Avital 3300L User's Manual
Contents
1. SINNOTT AL Model 3300L _ gt Owner s Guide For a period of one calendar year from the date of purchase of this auto security device Directed Electronics promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFES SIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYS TEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the follow ing page After the first calendar year from the date of purchase of this auto security device Directed Electronics promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control module which proves to be defective in workmanship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all pre vious and contemporaneous representations or2. ZONE Number of DEALER INSTALLED LED Flashes DESCRIPTION OPTIONS 1 Instant trigger for optional hood or trunk pin 2 Instant trigger a heavier impact detected by the on board shock sensor 3 Door switch trigger 5 Ignition trigger code hopping 28 The receiver and remotes use a mathematical formula called an algorithm to change their code each time the remote is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the remote in sync with the control unit even if you use the remote control out of range of the vehicle However if the remote has been pressed many times out of range of the vehicle or the battery has been removed it may fall out of sync with the control unit and fail to operate the system To re sync the remote simply press E several times within range of O 2008 directed electronics all rights reserved the vehicle The alarm will automatically re sync and respond to the remote normally high frequency Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phenomenal increase in range even in areas with high radio interference rapid resume logic This Directed system will store its current state to non volatile memory If power is lost and then reconnected the system will
3. NPC has been engaged If you wish to clear the NPC memory turn the ignition on 2008 directed electronics all rights reserved 25 26 The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering you will hear one siren chirp to indicate arming and a second siren chirp to indi cate Bypass Notification A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal monitoring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second Bypass Notification chirp Three seconds after the light turns off however the security system resumes normal monitoring note Bypass Notification does not occur when the sys tem is in Silent Mode or if the notification chirps have b
4. The button will advance the selection downward or select the off set ting Be sure to hold down for five seconds prior to entering timer clock adjust mode operation xx Press once to have the alarm clock on Press twice to have the alarm clock off The remote will revert to normal operation from the set mode when 15 seconds has elapsed without a button entry 2008 directed electronics all rights reserved 15 The remote start system operates at 434 MHz and incorporates Directed s proprietary A S K out board two way transceiver The high frequency combined with Binary Data communication achieves superior range with two way communication system signal paging features 16 A page is the signal the control module sends to the transceiver as confirmation of receipt of a command or alarm system status When the transceiver receives a page it will generate a page notifi cation to the user notifications are audible beeps or the remote vibrates and the LCD icons will display the current system status Command Page When a command arm disarm or auxiliary channel from the transceiver is sent and received the system will send a command page back to confirm receipt Page Recognition Mode The transceiver will leave a zone icon illuminated when it has received a triggered response and will wait for violation recogni tion Press any button on the transceiver the LCD information and alarm page alerts wil
5. recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode 2008 directed electronics all rights reserved 29 proarammina option 30 Programming options control your system s normal operational set up Most options do not require additional parts but some may require installation labor The following is a list of the programmable options with the factory settings in Bold gt Active arming from remote only or passive arming auto matic arming 30 seconds after the last door has been closed Arming disarming siren chirps on or off The ignition controlled door lock feature on or off When this feature is programmed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off Passive door locking with passive arming or active door locking only when arming with the remote Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by a d
6. report Zone 1 gt Trunk Trigger Opening the trunk if connected will instantly sound the siren and flash the lights for the programmed duration and report Zone 1 O 2008 directed electronics all rights reserved 19 gt Ignition Trigger If the ignition is turned on the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and the remote will flash When a Triggered Response is activated the transceiver will gt gt gt Repeat four quick beeps or vibrate for 15 seconds The full trigger alert icon 28 will turn on for 15 seconds The zone icons will turn on and remain on until a transceiver button is pressed clearing the page alert The transceiver will enter page recognition mode and generate alarm page alerts note Icons 13 14 16 and 20 represent alarm system triggered sequence zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configurations section disarming To disarm the security system press a You will hear two chirps and the parking lights will flash twice If the power locks 20 are controlled by the system the doors will also unlock If the siren chirps more than twice and the LED continues to flash after pressing the button the system was triggered in your absence Tamper Alert Refer to the disarming discussion in the Diagnostics Section of this
7. O 2008 directed electronics all rights reserved To replace the battery gently pull the battery cover release tab then slide the door down to expose the battery and remove the expired battery Place the new battery into the transceiver observing the correct polarity When power is returned the transceiver will light all icons in the LCD and generate a musical tone 4 Button Remote Battery Replacement Your remote is powered by a small lightweight 3 volt lithium battery CR2032 that will last approximately one year under normal use When the battery begins to weaken operating range will be reduced and the LED on the remote will dim your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation 2008 directed electronics all rights reserved 9 Directed Electronics Inc 544 Series Tested to Comply C with FCC
8. Panic Mode W Press for 2 seconds and you will enter Panic Mode The siren will sound and the parkin lights will flash for 30 seconds To stop Panic Mode at any time press on the remote again 2008 directed electronics all rights reserved 35 The company behind this system is Directed Electronics Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers Lixected ELECTRONICS Vista CA 92081 www directed com O 2008 Directed Electronics All rights reserved G3300L 2008 12
9. Standards Directed Electronics Inc 477T Series Tested to Comply C with FCC Standards Directed Electronics Inc 474V P S Series Tested to Comply C with FCC Standards Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 10 2008 directed electronics all rights reserved Standard LCD 2 way icon configuration Icon The vehicle interior temperature icon has no functions The numeric display icon will show the hours and minutes Icon The AM PM icon indicates the time before or after noon alarm clock mode icon indicates that the alarm clock mode is active Icon The timer function icon flashes during timed functions including parking timer E The transmit range indicator icon stays visible as long as the system is within operating range Icon The remote transmission indicator icon displays when the trans ceiver is transmitting a signal Icon The vibrate beep mode icon appears when the transceiver is set to vibrate mode O 2008 directed electronics all rights reserved 11 12 Icon The power saver mode can be turned on or off with the trans ceiver This icon displays the status Icon The remote start timer mode icon has no function The vehicle page mode icon displays when the alarm module is paging the transceiver The full trigger shock sensor icon indicates that t
10. described below gt Shock Sensor Light impacts to the vehicle will flash the vehicle lights and chirp the siren for a few seconds Remote Control Notification Ten quick beeps or vibra tions 2008 directed electronics all rights reserved gt Remote Control LCD The full trigger alert icon 28 will dimly illuminate for two seconds gt The transceiver will enter Page Recognition Mode and operate alarm page alerts note Icons 13 and 14 represent alarm system zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configurations section triggered response description A Triggered Response can be activated by any of the triggers listed below and consists of an alarm page along with the response described for each trigger The Triggered Response duration is 30 seconds gt Sensor Trigger Heavy impacts to the vehicle will instantly sound the siren and flash the lights for the programmed duration and report Zone 2 gt Door Trigger If a door is opened the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and report Zone 3 The three seconds allow the user time to disarm the system with a minimum of noise should a door be opened inadvertently while the system is armed gt Hood Trigger Opening the hood if connected will sound the siren flash the lights for the programmed duration and
11. microprocessor which monitors your vehicle and controls all system functions Fault Proof Starter Interrupt n automatic switch controlled by your system that prevents the vehicles starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet mode or if the starter interrupt switch itself fails Your system has feature ready circuitry for the starter interrupt however installation may require additional labor Input A physical connection to the system n input can be provided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights LCD 2 Way Remote A hand held transceiver which operates and monitors the various functions of your system LED red light mounted at a discretionary location inside the vehicle It is used to indicate the status of your system Shock Sensor This system has a dual zone shock sensor This sensor is mounted in the vehicle and designed to pick up impacts to the vehicle or glass O 2008 directed electronics all rights reserved 33 34 Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration Valet Button A small push button switch mounted at a discre tionary location inside the vehicle It is used to ove
12. understandings whether written or oral IN ANY EVENT DIRECTED ELECTRONICS IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or con struction This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover bat teries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis troubleshooting or rein stallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized dealer to obtain the service charge for your unit These systems are a deterrent against possible theft Directed Electronics is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorize any person to create for it any other obligation or liability in connection with this security system 2008 directed electronics all rights reserved i TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WAR RANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH THIS EXCLUSION IN
13. CLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WAR RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMTT ED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOW ING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con sequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state 2 500 Limited Theft Protection Guarantee Terms and Conditions Available only in the USA In the event that your vehicle is stolen and not recovered Directed Electronics will refund to the original purchaser of the Hornet system up to 2 500 of your insurance deductible This vehicle protection guar antee is valid only if 1 The installation was performed by an authorized Hornet dealer 2 The warranty registration card is completed and mailed within ten 10 days of purch
14. ase 3 At the time of the theft the system was fully functional and not in valet mode 4 The vehicle and its contents were insured at the time of the theft 5 The insurance company and the police have been notified and a written stolen vehicle report was issued by the Police Department 6 No less than thirty 30 days after the police report was issued you mail Directed Electronics clear photocopies of the following documents a Proof of Purchase OR provide the system model and name of the company that installed the system b The stolen vehicle report issued by the police c Insurance coverage documents for the stolen vehicle clearly showing all the details including the vehicle identification number and the insurance deductible amount d A dated declaration signed by you the owner of the vehicle attesting that the vehicle has been stolen for more than thirty 30 days and has not been recovered il 2008 directed electronics all rights reserved This vehicle theft protection is effective for one 1 year from the date of purchase and is limited to one claim This vehicle theft protection guarantee is valid only for the theft of the entire vehicle and specifically excludes any other considerations including but not limited to damage caused to the vehicle theft of parts contents or any other consequen tial damages Once Directed Electronics verifies that all the above listed terms and condi tions have been met a check for t
15. de This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the remote but all conve nience functions door locks trunk release etc will continue to work normally You can access Valet Mode either manually or with the remote To enter or exit Valet Mode manually N 1 Turn the ignition on SD 2 Turn the ignition off 3 Press and release the Valet No 9 RW 12 button within 10 seconds The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode O 2008 directed electronics all rights reserved 23 To enter or exit Valet Mode using the remote Steps 2 through 3 must be quickly and smoothly completed 1 Open any vehicle door The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode setting the clock To set the clock press and hold for five seconds the trans ceiver will chirp twice and the hour selection will start flashing Immediately press AUX to advance the hour selection or to reverse the hour selection Once the correct hour is displayed press again and the minute selection will start flashing Then press AUX to advance the minute selection or to reverse the minute selection Once the correct time is displayed simply stop pressing any buttons for 15 seconds and the transceiver will auto matically exit the clock mode n
16. ealer resulting in a unique easily identifiable siren sound The chirps can be either full volume or 6 decibels quieter than the full alarm blast 2008 directed electronics all rights reserved security amp convenience expansion Listed below are some of the many expansion options available Please consult your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery is dis connected Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the 508D radar sensor Your system can react to any intrusions into this field with the full triggered sequence Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Power Trunk Release The accessory output of the system can op erate a factory power release for the vehicles trunk or hatch Although the on board relay can control most power trunk re leases sometimes an optional relay is required If the factory r
17. een programmed off by the installer 2008 directed electronics all rights reserved disarming diagnostics Extra chirps that are heard when disarming the system are the Tamper Alert If four chirps are heard when disarming the system then the security system was triggered in your absence If five chirps are heard when disarming the system a zone was trig gered so many times that the Nuisance Protection Circuitry has bypassed that zone In either case the status LED will indicate which zone was involved see Table of Zones section The secu rity system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time that the ignition is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below Action Number of Chirps Description Arm 1 System armed Arm 1 3 second delay 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC active 2008 directed electronics all rights reserved 27 table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input Standard input assignments are listed in the following table along with spaces to write in any optional sensors or switches that have been installed
18. elease is not power activated Directed s 522T trunk release solenoid can often be added O 2008 directed electronics all rights reserved 31 Power Window Control Automatic power window control is pro vided with the 529T and 530T systems These can operate power windows and can roll them up automatically when the system is armed roll them down or both up and down Installation options 32 Installation options may require additional parts or labor Please consult your dealer Progressive Unlocking With electric power door locks the system can be configured so that when disarmed only the driver s door unlocks A second press of the disarm button within 15 seconds of disarming unlocks the remaining doors Horn Honk If connected the horn will sound if the alarm is either triggered by an intrusion or activated by Panic Mode In most vehicles this feature requires that an additional relay be installed Interior Light Illumination The interior domelight can be configured to illuminate for 30 seconds after the alarm is disarmed If the system is rearmed during that 30 second period the interior light illumination will terminate until the alarm is disarmed once again 2008 directed electronics all rights reserved glossary of terms Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the
19. guide 2008 directed electronics all rights reserved high security disarm This security system offers High Security Disarm High Security Disarm is a feature that makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds pressing Ey on the remote will stop the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visually checking the vehicle Pressing d after resetting the system will disarm the system pressing this button during the first six seconds of the triggered sequence will disarm the security system immediately The six second timer is provided for your convenience in case the system is accidentally triggered disarming without a remote If your remote is lost or damaged you can manually disarm your vehicle security system To disarm the system without a remote you must have the vehicle s ignition key and know where the Valet button is located Be sure to check with your installer at the time of installation for the location of the Valet button O 2008 directed electronics all rights reserved 21 To disarm the security system turn the ignition to the ON posi tion Press the Valet button within 15 seconds After five seconds the system will d
20. he insurance deductible up to 2 500 will be mailed within thirty 30 days Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile YNNNNNNNN Installation receipts 2008 directed electronics all rights reserved iil IV 2008 directed electronics all rights reserved UULE OF COTILETI limited lifetime consumer warranty i remote configurations ee de dd pes Gowns dao 3 O CONS AON oa a open at a do ee de 3 standard 4 button configuration both remotes 4 LCD 2 way remote addmonalcontrols 4440 m4 rss 6 What is mcluded ses odo serena sae ser creen es oo Esa aa 7 important information 7 ten ES A arias ranas a 8 VOUE cs uo 9 OO onue s ores otal eesawaes oa ee seen 9 Standard LCD 24way icon configuration 2 6 mn 10 LCD 2 way remote Operation 44e es bays AS 15 System sienal papino Meats si nc hada pareja be eu hnege e gato menue 16 USING VOD Syste 2246526 ct ease ceo eeareeeanes saneaeseranese tees nee 16 acts QING capa es aoe eee E eee Pees eee ee eee ee sees eyes
21. he shock sensor has been triggered by a hard shock The hood trunk open or trigger icon illuminates when the hood or trunk trigger has been activated or the hood or trunk is open and bypasses those zones until it is closed Icon The parking light icon will flash twice when armed or disarmed The icon also flashes during WarnAway The door open or trigger icon illuminates when the door trigger has been activated or the door is open and bypasses that zone until it is closed 2008 directed electronics all rights reserved CE leo The remote start icon has no function The Valet mode icon appears when the system is in Valet mode The battery level icon indicates the level of power remaining in the battery Icon The temperature controlled remote start icon has no function EW The silent arm disarm icon appears when the system has been armed or disarmed in the silent mode Icon The full trigger alert icon illuminates when the security system has been triggered by a heavy impact door trigger violation optional sensor violation or a hood trunk trigger Tal The arm icon appears when the vehicle is armed and locked The disarm icon appears when the vehicle is disarmed and unlocked Celsius Fahrenheit icon indicates the current mode of the displayed temperature either in Celsius or Fahrenheit O 2008 directed electronics all rights reserved 13 14 Standard LCD 2 way button functions Func
22. iliary output controls O 2008 directed electronics all rights reserved 5 AUX and pressed together control channel 4 output and optional auxiliary convenience or expansion function that you have added to your system The auxiliary output controls LCD 2 way remote additional controls note The controls listed below are applicable only to the LCD 2 way remote The LCD backlighting will turn on when pressed for less than one second when held for more than five seconds the trans ceiver will enter adjustment mode allowing the setting of the clock timer mode and audible melody selection For more infor mation please refer to the Function Button Configurations section of this guide and AUX Buttons The numeric display toggles between the time of the day and the alarm clock when these buttons are pressed simultaneously and Buttons Press these buttons simultaneously to activate the parking timer Each additional press will toggle through the available options 10 min 20 min 30 min 1 hour 1 5 hours 2 hours and off 6 O 2008 directed electronics all rights reserved Buttons When pressed simultaneously these buttons toggle between beep notification and vibrate notification and Buttons When pressed simultaneously these buttons activate battery saver mode which will drop power consumption on the transceiver battery to zero when the alarm is inactive or disarmed bat is included Contro
23. isarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of Valet Button silent mode 22 To temporarily turn off the arm or disarm chirps use Silent Mode Simply press f UK for less than one second before arming or disarming and the confirmation chirp s will be elim inated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The Warn Away response to lighter impacts is bypassed if the system is armed using Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering by heavy impacts Only the Warn Away response is bypassed 2008 directed electronics all rights reserved panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your remote Just press Ok for 1 5 seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press The LCD 2 way remote will beep or vibrate continuously when the system enters panic mode The 2 way remote will not generate a page notification when panic mode is exited valet mode You can prevent your security system from automatically arming and triggering by using Valet Mo
24. l be cleared note The transceiver buttons will not send a command to the system until the alarm page is cleared 2008 directed electronics all rights reserved important Due to the complexity of this system instal lation of this product must only be performed by an authorized Directed dealer active arming You can arm the system by pressing second When the system arms you will hear a short siren sound of your remote for one or chirp and see the parking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the status LED will flash approximately once per second indicating that the system is actively protecting your vehicle If you hear a second chirp after arming and note that the status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification which indicates that a security sensor or switch has been bypassed and the system is not monitoring that area zone of the vehicle passive arming The system can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the last protected entry has been closed e g the system detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming co
25. l module 544N transceiver antenna One 4 button remote One 2 way LCD remote Impact sensor on board control module High powered siren Fault proof starter interrupt relay on board control module Status LED indicator light Push button Valet button VV Y Y Y VV VY VY Y Your warranty registration 2008 directed electronics all rights reserved 7 important information Congratulations on the purchase of your state of the art vehicle security system This system has been designed to provide years of trouble free operation By carefully reading this guide prior to using your system you will maximize the use of this product and 1ts features By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing our web site at www directed com system maintenance The system requires no specific maintenance other than battery replacement for the remotes LCD 2 Way Remote Battery Replacement The 2 way remote is powered by a 1 5V AAA battery The Battery Level indicator has three level indicators that serve as a visual indication of battery charge When the battery reaches a low charge level that requires replacement the transceiver will generate a single notification chirp and the Battery Level indi cator will flash continuously DDD FULL REPLACE EMPTY 8
26. o Function 12 Vehicle Page Mode Indicator 13 Full Trigger Shock Sensor Indicator 14 Hood Trunk Open or Trigger Indicator 15 Parking Light Indicator 16 Door Open or Trigger Indicator 17 Arm Lock Button 18 Disarm Unlock Button 19 Remote Start Indicator 20 Hood Trunk Open or Trigger Indicator 21 Remote Start Button 22 Valet Mode Indicator 23 Remote Start Safety Shutdown Indicator 24 Battery Level Indicator 25 Auxiliary Button 26 Temperature Controlled Remote Start Indicator 27 Silent Arm Disarm Mode Indicator 28 Full Trigger Alert Indicator 29 Arm Disarm Indicator 30 Function Button 31 Celsius Fahrenheit Indicator 2008 directed electronics all rights reserved standard 4 button configuration both remotes controls the Arm and Panic On Off function The arming is controlled by pressing this button The panic alarm is triggered by pressing and holding this button Press again to cancel the panic alarm Silent mode works by pressing this button for less than one second before arming or disarming And optional auxiliary func tion such as trunk release can be controlled by pressing and holding this button for 1 5 seconds controls the Panic function by pressing and holding this button for 1 5 seconds The auxiliary output controls A a and Y pressed together control channel 3 output and optional auxiliary convenience or expansion function that you have added to your system The aux
27. rride the starter interrupt when a remote is lost or damaged or to enter or exit Valet Mode Warning Zone Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 2008 directed electronics all rights reserved Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet QUICK REFERENCE GUIDE Arming M lo arm press A When the system arms you will hear a short chirp and the parking lights will flash once Disarming o M To disarm press EN You will hear two chirps and the parking lights will flash twice High security disarm B M For high security disarm press EN on your remote and the siren will stop sounding To completely disarm the security system press again and the system will chirp 4 or 5 times reporting the trigger Disarming without a remote M Turn on the ignition Press the Valet button within 15 seconds The system should now disarm If it does not you may have waited too long so turn the ignition off and on and try again Silent Mode M Pressing l briefly before arming or disarming will eliminate the confirma tion chirp s for that one operation only
28. tion Lamp On 10 sec Power Saver Mode Beep Vibrate Mode Time Adjust Mode hour Time Adjust Mode min Alarm Clock Set Mode hour Alarm Clock Set Mode min Alarm Clock Music or Power on Music Selection Alarm Clock Adjust Mode on off Timer Count Down Adjust Mode hour Timer Count Down Adjust Mode min Timer Count Down Ending Melody Selection 1 RS Timer Count Down Mode on off where applicable Button OnE Od for 5 Seconds ne ie 3 Times 4 Times 5 limes 6 Times 7 Times 8 Times 9 Times Audible Icon Indication ao Melody 0 4 Vibrations 1 Beep 8 88 2 Beeps 8 88 5 Selections 1 2 3 4 5 5 Selections 1 2 3 4 5 2008 directed electronics all rights reserved Remote Start On 10 times 5 Selections Melody Selection 2 where applicable 1 2 3 4 5 10 Min Parking 1 Time Melody Count Down Mode 20 Min Parking 2 Times Melody Count Down Mode 30 Min Parking 3 Times Melody Count Down Mode 60 Min Parking 4 Times Melody Count Down Mode 90 Min Parking i 5 Times Melody Count Down Mode 120 Min Parking 6 Times Melody Count Down Mode Parking Count Down 7 Times Melody Off Mode Alarm Clock Mode E Melody OnOm Celsius Fahrenheit AUX or Melody Select Mode This function will operate in the disarmed state only The button will advance the selection upward
29. uisance prevention circuitry 24 Your system has Directed s Nuisance Prevention Circuitry NPC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc 2008 directed electronics all rights reserved Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the security system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continually being triggered will remain bypassed The vehicle doors are protected by NPC differently If your security system is triggered by an open door for three full 30 second cycles one and one half minutes the system will bypass the doors until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working If five chirps are heard when disarming
30. untdown the status LED will flash twice as fast as it does when the system is armed If the system is programmed for Passive Arming care must be taken to prevent the keys from being locked in the vehicle O 2008 directed electronics all rights reserved 17 note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm Additionally each time a protected entry is opened triggered during the arming count down the 30 second countdown starts over When armed your vehicle is protected as follows gt gt Light impacts trigger the Warn Away signal When triggered the siren chirps and the parking lights flash for a few seconds Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for 30 seconds If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your remote if you inadvertently open the door while the system is armed Turning on the ignition key will trip the same progressive re sponse as opening a door The starter kill prevents the vehicle s starter from cranking warn away response description A Warn Away Response consists of an alarm page along with the 18 responses
31. ya 17 PISE ona ros posada anta de ica 17 warn away response description 18 triggered response description 322 2e cs de der ao 19 A eo aie 2 20 WenS COn AAE paea ea EE E A R E E a p 20 Aa w NOUTA TEMOS secese a ao E ne 21 E EE EE EE E EE ET EE E T TE 22 DO aaa 22 RE oe eeG a etee e 23 A CO ere 24 nuisance prevention cirCUITIY 24 CD OS ESS 25 APMIS MACHOSHICS 4a aconk ra aan 26 CSS danos reves asepsia apta e sp lies e eee an 26 A CRD ed ae de de be a eo oo 27 FDIC OL AO en 27 code HOPPING ee os ae a cn 28 High D 6 LOS 010 copar EEEO EEEE dano ees seso pao esupa E 29 et EA o 29 PIOCAMMING ODHOHS en sdr eurrera OE to opa rocade 29 security amp convenience expansions s 30 installation OPHONS senior ea obs ae sena e ee dada dto ea 32 SlOssaty OF Gl years eames ang sae Rape Roe aras 22 2008 directed electronics all rights reserved 2008 directed electronics all rights reserved rem nfiquration LCD 2 way configuration O 2008 directed electronics all rights reserved pi Vehicle Interior Temperature Indicator Numeric Display AM PM Indicator Alarm Clock Mode Indicator Timer Function Indicator Transmit Range Indicator Transmission Indication Vibrate Beep Mode Indicator ON W Hs OO IN O0 IN 9 Power Saver Mode Indicator 10 Remote Start Timer Mode Indicator 11 N
Download Pdf Manuals
Related Search