Bissell 6801 User's Manual
Contents
1. Using a screwdriver remove the one screw as shown and lift off the lens O Remove the bulb from the socket by pushing in gently and turning it towards brush Install the new bulb by pushing it gently into the socket and turning away from brush 5 Reposition lens and secure with the one screw TurboBrush Maintenance Select Models Only The TurboBrush should be checked regularly for clogs or debris wrapping around the brush roll Unplug vacuum from electrical outlet If a clog is present or debris is visible unscrew the two screws on the back of the TurboBrush to remove the faceplate and clear any obstructions on the belt cover Lift the belt cover Remove the brush roll from the drive belt and clean debris Reposition the drive belt on the brush roll Place ends of brush roll in slots on sides as shown Reposition belt cover and secure with shorter screw Reposition faceplate and secure with two longer screws To clean debris from the brush roll remove the screw located ug603 5540 3750 905 indd 12 To reduce the risk of electric shock turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks 10 3 05 3 47 58 PM Clearing Clogs Low suction or poor pickup may be due to a clog in the vacuum cleaner If you notice a change in the sound of the motor or a reduction in the spinning action check for2. TurboBrush Select Models Use rotating brush action for small areas such as stairs and upholstery Note Press gently when using TurboBrush to gain maximum cleaning Too much pressure could cause the brush to stop rotating Deluxe Bare Floor Tool Select Models Use for bare floors Swivel head turns to get into tight spaces and fits under cabinets Note The Deluxe Bare Floor Tool does not store on board All items may not be included with your model More tools are available to order please refer to page 15 Cleaning With The Detachable Canister The Detachable Canister feature makes it possible to easily take the powerful cleaning action of your BISSELL Lift Off to stairways auto interiors and other hard to reach areas of your home Before detaching the Canister your Lift Off must be in its fully Upright Position You do not need to turn off the power first Press the Release Button at the top of the Canister Handle and lift the Canister to remove 2 Detach the Vacuum Hose from the Hose Grip Base at the back of the Canister Attach the desired tool s to the Hose Grip at the end of the Vacuum Hose GD When you re done remove the tool s and reconnect the Hose to the Hose Grip Base 5 Return the Canister to the Powerfoot by aligning the feet on the front with the bumps on the foot of the Upright Vacuum Push the Canister toward the vacuum frame until it clicks into place
3. A Bissell Lift Off USER S GUIDE 3750 6595 6801 SERIES 3 Kal BAGLERS A ETETE 4 6 FAA AA O 6 9 TAWA eels BAALE AL Fo w 2 10 13 DEMIE 14 Bnei 15 BE la 15 Eri M 16 Been ug603 5540 3750 905 indd 1 10 3 05 3 47 49 PM Thanks For Buying A BISSELL Lift Off We re glad you purchased a BISSELL Lift Off Vacuum Everything we know about floor care went into the design and construction of this powerful high tech home vacuuming system Your BISSELL Lift Off is well made and we back it with a limited comprehensive one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your BISSELL Lift Off Thanks again from all of us at BISSELL Am eA 4 Kr Mark J Bissell President and Chief Executive Officer ug603 5540_3750_905 indd 2 10 3 05 3 47 53 PM IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM Always connect to a polarized outlet left slot is wider than right Unplug from outlet when not in use and before conducting mainte
4. Website or E mail www bissell com Use the Customer Services tab Or Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION sBsissell OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE 2005 BISSELL Homecare Inc Some states do not allow limitations on how long an implied warranty lasts Grand Rapids Michigan so the above limitation may not apply to you All rights reserved Printed in Korea Part Number 603 5540 Rev 9 05 Visit our website at www bissell com ug603 5540_3750_905 indd 16 10 3 05 3 48 02 PM
5. and slip Power Cord You may want to turn the Brush Switch OFF 0 from Upper and Cord Wraps for bare floor cleaning or other delicate surfaces Note Your BISSELL Lift Off vacuum is equipped Brush with a special internal switch that turns the Rotating Brush off whenever the unit is in the Upright position Handle Positions 0 Upright For storage and above floor cleaning with tools 2 Normal Cleaning Press the Handle Release Pedal with your foot to recline ug603 5540 3750 905 indd 6 10 3 05 3 47 55 PM Power Height Adjustment The Powerfoot on your BISSELL Lift Off can be lip Before cleaning under adjusted to clean several floor surfaces low furniture check NOTE For optimal cleaning performance adjust to area first for objects the lowest practical setting If your cleaner is that might harm the difficult to push adjust to the next higher setting unit or block the Vacuum Hose Place Handle in Upright Position Turn Height Adjustment Knob to desired setting Lowest Setting For bare floors Medium Settings For short and medium pile carpets Highest Setting For plush pile carpet NOTE You may also adjust the setting while in the Normal Cleaning Position Special Tools Your BISSELL Lift Off is not only a powerful floor vacuum cleaner it s also a versatile stairs and above floor vacuum when you select one of the special tools
6. When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It is your warranty Replacement Parts BISSELL Lift Off Series You may purchase replacement parts from your retailer by calling BISSELL Consumer Services or by visiting our website To locate a retailer near you or to place an order using Visa MasterCard Discover or American Express call BISSELL Consumer Services 1 2 3 1 800 237 7691 cp Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or visit our Website www bissell com Item PartNo Part Name 1 3200 Style 8 Drive Belt 2 Pack 2 203 1007 Headlight Bulb 5 203 1063 O Crevice Tool 4 203 1099 Dusting Brush Upholstery Tool 5 203 6624 Stair Cleaning Tool Select Models 6 T 8 9 203 6625 Telescoping Extension Wand f 203 2081 Deluxe Bare Floor Tool Select Models 203 1227 TurboBrush Select Models 9 203 2082 Bracket Assembly for TurboBrush Select Models 10 203 5542 Shoulder Strap Select Models 10 11 12 13 14 15 11 203 6633 Vacuum Hose Select Models m 12 203 2073 Twist n Snap Hose Select Models lt E or 13 203 6619 Brush Roll Red hey 14 203 2085 Brush Roll Grey 15 203 2074 Brush Roll Taupe i 16 3093 Style 7 8 Upper Tank Filter Pre Motor Filter Set 6 7 17 3091 Style 8 HEPA Media Post Motor Filter
7. a screwdriver Attach Handle To Vacuum Locate the vacuum Handle and remove the screw packet taped to the base of the Handle 2 Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body Check to be sure the Handle is fitted to the vacuum body If there is a gap in front continue to push firmly until the Handle is flush O Insert two of the screws from the screw packet into the existing hole Tighten securely with a screwdriver Attach Vacuum Hose and Tools 0 Position the Hose Assembly on the back of the canister as shown 2 Attach the Hose to the vacuum Standard Models Use the remaining two screws from the packet Tighten securely with a screwdriver Twist n Snap Hose Models Select Models Position the Twist n Snap Hose assembly on the vacuum and line up the tabs on the base of the hose with the corresponding notches Turn the Twist n Snap Hose to the right to lock into place Twist n Snap Hose Models ug603 5540 3750 905 indd 5 10 3 05 3 47 54 PM Attach Vacuum Hose and Tools Continued Slide the end of the Hose Grip onto the Hose Grip Base Place the Hose into the Hose Clip NOTE The Powerfoot will not operate effectively unless the Hose is firmly attached to the base Combination Tool S IN m CCC O onap the Telescoping Extension Wand Crevice Tool and Combination Tool into sto
8. clogs Unplug cleaner from electrical outlet Empty Dirt Container Suction Check Upper Tank for build up or clogs Inlet O Remove the Upper Tank and check the suction inlet for a clog Q Grasp the Hose Grip and lift to separate from the suction opening Check for a clog in the Base or the Hose For Models with the Twist n Snap Hose Release the hose from the vacuum by turning to the left Straighten the hose and unclog with a long narrow object O If the clog persists follow the instructions for Checking the Rotating Brush on page 11 and inspect the Air Passageway for obstructions Thermal Protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the main vacuum motor will stop operating If this happens proceed as follows Turn the cleaner OFF 0 and unplug from electrical outlet 2 Check the Upper Tank area Pre Motor Filter and Post Motor Filter for dirt accumulation Refer to the Clearing Clogs section 14 When the motor cools for approximately 30 minutes the thermal protector automatically N resets and cleaning may continue If the thermal C a u tI O n s protector continues to activate after following the To reduce the risk of above steps your cleaner may need servicing Call iniurv from movin BISSELL Consumer Services or visit the website ai tum off kalk J Note T
9. ug603 5540 3750 905 indd 8 NOTICE While vacuuming certain carpets and low humidity conditions may generate small static discharges The discharges are entirely harmless and are not associated in any way with the main power supply 10 3 05 3 47 56 PM Shoulder Strap Select Models Only The Shoulder Strap may be used while cleaning with the Detachable Canister dg attach the Shoulder Strap wrap the Velcro ends attached to the bottom of the strap securely around the Canister handle as shown ite length of the strap may be adjusted as required for comfort Clean Filter Indicator Select Models Only The Clean Filter Indicator tells you when airflow in the vacuum is reduced due to dirty filters or a clog in the hose The Clean Filter Indicator will remain green until the airflow is reduced At that time it begins to change to red When it is fully red the airflow is significantly reduced or blocked Follow the steps on pages 10 11 to clean your filters All filters in the vacuum should be cleaned or replaced when the Clean Filter Indicator turns red lf the indicator remains red after all filters have been cleaned follow the steps on page 13 to check for and clear clogs Power Cord Storage While the vacuum is in use warm air is emitted through the Post Motor Filter on the back of the Canister The bottom of the Canister may also become warm When using the shoulder strap to a
10. Note The tools can be used with the vacuum in the Upright Position or with the Detachable Canister Detach the Vacuum Hose by grasping the Hose Grip and lifting to separate from the Hose Grip Base 2 Attach tools by firmly pushing onto Vacuum Hose or Telescoping Extension Wand Combination Dusting Brush Upholstery Tool Two types of cleaning tools are included in one attachment Ec rotate for desired tool W Use Brush side to dust furniture blinds books lamps shelves and baseboards W Use Upholstery side for curtains draperies cushions fabrics Crevice Tool Use in tight narrow spaces Stair Cleaning Tool Select Models AN a Use for stairs area rugs and other small carpeted areas CAUTI 0 N m This tool can also be used for bare floors ie k gk anl leb on i oor in its fully Upright Position Note The Stair Cleaning Tool does not and make sure it is locked into store on board place before removing Canister or when using tools Placing the Lift Off in its full Upright Position automatically stops the rotating brush ug603 5540_3750_905 indd 7 10 3 05 3 47 55 PM Special Tools Continued Telescoping Extension Wand Use with desired attachment for a longer reach To extend the Wand twist the collar to Unlock position and push away from you Twist the collar to the Lock position to lock into place To retract twist to unlock pull toward you and twist to relock
11. acing O The Upper Tank and Louvers may also be wiped clean with a damp cloth Note For easier access the entire Upper Tank may be removed by turning the knob on the back of the cleaner to unlock and pulling the entire tank straight out ug603 5540_3750_905 indd 10 10 3 05 3 47 57 PM Cleaning The Pre Motor and Post Motor Filters Maintenance Use only BISSELL Style 8 Replacement Filters in your BISSELL Lift Off Unplug the cleaner from electrical outlet 12 The Pre Motor Filter protects the motor from dirt particles It is located in the slide out tray underneath the Dirt Container If the filter becomes dirty pull out the tray lift out the filter and clean This filter may be hand washed in cold water with mild detergent Rinse well and air dry thoroughly before replacing The HEPA Media Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the back of the cleaner If the filter becomes dirty open the door remove the filter and replace The HEPA Media Filter is not washable Rotating Brush and Drive Belt Maintenance indore Use only BISSELL Style 8 Replacement Belts 3200 in your BISSELL Lift Off Check your vacuum cleaner s Rotating Floor Brush and Drive Belt regularly for debris wear or damage Debris filters or without all filters in place can wrap around the brush and hamper its ability to e effectively clean your
12. carpet ekl e 0 Unplug cleaner from electrical outlet off vacuum cleaner and disconnect Power Plug Remove Detachable Canister from vacuum cleaner from electrical outlet Recline Handle and turn vacuum cleaner over so bottom side is up O Remove the six screws as shown with a Phillips head screwdriver Lift the Brush Cover off Q Lift the Rotating Floor Brush to remove Clean strings hair and other debris from the Brush paying special attention to the brush ends 6 Check Air Passageway for obstructions Remove any debris from this area Clean debris from the Motor Pulley and Drive Belt areas Check Drive Belt carefully for wear cuts or stressed areas If any damage is present discard old Drive Belt and replace ug603 5540_3750_905 indd 11 Air Passageway 10 3 05 3 47 58 PM Rotating Brush and Drive Belt Maintenance Continued O Place one end of the new Drive Belt over Motor Pulley and the other end over the Brush in the space between the bristles QD Pull the Brush firmly to stretch the Drive Belt and place ends of Brush down into slots on sides as shown Turn Brush several times by hand to center the Drive Belt Reposition Brush Cover and screws Tighten screws securely Replace Light Bulb Use only BISSELL Replacement Bulb 203 1007 in your BISSELL Lift Off Unplug cleaner from electrical outlet Remove Detachable Canister and recline Handle of vacuum
13. e Cord Wrap au l Clean Filter Crevice Tool Indicator Select i Models Only elescoping Louvers Filter HEPA Media Extension Wand Frame Post Motor Filter Power Cord Upper Tank Filter Inside Louvers Hose Grip Upper Tank ear Dirt Handle Release Pedal Container E Pre Motor Lock n Seal Hose Grip Base Filter Lever Headlight i Height Adjustment Knob Powerfoot Furniture Protection Guard Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures ug603 5540_3750_905 indd 4 10 3 05 3 47 53 PM How To Use This Guide This User s Guide has been designed to help you get the most satisfaction from your BISSELL Lift Off You ll find assembly and operating instructions AN safety precautions as well as maintenance and WARN N G troubleshooting instructions Please read this Guide Plastic film can be thoroughly before assembling your vacuum cleaner dangerous To avoid danger Pay particular attention to the product diagram of suffocation keep away assembly instructions and part names Locate and from babies and children organize all parts before assembly Familiarize yourself with the parts and where they fit Following this User s Guide will greatly enhance your ability to get the most performance from your BISSELL Lift Off for many years How To Put It Together The only tool you ll need to assemble your vacuum cleaner is
14. gt Om gt ug603 5540 3750 905 indd 15 10 3 05 3 48 00 PM This warranty gives you specific legal rights and you may also have other rights which may vary from state to State If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail teleohone or regular mail as described below Limited One Year Warranty subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part see information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered lf your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area f you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services
15. he thermal protector controls the main cleaner and disconnect vacuum motor only not the brush motor If the Power Plug from thermal protector activates the brush will i l electrical outlet continue to operate normally however there will be no suction ug603 5540 3750 905 indd 13 10 3 05 3 47 59 PM gt Troubleshooting Vacuum cleaner won t run Possible Causes Power cord not plugged in Blown fuse tripped breaker Thermal protector activated No Power at Rotating Floor Brush Possible Causes 1 Canister is not securely seated Brush Switch turned to Off Vacuum is in upright position Vacuum cleaner won t pick up dirt Possible Causes Incorrect Height Adjustment Hose not attached to suction opening Crack or hole in Hose O Drive Belt broken worn or off motor pulley O Rotating Floor Brush bristles worn Rotating Floor Brush jammed Clog in vacuum O Dirt Container full Dirt Container or Upper Tank not installed properly M Filters are dirty Vacuum cleaner is difficult to push Possible Causes 1 Incorrect Height adjustment Visible dirt escaping from cleaner Possible Causes Dirt Container full Filter missing or installed incorrectly Dirt Container installed incorrectly ug603 5540_3750_905 indd 14 A WARNING To reduce the risk of injury from moving parts and or electrical shock turn Power Switch OFF and disconnect polarized plug from e
16. ilter every six months NOTE More freguent filter cleaning may be necessary if you are vacuuming new carpet fine dust or have allergy concerns For maximum cleaning Follow the instructions on the following pages to per performance check and form these simple maintenance steps Clean or replace all filters as suggested Empty Dirt Container The Dirt Container needs to be emptied when the dirt reaches the Full line on the side of the Container Unplug cleaner from electrical outlet 2 Slide the Lock n Seal Lever to the Unlock position Grasp handle and pull the Dirt Container straight out to remove from vacuum O Empty dirt into garbage container Put the Dirt Container back in the vacuum and slide the lever to the Lock position Note The Dirt Container may be washed in warm water with a mild detergent Make sure it is completely dry before replacing Cleaning The Upper Tank amp Filter Use only BISSELL Style 8 Replacement Filters in your BISSELL Lift Off Unplug the cleaner from electrical outlet 2 The Upper Tank Filter can be reached by removing the Dirt Container reaching underneath the Upper Tank and turning the rim of the Filter Frame to unlock Pull straight down to remove Brush the dirt off the Louvers and Upper Tank Filter The foam Upper Tank Filter may be removed and hand washed in cold water with mild detergent Rinse well then air dry thor oughly before repl
17. lectrical outlet before performing troubleshooting checks Remedies Check electrical plug O Gheck Replace fuse or reset breaker Allow cleaner to cool for 30 minutes see pg 13 Remedies 1 Remove Canister and replace making sure that it clicks into place Make sure Brush Switch is in On position Recline vacuum to operate brush Remedies Adjust Powerfoot to correct height setting Grasp Hose Grip and firmly push onto the base Check Hose and replace if needed Reposition or replace Drive Belt see pg 11 12 O Replace brush O Remove brush and clean debris from brush ends Q Follow instructions on pg 11 for clearing clogs Empty Dirt Container O Position correctly and lock in place fp Check and clean or replace Upper Tank Pre Motor and Post Motor Filters Remedies Adjust Powerfoot to correct height setting Remedies Empty Dirt Container Check Upper Tank Pre Motor and Post Motor Filter for correct installation Pull out and re insert Dirt Container correctly 10 3 05 3 48 00 PM BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com
18. nance ZAWARNING To reduce the risk of fire electric shock or injury M Do not modify the polarized plug to fit a non polarized outlet or extension cord M Do not leave vacuum cleaner unattended when it is plugged in W Unplug from outlet when not in use and before servicing M Do not use outdoors or on wet surfaces M Do not allow children to operate vacuum cleaner or use as a toy WE Close attention is necessary when used by or near children W Do not use for any purpose other than described in this User s Guide W Use only manufacturer s recommended attachments Do not use with damaged cord or plug W if appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized service center mM Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces W Do not unplug by pulling on cord To unplug grasp the plug not the cord W Do not handle vacuum cleaner or plug with wet hands W Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow ug603 5540_3750_905 indd 3 W Keep hair loose clothing fingers and all parts of body away from openings and moving parts W Turn off all controls before plugging or u
19. nplugging vacuum cleaner W Use extra care when cleaning stairs W Unplug before attaching the TurboBrush WE Do not pick up flammable materials lighter fluid gasoline kerosene etc or use in the presence of explosive liguids or vapors W Do not pick up toxic material chlorine bleach ammonia drain cleaner etc W Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors W Do not pick up hard or sharp objects such as glass nails screws coins etc W Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes M Do not use without filters in place W Use only on dry indoor surfaces W Keep appliance on a level surface SAVE THESE INSTRUCTIONS FOR FUTURE USE THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a proper outlet Do not change the plug in any way This model is for household use only 10 3 05 3 47 53 PM Comfort Grip Handle Cord Clip Dusting Brush Upholstery Tool Stretch Hose Release Button Hose Clip Quick Releas
20. rage clips as shown Q On Board TurboBrush Select Models Only The TurboBrush Bracket slides onto the Hanger on i the front of the Handle Attach the Bracket by Crevice Tool aligning the slots with the rectangular part on the Hanger as shown and pulling down until it is locked into place Note If you do not wish to store the TurboBrush on your Lift Off vacuum the Bracket may be hung on a wall for storage and the Hanger may be removed from the vacuum Place the TurboBrush in the Bracket by aligning the small holes near the brush roll with the tabs at the bottom of the Bracket and snap the TurboBrush into place How To Use Your BISSELL Lift Off A CAUTION E uang your mel ne H i sure that the Dirt Container an Power Switch Brush Switch Upper Tank are in locked position and that all filters Upper Tank The Power Switch is located just below the handle mii a ru on the front of the Detachable Canister Push the vacuina without hese iers rocker switch ON I to vacuum and OFF 0 when cleaning is complete The Brush Switch is located just below the handle on the front of the Detachable Canister next to Your vacuum features a Quick Release the Power Switch This switch turns the Rotating Cord Wrap To remove the Power Cord Brush on and off The Brush Switch should be in quickly and easily rotate the Upper Cord the ON I position for normal carpet cleaning Wrap towards floor
21. void discomfort position the Canister so that these parts are not directed towards or touching your body ug603 5540_3750_905 indd 9 When you are done using your BISSELL Lift Off return it AN i to the Upright position and store the Power Cord CAUTION n Do not press the Release Button Turn vacuum cleaner off 0 while using the Carrying Handle to transport the vacuum cleaner The Canister could detach causing the rest of the vacuum to fall Unplug Power Cord by grasping the polarized plug NOT the cord and disconnect from outlet Loop Power Cord around Cord Wraps on side of the Canister QU molded plug to Power Cord to secure Transporting Cleaner dg move your vacuum cleaner from room to room put the Handle in the Upright Position tilt the cleaner back on its rear wheels and push forward Th cleaner can also be moved by using the Carrying Handle on the Detachable Canister 10 3 05 3 47 57 PM How to Maintain Your BISSELL Lift Off To maintain maximum cleaning performance the A WARNING following maintenance steps must be performed To reduce the risk of electric Empty the Dirt Container when the dirt reaches the Full line m elele ll on ihe side from electrical outlet before i erforming maintenan Check the Upper Tank and Pre Motor Filters at least once a troubleshooting kle month and clean and replace as needed Replace the HEPA Media Post Motor F
Download Pdf Manuals
Related Search