seat Right version is shown throughout this manual Valve Right Seat Left is opposite Plumbing contractor shall be responsible for installing shower face plate at the correct height to meet accessibility requirements This installation manual and parts list should be filed by the owner s maintenance department 215 1189 Rev F EN 02 342 Page 1 of 8 Installation Instructions ADA Compliant HN200 Recess Mounted amp Shower with nine e Equa Flo Accu Zone Infrared Control Thermostatic Control Single Valve Air Metering Valve Touch Time or Touch Time w Battery Table of Contents Pre Installation Information 2 HN200 Components 3 HN200 Shower Stall Dimensions 3 Installation Instructions 4 7 Cleaning Instructions 7 Shower Seat Repair Parts 8 Shower Curtain Repair Parts 8 P O Box 309 Menomonee Falls Wi 53052 0309 TEL 1 800 BRADLEY FAX 2622. X 2 Mount one shower rod flange 80 2032mm from the floor as close to the opening of shower stall as possible with two 10 13 x 2 Phillips head screws provided see Figure 6 e Insert one end of the shower rod into the flange e Slide the other shower rod flange onto the shower rod 3 Position the shower rod and flange at the same dimensions as the first flange but on the opposite side of the shower stall opening 4 Secure the flange to the wall with two 10 13 x 2 Phillips head screws provided 5 Install the ten hooks onto the curtain rod and hang the curtain onto the rod Bradley Corporation 215 1189 Rev F EN 02 342 ADA Compliant Recess Mounted Shower Installation Instructions HN200 Cleaning and Maintenance Instructions for Stainless Steel Material Description Stainless steel is extremely durable and maintenance is simple and inexpensive Proper care particularly under corrosive conditions is essential Always start with the simplest solution and work your way toward the more complicated Routine cleaning Daily or as often as needed use a solution of warm water and soap detergent or ammonia Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging the finish Stubborn Stains To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball stainless steel cleaner or a soft abrasive Always follow the manufactures ins
3. 251 5817 http www bradleycorp com ADA Compliant Recess Mounted Shower HN200 Installation Instructions Pre Installation Information CAUTION This shower system may not protect the user from scalding if other temperature controlling devices in the plumbing system should fail CAUTION Excessive heat to the Equa Flo valve body will damage its internal parts Overview The Bradley ADA compliant HN200 comes assembled for job site installation When installed in a 36 x 36 stall the HN200 provides a shower which meets ADA accessibility codes Check local codes for dimensional compliance Components Face Plate Material The shower control panel is constructed of stainless steel Valve and Component Material All exposed parts except seat cover are stainless steel or polished chrome plated brass Valve bodies are brass casting Barrier Free Seat Folding shower seat is constructed of molded plastic with a load capacity of 250 Ibs Shower Curtain Vinyl shower curtain comes with stainless steel curtain rod and hooks Supplies required for installation e 1 2 NPT hot and cold or 1 2 NPT tempered water supplies e 12 1 4 wall anchors and 1 4 20 x 3 4 screws to install shower face plate assembly to wall e 6 wall anchors for 1 4 20 x 1 1 4 hex socket screws to install grab bar grab bar is designed to sustain a concentrated load of 300 pounds e 7 wall anchors for 1 4 x 1 2 Type AB sheet metal screws to mount shower
4. seat HN200 Recess Mounted Shower Warranty Bradley Corporation warrants to commercial and institutional purchasers only each unit free from defects in material and workmanship under normal use and service upon the following terms and conditions 1 This warranty is limited to replacing or repairing at our option transportation charges prepaid by the purchaser any Bradley unit or part thereof which our inspection shall show to have been defective within the limitations of this warranty 2 The period during which HN200 Shower components are warranted is one 1 year measured from the date of our invoice 3 This warranty does not cover installation or any other labor charges and does not apply to any units which have been damaged by accident abuse improper installation or improper maintenance 4 The replacement or repair of defective units as stated in this warranty shall constitute the sole remedy of the purchaser and the sole liability of Bradley Corporation under this warranty Bradley Corporation shall not otherwise be liable under any circumstances for incidental consequential or indirect damages caused by defects in the repair or replacement thereof 5 This warranty extends only to commercial and institutional purchasers and does not extend to any others including consumer customers of commercial and institutional purchasers 6 This warranty is in lieu of all other warranties express or implied including any implied war
5. holes as a template mark the three mounting locations on the wall 3 Install appropriate anchors supplied by installer for 1 4 sheet metal screws in the wall at the three mounting locations 4 Mount the shower seat to the wall with the SCRIBED Figure 4 three 1 4 sheet metal screws supplied at the anchored mounting locations e Position the seat support tube in the support bracket as shown in Figure 5 The tube should rest on the bottom of the front plate FOLDING SHOWER SEAT Figure 5 MOUNTING LOCATION SEAT NOTE When seat is properly installed it should decline downward from back to front 2 to 3 for water drainage 5 Place the support bracket against the wall and adjust the bracket vertically until the shower seat is level in down position e Using the mounting holes on the support SUPPORT BRACKET MOUNTING BRACKET bracket as a template mark the four mounting locations on the wall 6 Install appropriate anchors supplied by installer for 1 4 sheet metal screws in the wall at the four mounting locations 7 Mount the support bracket to the wall with the four 1 4 sheet metal screws supplied at the anchored mounting locations Step 5 Install curtain rod 1 Measure and cut the stainless steel curtain rod to fit the shower stall opening 36 914 Ke SHOWER ROD FLANGE 80 2032 Q TO FLOOR SHOWER STALL OPENING Figure 6
6. icate a type of cleaner This does not constitute an endorsement nor does the omission of any brand name cleaner imply its inadequacy Many products named are regional in distribution and can be found in local supermarkets department and hardware stores or through your cleaning service It is emphasized that all products should be used in strict accordance with package instructions Bradley Corporation 215 1189 Rev F EN 02 342 7 ADA Compliant Recess Mounted Shower HN200 Shower Seat Repair Parts 158 010 Left Hand Plastic Seat Valve Right 158 011 Right Hand Plastic Seat Valve Left Installation Instructions A18 020L LEFT SEAT SHOWER SEAT P10 634 LEFT RETAINER P10 635 RIGHT 270 043 RETAINER SCREWS P10 120 FRAME TUBING j L RETAINER WASHERS A18 020R RIGHT SEAT e P10 449 a BAG of 7 MOUNTING SCREWS BRACKET P18 057 801 255 Shower Curtain Repair Parts Curtain Pre pack S30 068 ITEM PART NO DESCRIPTION QUANTITY 1 170 006 Vinyl Shower Curtain 1 170 006D Duck Shower Curtain 170 006E Herculite Shower Curtain 2 151 001 Curtain Hook 10 3 269 367 Curtain Rod 1 4 150 157 Shower Rod Flange 2 5 P10 412 10 13 x 2 Phillips Head Screw 1 Bag 4 Screws Bradley Corporation 215 1189 Rev F EN 02 342
7. m go yes ean 381mm TYP po 7 1 2 45 1143mm WALL OPENING OUTLINE 191 mm Figure 1 508mm NOTE WALL OPENING RECESS TO BE 4 102mm DEEP Installation Instructions 1 2 NPT SUPPLIES NOTE Due to differing state codes if the valve height is different from the indicated 43 1091 mm all dimensions within the symbol must be changed by the same amount Example If the code approved height is 40 then 43 1091mm 40 1015mm 3 76mm Result Subtract 3 76mm from all dimensions within the symbol Bradley Corporation 215 1189 Rev F EN 02 342 ADA Compliant Recess Mounted Shower Installation Instructions Installation Instructions continued Step 2 Make plumbing connections NOTE Hoses need to be connected to 1 2 NPT pipe supply before the shower is fastened to the wall 1 Make water supply connections to the stainless steel hoses see Figure 2 Equa Flo and Thermostatic 1 2 NPT Hot and Cold supplies Single Valve Accu Zone Infrared Control Air Valve and Touch Time 1 2 tempered supply Step 3 Install face plate and grab bar 1 Secure the grab bar to the six wall Position the face plate on the wall Mark the wall and install twelve wall anchors suitable for use with 1 4 20 x 3 4 button head Allen key screws see Figure 3 Attach the face plate to
8. ranty of merchantability or fitness for a particular purpose or otherwise 2 Bradley Corporation 215 1189 Rev F EN 02 342 Installation Instructions HN200 Components and Shower Stall Dimensions Inline Backflow Preventer Quick Disconnect Stainless Steel Hose Hand Held Hose Spray with Post Style Bracket Recessed Soap Dish ADA Compliant Recess Mounted Shower HN200 Elbow with Flange Showerhead Diverter Valve Shower Valve Equa Flo shown Shower Face Plate Assembly No Grab Bar 53 184 18 457mm Yi A E par 381mm 7 il J aa V an max 4 36 emmy 914mm VALVE LEFT SEAT RIGHT NOTE Compliance and conformity to local codes and ordinance is the responsibility of the installer 18 457mm 4 914mm 102mm min VALVE RIGHT SEAT LEFT Bradley Corporation 215 1189 Rev F EN 02 342 ADA Compliant Recess Mounted Shower HN200 Installation Instructions NOTE Flush the supply lines before making connections NOTE Install the supply inlets no lower than 48 and no higher than 60 off of finished floor Step 1 Rough in piping for shower NOTE When facing the wall the supply pipe to the left of the centerline is HOT 1 Rough in 1 2 NPT hot and cold water supply piping for valve at the dimension shown in Figure 1 piping supplied by installer BACK WALL je 18 457m
9. the wall with twelve 1 4 20 x 3 4 button head Allen key screws provided see Figure 3 Attach the grab bar to the wall e Position the L of the grab bar to fit the back wall of the shower stall Use the flange as a template and mark the six screw hole locations and install six anchors supplied by installer for HN200 Figure 2 VALVE LEFT SEAT RIGHT screws see Figure 3 1 4 20 x 1 1 4 flat head Allen key anchors using six 1 4 20 x 1 1 4 flat head Allen key screws provided by installer see Figure 3 NOTE ALL WALL ANCHORS SUPPLIED BY INSTALLER Ss 1 4 20 x 3 4 BUTTON HEAD ALLEN KEY SCREW 12 PLACES 160 143 FACE PLATE GRAB BAR 853 184 1 4 20 x 1 1 4 FLAT HEAD ALLEN KEY SCREW Figure 3 VALVE LEFT SEAT RIGHT Bradley Corporation 215 1189 Rev F EN 02 342 ADA Compliant Recess Mounted Shower HN200 Installation Instructions continued Step 4 Mount shower seat NOTE All anchoring devices supplied by installer must be carefully selected to insure adequate support for Installation Instructions the shower seat given the type of wall construction 1 Measure and scribe a horizontal line 16 1 16 above the finished floor see Figure 4 2 Position the folding shower seat against the wall with the three mounting holes on the seat centered on the scribed line e Using the mounting
10. tructions and apply in the same direction as the polish lines IMPORTANT NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON STAINLESS STEEL ALWAYS USE STAINLESS STEEL WOOL OR STAINLESS STEEL BRUSHES Special Situations for Material Fingerprints and Smears To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance with the manufactures instructions Many of these products leave a protective coating the helps prevent future smears and fingerprints Grease and Oil To remove grease and oil use a quality commercial detergent or caustic cleaner Apply in accordance to the manufactures instructions and in the direction of the polish lines Precautions Avoid prolonged contact with chlorides bleaches salts bromides sanitizing agents thiocyanates pesticides photography chemicals and some foods and iodides on stainless steel equipment especially if acid conditions exist IMPORTANT DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON STAINLESS STEEL The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting Look for the actual source of the rust in some iron or steel particles which may be touching but not actually a part of the stainless steel structure NOTE Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear The use of these cleaners should be avoided Brand Names Use of brand names is intended only to ind
Download Pdf Manuals
Related Search