Avaya V1.0) User's Manual
Contents
1. Read Me First This document supplements or corrects all other documentation you receive with the BayStack ARN router hardware and software Release Notes This section supplements the Release Notes for Router Software Version 11 00 Revision 4n and the Release Notes for Site Manager Software Version 5 00 Revision 4n Terminal Console Interface Table 1 lists the correct pin signals for the ARN Console port Table C 12 in Installing and Operating BayStack ARN Routers lists incorrect pin signals Table 1 Terminal Console Port DB 9 Pin Assignments Pin Assignment Pin No Signal Name Direction 1 Not used From terminal 2 Transmit data TXD To terminal Pin 1 3 Receive data RXD From terminal As 4 Not used From terminal Z vi 5 Ground N A 6 DTR To terminal Fina 7 Not used From terminal 8 Not used To terminal 9 Not used N A 114593 A Rev A 1 Read Me First Router Software 11 00 Rev 4n and Site Manager 5 00 Rev 4n Note The ARN Console port does not support a modem You must attach an external modem to the ARN Modem port or use the optional integrated V 34 console modem Integrated V 34 Console Modem Support The V 34 console modem adapter module e Supports only Raise DTR e Does not support asynchronous PPP connectivity e Must be configured as Monitor and set to originate calls for bandwidth on demand e Must be configured as Dial Master and set2. able the circuit before you delete it you can then re create the circuit without getting a fault condition Anomaly You cannot delete an ISDN demand circuit from the router when a call is active Number 27800 Description Attempting to delete a demand circuit when a call is active causes a fault condition This occurs on both the AN and ARN platforms Workaround Disable the circuit before you delete it Anomaly In the V 34 modem AT command string Site Manager misinterprets LO as OFF Number 27802 Description If you add LO to the user defined AT command string Configuration Manager gt Edit Modem gt Expert Config ON then enter a string in Modem Config String Site Manager interprets the code as OFF The LO code should indicate Low volume Workaround Do not include the LO command in an AT command string Anomaly ARN V 34 modem answer string is not set on the first attempt Number 27803 Description The first time you set the V 34 modem to answer calls Configuration Manager gt Edit Modem gt Originate Answer Answer the parameter resets to Originate after you click on OK Workaround To set the V 34 modem to answer calls configure the Answer parameter twice Configuration Manager gt Edit Modem gt Originate Answer then repeat Anomaly Modifying Site Manager Console parameters does not restart the Technician Interface Number 27807 Description Some of the configurable console parameters for example
3. the more Enable and TI History Depth parameters do not restart the Technician Interface Even though the MIB values change these new values do not take effect until the Technician Interface restarts Workaround Restart the Technician Interface by changing the Technician Interface prompt that is modifying the Prompt parameter or by logging out and then in again to the Technician 114593 A Rev A Read Me First Router Software 11 00 Rev 4n and Site Manager 5 00 Rev 4n Interface from a direct console connection Anomaly Netboot works on DSU CSU only when configured for the default 56 Kb s DDS lines Number 27815 Description Netboot fails over a DSU CSU interface configured for Clear Channel 64 Kb s lines Configuration Manager gt Edit DSU CSU gt Option Mode CC 64KBPS Anomaly The ARN initiates dial service calls on an internal console modem set to Answer Only Number 27819 Description On an ARN with both an internal console modem and an external modem the router initiates calls on the internal rather than the external modem even though the internal modem is set to Answer Only The call attempt fails and the router eventually initiates calling on the correct modem but only after three retries Workaround Ensure that the internal console modem is not used by setting its wfSyncPriority to a high number for example 99 Anomaly When configuring a second circuit using the inst_arn bat script selec
4. ting static route from the IP Routing Protocol Configuration menu causes a fault condition Number 27829 Description When you are configuring a second circuit using the inst_arn bat script and you select static route option 3 from the IP Routing Protocol Configuration menu the following error message appears Variable Undefined Variable dlci_mgt The inst_arn bat script returns you to the IP Static Route to Site Manager Configuration window The script continues to loop in this manner without allowing you to configure the second circuit with IP static routes Workaround Do not add a second circuit that contains IP static routes 114593 A Rev A
5. to originate calls for Dial Backup e Does not originate and answer calls simultaneously therefore must be set to originate when BOD is configured as Monitor or when Dial Backup is configured as Master and must be set to answer when BOD is Non Monitor or Dial Backup is Slave Netbooting over a DSU CSU Interface The ARN supports Netbooting over the DSU CSU interface only for the default configuration 56 Kb s DDS lines You cannot netboot over a 64 Kb s DSU CSU interface ARN Platform Known Anomalies This section supplements the Known Anomalies Router Software 11 00 Revision 4n and Site Manager 5 00 Revision 4n Anomaly Site Manager allows setting Modem Enable on the ARN console port but the port does not support a modem Number 27605 Description The Modem Enable parameter should always be disabled for editing However if you edit Serial Port 1 and then Serial Port 2 the Modem Enable option is not dimmed when returning to Serial Port 1 Workaround Do not set the Site Manager Modem Enable parameter to Enable and do not set wfSerialPortEntry 12 1 to 1 from the Technician Interface 2 114593 A Rev A Read Me First Anomaly Deleting and then re creating a synchronous circuit in dynamic mode causes a fault condition Number 27799 Description Using dynamic mode to delete a synchronous circuit and then re creating the same circuit in the router configuration causes a fault condition Workaround Dis
Download Pdf Manuals
Related Search