Black Box T1/E1 User's Manual
Contents
1. UTP DCE DTE setting The UTP DCE DTE switch is used to eliminate the need for crossover and custom cables to connect devices together when using the RJ 45 48 port Set this switch to DCE to use a straight through cable and to DTE when a crossover cable would be required Twisted 1 RTP TIP Twisted 1 RTIP TIP Pair 1 2 RRING TRING Pair 1 2 RRING TRING Twisted 4 TTIP RTIP Twisted 4 TTIP RTIP Pair 2 5 TRING RRING Pair 2 5 TRING RRING T1 E1 Copper line configuration settings The T1 E1 copper line codes and line lengths are configured using dip switches located on the side of the FlexPoint T1 E1 media converter Page 4 NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante 72. 1 When Using in a stand alone configuration this product is intended to be and must be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp 2 This product should always be used only with the supplied power unit 3 Models shipped with international power supplies are capable of auto switching from 100 230V and are supplied with a U S type NEMA 5 15 power cable 4 For products being shipped outside of the U S the user is required to install a properly grounded IEC Page 2 Operational rating on relay pins 3 amp 6 0 220VDC max 2A LED Indicators LED Color Status Description Power Yellow On Power applied Fiber Green Off No signal detect On Signal detect Blink All ones received UTP Coax Green Off No signal detect On Signal detect Blink All ones received Test Yellow Off Normal operation On L LB or All 1 s Test mode Blink R L LB Received master Fast Blink R L LB Received slave Fiber Cable Specifications Multimode Cable 50 125 62 5 125 100 140 um Wavelength 1300nm Max Distance 5km 3 1mi Single mode Cable 9 125 um Wavelength 1300nm Max Distance 28km 16 8mi Single mode long haul Cable 9 125 um Page 8 320 appliance cable with a minimum rating of 10 AMPs 5 User supplied cables must meet the required safety agency approvals applicable international standards and electrical ratings for the region WARNING Before inserting the Power Ad
3. 6 El aparato el ctrico debe ser usado nicamente con carritos 0 pedelstales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico mas all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sofa alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Page 11 Local loop back L LB This switch will set the FlexPoint T1 E1 converter in a loop back mode on both the fiber and copper connections By returning the switch to the normal position the unit will resume to normal operation Cu Rx FO Tx gt gt gt gt lt 4 lt Cu Tx FO Rx Loopback Enabled Remot
4. Impedance Impedance characteristic Maximum distance 6 000 ft 22 to 24 AWG 120 Q 10 2 6 dB 100m 1 0 MHz 8 000 ft 22 to 24 AWG 75 2 10 2 dB 100m 1 0 MHz 8 000 ft 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 e Fax 724 746 0746 Page 9 Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Coax E1 Connector Attach the BNC to the FlexPoint T1 E1 converter and attach the other end of the BNC to the network equipment Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Switch Settings UTP DCE DTE setting The UTP DCE DTE switch is used to eliminate the need for crossover and custom cables to connect devices together when using the RJ 45 48 port Set this switch to DCE to use a straight through cable and to DTE when a crossover cable would be required Twisted 1 RTP TIP Twisted 1 RTIP TIP Pair 1 2 RRING TRING Pair 1 2 RRING TRING Twisted 4 TTIP RTIP Twisted 4 TTIP RTP Pair 2 5 TRING RRING Pair 2 5 TRING RRING T1 E1 Copper line configuration settings The T1 E1 copper line codes and line lengths are configured using dip switches located on the side of the FlexPoint T1 E1 media converter Page 4 TRADEMARKS All applied for and registered trademarks are the property
5. On Signal detect Blink All ones received UTP Coax Green Off No signal detect On Signal detect Blink All ones received Test Yellow Off Normal operation On L LB or All 1 s Test mode Blink R L LB Received master Fast Blink R L LB Received slave Fiber Cable Specifications Multimode Cable 50 125 62 5 125 100 140 um Wavelength 1300nm Max Distance 5km 3 1mi Single mode Cable 9 125 um Wavelength 1300nm Max Distance 28km 16 8mi Single mode long haul Cable 9 125 um Page 8 Description The FlexPoint T1 E1 connects T1 and E1 devices such as PBXs CSUs and routers via multimode MM or single mode SM fiber Designed to extend the standard T1 E1 twisted pair or Coax network distances over fiber this converter provides protection from environmental noise and effectively increases high speed network reliability The following models are described here Model Fiber Type Max Distance MT660A MM MM ST 1300nm 5km 3 1mi MT661A SM SM ST 1300nm 28km 16 8mi MT662A MSC MM SC 1300nm 5km 3 1mi MT663A SSC SM SC 1300nm 28km 16 8mi MT664A SSC SM SC 1300nm 58km 36 mi MT660A MM E MM ST 1300nm 5km 3 1mi MT661A SM E SM ST 1300nm 28km 16 8mi MT662AE MSC MM SC 1300nm 5km 3 1mi MT663AE SSC_ SM SC 1300nm 28km 16 8mi MT664AE SSC_ SM SC 1300nm 58km 36 mi Power Adapter Notice 1 When Using in a stand alone configuration this product is intended to be and must be used only with a Listed
6. BAA Operational switch settings and functions The following operational switches located on the front of the FlexPoint T1 E1 converter are to assist in installation and fault isolation ME lt Local Dual Loop Back Remote amp Local Loop Back Force 1 s to Fiber Wud lt Force 1 s Copper Norm Normal gt Norm Page 5 2 Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 3 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y receptaculos donde salen del aparato 4 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 5 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 6 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 7 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 8 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido dafiado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E
7. Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada Page 10 Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Coax E1 Connector Attach the BNC to the FlexPoint T1 E1 converter and attach the other end of the BNC to the network equipment Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Switch Settings
8. Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp 2 This product should always be used only with the supplied power unit 3 Models shipped with international power supplies are capable of auto switching from 100 230V and are supplied with a U S type NEMA 5 15 power cable 4 For products being shipped outside of the U S the user is required to install a properly grounded IEC Page 2 Wavelength Max Distance 1300nm 58km 36mi Copper Cable Specifications Twisted Pair cable for T1 Gauge Impedance Impedance characteristic Maximum distance Twisted Pair cable for E1 Gauge Impedance Impedance characteristic Maximum distance Coax cable for E1 Gauge Impedance Impedance characteristic Maximum distance 22 to 24 AWG 100 2 10 2 6 dB 100m 1 0 MHz 6 000 ft 22 to 24 AWG 1202 10 2 6 dB 100m 1 0 MHz 8 000 ft 22 to 24 AWG 759 10 2 dB 100m 1 0 MHz 8 000 ft 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 e Fax 724 746 0746 Page 9 320 appliance cable with a minimum rating of 10 AMPs 5 User supplied cables must meet the required safety agency approvals applicable international standards and electrical ratings for the region WARNING Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source Mounting instructions The FlexPoint Fiber Converter can be solo mounted using a wal
9. El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sofa alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Page 11 Line Type Port Type Distances Switch Positions i 2 3 4 T1 DSX 1 RJ 45 48 0 133 BBBB T1 DSX 1 RJ 45 48 133 265 BBBA T1DSX 1 RJ 45 48 266 39 BBAB T1 DSX 1 RJ 45 48 399 53 BBAA T1 DSX 1 RJ 45 48 533 655 BABB T1 DS 1 RJ 45 48 0dB BBBB T1 DS 1 RJ 45 48 7 5 dB BABA T1 DS 1 RJ 45 48 15 0 dB BAAB T1 DS 1 RJ 45 48 22 5 dB BAAA E1759 Coax BNC Standard A B B B E1120Q RJ 45 48 Standarda ABBA E175Q Coax BNC Extended A BAB E1120Q RJ 45 48 Extended A
10. El aparto ha sido tirado o su cubierta ha sido da ada 040 01021 001E 3 06 Page 12 Local loop back L LB This switch will set the FlexPoint T1 E1 converter in a loop back mode on both the fiber and copper connections By returning the switch to the normal position the unit will resume to normal operation CuRx FO Tx gt gt gt gt gt lt lt lt lt Cu Tx FO Rx Loopback Enabled Remote loop back R L LB This switch will allow the entire fiber segment to be tested at either of the FlexPoint T1 E1 converters without having to set switches on both units When set in this mode of operation the local unit is switched in a local loop back mode And in addition to the local loop back mode of operation the fiber Tx port will be further encoded to carry a remote loop back protocol This remote loop back protocol will set the far end FlexPoint T1 E1 converter to remote loop back mode of operation and return a signal to the sending unit An LED on the local and remote FlexPoint T1 E1 converters will show a confirmation that the fiber segment is communicating properly between devices By returning the switch to the normal position it will resume to normal operation CuR FOT FORx Cots gt gt a lt Cole FOR FOI Cok Remote Loop Request Over Fiber Page 6
11. de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n Servicio por personal calificado debera ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada u D x oo 040 01021 001E 3 06 Page 12 Local loop back and Remote loop back When both Local and Remote Loop back are set to the Normal position the FlexPoint T1 E1 uses the default B8ZS data format When both switches are turned to their On position it uses the AMI data format Transmit force 1 s to fiber This switch is used to insert an all ones pattern into the data stream being transmitted out of the fiber port on the FlexPoint T1 E1 converter Data being received on the coax or twisted pair will be disabled and data being received on the fiber is passed through to the coax or twisted pair side By returning the switch to the normal position the unit will resume to normal operation Transmit force 1 s to Coax or UTP This switch is used to insert an all ones pattern
12. minist re des Communications du Canada Page 10 Line Type PortType Distances Switch Positions 1 2 3 4 T1 DSX 1 RJ 45 48 0 133 BBBB T1 DSX 1 RJ 45 48 133 266 BBBA T1 DSX 1 RJ 45 48 266 39 BBA B T1 DSX 1 RJ 45 48 399 5379 BBAA T1 DSX 1 RJ 45 48 533 655 BABB T1 DS 1 RJ 45 48 O0dB BBBB T1 DS 1 RJ 45 48 7 5 dB BABA T1 DS 1 RJ 45 48 15 0 dB BAAB T1 DS 1 RJ 45 48 22 5 dB BAAA E1759 Coax BNC Standard A B B B E1120Q RJ 45 48 Stanad ABBA E175Q Coax BNC Extended A BAB E1120Q RJ 45 48 Extended A BAA Operational switch settings and functions The following operational switches located on the front of the FlexPoint T1 E1 converter are to assist in installation and fault isolation Local Dual Loop Back Remote amp Local Loop Back Force 1 s to Fiber Wud lt Force 1 s Copper Norm Normal gt Norm Page 5 NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deberan ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc
13. of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le
14. The World s Source for Cabling and Network Connectivity S Black Box Corporation E US Power Supply International Power Supply MT660A MM MT660A MM E MT661A SM MT661A SM E MT662A MSC MT662AE MSC MT663A SSC MT663AE SSC MT664A SSC MT664AE SSC FlexPoint T1 E1 Copper to Fiber Line Driver CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT ulside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com Page 1 Local loop back and Remote loop back When both Local and Remote Loop back are set to the Normal position the FlexPoint T1 E1 uses the default B8ZS data format When both switches are turned to their On position it uses the AMI data format Transmit force 1 s to fiber This switch is used to insert an all ones pattern into the data stream being transmitted out of the fiber port on the FlexPoint T1 E1 converter Data being received on the coax or twisted pair will be disabled and data being received on the fiber is passed through to the coax or twisted pair side By returning the switch to the normal position the unit will resume to normal operation Transmit force 1 s to Coax or UTP This switch is used to insert an all ones pattern into the data stream being transmitted out of the coax
15. apter verify that the power on the unit is appropriate for your AC line voltage source Mounting instructions The FlexPoint Fiber Converter can be solo mounted using a wall mounting kit or rack mounted using a 5 unit shelf or a high density FlexPoint 14 Unit Power Redundant Chassis Fiber Optic Cable Attachment Connect the fiber cables between the FlexPoint T1 E1 converters The transmit Tx must attach to the receive side and the receive Rx must attach to the transmit side Note Use fiber cables that are compliant with the specifications that are outlined in fiber cable specifications Copper Cable Attachment RJ 45 RJ 48 T1 E1 connector Connect to the RJ 45 48 connector on the FlexPoint T1 E1 converter via a category 3 or better cable Category 5 is recomended and attach the other end to the network equipment The twisted pair connection requires two active pairs in a T1 E1 environment The active pairs are pins 1 amp 2 and pins 4 amp 5 Only dedicated wire pairs should be used for the active pins Set the UTP DCE DTE switch for the RJ 45 48 port to the appropriate setting Page 3 Wavelength 1300nm Max Distance 58km 36mi Copper Cable Specifications Twisted Pair cable for T1 Gauge 22 to 24 AWG Impedance 100 2 10 Impedance characteristic 2 6 dB 100m 1 0 MHz Maximum distance Twisted Pair cable for E1 Gauge Impedance Impedance characteristic Maximum distance Coax cable for E1 Gauge
16. e loop back R L LB This switch will allow the entire fiber segment to be tested at either of the FlexPoint T1 E1 converters without having to set switches on both units When set in this mode of operation the local unit is switched in a local loop back mode And in addition to the local loop back mode of operation the fiber Tx port will be further encoded to carry a remote loop back protocol This remote loop back protocol will set the far end FlexPoint T1 E1 converter to remote loop back mode of operation and return a signal to the sending unit An LED on the local and remote FlexPoint T1 E1 converters will show a confirmation that the fiber segment is communicating properly between devices By returning the switch to the normal position it will resume to normal operation CuRx FOTx FORK Culx gt gt gt g CuTx FORK FOTx CuRe Remote Loop Request Over Fiber Page 6 N Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 4 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 5 En caso de existir una antena externa deber ser localizada lejos
17. into the data stream being transmitted out of the coax or twisted pair on the FlexPoint T1 E1 converter Data being received on the fiber will be disabled and data being received on the coax or twisted pair is passed through to the fiber side By returning the switch to the normal position the unit will resume to normal operation Alarm Relay Contacts The FlexPoint T1 E1 converter also features dry relay contacts for optionally connecting the media converter into a separate T1 E1 alarm circuit The relay closes when a loss of power or when signal detect is lost to the copper or fiber connection Relay RJ 45 RJ 48 Page 7 S Black Box Corporation The World s Source for Cabling and Network Connectivity MT660A MM MT660A MM E MT661A SM MT661A SM E MT662A MSC MT662AE MSC MT663A SSC MT663AE SSC MT664A SSC MT664AE SSC FlexPoint T1 E1 Copper to Fiber Line Driver CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT outside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com Page 1 Operational rating on relay pins 3 amp 6 0 220VDC max 2A LED Indicators LED Color Status Description Power Yellow On Power applied Fiber Green Off No signal detect
18. l mounting kit or rack mounted using a 5 unit shelf or a high density FlexPoint 14 Unit Power Redundant Chassis Fiber Optic Cable Attachment Connect the fiber cables between the FlexPoint T1 E1 converters The transmit Tx must attach to the receive side and the receive Rx must attach to the transmit side Note Use fiber cables that are compliant with the specifications that are outlined in fiber cable specifications Copper Cable Attachment RJ 45 RJ 48 T1 E1 connector Connect to the RJ 45 48 connector on the FlexPoint T1 E1 converter via a category 3 or better cable Category 5 is recomended and attach the other end to the network equipment The twisted pair connection requires two active pairs in a T1 E1 environment The active pairs are pins 1 amp 2 and pins 4 amp 5 Only dedicated wire pairs should be used for the active pins Set the UTP DCE DTE switch for the RJ 45 48 port to the appropriate setting Page 3 TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a
19. or twisted pair on the FlexPoint T1 E1 converter Data being received on the fiber will be disabled and data being received on the coax or twisted pair is passed through to the fiber side By returning the switch to the normal position the unit will resume to normal operation Alarm Relay Contacts The FlexPoint T1 E1 converter also features dry relay contacts for optionally connecting the media converter into a separate T1 E1 alarm circuit The relay closes when a loss of power or when signal detect is lost to the copper or fiber connection Relay RJ 45 RJ 48 Page 7 Description The FlexPoint T1 E1 connects T1 and E1 devices such as PBXs CSUs and routers via multimode MM or single mode SM fiber Designed to extend the standard T1 E1 twisted pair or Coax network distances over fiber this converter provides protection from environmental noise and effectively increases high speed network reliability The following models are described here Model Fiber Type Max Distance MT660A MM MM ST 1300nm 5km 3 1mi MT661A SM SM ST 1300nm 28km 16 8mi MT662A MSC MM SC 1300nm 5km 3 1mi MT663A SSC SM SC 1300nm 28km 16 8mi MT664A SSC SM SC 1300nm 58km 36 mi MT660A MM E MM ST 1300nm 5km 3 1mi MT661A SM E SM ST 1300nm 28km 16 8mi MT662AE MSC MM SC 1300nm 5km 3 1mi MT663AE SSC_ SM SC 1300nm 28km 16 8mi MT664AE SSC SM SC 1300nm 58km 36 mi Power Adapter Notice
Download Pdf Manuals
Related Search