Bosch EX12LED User's Manual
Contents
1. Directive This installation should be made by a qualified service person and conform to all local codes EXTREME CCTV will not be responsible for injuries or damages resulting from the improper installation or use of any product sold by EXTREME CCTV their agents distributors or dealers NOTE This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmtul interference in a residential installation As part of its normal operation this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may cause interference to radio communications However there is no guarantee that interference will not occur on a particular installation If the device does cause interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures 1 Fit Ferrite beads on all cable to and from the power supply box within the box walls 2 Route the composite cable between the camera and the power supply in steel conduit piping over the entire run of the cable up to and including connection to a deep conduit base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box 3 Contact BOSCH Service Center for further advice INDEX EX72LED Page EES COU2. IGURE 1 3 Rear View 2 INPUT POWER CONNECTIONS Reference Only The voltage operating range Is 12 24AC DC Note input leads are not polarity dependent LED Power VRB Power Input Input FIGURE 2 1 Voltage Regulator Board VRB 3 MOUNTING ILLUMINATOR UNIT select a suitable location that is protected from accidental damage tampering and environmental conditions exceeding the LED s Specifications Caution The selected mounting location should not place the camera in a situation where its environmental specifications could be exceeded See page 17 Ensure the selected location is protected from falling objects accidental contact with moving objects and unintentional interference from personnel Follow all applicable building codes be followed The following installation guidelines must Locate the camera such that it cannot be easily interfered with either intentionally or accidentally select a mounting surface capable of Supporting the combined weight of the Camera and mounting hardware under all expected conditions of vibration and temperature e secure all cabling e Installations on drywall must use a 1 bolt and drywall butterfly tyoe anchor or superior connection The EX12LED can be mounted to any flat surface The supplied U shaped mounting bracket allows for tilt as well as rotation If this mounting bracket does not suit the needs of the installation the installer can utilize e
3. Ol reens EO 1 Vlore ae P NE E 2 PS E S ER E EE TEA 2 Items Required for Installation 00 2 Initial Preparations ccccecceeeeeeeeeeeeeeeeees 3 GUIG CIOS rete cscicee een seinesttesisiea cee leche casiesedewosun 3 section 1 Mechanical Specifications 4 section 2 Inout Power Connections 7 section 3 Mounting Illuminator Unit 8 section 4 LED Adjustments 11 section 5 Illuminator Re Assembly 13 section 6 Troubleshooting Guide 15 section 7 General Specifications 17 DESCRIPTION The EX12LED Infrared LED I luminator provides night time covert lighting for short range indoor and outdoor surveillance when used in conjunction with existing or newly installed monochrome cameras Its compact Cube shape is comprised of 42 LEDs mounted into a solid core CNC machined aluminum housing and beamed through a dark tinted tough window The EX72LED has an effective range up to 40 feet and is available in 850nm or 940nm with 30 or 60 beam spread A voltage regulator circuit allows for 12 24ac dc a range operation also providing protection trom voltage surge transient spikes and reverse voltage The EX12LED is available in several models designed to meet specific needs See the Light Get the Picture m UNPACKING Care should be taken when unpacking the shipped unit Check the parts list and confirm all items have been lo
4. Precision Engineered Opto Electronics INSTALLATION INSTRUCTIONS EX12LED Infrared LED Illuminator MAN 12LED 06 10 IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep this instruction Heed all warnings Follow these instructions Do not use this apparatus near water Clean only with dry cloth Install in accordance with manufacturer instructions Do not install near any heat sources over manufacture specification temperature Only use attachments accessories specified by the manufacturer Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in a way such as the apparatus has been exposed to rain or moisture does not operate normally or has been dropped IMPORTANT For best results please read this Instruction Booklet prior to installing the EX12LED Illuminator Unit WARNING CSA Certified UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety standards Certified to C Extreme CCTV GR UL 50 UL 2044 CSA C22 2 No 0 M1991 Made in Canada us CSA C22 2 No 1 M94 CSA C22 2 No 94 M91 189936 CSA Type 4X NEMA 4X CSA C22 2 No 94 M91 12 Vdc 9W max NEC Class 2 Limited Power Circuit See Installation 24 Vac 60 Hz 9 W max instructions For Proper Connections EU Directives covered by this declaration 72 9 EC Low Voltage Directives 89 336 EEC Electromagnetic Compatibility
5. are at full turn 7 GENERAL SPECIFICATIONS LED Type High Perf 850nm 940nm LED Beam Angles 60deg W 30deg M Operational Rang 20 C to 50 C 4 F to 122 F Humidity Range Up to 85 relative Power Supply 0000 12V dc or 24V ac 60Hz 9W Viewing WINdoW s sesososesnenennnnnrenennn Acrylic POUSO e CNC Aluminum Anodized DIMENSIONS W 2 875 73 0mm H 2 750 69 9mm D 2 750 69 9mm WORT oaair aen 1 0 Ibs 454g Subject To Change Without Notice 16 Americas Bosch Security Systems Inc 850 Greenfield Road Lancaster Pennsylvania 17601 USA Telephone 1 888 289 0096 Fax 1 585 223 9180 Email security sales us bosch com www boschsecurity us Europe Middle East Africa Bosch Security Systems B V P O Box 80002 5600 JB Eindhoven Netherlands Phone 31 40 25 77 284 Fax 31 40 25 77 330 emea securitysystems bosch com www boschsecurity com Asia Pacitic Bosch Security Systems Pte Ltd 38C Japan Pemimpin Singapore 577 180 Phone 65 6319 3450 Fax 65 6319 3499 apr securitysystems bosch com www boschsecurity com Bosch Security Systems Inc 2009 Data subject to change with out notice 1 7
6. cated Inspect the equipment thoroughly to ensure nothing was damaged in transit Contact BOSCH Service Center if a problem is noted see the rear page of this booklet for contact numbers PARTS LIST items supplied with unit EX12LED Unit including one U shaped mounting bracket with fasteners Installation Instructions booklet ITEMS REQUIRED FOR INSTALLATION Not supplied with unit Philips screwdriver Small slotted screwdriver Mounting screws etc INITIAL PREPARATIONS gt The EX72LED operates in either Vdc or Vac mode The power input supply voltages can be 12 24VAC DC see Section 2 Inout Power Connections Reference Only Determine the optimum location for the Illuminator unit See Section 3 Mounting I lluminator Unit All units have been tested prior to shipment but it is advisable to check the unit s operation before installation GUIDELINES The installation and set up of the EX72LED is explained in Sections 3 and 4 It is important that these steps are followed in sequence 1 MECHANICAL SPECIFICATIONS See Section 7 General Specifications for additional information 2 150 69 9mm 4 2 8 5 73 0mm 2 750 69 9mm E FIGURE 1 1 Outline Dimensions Mounting Bracket Viewing Tilt Adjustment Window Screws FIGURE 1 2 Front View Photocell Mounting Holes for U Bracket NS 1 4 20 threaded holes for standard camera type mounting brackets F
7. e the gasket is properly seated and the photocell is centered in its viewing window see Figure 5 1 on page 14 Attach the rear cover to the housing Ensure the power cable has enough Slack so that It is not stressed or crimped when the EX72LED unit is fixed into its final mounting position 12 Make sure the photocell Slides into the round hole in the plastic D gt window Gasket FIGURE 5 1 Rear Cover Re Assembly 6 TROUBLESHOOTING GUIDE PROBLEM Fuse Blows Don t know if LEDs are ON LEDs are not ON POSSIBLE SOLUTION Check fuse rating Check for shorting between the enclosure and the input power 850nm LEDs will have a faint red glow when ON 940nm LEDs are covert Aim the LEDs directly at an IR sensitive camera to see the lights or wait for the LEDs to warm up two minutes Feel for warmth Cover the photo sensor to activate power to the LEDs up to 30 seconds delay for activation Adjust the photocell s variable resistor towards the ON position Adjust oower to the LEDs PROBLEM POSSIBLE SOLUTION LEDs are not turning Make sure the photo OFF when sufficient sensor is not covered or ambient light is present hidden behind any object Check that the photocell is recessed in the viewing window Adjust the photocell s variable resistor towards the OFF position The LEDs will stay ON or OFF if the adjustments
8. ither of the two 14 20 camera mount holes located in the housing see Figure 1 3 on page 6 The choice of camera type mounting brackets is left to the installer step 3 1 Mount the U bracket to the chosen mounting surface and attach the EX12LED with the supplied adjustment screws see Figure 3 1 on page 10 step 3 2 Tighten the EX72LED into its approximate viewing direction Proceed to Section 4 Mounting Bracket Mounting Surface Alternate Position for Mounting Bracket Tilt Adjustment Screws fn ERRA EEA AES E A Alternate Mounting Surface Note The Tilt Adjustment screws should be loosened only Do not remove these screws FIGURE 3 1 Mounting Details 10 4 LED ADJUSTMENTS Note The current setting of LED is 0 9A by manufacturer default End user not advisable for adjustment For photocell On Off light level adjustment rotate VR2 Clockwise is off and counter clockwise is on Photocell On Off Adjustment FIGURE 4 1 LED and Photocell Adjustments 11 5 ILLUMINATOR UNIT RE ASSEMBLY Make sure the input power wires are properly connected and tightened into the terminal block all holes are sealed against moisture penetration and all mounting screws are tight Step 5 1 Step 5 2 Step 5 3 Step 5 4 Check the gasket attached to the rear cover plate has not been dislodged or warped Gently press the rear cover into place making sur
Download Pdf Manuals
Related Search