Bissell 2X User's Manual
Contents
1. ProHeat 2X after Healthy Home USER S GUIDE 6604 AND 73A5 SERIES 3 Safety Instructions 4 5 Product View 6 Assembly 7 9 Special Features 9 17 Operation 17 19 Maintenance and Care 19 21 Troubleshooting 21 Consumer Services 22 23 Replacement Parts 24 Warranty os ZA H Dual DIRTLFTER powerbrushesi ME EA CLEANING nowsd i 2 Thanks for buying a BISSELL ProHeat 2X Healthy Home We re glad you purchased a BISSELL ProHeat 2X heated formula deep cleaner Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your ProHeat 2X is well made and we back it with a limited one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your ProHeat 2X Thanks again from all of us at BISSELL Am aA 1 Rr Mark J Bissell President and Chief Executive Officer www bissell ca 1 800 263 2535 www bissell ca IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following Read all instructions before using your ProHeat 2X A WARN l NG To reduce the risk of fire electric s2. Clean the hose by suctioning clean water from the tap Before replacing lift end of hose and stretch out to ensure all water is cleared from hose Refer to page 14 illustrations 9 amp 10 8 After carpet is dry vacuum again to remove hair and fuzz Small belt removal and replacement Occasional replacement of one or both belts may become necessary If that is needed please follow the instructions below 1 Turn off the machine and unplug it from the outlet 2 Remove both the 2 in 1 water tank and the formula tank Set aside 3 Unscrew the front nozzle and remove it Set aside 4 Turn the machine on its side 6 IMPORTANT cord side down 5 Remove the clear end cap by unscrewing the 2 black screws Take care not to drop the screws into the unit Remove 1 silver screw from the pivot arm Remove pivot arm by gently lifting up 6 7 8 Remove small brush belt 9 Replace small brush belt and reverse steps above A oo www bissell ca aissel 1 800 263 2535 Maintenance and care Brushes can be removed for cleaning or replacement as needed 1 Follow small belt removal Instructions on page 18 2 Remove brush rolls by pulling them off of the metal rods 3 Place cleaned or new brush rolls back onto the rods Make sure one washer is on each end of the rollers prior to sliding onto the rod Be sure to let the rod slide through the bushing to insure proper fit 4 Re attach the
3. 5 Pretreating optional Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways Option A BISSELL Tough Stain PreTreat A Spray the BISSELL Tough Stain Pre treat formula onto heavy traffic areas soiled areas or stains B Allow to penetrate for at least 3 minutes C Clean as normal using the BISSELL ProHeat 2X machine on the high traffic setting following the instructions below Option B CleanShot A Set Custom Clean for the desired setting B Press the CleanShot button and aim the focused stream onto the stain Allow the formula to soak in for 30 seconds C Run the machine over the stain to extract Repeat as needed until the stain is gone D Rinse if desired Carpet cleaning 1 Fill the 2 in 1 Water Tank Remove the tank from the base of the machine by lifting up the tank carry handle Carry like a bucket to the sink 1a Unlatch the top of the tank from the bottom by lifting up on the tank latch which is located on the back of the tank 1b Remove the top of the tank by lifting up on the handle Note how the lip on the top tank separates from the groove in the bottom tank This placement is important when putting the tank back together 1c Fill the heavy duty bladder with clean hot tap water Do not boil or microwave water as it can destroy the bladder 1d Leaving the filled bottom of the tank on a flat surface onl
4. Part Name 1 203 6611 Grey Tank Assembly complete 2 203 6660 Grey Tank Lid 3 203 6618 Grey Tank Bottom 4 203 6675 Cap and Insert for Water Tank 5 203 6676 Formula Tank includes Cap amp Insert for Formula Tank 6 203 6677 Cap and Insert for Formula Tank 7 203 6678 Front Nozzle includes gasket 8 203 6679 Autoload Gasket fits both Water and Formula Tank 9 203 6845 Float Door 10 203 6680 Tank Filter Lint Screen 11 203 6681 Water Tank Latch 12 203 6682 Cord Wrap Black Blue or Purple cord wrap available upon request 13 203 6685 Clear End Cap w Edge Brushes 2 pack includes screws 14 203 6686 Brush Roll 6 row includes 1 brush axle 2 swivel arms 15 203 6688 Small Brush Belt non cord side 16 203 6804 Large Brush Belt cord side 17 203 6689 Hose Secure Latch 18 203 6690 Hose Rack Assembly Top Bottom Hose Rack Screws 19 203 6994 CleanShot Cover Not all parts are included with every model 1 2 3 4 5 6 PES i Bissell 22 www bissell ca a 1 800 263 2535 Accessories Replacement Parts Below please find a list of common replacement parts While not all of these parts may have come with your specific machine all are available to you for purchase if desired Item Part No Part Name 1 203 6651 3 Tough Stain Tool 2 203 6652 Powered TurboBrush Hand Tool 3 203 6653 4 Upholstery Tool 4 203 6654 6 Stair Tool 5 203 6655 Spraying Crevice Tool 6 203 5642 Bare Floor Tool with trial si
5. carpets that have never been deep cleaned before This debris should be picked up and thrown away Fill the heavy duty bladder with clean hot tap water following instructions 1c through 1e on page 10 Note Remember to secure the tank latch in the back and test to make sure it is secure before picking up the tank Always check the level of cleaning formula in the formula tank at the same time and refill as needed Water rinse Optional Rinsing is an optional step that can be done during the cleaning pro cess by switching from one of the clean settings on the Custom Clean dial to a water rinse setting or it can be done after the carpeted area has been cleaned Simply choose the water rinse setting on the custom clean dial and follow the same path as you did for cleaning taking care to do a forward wet stroke by depressing the trigger a backward wet stroke and a forward and backward dry stroke releasing the trigger Continue this until the water you see coming up the nozzle is clear A Bissell 1 800 263 2535 Operation Carpet cleaning Continued 9 CleanShot CleanShot is an optional feature that can be used to fight tough stains It can be used as either a tough stain pre treat see page 10 or can be used during the deep Cleaning process itself To use CleanShot either as a pre treat or during deep cleaning follow the instructions below A Set Custom Clean for the desired setting B Press the C
6. cause it to set and become permanent 1 www bissell ca Blot up liquids with an absorbent cloth or paper towels White materials are recommended because certain dyes may bleed and make the stain worse Gently scrape up any semi solids with a spoon or spatula Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery If the area has dried remove the remaining semi solids and residue with a sweeper or vacuum Be sure to test any spot removal formulas in an inconspicuous area first This is important as some dyes and materials could be damaged or discolored by cleaning solvents If such a change should occur try a different solution or call a professional If cleaning on Berber carpeting gently run your machine over a hidden area If no fuzzing occurs continue cleaning in soiled area CleanShot CleanShot is an optional feature that can be used to fight tough stains It can be used as either a tough stain pre treat see page 10 or can be used during the deep cleaning process itself To use CleanShot either as a pre treat or during deep cleaning follow the instructions below A Set Custom Clean for the desired setting B Press the CleanShot button and aim the focused stream onto the stain Allow the for mula to soak in for 30 seconds C Run the machine over the stain to extract Repeat as needed until the stain is gone D Rinse if desired Clean using either the FLOOR
7. long belt on the bottom to the cogs of the small roller brushes 5 Place small belt over back roller and metal cog 6 Place pivot arm in place and screw in place using the silver screw 7 Re attach clear end cap by tightening with the 2 black screws 8 Return front nozzle to front of unit by latching from underneath and then securing with a screw If you have any questions or are having trouble installing or replacing your belt s or brushes please call BISSELL Consumer Services at 1 800 263 2535 Troubleshooting Built in heater ready light does not illuminate Possible Cause 1 The heater switch is not turned ON 1 2 The power switch is not turned ON 1 Reduce Spray or No Spray Possible Cause 1 Water tank may be empty 2 Formula tank may be empty Blssel www bissell ca EN WARNING To reduce the risk of fire electric shock or injury unplug from the outlet Brush removal and large belt replacement before servicing 2 Og A S LEBEL Og Remedies 1 Turn the heater switch ON 1 2 Both switches must be ON 1 to activate the heater ready light Remedies 1 Fill heavy duty bladder with hot tap water 2 Fill formula tank with BISSELL Multi Allergen Formula for cleaning 1 800 263 2535 19 Troubleshooting Reduce Spray or No Spray continued Possible Cause 3 Tank may not be seated completely 4 Pump may have lost prime DirtLifter PowerBru
8. power cord and flex hose as shown in figure 5 7 Keep flex hose snugly in place by using the hose secure latch ProHeat 2X assembly is now complete Tough Stain Brush Crevice Tool Holder Hose Secure Latch 6 Bissell www bissell ca 1 800 263 2535 Special features Your BISSELL ProHeat 2X deep cleaner is a home cleaning system that uses the power of heat brushes and cleaning formula to get the deep down dirt for a maximum clean Not only does it come with a lot of unique features it has been designed with you the customer in mind Built in Heater feature BISSELL ProHeat 2X models all feature a patented built in heater which will heat the hot tap water you put in up to 25 F degrees 14 C hotter to safely optimize cleaning effectiveness The heater will never allow the temperature to exceed 190 F degrees 88 C The heater switch on the front of the machine controls the heater so you have the option to turn off the heat if you are cleaning delicate wool or oriental rugs Dual DirtLifter PowerBrushes The two DirtLifter PowerBrush rolls are designed to enhance cleaning performance The bristle pattern safely lifts out the deep down dirt while gently grooming carpet fibers The floating suspension self adjusts to all carpet heights Once the product is in the upright position the brushes automatically stop spinning Custom Clean The Custom Clean feature automatically
9. CLEANING or TOOLS setting on the ReadyTools dial Bissell 1 800 263 2535 15 16 Operation Hard floor cleaning Your ProHeat 2X model may have come with a hard floor attachment and Hard Floor Solutions Formula If not these products are available for purchase by contacting the BISSELL Consumer Services department by phone or at the website The hard floor tool provides effective cleaning for linoleum vinyl and tile floors Caution Do not use on unsealed hardwood floors 1 Vacuum or sweep thoroughly to pick up any loose debris and pet hair 2 Move any furniture if needed 3 Fill with water to WATER line Fill with BISSELL 2X Hard Floor Solutions to FORMULA line 4 Fill the 2 in 1 water tank with hot tap water and set aside 5 Attach the hard floor tool onto the bottom of the machine by hooking it into the nozzle and swinging it down until it clicks into place 6 Check ReadyTools dial It should be set on floor cleaning 7 Set the Custom Clean dial to normal clean 8 Plug into an outlet and turn the power switch and heater ON 1 9 Slowly move the machine forward and back over hard floor surface one time while depressing trigger Caution Do not overwet 10 Repeat the motion without pressing the trigger using the hard floor tool to squeegee and suction up the dirty water 11 Allow adequate time for floors to dry 12 Remove hard floor tool rinse and dry before storing 13 If an
10. CLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE Bissell NOTE Please keep your original sales receipt it is your warranty 2010 BISSELL Homecare Inc BISSELL Canada Corporation Niagara Falls ON L2E 6S5 All rights reserved Printed in China Part Number 120 4168 Rev 01 10 Visit our website at www bissell ca pisselr Scotchgard is a trademark of 3M www bissell ca a 1 800 263 2535
11. at out Replace before putting the top and bottom halves of the tank together 4 Before you place the cleaned 2 in 1 water tank back onto the machine simply unscrew the floor nozzle using a Phillips head 9 screwdriver This can be rinsed out at the faucet Then replace back onto the machine by starting from the bottom of the nozzle and hooking the tabs into the holes on the bottom sides of the machine Secure into place with the screw f alssel www bissell ca EEN WARNING To reduce the risk of fire electric shock or injury unplug from outlet before servicing Let all parts dry completely before storing 1 800 263 2535 17 18 Maintenance and care Machine care continued 5 The inside of the end caps by the brush rolls can be wiped out with a clean paper towel or if a more thorough cleaning is desired the end caps can be taken off using a Phillips head screwdriver and rinsed clean Replac after cleaning WARNING To reduce the risk of fire 6 Any loose hair or debris can be pulled from the electric shock or injury brush rolls and thrown away For the most unplug from the outlet thorough clean before storage follow directions before servicing on pages 18 amp 19 for removal and replacement of the brush rolls and belts oae za 7 To clean attachments that may have been 1 used remove from hose and rinse in clean running water Dry and replace attach TRA ment in the tool caddy
12. ch ammonia drain cleaner gasoline etc E Do not modify the 3 prong grounded plug E Do not allow to be used as a toy E Do not use for any purpose other than described in this User s Guide E Do not operate the appliance unless the belt door is securely assembled in the location provided E Do not unplug by pulling on the cord E Use only manufacturer s recommended attachments E Always install float before any wet pick up operation E Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage See the cleaning fluid section of this guide E Keep openings free of dust lint hair etc E Do not point attachment nozzle a a people or animals Blssel E Keep appliance on a level surface E Turn off all controls before unplugging E Unplug before attaching the TurboBrush E Be extra careful when cleaning stairs E Close attention is necessary when used by or near children SAVE THESE INSTRUCTIONS THIS MODEL IS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer s warranty GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system If it should malfunction or break down grounding provides a safe path of least resistance for electrical current reducing the risk of electrical shock The cord for this appliance has an equipment grounding conductor and a grounding plug It must on
13. hock or injury E Do not immerse E Use only on surfaces moistened by cleaning process E Always connect to a properly grounded outlet E See Grounding Instructions E Unplug from outlet when not in use and before conducting maintenance or troubleshooting E Do not leave machine when it is plugged in E Do not service machine when it is plugged in E Do not use with damaged cord or plug E if appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized Service Center E Use indoors only E Do not pull or cany by cord use cord as a handle close door on cord pull cord around sharp comers or edges run appliance over cord or expose cord to heated surfaces E Unplug by grasping the plug not the cord E Do not handle plug or appliance with wet hands E Do not put any object into appliance openings use with blocked opening or restrict air flow E Do not expose hair loose clothing fingers or body parts to openings or moving parts E Do not pick up hot or burning objects E Do not pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapor E Do not use appliance in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors E Do not pick up toxic material chlorine blea
14. leanShot button and aim the focused stream onto the stain Allow the formula to soak in for 30 seconds C Run the machine over the stain to extract Repeat as needed until the stain is gone D Rinse if desired Cleaning with attachments Your ProHeat 2X machine comes equipped with a hose and at least one attachment for cleaning stairs upholstery and more 1 Important If using to clean upholstery check upholstery tags A Check manufacturer s tag before cleaning W or WS on the tag means you can use your ProHeat 2X If the tag is coded with an X or an S with a diagonal stripe through it or says Dry Clean Only do not proceed with any deep cleaning machine Do not use on velvet or silk If manufactur er s tag is missing or not coded check with your furniture dealer B Check for colorfastness in an inconspicuous place C If possible check upholstery stuffing Colored stuffing may bleed through fabric when wet D Plan activities to allow upholstery time to dry E Vacuum thoroughly to pick up loose debris and pet hair Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds n Bisse www bissell ca Manufacturer s tag 1 800 263 2535 13 Operation Cleaning with attachments continued A w ARNIN G 2 10 11 12 13 Follow the instructions on pages 10 amp 11 for filling the To reduce the risk of 2 in 1 water tank and the fo
15. ly be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances Grounded Outlets A WARN l N G Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service person if you aren t sure if the outlet is properly grounded DO NOT MODIFY THE PLUG If it will not fit the outlet have a proper outlet installed by a qualified electri cian This appliance is designed for use on a nominal 120 volt circuit and has a ground ing attachment plug that looks like the plug in the drawing above Make certain that the appliance is connected to an outlet having the same configuration as the plug No plug adapter should be used with this appliance 1 800 263 2535 CleanShot Trigger Product view Power Switch Heater Switch Extra Long Flex H Power Cord n Upper Handle Easy Carry Handle Heat ndicator Light Tank Carry Handle ReadyTools Detent Pedal Dial 2 in 1 Water Tank CleanShot Lower Base Dry Aire Easy To Remove sss Edge Sweep Brushes Nozzle A 4 www bissell ca Bissel 1 800 263 2535 Hose Secure Latch TurboBrush Storage Crevice Tool Holder Lower Hose Rack WARNING To reduce the risk of fire and electric shock due to internal component damage use only BISSELL cleaning fluids intended for use with the deep cleaner Non BISSELL clea
16. mixes hot tap water with the BISSELL formula Simply choose one of the 4 settings heavy traffic normal clean light clean or water rinse and the ProHeat 2X will adjust the right amount of cleaning solution to mix with the heated water to fit your cleaning need Having a separate solution tank from the water tank also allows no waste of formula Because the water and solution are stored separately they are not mixed until you are ready to clean When your Cleaning job is finished the formula can be stored ready to use in your machine for the next time located on upper handle Bissel www bissell ca 1 800 263 2535 Special features CleanShot The CleanShot feature gives you the ability to tackle tough stains with the push of a button Cleaning solution is sprayed in a concentrated stream penetrating the stain and allowing for better cleaning focus Simply spray and suction and the stain is gone CleanShot is especially effective for spots and stains that would otherwise take a lot of deep cleaning cycles to remove It allows the cleaning formula and machine to do the work for you Flow Gauge Dry Aire The Dry Aire system spreads hot air across the carpet to aid in drying The feature runs while CleanShot your machine is powered Heated air is distributed eanono from the bottom and back of the machine and blown across the carpet while you clean Flow Gauge Dry Aire The flow gauge is loca
17. mula tank 5 Empty 2 in 1 water tank Refill heavy duty bladder with clean hot tap water and replace 6 Tum the machine OFF O allowing red float door to release into the open position Turn unit back ON 1 to continue cleaning Be sure your forward and backward strokes are done at a slower pace 1 800 263 2535 Troubleshooting Other maintenance or service not included in the manual should be performed by an authorized service representative Thank you for selecting a BISSELL product Please do not return this product to the store For any questions or concerns BISSELL is happy to be of service Contact us directly at 1 800 263 2535 BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 263 2535 Monday Friday 8 a m 10 p m ET Saturday 9am 8p m ET Or write BISSELL Canada Corporation Box 1003 Niagara Falls ON L2E 6W2 ATTN Consumer Services Or visit the BISSELL website www bissell ca or www 2Xbissell ca When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of date of purchase in the event of a warranty claim See Warranty on page 24 for details www bissell ca EN 1 800 263 2535 21 Replacement parts BISSELL ProHeat 2X Continued Item Part No
18. ning solutions may harm the machine and void the warranty Keep plenty of genuine BISSELL 2X Multi Allergen Formula on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and will void the warranty gt f BISSELL BISSELL BISSELL BISSELL BISSELL BISSELL 2X Fiber 2X Multi Alergen 2X Pet Stain and 2X Professional 2X Hard Tough Stain Cleansing Removal Odor Removal Deep Cleaning Floor PreCleaner Formula with Formula with Formula with Formula with Solutions Scotchgard Scotchgard Scotchgard Scotchgard Formula Protection Protection Protection Protection Bissell www bissell ca 1 800 263 2535 5 Assembly ZA WARNING Do not plug in your Your ProHeat 2X comes in three easy to cleaner until you have assemble components completely assembled it per Upper Handle the following instructions Lower Handle and are familiar with all Tool Caddy instructions and operating The only thing you will need_to assemble your procedures cleaner is a Phillips head screwdriver 1 Slide upper handle onto lower handle 2 Screw 3 screws into the marked holes 3 Place upper hose rack onto back of upper handle and secure with tapered screw 4 Place lower hose rack onto back of upper handle by pushing in and sliding down until it snaps into place 5 Snap tools into the tool caddy as shown in figure 5 6 Wrap
19. o you can clean whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and void the warranty A lssell 1 1 www bissell ca a 1 800 263 2535 12 Operation Carpet cleaning Continued 6 7a 7b 7c 7d www bissell ca After cleaning you may want to turn the Custom Clean dial to rinse to give your carpeting a final water only rinse This will ensure thorough removal of embedded dirt loosened by the deep Cleaning formula BISSELL deep cleaning for mulas contain an anti resoiling agent that helps your carpets repel dirt and keeps them look ing good longer Remove the tank from the base of the machine by lifting up on the tank carry handle Carry like a bucket to a utility sink or outside where you will dispose of the dirty water Unlatch the top of the tank from the bottom by lifting up on the tank latch which is located on the back of the tank Remove the top of the tank by lifting up on the handle Note how the lip on the top tank separates from the groove in the bottom tank This placement is important when putting the tank back together Lift the bottom portion of the tank pour out dirty water toward the sink through the triangular shaped opening in the corner of the tank Note You may notice hair amp debris deposits on the carpet or in the tank that were loosened by the Cleaning action especially with newer
20. rmula tank injury be extra careful Set ReadyTools dial to the hose attachments setting when cleaning stairs ee Make sure machine is This will allow spray and suction from the hose secure and level Set custom clean dial for heavy traffic normal clean light clean or water rinse as desired Attach the cleaning tool to the end of the hose 5 Plug in and tum on the power switch and heater fdesired muunga N 9 Clean by pressing the trigger to spray solution onto ro the area to be cleaned Slowly move the tool back an and forth over the soiled surface Release the trigger 9 to suction soiled water Continue to clean in the area working in small sections until no more dirt can be 3 removed Rinse optional and suction as needed s Caution Do no overwet Remove and rinse tools in clean running water 10 Dry and replace in the tool caddy It is recommended that you suction clean water from a bowl to rinse out the hose Before replacing lift end of hose and stretch out to A ensure all water is cleared from hose EN Coil flex hose around the tool caddy Empty 2 in 1 water tank and rinse out following the instructions on page 12 Return ReadyTools dial to floor setting A za Bissell 14 www bissell ca 1 800 263 2535 Operation Stain removal Do Not Delay Attending to an accident soon after it occurs ensures the most optimal clean Leaving it for an extended period of time may
21. shes do not turn Possible Cause 1 The belt is off or broken 2 The unit is in the upright position 3 Circuit breaker may have tripped Cleaner not picking up solution Possible Causes 1 ReadyTools dial may be at wrong setting 2 Tank may not be seated properly 3 Tank may not be assembled properly 4 Solution or 2 in 1 water tank is empty 5 2 in 1 water tank has picked up maximum dirty water and red float door has closed 6 Red float door in the tank may have closed as a result of bumping an object or moving machine back and forth too quickly Bissell www bissell ca a Remedies 3 Turn power OFF O Remove and reseat tank 4 Turn power OFF O and then back ON 1 Wait one minute then depress Trigger Remedies 1 Turn power OFF O and unplug unit from outlet Follow instructions on page 18 2 Brushes only rotate when unit is reclined using the detent pedal 3 Turn the machine OFF O and unplug from outlet Check to see if foreign object is caught in brush roll Remove object Plug machine back in to reset circuit breaker Remedies 1 Set ReadyTools dial to either FLOOR CLEANING or TOOLS setting 2 Pick up both the 2 in 1 water tank and formula tank and reseat them so they fit snugly on the unit 3 Check to make sure the lip of the nozzle is securely hooked into the groove on bottom of Tank see page 10 4 Check fluid levels in heavy duty bladder and for
22. stairs or for those creases close to the baseboards turn knob to TOOLS and choose the attachment appropriate for the job Attach tool to the flex hose and you are ready to go Be sure to turn knob back to FLOOR CLEANING when done RNS Scotchgard Protector Carpet protection applied at the mill typically wears down over time from heavy foot traffic and everyday cleaning including deep cleaning To help restore this important protection only BISSELL offers deep cleaning formulas with Scotchgard protector This offers extra protection against dirt and tough stains to keep your carpets looking good longer To maintain your Scotchgard 5 year limited stain warranty you no longer are required to hire a professional By using your BISSELL ProHeat machine with BISSELL formulas containing Scotchgard protector every 12 months your carpet warranty from 3M remains in effect No other home deep cleaning system can do this for you Refer to the Scotchgard protector warranty for details Operation Before you clean 1 Plan activities to give your carpet time to dry 2 Move furniture to another area if cleaning an entire room optional 3 Vacuum area with a dry vacuum cleaner thoroughly before deep cleaning 4 Plan your cleaning route to leave an exit path It is best to begin cleaning in the comer farthest from your exit Bissel 1 800 263 2535 10 Operation Before you clean continued
23. t should require service Call BISSELL Consumer Services at the number listed below or visit the BISSELL website www bissell ca to locate a BISSELL Authorized Service Centre in your area If there are no authorized BISSELL Service Centres in your area a BISSELL Representative at canada custhelp bissell ca or at the phone number below will issue you a Return Authorization Number and a pre paid mailing label to return the unit to BISSELL for warranty repair The machine should be returned with a photocopy of your proof of purchase Your dated sales receipt is your warranty do not send original If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website www bissell ca E mail canada custhelp bissell ca Or Call BISSELL Consumer Services 1 800 263 2535 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Canada Corporation Box 1003 Niagara Falls ON L2E 6W2 ATTN Consumer Services BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW IN
24. ted on the rear cover of your unit and is a convenient performance feedback indicator The flow gauge will spin when the trigger is depressed and e There is liquid in both the clean water tank and the formula tank OR e Custom Clean is set to rinse and there is water in the clean tank The flow gauge will stop spinning when e The trigger is let go e The unit runs out of clean water e The unit runs out of cleaning formula 2 in 1 water tank Our 2 in 1 water tank full capacity system is designed with a heavy duty bladder inside for clean water As you clean the clean water in the bladder will empty and mix with the cleaning formula Dirty water pulled out of your carpets will collect around the outside of the bladder so that clean and dirty water are always kept separate This allows the user to maximize tank space yet only carry one tank to and from the sink for emptying and filling A Bissell www bissell ca A 1 800 263 2535 www bissell ca Special features Easy to remove and clean nozzle Now cleaning up your machine after the cleaning process is easier than ever Simply remove the 2 in 1 Tank and remove the screw to pop out the nozzle for rinsing in the sink Dirt loose carpet fibers and remaining pet hair or fuzz get washed away in a snap ReadyTools dial This provides either floor cleaning or above floor cleaning with the turn of a knob If choosing above floor cleaning for upholstery
25. turn the power and heater switches to the ON 1 position Allow 1 minute for the built in heater to warm up before Cleaning The ProHeat 2X will be fully warmed and will provide optimal performance after a minute of continuous heated cleaning Cleaning Strokes While pressing the trigger make one slow forward wet pass and another 6 one back Let the built in heater formula and DirtLifter PowerBrushes do the work for you Caution Do not overwet Take care not to run over loose objects or edges of area rugs Stalling POWer Switch Heater Switch brush may result in premature belt failure Note Your machine is equipped with a circuit breaker that will automatically shut A n off the brush if a large or loose object is WA R N l N G caught in the brush roll If that happens be To reduce the risk of fire and sure to unplug your machine remove the electric shock due to intemal foreign object and then plug the machine component damage use only back in to reset the circuit breaker BISSELL cleaning fluids intended Release the trigger and make one slow forward and backward pass over the same area to remove any residual dirty water and aid in drying Repeat cleaning passes until solution being pulled up appears clean Continue passes without pressing the trigger until you can t see any more water being pulled up for use with the deep cleaner Keep plenty of genuine BISSELL 2X Multi Allergen Removal Formula on hand s
26. y formula remains in the formula tank pour it back into the Hard Floor Solutions bottle for use the next time 14 Rinse out the formula tank A Bissell www bissell ca ZX WARNING To reduce the risk of fire and electric shock when cleaning a hard floor the BISSELL hard floor tool 203 5642 must be used and it must only be used with BISSELL Hard Floor Solutions or BISSELL 2X Hard Floor Solutions cleaning fluid intended for use with this appliance 1 800 263 2535 Maintenance and care Machine storage Once your cleaning is complete make sure the 2 in 1 water tank is emptied rinsed out and dried before the next use The formula tank can remain filled and ready to go Note Store cleaner in a protected dry area Since this product uses water it must not be stored where there is a danger of freezing Freezing will damage internal components and void the warranty Machine care For best results a few simple steps can assure your machine is well maintained after your Cleaning is complete 1 Turn power and heater switches OFF 0 Unplug the machine and wrap the power cord 2 After emptying the 2 in 1 water tank rinse it out at a faucet with running hot tap water taking care to clean underneath the heavy duty bladder and all around it 3 The top half of the tank can be rinsed clean through the nozzle area Also pop out the red filter underneath the top half of the tank and rinse th
27. y maneuver the top of the tank To attach the top part of the tank to the bottom carefully hook the lip on the top tank into the groove on the bottom tank 1e Fasten tanks together by securing the latch in the back Note Remember to secure the tank latch in the back and test to make sure it is secure before picking up the tank alssell www bissell ca ED ATTENTION Some Berber carpets have a tendency to fuzz with wear Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition Please see Stain Removal instructions on page 15 Lip Groove underside of bottom tank 1 800 263 2535 Operation Carpet cleaning continued 1 2 Remove formula tank from back of machine Fill the formula tank by first unscrew ing the cap and insert Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine Fill water up to water line and then fill up to formula line with BISSELL 2X concentrated formula Replace the cap and insert Place formula tank into the slot in the back of the machine for a snug fit Set Custom Clean Dial Simply choose one of the 4 settings heavy traffic normal clean light clean or water rinse and the ProHeat 2X will adjust the right amount of cleaning solution to mix with the heated water to fit your cleaning need Set ReadyTools Dial to the floor cleaning setting Plug into a proper outlet and
28. ze bottle of Hard Floor Solutions formula 7 62E5 C D 2X Fiber Cleansing Formula with Scotchgard Protection 8 99K5 C 2X Pet Stain and Odor Removal Formula with Scotchgard Protection 9 8905 C D 2X Multi Allergen Removal Formula with Scotchgard Protection 10 14N3 C 2X Professional Deep Cleaning Formula with Scotchgard 11 8117 2X Hard Floor Solutions Formula 12 400 D Tough Stain Precleaner Bissell www bissell ca pe 1 800 263 2535 23 24 Warranty BISSELL ProHeat 2X Healthy Home If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described below Limited ONE Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Canada Corporation will repair or replace with new or remanufactured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part See information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to routine maintenance components such as belts or brushes Damage or malfunction caused by negligence abuse or use not in accordance with the User s Guide is not covered If your BISSELL produc
Download Pdf Manuals
Related Search