BOB AA000001 User's Manual
Contents
1. and safe operation If you are unclear on any point contact your dealer or BOB before use OMA09D P1 ATTACH MAIN BAR i SET PARKING BRAKE See the Parking Brake section of your stroller owner s manual y POSITION ARMS ASSEMBLE SCREW PLUG AND BAR Rotate arms into an Insert one pivot screw through one end of main bar Upright position J and into pivot plug Pivot Plug POSITION ICSA INSERT PIVOT PLUG AND SCREW Holding pivot screw and pivot plug in place with hand position ends of main ae bar over pivot brackets 3 ik te a oe bracket and push r pivot screw flush against bar Pal INSERT PIVOT PLUG S INSERT PIVOT SCREW ON OPPOSITE SIDE Slip pivot plug tO Insert pivot screw under end of through main bar main bar and pivot plug and into Into opening on opening on pivot pivot bracket bracket 9 INSTALL PIVOT NUT I REPEAT STEPS 8 AND 9 FOR OTHER SIDE Use a Phillips screwdriver to tighten Reach under fabric seat pivot screw clockwise Thread pivot nut onto while holding pivot nut pivot screw as shown OMA09D ATTACH RESTRAINT BELT M F AND ARMS I LOCATE FABRIC SCREWS Extend canopy to expose lower fabric screw 1 REMOVE FABRIC SCREW Remove screw with Phillips screwdriver exposing fabric grommet and rivet nut Repeat on other side Slide restraint belt M grommet between end of arm and fabric grommet Align arm hole over fabric grommet and riv2. Children s Products Inc Peg P rego Primo Viaggio and Primo Viaggio SIP are registered and proprietary trademarks of Peg P rego S P A Corporation BOB Trailers Inc takes pride in its workmanship and strives to manufacture the best products possible Therefore we warranty the ICSA against defects in material and workmanship subject to the conditions listed below Since no product is indestructible it does not cover defects attributable to or resulting from normal wear abuse or alteration The ICSA is warranted for one year from the date of original purchase Warranty is only valid for the original purchaser Proof of purchase is required to exercise this warranty Labor and freight charges are not included Normal wear neglect abuse accidents and improper use are not covered by this warranty OMAO09D Warranty claims must be made through an authorized dealer This warranty is limited to the repair or replacement of the defective part BOB Trailers Inc shall in no event be respon sible for consequential or special damages This Limited Warranty is the only express or implied warranty applicable to BOB Trailers Inc Any implied warranties including warranties of merchantability and fitness shall be limited in scope and duration in accordance with this limited warranty P12
3. Infant Car Seat Congratulations on your purchase of the BOB Infant Car Seat Adapter ICSA It is designed to allow the attachment of an Infant Car Seat to your BOB Stroller Please refer to the tables at right for details of compatible strollers and car seats Tray D Long Screw installed Pivot Nut 2x AA Pivot Screw 2x D D Pivot Plug 2x r Sharp Screw 2x Adapter Instructions BOB Stroller Model Year Compatibility Model Year s Model Serial Number 2005andnewer Sport Utility Stroller AA000001 and higher 2005andnewer Ironman AC000001 and higher 2005andnewer Revolution AF000001 and higher 2005andnewer Stroller Strides AG000001 and higher 2007 andnewer Revolution 12 AK000001 and higher Brand Model Britax Companion Snug Ride SafeSeat Primo Viaggio Primo Viaggio SIP Year s 2003 and newer 2003 and newer 2006 and newer 2003 and newer 2006 and newer Graco Graco Peg P rego Peg P rego Long Screw LE installed Arm Short Screw installed S f Arm Accessory Bar Short Screw installed Main Bar Restraint Belt F Restraint Belt M TOOLS NEEDED Phillips screwdriver TAKE TIME READ AND UNDERSTAND INSTRUCTIONS COMPLETELY Before attempting to assemble or use your new ICSA read and understand these assembly instructions completely as well as the warnings at the end of this document to insure proper assembly
4. LE 29 26 CAR SEAT Place car seat rear facing onto ICSA accessory bar in a straight downward motion Lower seat back 7 to 8 See Reclining Seat section of your stroller owner s manual Move car seat handle into upright carrying position k ENGAGE CARSEAT 4 FASTEN RESTRAINT BELT Slide grooves on underside of car seat Fasten restraint belt over top onto ICSA accessory bar of infant car seat as shown Pull on red ring to tighten A Warning Be sure restraint belt tension is not constricting child as it may cause serious injury 31 DOUBLE CHECK CAR SEAT IS SECURELY ATTACHED Pull car seat upward without A Wa rning TO REMOVE Britax removing restraint belt You should not be able to Failure to securely attach Go To 47 remove car seat without car seat may result in unfastening restraint belt serious injury or death OMAO9D P5 Peg P rego KYA RAISE SEAT BACK KKJ POSITION HANDLE KZ POSITION CAR SEAT See the Reclining Seat section of your stroller Move car seat handle p l owner s manual into upright carrying lace car sea position i rear facing onto ICSA accessory bar in a straight downward Fasten restraint belt over top of infant car Slide grooves on seat as shown underside of car seat onto ICSA accessory bar K DOUBLE CHECK CAR SEAT IS SECURELY ATTACHED Pull car seat upward without removing restraint belt You s
5. bility to the stroller seat Therefore prior to placing child directly in stroller seat the ICSA Restraint Belt and Accessory Bar must be removed from the stroller AND the Tray must be installed Failure to do so may result in serious injury or death Read and understand all owner s manuals and warnings for all BOB products used with the ICSA before use Read and understand infant car seat owner s manual before use Always use seat harness of Infant Car Seat to avoid children falling out of stroller Refer to your Infant Car Seat owner s manual for maximum capacity limitations and other safety warnings Infant Car Seat Adapter Warnings Follow assembly instructions Failure to properly install this accessory product may result in accidents severe injury or death If you are not sure you can properly install this accessory contact your BOB retailer and arrange for them to perform the installation Never leave children unattended in the stroller infant car seat Always secure the infant car seat with the restraint belt when the car seat is placed in the stroller Failure to do so may result in serious injury or death Always keep your Infant Car Seat handle in the vertical and locked position while in stroller as extra protection for your child Stroller may become unstable if parcel bags are incorrectly attached or if bags other than those recommended by BOB Trailers Inc are used Do not run or jog
6. death TO REMOVE Graco Go To 3 TO REMOVE CAR SEAT G SET PARKING BRAKE 4 UNFASTEN RESTRAINT BELT See the Parking Brake section of your stroller owner s manual Unfasten restraint belt Place ends outside seat REMOVE CAR SEAT C FASTEN RESTRAINT BELT Fasten restraint belt Britax when not in use Peg P rego With car seat handle in upright position lift car seat straight up and off ICSA bar Graco With car seat handle in upright position squeeze red release button under Graco car seat canopy lift car seat straight up and off ICSA bar OMAO9D Pg TRAY INSTALLATION REMOVE ACCESSORY BAR rt Warning be Children should not be d Using a Phillips screwdriver placed directly in the remove both screws BOB Stroller seat with Ko the ICSA installed unless tray is installed for safety and protection TIP Attach short screws to accessory bar for future use CAUTION Ends of accessory bar are sharp REMOVE SCREWS Hook tray onto main bar Using a Phillips screwdriver remove long screws from tray 54 ROTATE TRAY Rotate tray towards stroller seat until it rests on main bar Insert long screw through each hole in tray main bar and into nut on underside of tray Tighten firmly with Phillips screwdriver Line up holes a eop OMA09D REMOVE RESTRAINT BELT M Using a Phillips screwdriver remove sha
7. et nut Red pull ring should face out Hold strap at a 90 degree angle Insert sharp screw through end of arm restraint belt grommet fabric grommet and into rivet nut Tighten firmly with Phillips screwdriver Note If screw does not turn easily unscrew and start again P3 OMA09D ATTACH RESTRAINT BELT F IV BUCKLE BELT J POSITION ARM to restraint belt M and frame IVD POSITION RESTRAINT BELT F Slide restraint belt F grommet between end of w arm and fabric grommet Align arm hole over fabric grommet and rivet nut YI INSERT SHARP SCREW Insert sharp screw through end of arm restraint belt grommet fabric grommet and into rivet nut Tighten firmly with Phillips screwdriver Note If screw does not turn easily unscrew and start again UNBUCKLE RESTRAINT BELT See the Parking Brake Position canopy section of your stroller Unbuckle restraint belt against handle bar owner s manual Place ends outside seat OMAO09D INSTALL INFANT CAR SEAT When installing car seat in the ICSA for the first time test fit with the car seat unoccupied to ensure you understand the process A Wa rn i n C Installing occupied Infant Car Seat on ICSA for first time may result in accident serious injury or death Graco Go To amp Britax Go To 25 Peg P rego Go To 32 Britax yy POSITION LOWER SEAT BACK RAISE HAND
8. hould not be able to TO REMOVE remove car seat without Peg P rego unfastening restraint belt Go To 47 A Warning Failure to securely attach car seat may A Warning result in serious injury Be sure restraint belt tension is not or death constricting child as it may cause serious injury OMAO9D P6 Graco RAISE SEAT BACK REMOVE ACCESSORY BAR See the Reclining Seat section of your stroller owner s manual VS Using a Phillips screwdriver remove both screws TIP Attach short screws to accessory bar for future use CAUTION Ends of accessory bar are sharp POSITION HANDLE 3 POSITION CAR SEAT Move car seat handle into upright carrying position Place car seat rear facing onto ICSA main bar in a straight downward motion a ENGAGE CAR SEAT 7 rasten RESTRAINT BELT Slide grooves on underside of Fasten restraint belt over top of car seat onto ICSA main bar infant car seat as shown lt a Red hook on Graco K OAA eini VD 4 OMAO9D P7 TIGHTEN RESTRAINT BELT DOUBLE CHECK CAR SEAT Bellona IS SECURELY ATTACHED Pull car seat upward without removing restraint belt You should not be able to remove car seat without unfastening restraint belt A Warning Be sure restraint belt tension is not constricting child as it may cause serious injury A Warning Failure to securely attach car seat may result in serious injury or
9. rp screw and restraint belt M Insert sharp screw through end of arm fabric grommet and into rivet nut REMOVE SHARP SCREW AND BELT Using a Phillips screwdriver remove sharp screw and restraint belt F Insert sharp screw through end of arm fabric grommet and into rivet nut OMAO09D C TIGHTEN SHARP SCREW Position arm between canopy and frame Align arm hole over fabric grommet and rivet nut Tighten firmly with Phillips screwdriver Note If screw does not turn easily unscrew and start again 1 POSITION ARM Position arm between canopy and frame Align arm hole over fabric grommet and rivet nut E Tighten firmly with Phillips screwdriver Note If screw does not turn easily unscrew and start again P10 e The BOB Infant Car Seat Adapter is designed for use with single seat BOB Strollers and compatible Infant Car Seats This product is not a universal adapter Do not use with car seats and stroller models other than those specifically listed in the Stroller and Car Seat Compatibility charts listed on page 1 Children should not be placed directly in the BOB Stroller seat with the ICSA installed unless tray is installed directly in front of child for safety and protection The ICSA Restraint Belt can interfere with proper function of the safety harness system Additionally the ICSA Accessory Bar can interfere with accessi
10. when using the ICSA with car seat installed Doing so may result in serious injury or death Do not use off road or on uneven terrain when using the ICSA with car seat installed Doing so may cause stroller to become unstable and result in accident serious injury or death Children develop at different rates Consult with your pediatrician regarding the suit ability of the stroller use with your child BOB IS NOT RESPONSIBLE FOR INJURY DAMAGE OR FAILURE THAT RESULTS FROM OWNERS FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING OMA09D P11 BOB is a company that produces high quality products designed to promote a healthy outdoor life style Go to www bobgear com for our complete line of products Before attempting to assemble or use your new ICSA read and understand these instructions completely to insure proper assembly and operation If you are unclear on any point contact your dealer place of purchase or BOB toll free 1 800 893 2447 before use A list of dealers is listed on our website www bobgear com For updates to this manual our warranty and for other recent product notifications please visit www bobgear com periodically LIMITED WARRANTY B O B B O B Logo and BOB are proprietary trademarks of BOB Trailers Inc Britax and Companion are registered trademarks of Britax Excelsior Ltd and related companies Graco Snug Ride and SafeSeat are registered and proprietary trademarks of Graco
Download Pdf Manuals
Related Search