Bosch F.01U.278.516 User's Manual
Contents
1. gt Select the locating mode and the identification number See Section 4 2 First use Assistance and fire priority This sets the assistance call and the fire alarm as priority calls that will be displayed first Type the code 123991 The unit plays a melody and a confirmation message is displayed Assistance and fire non priority This command sets the assistance call and the fire alarm as non priority calls This means that the last alarm is displayed whatever its type This is the default value Type the code 123992 The unit plays a melody and a confirmation message is displayed F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit 5 5 1 5 2 Bosch Security Systems Operation en 21 Operation Adjusting the loudspeaker volume When the Relay Unit is in standby mode gt Press to increase the volume gt Press to decrease the volume Consulting the alarm or event buffer The Relay Unit uses an alarm buffer and an event buffer for display indication The following alarms and messages are stored into the alarm buffer Call for help call for assistance reserve call call for help 2 technical call fire alarm battery low message error message disconnection of a Relay Unit from the RS 485 bus If alarms are repeated only the least recent entry remains in the buffer The call for assistance replaces the call for help the reserve call and the technic2. 15 16 17 18 18 18 18 18 18 18 19 19 19 19 20 20 20 F 01U 278 516 V1 0 2012 11 4 en Table of Contents 4 3 3 Assistance and fire priority 4 3 4 Assistance and fire non priority 5 Operation 51 Adjusting the loudspeaker volume 5 2 Consulting the alarm or event buffer 9 21 Switching between alarm and event buffers indication 5 2 2 Display indications 5 2 3 The green button does not work 5 2 4 Disconnecting a Relay Unit 6 Maintenance 6 1 Checking the system 6 2 Monitoring the power supply 6 3 Monitoring the backup battery 6 4 Cleaning 6 5 Parts replacement 6 5 1 Disassembling the unit 6 5 2 Backup battery replacing 7 Disposal 7 1 Disassembly 1 2 Returning to the manufacturer 1 3 Materials 1 4 Battery A Appendix A 1 Electrical specifications A 2 Dimensions and weight A 3 Environmental conditions A 4 List of criteria A 5 Connectors A 5 1 LINE socket unit bottom A 5 2 Power socket unit bottom A 5 3 RS 485 socket unit rear F 01U 278 516 V1 0 2012 11 User Manual Relay Unit 20 20 21 21 21 22 22 23 23 24 24 24 24 25 25 25 26 27 2 2 2 2 28 28 28 28 29 30 30 30 30 Bosch Security Systems Relay Unit 1 1 1 2 1 3 1 4 GP Do Bosch Security Systems Safety instructions en 5 Safety instructions NOTICE The user and installer should read and understand this chapter before any intervention on the Relay Unit Impor
3. or the Red button to erase any previous selection The black box remains 5 6 Connect the Relay Unit to the RS 485 bus Press ox or the Green button to enable the automatic attribution The next free identification number is attributed by the Main Unit and is displayed on the Relay Unit at the bottom right User Manual F O1U 278 516 V1 0 2012 11 Bosch Security Systems 20 en Programming 4 3 4 3 1 4 3 2 4 3 3 4 3 4 Relay Unit Manual selection of the Main Unit 5 a Scroll with and to set manually the identification number Confirm with or the Green button The Relay Unit signalizes that it is not connected to the RS 485 bus 5 b Connect the Relay Unit to the RS 485 bus The number is now visible at bottom right Special settings After pressing 0 three times quickly you can enter special codes Displaying the firmware version gt Type the code 194155 The version of the firmware will be displayed for a few seconds Resetting all the parameters and buffers NOTICE This resets the Relay Unit to its original factory settings erasing all the parameters alarms and events buffers It is mandatory if you change the locating mode or the identification number Disconnect the RS 485 bus before performing a reset Reconnect it afterwards gt Type the code 194156 The unit resets plays a melody and displays a message gt After afew seconds the unit goes back to the first use display
4. V1 0 2012 11 8 en Description Relay Unit 2 1 2 Bottom view 1 Identification label 2 Cable channels 3 Wall mounting holes Distance between holes is 6 2 in 157 mm See Section 3 2 3 Wall installation page 14 for a detailed description 4 ON OFF switch 5 LINE socket used for firmware update See Section A 5 1 LINE socket unit bottom page 30 for wiring 6 10V AC socket See Section A 5 2 Power socket unit bottom page 30 for wiring F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit Description en 9 2 1 3 Front view 1 LED Indicator LED Standby mode normal operation Green permanent Backup battery low Green blinking Power supply disconnected Green flashing Help assistance or fire Red blinking 2 1 4 Relay Unit rear view 1 RS 485 connector See Section A 5 3 RS 485 socket unit rear page 30 for wiring 2 Antenna connector Bosch Security Systems User Manual F 01U 278 516 V1 0 2012 11 10 en Description Relay Unit 2 2 Detailed description 2 2 1 Loudspeaker When one of the following alarms or messages is received by the Relay Unit the internal loudspeaker is activated until acknowledgement Loudspeaker Power supply disconnected Dual tone beep every minute Call for help reserve call technical call 4 second interval one tone Error message 1
5. 2 4 2 1 4 2 2 4 2 3 First use List of original factory settings Parameter Original Factory Setting No Locating mode and identification number are set at first use To change a value reset the 19 we dS 20 1 unit See Section 4 3 2 Resetting all the parameters and buffers page 20 Parameters set by the Main Unit The parameters listed below are programmed in the Main Unit and are applied to the Relay Unit See the Main Unit user manual Display mode Unit language Date and time Local acknowledgement and the access code Output relay function and mode Locating mode and identification number 1 Disconnect the Relay Unit from the RS 485 bus 2 Switch the Relay Unit on with the switch located at the bottom of the unit Wait for the following display to appear 3 Enable ON or disable OFF the indication of the transmitter position locating mode on the Relay Unit display It must be the same as in the Main Unit x d nl to disable or j to enable the locating mode o au The identification number of the Relay Unit must now be attributed Q5 A gt Press The identification number is attributed by the Main Unit upon connecting the RS 485 bus corresponds to the order of connection It can also be set manually The range for this value is A B C Y Z a b c d e f for a maximum of 32 Relay Units Automatic attribution by the Main Unit 5 a Press Cc
6. 5 second interval one tone Disconnection of a relay unit from RS485 bus 1 minute interval one tone Call for assistance fire alarm Continuously dual tone beep Local acknowledgement Short beep 2 2 2 Display The Relay Unit is equipped with a 2 x 20 characters display that guides the operator during the programming During normal operation alarms and messages are displayed NOTICE This user manual is written for the unit language English USA Certain displays may differ for the unit language English UK 2 2 3 Keyboard The keyboard has 21 alphanumeric keys They are used to perform special commands or during normal operation anan dc gg bh F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit Description en 11 Increase the volume of the loudspeaker See Section 5 1 Adjusting the loudspeaker volume page 21 Decrease the volume of the loudspeaker See Section 5 1 Adjusting the loudspeaker volume page 21 Scroll down to the previous alarm event See Section 5 2 Consulting the alarm or event buffer Page 21 Scroll up to the next alarm event See Section 5 2 Consulting the alarm or event buffer Page 21 Confirm a value or acommand Cancel an entry or acommand Check the status of the backup battery See Section 6 3 Monitoring the backup battery page 24 Enter a value such as special codes See Section 4 3 Speci
7. Installation Generalities gt Install the Relay Unit in a dry place away from any source of heat Tools required Torx T20 screwdriver Torx T10 screwdriver Installation on a piece of furniture It is recommended to place the Relay Unit on a non slippery surface However do not place anything blanket or lace on top of the unit Wall installation You can fasten the Relay Unit on a smooth wall surface using two screws The distance between holes is 6 2 in 157 mm The power line cord should be placed inside the cable channels on the bottom of the Relay Unit Installing the antenna 1 Use the straight adapter 4 for wall installation or the right angled bended adapter 3 for installation on a piece of furniture 2 Fasten the adapter 3 or 4 on the antenna connector 1 o000O0 o000 3 Fasten the antenna 2 on the adapter F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit Installation en 15 3 2 5 Connecting to the mains The Relay Unit is powered by an adaptor 115 10 VAC CAUTION In case of a different supply the equipment must fulfill isolation requirements according to EN60950 standard last edition 1 Plug the power adaptor into a power outlet placed near the unit It should be easily accessible at any time 2 Connect the cable to the socke
8. Perform periodically an alarm test Monitoring the power supply In case of a power failure the Relay Unit emits a beep and the following message is displayed alternatively with the date and time display The backup battery ensures that the Relay Unit remains operational even in the case of a power failure When fully charged the battery ensures a power backup of 24 hours When power returns after a power failure the battery is recharged If it has been completely discharged it will reach its full capacity after 24 hours of charging time Monitoring the backup battery The status of the battery is indicated on the top right of the display f gt To check the backup battery voltage press fi The following message is displayed NOTICE At startup an automatic check is made During normal operation an automatic check is made every 30 minutes gt If the remaining battery capacity drops below 25 the following message is displayed gt If the Relay Unit detects that the backup battery is defective the following message is displayed NOTICE If the backup battery is defective replace it as described in Section 6 5 2 Backup battery replacing page 26 F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit Maintenance en 25 6 4 Cleaning gt Avoid using cleaning products or detergents gt Wipe off your Relay Unit occasionally with a dry cloth 6 5 Parts replacement 6 5 1 D
9. Relay Unit F 01U 278 516 V1 0 2012 11 BOSCH en User Manual Relay Unit Table of Contents 1 1 1 2 1 3 1 4 1 4 1 2 1 2 1 1 2 1 2 2 1 3 2 1 4 2 2 2 21 2 2 2 2 253 2 2 4 2255 3 1 3 1 1 3 2 3 2 1 3 2 2 23 3 2 4 32 9 3 2 6 3 2 7 4 4 1 4 1 1 4 1 2 4 1 3 4 1 4 4 1 5 4 2 4 2 1 4 2 2 4 2 3 4 3 4 3 1 4 3 2 Safety instructions Importance of safety instructions Disregarding safety rules Environmental conditions General safety instructions Observation and information Description General description Top view Bottom view Front view Relay Unit rear view Detailed description Loudspeaker Display Keyboard RS 485 interface Antenna Installation Unpacking List of contents Installation Generalities Installation on a piece of furniture Wall installation Installing the antenna Connecting to the mains Connecting the RS 485 Setting the 100 Ohm termination jumper Programming Generalities Using the keyboard Exit and cancel entries Key not allowed Locking and unlocking the keyboard Programming time out First use List of original factory settings Parameters set by the Main Unit Locating mode and identification number Special settings Displaying the firmware version Resetting all the parameters and buffers Bosch Security Systems User Manual Table of Contents en 3 9 0101 01 nn 9 O O CO NNN 10 10 10 10 12 12 13 13 13 14 14 14 14 14
10. al call in the alarm buffer In addition to all the alarms all possible entries are stored in the event buffer The following messages are directly stored into the event buffer acknowledgement MIYN46 sent by an MIYN46 Wall Transmitter MIYS35 or MIYS37 Transmitters acknowledgement by MIYS35 or MIYS37 Transmitters local acknowledgement an acknowledgement at the Main Unit or Relay Unit daily message check personnel arrival message A B C and D personnel departure message power outage of a receiver unit return of power at a receiver unit backup battery low of a receiver unit interruption of the RS 232 connection interface between the Main Unit and a PC return of the RS 232 connection interface between the Main Unit and a PC connection of a Relay Unit to the RS 485 bus transmission of the event door by an MIYRAC Wireless Contact NOTICE The alarm and event buffers have a capacity of 18 or 100 entries See the maximum number of events buffered in the Main Unit user manual The event buffer will normally be filled with the last 18 or 100 entries In the alarm buffer only the active alarms are present User Manual F 01U 278 516 V1 0 2012 11 22 en Operation 5 2 1 5 2 2 Relay Unit Switching between alarm and event buffers indication The alarm buffer is indicated by default If you are in the event buffer the unit changes automatically to the alarm buffer after 1 m
11. al settings Page 20 Enter a value or launch the event alarm display mode See Section 5 2 1 Switching between alarm and event buffers indication Page 22 gelte Bel Bosch Security Systems User Manual F 01U 278 516 V1 0 2012 11 12 en Description Relay Unit 2 2 4 RS 485 interface One Main Unit and up to 32 Relay Units can be connected by a RS 485 bus The bus must be connected to pins 2 and 5 of the RS 485 socket gt For connector wiring see Section A 5 3 RS 485 socket unit rear page 30 NOTICE Keep polarity equal when connecting further units to the RS485 bus NOTICE Maximum RS485 bus length 3 900 ft 1200 m Use only one twisted pair cable for the interconnection NOTICE The receiver units located at the two ends of the bus must be terminated with a 100 Ohm resistor See Section 3 2 6 Connecting the RS 485 page 16 for more information about the jumper setting In this configuration you always should connect the Main Unit first The Relay Units must then be connected to the RS485 bus one by one not at the same time Relay output Inthe same connector a potential free contact is available It is a low current switching contact The relay potential free switching power max 48V 0 5 A is activated at a call for help call for assistance or fire alarm This relay can be set as closing or switching contact cycle of 10 seconds on 10 seconds off This feature can be used to drive a signal lamp for ex
12. ample gt For connector wiring see Section A 5 3 RS 485 socket unit rear page 30 gt For relay setting see the user manual of the Main Unit 2 2 5 Antenna The antenna is connected to the Relay Unit using the adapter supplied with the unit gt See Section 3 2 4 Installing the antenna page 14 F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit 3 3 1 3 1 1 Bosch Security Systems Installation en 13 Installation Unpacking The Relay Unit is carefully packed for transportation The components contained in the box are protected but should be handled with care Store the packaging material for further use storage or transport 1 Take all components out of the box and place the Relay Unit on the working space 2 Check each component in the box in accordance with the list of contents below 3 Check that the Relay Unit and its accessories have not been damaged during transportation In case of defective or missing equipment do not try to install the Relay Unit gt Contact immediately your local representative List of contents Relay Unit Power supply adaptor US 115VAC 10VAC 13 4 in Antenna 434MHz 1 2 L 13 4 in 34 cm FME Straight adapter BFME TNC Right angled bended adapter BFME ETNC 6 6 ft 2 m Cable FCC 6 4 Relay Unit User Manual User Manual F 01U 278 516 V1 0 2012 11 14 en Installation 3 2 3 2 1 3 2 2 3 2 3 3 2 4 Relay Unit
13. ble or modify the battery Do not expose the battery to extreme temperatures and never above 140 F 60 C For maximum battery capacity use the battery at room temperature Keep out of reach of children Use the battery for the intended purpose only Do not put the battery in the mouth Battery electrolytes may be toxic if swallowed CAUTION There is a risk of explosion if battery is replaced by a wrong type The battery should be replaced exclusively by authorized personnel Dispose of used batteries according to instructions and regulations Procedure 1 Disassemble the unit as described in Section 6 5 1 Disassembling the unit page 25 Disconnect the battery cable 1 Carefully remove the backup battery 2 Place the new backup battery a Connect the new battery cable 1 F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit D 7 1 1 2 1 3 7 4 Bosch Security Systems Disposal en 27 Disposal The Relay Unit is marked with a crossed out wastebasket symbol This means that at the end of its lifetime the product should be disposed separately from ordinary household waste in accordance with the local regulations The product and its accessories should be delivered to an appropriate collection facility that ensure recycling treatment and an environmentally compatible disposal This prevents any negative impact on the environment and human health and promote
14. ctive MIYN46 pne o P Acknonledaement Sent by MNNG MNS35 or MYS37 pon fa E jDooropenordarclsek ooo mona e pooo o tial Cal wv PERSONNELS fe Ir ooo Ged tey resene a ewe for LE C ete mme E Dag ENDPERSONNEL fo Ir Removed coded key imma oo PERSONNELD fo E eosed key presence Ma o assistance ao po pe panours E enee mees fis Reserve all rng PERSONNELS fa E Gade key presence WINS moer E Bad ado ansmisson noise Acknowledgement Ack Transmitter No 1 PoweR OUTAGE is fe Man Umt or Relay Unit not powered POWERGACK fo E Power back Wain Unit or ely Uni 28 29 30 3l XX 58 I I m m LOW ACCU Accumulator discharged Main Unit or Relay Unit ACK TRANSM 2 Acknowledgement Ack Transmitter No 2 ACK TRANSMS eme ACK TRANSMIS e fe a fe Acknowledgement Ack Transmitter No 3 Acknowledgement Ack Transmitter No 4 Acknowledgement Ack Transmitter No 5 Acknowledgement Ack Transmitter No xx Acknowledgement Ack Transmitter No 32 Dementia Alarm ACK TRANSM xx ACK TRANSM 32 DEMENTIA 60 NOTICE i All events are buffered into the event buffer of the Relay Unit All alarms and events are sent to the printer display All alarms and events except the events COMPUTER OFF and COMPUTER ON are sent to the Alarm management Software Bosch Security Systems User Manual F 01U 278 516 V1 0 2012 11 30 en Relay Unit A 5 A 5 1 A 5 2 A 5 3 Connectors LINE socket unit b
15. e last passed beacon visible in all display modes If no beacon is registered or if the alarm is sent outside of the range of a beacon the POS 000 will be displayed In the alarm buffer the total number of entries is indicated on top at the right You can immediately see how many alarms are active In this example there are a total of three alarms in the alarm buffer In the event buffer the position of the event in the buffer is indicated Here EO1 corresponds to the latest entry in the event buffer Unit displaying the current date and time The green button does not work Problem you have tried unsuccessfully to acknowledge an alarm with the Green button Cause the local acknowledgement is disabled Solution activate the local acknowledgement function See the Main Unit user manual Disconnecting a Relay Unit If a Relay Unit stops communicating with the Main Unit an alarm Relay Off is generated on the Main Unit This alarm can only be acknowledged on the Main Unit by pressing the Green button followed by the code 45 Thereafter an event No Relay is generated As soon as the Relay Unit communicates again with the Main Unit the Event Relay On is generated This operation is independent of the local acknowledgement setting User Manual F 01U 278 516 V1 0 2012 11 24 en Maintenance 6 6 1 6 2 6 3 Relay Unit Maintenance Checking the system Check the correct function of your system gt
16. inute without activity If there are no entries in the alarm buffer the display shows the actual date and time gt To switch from alarm to event buffer and vice versa press ZS ei N ith 1 and gt Scroll the alarms or the events with ors and kon As gt Scroll the alarms only with the Green button Display indications With the Yellow button you can switch between three available information blocks The following information is displayed when an alarm or a message arrives First information block n case of a floor room bed display mode 1 2 HELP Aas FLigiz Bsp BE aei 3 3 3 1 criterion of the alarm or message 2 alarm A or event E followed by its order in the buffer 3 identification of the transmitter location floor room bed numbers Incase of single number display mode 1 2 1 criterion of the alarm or message 2 alarm A or event E followed by its order in the buffer 3 identification of the transmitter location three digits or four signs Second information block date of the event time of the event main unit space or relay Unit A f identification number En quality of the received radio signal This information is visible in all display modes F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit 5 2 3 5 2 4 Bosch Security Systems Operation en 23 Third information block HELP Pose 8 position of th
17. isassembling the unit Removing the antenna 1 Remove the antenna 1 and its adapter 2 or 3 Removing the communication board DANGER Do not damage the battery cable its connector 7 or the serial communication board connectors 1 With a Torx T20 screwdriver unscrew and remove the 4 screws 4 2 With a Torx T10 screwdriver unscrew and remove the screw 5 3 Carefully remove the communication board 6 Bosch Security Systems User Manual F 01U 278 516 V1 0 2012 11 26 en Maintenance 6 5 2 Relay Unit Backup battery replacing Important Safety Instructions The battery should charge for 24 hours before using the Relay Unit for the first time after replacing the battery or after a long power shortage Battery type is 6V NiMH NOTICE The battery will charge correctly between 41 F 5 C and 113 F 45 C A battery that is new or that has not been used for a long time can have reduced capacity at first use A rechargeable battery can be charged and discharged many times However it will eventually wear out This is not a defect It is recommended to replace batteries that cannot ensure a minimum power back up time of 8 hours at full charge CAUTION May explode if exposed to fire Use only original batteries intended for your Relay Unit Do not expose the battery to liquids Do not let the battery s contacts touch another metal This could damage the battery Do not disassem
18. liquid enter the system In case of liquid spill inside the Relay Unit act immediately as follows 1 Switch off the unit using the main switch under the casing Unplug the power supply adaptor Dry up the unit Clean the unit Check that the unit switches on correctly Observation and information In case of defective operation or any other technical incident for which no remedy is described in this manual please contact immediately your local representative F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit 2 Description 2 1 General description 2 1 1 Top view o O ce 9 o 6 E o O O e o 0 0 0 og H Bosch Security Systems o O o o o oo H o oo Description en 7 1 Loudspeaker See Section 2 2 1 Loudspeaker page 10 2 Display See Section 2 2 2 Display page 10 3 Keyboard under the cover See Section 2 2 3 Keyboard page 10 4 LED Indicator 5 Yellow button Used to view more details about the event or alarm currently displayed date and time position etc 6 Green button Used to acknowledge an alarm locally see Section 5 2 3 The green button does not work page 23 7 Red button with light This button is not used Pressing the button does not activate a function The light blinks red during an alarm User Manual F 01U 278 516
19. ocedure see Section 6 5 1 Disassembling the unit page 25 NOTICE If you do not want to disassemble the Relay Unit you also can short out pins 3 and 4 of the connector This has the same effect as the jumper setting described above See Section A 5 3 RS 485 socket unit rear page 30 for connector wiring User Manual F 01U 278 516 V1 0 2012 11 18 en Programming A 4 1 4 1 1 4 1 2 4 1 3 4 1 4 4 1 5 Relay Unit Programming Generalities Using the keyboard gt Open the cover carefully and use the keyboard Toaccess the special settings programming press three times quickly See Section 4 3 Special settings page 20 for more details Exit and cancel entries gt Press Cc once or several times Key not allowed If you have pressed a key by mistake during the programming a high pitched beep is generated Locking and unlocking the keyboard gt Press then within one second to lock or unlock the keyboard This function locks only the keyboard to prevent any false manipulation The colored buttons on the left hand side are still available When the keyboard is locked a small lock appears at the bottom right of the display Programming time out gt Programming of the Relay Unit terminates automatically if no entries are made on the keyboard for more than one minute F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit Programming en 19 4
20. ottom LINE socket Flash Data GND Not used Not used Not used Not used Flash Data IN OUT Power socket unit bottom 1 Not used 2 AC 1 10 12VAC 3 AC 2 4 GND RS 485 socket unit rear RS 485 socket Relay output a RS485 A Termination RS485 A RS485 A when jumper end line is placed RS485 B Relay Output b 123456 F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Robert Bosch Healthcare Systems Inc 2400 Geng Road Suite 200 Palo Alto CA 94303 U S A www bosch telehealth com Robert Bosch Healthcare Systems 2012
21. perations when the Relay Unit is powered and its casing is removed it may not be left unattended CAUTION The Relay Unit may only be connected to the electrical sources as described in Section A 1 Electrical specifications page 28 User Manual F 01U 278 516 V1 0 2012 11 6 en Safety instructions Relay Unit 1 4 1 GPP D SG So CAUTION Maintenance and repairs may only be performed in conformance with the instructions and by authorized technical personnel only The sole possession of the user manual does not allow the personnel to perform any kind of repair on the Relay Unit Take into account all the warnings and follow all the instructions displayed on the Relay Unit and those which are printed in the documentation Never try to use replacement pieces other than those authorized by the manufacturer of the Relay Unit CAUTION It is mandatory to use the products specified in the present user manual to clean the Relay Unit If you plan to use another product only do so after having obtained the authorization of the manufacturer DANGER The Relay Unit contains highly sensitive electronic components It should be opened only in an ESD protected environment with respect to the following precautions 1 Discharge yourself from electrostatic loads by touching a grounded conductive surface before opening the unit 2 Avoid touching conductive parts inside the unit if not absolutely necessary CAUTION Never let any
22. s the recycling of materials For more information on available collection facilities contact your local waste collection service or your local representative Disassembly Only authorized personnel are allowed to disassemble a Relay Unit Returning to the manufacturer If there is no practical disposal place the Relay Unit may be returned to your local representative Materials The Relay Unit must be returned to an authorized point of recycling In order to protect people and environment the Relay Unit must be recycled in an adequate manner Consequently all applicable laws and bylaws must be respected Battery NOTICE The battery should be disposed of as household waste Use a battery disposal facility when available gt Please check local regulations for disposal of batteries or call your local representative for information User Manual F 01U 278 516 V1 0 2012 11 28 en A 1 A 2 A 3 Relay Unit Appendix Electrical specifications Voltage 115 10VAC Feary em Dimensions and weight Depth von Casing weight Weisht including antenna and power supply adaptor 26 1 740 Environmental conditions Operating temperature 32 104 F 0 40 C F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit len 29 A A List of criteria Criterion Number Alarm A or Event Commet OO ERROR Io System malfunction e g component defective PERSONNEL A Coded key a
23. t labeled 10V AC 1 under the unit For connector wiring see Section A 5 2 Power socket unit bottom page 30 Bosch Security Systems User Manual F 01U 278 516 V1 0 2012 11 16 en Installation Relay Unit 3 2 6 Connecting the RS 485 One Main Unit and up to 32 Relay Units can be connected to an RS 485 bus Please contact a specialist for a correct installation gt See Section A 5 3 RS 485 socket unit rear page 30 for connector wiring CAUTION Do not use a star connection for the RS 485 network Incorrect connection Main Unit Relay Unit 2 Relay Unit n Correct connection RS 485 bus 1 twisted pair cable 100 Q 1000 AT TOT d CH AI CID AI UC AY CID NOTICE The Main or Relay Units located at the two ends of the bus must be terminated with a 100 Ohm resistor F 01U 278 516 V1 0 2012 11 User Manual Bosch Security Systems Relay Unit 3 2 7 Bosch Security Systems Installation en 17 Setting the 100 Ohm termination jumper Within the Main or Relay Units the RS 485 interface can be configured with a jumper 1 Disassemble the unit as described in Section 6 5 1 Disassembling the unit page 25 2 Remove the communication board as described in Section Removing the communication board page 25 3 Put the 100 Ohm termination jumper J112 1 4 Assemble the communication board and the unit This is basically the reverse of the disassembling pr
24. tance of safety instructions Each safety and protection instruction in this manual must be adhered to in order to avoid personnel injuries property damages or environmental pollution In a similar manner the legal bylaws the measures in prevention of accidents and for the protection of the environment as well as the recognized technical rules aiming at appropriate and safe working conditions which as applied in the country and at the place of use of the Relay Unit must be adhered to Disregarding safety rules Disregarding the safety rules as well as existing legal and technical regulations may lead to accidents to property damages or to environmental pollution Environmental conditions NOTICE The Relay Unit must not be located near a water tap or any other source of water The electrical safety of the unit is only guaranteed if the electrical installation is conform to the national regulation and if this installation works properly The Relay Unit may not be used in buildings prone to fire and explosion hazards NOTICE The Relay Unit may not be used under exposure to the direct sunlight to heat to dust orto an excessive humidity only use the equipment in a clean environment gt Install the Relay Unit in a dry place away from any source of heat CAUTION Interferences Avoid immediate proximity to other electric devices such as a television General safety instructions DANGER Electrocution During maintenance o
Download Pdf Manuals
Related Search