Bionaire BSF16 User's Manual
Contents
1. ASSEMBLY INSTRUCTIONS Tools Required Phillips Head Screwdriver BASE POLE ASSEMBLY Step 1 Insert the large foot bracket U into the bottom of the lower pole Make sure to align the rectangular plas tic tab with groove inside the pole Slide the foot up approximately two inches and then screw the feet into place Step 2 Insert the small foot bracket X into the bottom of the lower pole Make sure to align the rectangular plastic tab with groove inside the pole Slide the foot up until it touches the bottom of the upper foot bracket Then screw the small foot bracket into place Grill Hub Decorative Cap Security Screw Front Grill Fan Blade Cap Washer Nut Fan Blade Rear Grill Mounting Nut Rear Grill Motor Shaft Motor Housing Speed Control Knob Fan Neck Clasp Screws 2 Extension Pole Clasp Power Cord Clip Extension Pole Pole Cover Extension Pole Bracket S Extension Pole Bracket Height Adjustment Knob T Lower Pole U Large Foot Bracket V Large Foot Extensions W Rubber Feet 4 X Small Foot Bracket Y Small Foot Extensions FAN HEAD ASSEMBLY Step 1 Attach the neck of the fan to the upper extension pole To do this align the extension pole clasps and screw holes up with the corresponding holes on the neck of the fan Once you have the neck adjusted to the angle of the extension pole clasps screw the clasps to the neck of the fan until Secure2. Step 2 Using your screwdriver remove the securing screw that is located inside the Bionaire decorative cap on the grill ring Once you have unscrewed the grill ring put it aside until you are ready to re attach the grills Step 3 Remove the two plastic ties that are holding the rear grill and the fan blade together Discard the two plastic ties and cardboard Step 4 Loosen and take off the rear grill mounting nut H that is attached to the motor housing by turning counter clockwise Step 5 Place the rear grill on the front of the motor housing making sure that the handle on the back of the grill is above the motor housing doing this will align the holes on the grill over the two screws in the housing Then tighten the rear grill mounting nut onto the rear grill by turning clockwise NOTE To know that the rear grill is on correctly there will be one grill clip located at the bottom of the grill Step 6 Place the fan blade onto the motor shaft J making sure to align the flat area on the motor shaft with the flat area in the center of the fan blade Slide the fan blade to the back of the motor shaft until it stops and the motor shaft is protruding Step 7 Insert the washer and tighten the nut onto the motor shaft to secure the fan blade Complete the fan blade assembly by turning the fan blade cap counter clockwise into the matching grooves in the center of the fan blade Step 8 Place the front grill onto the
3. FAN HEAD BASE AND POLE CLEANING Using a soft moist cloth with or without a mild soap solution carefully clean the fan base pole and head Please use caution around the motor housing area Do not allow the motor or other electrical compo nents to be exposed to water FAN STORAGE INSTRUCTIONS Your fan can be stored in the off season either partially disassembled or assembled It is important to keep it in a safe dry location e f stored disassembled we recommend using the original or appropri ately sized box e f stored assembled or partially assembled remember to protect the fan head from dust FAN SERVICE INSTRUCTIONS 1 Do NOT attempt to repair or adjust any electrical or mechanical func tions on this unit doing so will void the warranty 2 lf you have any questions regarding this unit s operation or believe any repair is necessary please call 1 800 788 5350 to speak with a consumer service representative If you need to exchange the unit please return it in its original carton with a sales receipt to the store where you purchased it If you are returning the unit more than 30 days after the date of purchase please see the enclosed warranty WARRANTY Bionaire warrants to the first retail purchaser for FIVE 5 YEARS from the date of original purchase either to repair or replace at its option without charge parts and labor any supplied or manufactured part of this fan which upon inspection by an
4. authorized service center proves to have failed in normal use due to defects in material or workmanship or at its option to replace the unit Operation under conditions other than those recommended or at volt ages other than the voltage indicated on the unit or any attempts by unauthorized personnel to service the unit or modify it will render the guarantee void Bionaire shall not be liable for any personal injury property damage or any incidental or consequential damages of any kind including water damage resulting from defects malfunctions misuse improper instal lation or alteration of the product BIONAIRE EXPRESSLY DISCLAIMS ALL RESPONSIBILITY FOR CONSEQUENTIAL DAMAGES OR INCI DENTAL LOSSES CAUSED BY USE OF THIS PRODUCT The provisions of this warranty are in addition to and not a modification of or subtraction from the statutory warranties and other rights and remedies contained in any applicable legislation and to the extent that any such provision purports to disclaim exclude or limit any such statu tory warranties or other rights or remedies such provisions shall be deemed to be amended to the extent necessary to comply therewith For Warranty Service please call 1 800 788 5350 in North America I BIONAIRE P O BOX 400 MILFORD MA 01757 A Bionaire consumer service representative will help determine which is the best procedure in order for your fan to be repaired Visit our Website www bionair
5. YH BIONAIRE T INFO LINE If after having read this leaflet you have any questions a Pc ee a ADD Wa Or comments on your fan call 1 800 788 5350 in North America Instruction Leaflet Read instructions before operating Retain for future reference A FAN SAFETY PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read all instructions before using the appliance 2 To avoid fire or shock hazard plug the appliance directly into a 120V AC electrical outlet 3 Keep the cord out of heavy traffic areas DO NOT let the cord hang over the edge of a table or counter To avoid fire hazard NEVER put the cord under rugs near heat registers radiators stoves or heaters 4 To protect against electrical hazards DO NOT immerse in water or other liquids Do not use near water 5 Close supervision is necessary when any appliance is used by or near children or by disabled people 6 Always unplug the fan before moving it putting on or taking off parts cleaning or whenever the fan is not is use Be sure to pull by the plug and not the cord 7 Avoid contact with moving parts DO NOT operate without fan grills properly in place 8 DO NOT operate any appliance with a damaged cord or plug if motor f
6. an fails to rotate after the appliance malfunctions or if it has been dropped or damaged in any manner Return appliance to manufact urer for examination electrical or mechanical adjustment or repair 9 DO NOT operate in the presence of explosive and or flammable fumes 10 Use appliance only for intended household use as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons The use of attach ments not recommended or sold by Bionaire may cause hazards 11 DO NOT use outdoors 12 13 Keep unit away from heated surfaces and open flames 14 WARNING To reduce the risk of fire or electric shock DO NOT use this fan with any solid state speed control device Always use on a dry level surface 15 DO NOT attempt to repair or adjust any electrical or mechanical func tions on this unit Doing so will void your warranty The inside of the unit contains no user serviceable parts All servicing should be per formed by qualified personnel only THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC Alternating Current PLUG a plug having one blade wider than the other This plug will fit into the power outlet only one way If the plug does not fit fully into the outlet reverse the plug If it still does not fit contact qualified personnel to install the proper outlet DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY DODOZECAS IOTNMoOOm gt
7. back grill so that the 2 clips on the top of the front grill fit over the rear grill Also ensure that the bottom clip that is attached to the rear grill attaches and fits onto the front grill when assembling the fan head NOTE When attaching the grill ring make sure to have the Bionaire decorative cap where the two ends of the grill ring meet at the bottom center of the grills 3 Step 9 Place the grill ring around the edges of both grills making sure to enclose both edges with the ring Then re attach the Bionaire decorative cap by passing the screw through the hole on the side of the cap and using your screwdriver tighten the grill ring together until the fan head assembly is completely secure FINAL ASSEMBLY Step 1 Insert the extension pole into the lower pole Insert the two brackets Parts R and S into the top of the lower pole Make sure to align the two rectangular plastic tabs with groove inside the pole Slide the brackets down until the pole cover is completely inserted into the lower pole Step 2 Once inserted tighten the screw on the top bracket until it is secure Then tighten the height adjustment knob to your desired height see below instructions for height adjustment Step 3 Pass the power cord though the power cord clip to secure it into place OPERATING INSTRUCTIONS Step 1 Set the fan base on a dry level surface Step 2 Please make sure the Speed Control Knob is in the Off position Plug
8. e com KEEP THIS NUMBER FOR FUTURE REFERENCE L a Z e m gt 428 0102
9. the cord into any standard 120V AC outlet Step 3 The SPEED is adjusted by moving the knob left or right to the desired speed setting The speeds are indicated by the numbers 1 for Low 2 for Medium and 3 for High Step 4 The OSCILLATION Knob is located on the bottom of the fan motor housing To start oscillation pull knob down To stop oscillation push knob up ADJUSTMENT INSTRUCTIONS TILT ADJUSTMENT Step 1 To change the tilting angle of the fan head move the fan head to the desired angle HEIGHT ADJUSTMENT Step 1 Turn the height adjustment knob counter clockwise and slide the fan up or down to the desired position Once you have reached your desired height turn the knob clockwise to lock into position CLEANING MAINTENANCE INSTRUCTIONS Follow these instructions to correctly and safely care for your Bionaire Stand Fan Please remember e Always unplug the fan before cleaning or disassembling e Do not allow water to drip on or into the fan motor housing e Do not use any of the following as a cleaner gasoline thinner benzine See instructions for fan head assembly Step 1 Unplug your fan before cleaning To access the fan blade remove the front grill and fan blade cap Step 2 Clean the fan blade both front and rear grills with a soft cloth moistened with a mild soap solution Dry thoroughly before operating Step 3 Replace the blade tighten the fan blade cap and securely fas ten the front grill
Download Pdf Manuals
Related Search