Avaya BCM Imaging Tool User Guide
Contents
1. keyboard port monitor port USB ports Connecting a CD ROM drive to the Business Communications Manager To use the BCM Imaging Tool you must connect a CD ROM drive to the Business Communications Manager The Business Communications Manager system uses this CD ROM drive as the boot device when you start the BCM Imaging Tool and to load the information from the BCM Image CDs If your Business Communications Manager system is a BCM 200 or a BCM 400 you can use a USB CD ROM drive or an IDE CD ROM drive The advantage of the USB CD ROM drive is that it is quicker and easier to install on the Business Communications Manager The advantage of the IDE CD ROM drive is that it loads the BCM Image much quicker Note To use a USB CD ROM drive with a BCM 200 or a BCM 400 your Business Communications Manager system must be using software version 3 5 or greater m Tip To get the benefits of easier CD ROM drive installation and faster loading of the BCM Image use a USB CD ROM drive and load the BCM Image from a shared network drive If your Business Communications Manager system is a BCM 1000 you must use an IDE CD ROM drive P0609711 01 01 Connecting to the Business Communications Manager 17 Connecting a USB CD ROM drive to a BCM 200 or BCM 400 1 2 Place the CD ROM drive next to the Business Communications Manager Connect the USB cable from the CD ROM drive to one of the USB ports on the front of the BCM2. refer to Performing a system startup and warm reset in the Business Communications Manager Management User Guide When you are loading the BCM Image you can load one of the following software versions as well as any software version greater than BCM 3 6 e BCM3 0 e BCM3 0 1 e BCM3 5 e BCM3 6 You can load the BCM Image from the CD ROM drive connected to the Business Communications Manager from a shared network drive or from a shared CD ROM drive Note If you want to use the Backup and Restore Utility BRU to restore the system programming you must load the BCM Image for the same software version that the backup was made with 1 e the same version that is currently on your Business Communications Manager Nortel Networks recommends that you load the same software version that is currently on the Business Communications Manager system If you would like to change the software version use the Business Communications Manager Upgrade Kit after you have finished loading the BCM Image The Upgrade Kit includes additional updates that are not loaded when you use the BCM Imaging Tool For example the Upgrade Kit for software version 3 5 includes a BIOS update that enables USB support If you used the BCM Imaging Tool to change the software version from 3 01 to 3 5 the Business Communications Manager system would not get the update required to support USB CD ROM drives BCM Imaging Tool User Guide 20 Loading the BCM Image Load
3. 18 If the network uses a WINS server enter the IP address of the WINS server If the network does not use a WINS server go to the next step BCM Imaging Tool User Guide 26 Loading the BCM Image 19 20 21 22 23 24 25 26 Use the Tab key to highlight the OK button and press the Enter key or press Alt Q The Windows Networking Logon screen appears Windows Networking Logon Domain JORKGROUP Userid Password Ok Cancel Enter the name of the Domain in which the computer with the shared drive is located and press the Tab key If you are not using domain names on your network enter the Machine Name of the computer with the shared drive or the name of the Workgroup to which the computer belongs and press the Tab key The Userid field is highlighted Enter the User name required to access the shared drive and press the Tab key The Password field is highlighted Enter the Password required to access the shared drive Use the Tab key to highlight the OK button and press the Enter key or press Alt Q The Image Storage screen appears Image Storage Enter location of network share Share SERVER SHARES Ok Cancel Enter the pathname of the shared drive for example rdoe 3 BIT35 Note You cannot use an IP address in the pathname you enter to specify the location of the shared drive You must always use the server name Use the Tab key to highlight the OK button and press the Enter key o
4. 200 or BCM 400 For the location of the USB ports refer to Figure 5 for the BCM 200 or Figure 6 for the BCM 400 Connect the power cable to the CD ROM drive Connecting an IDE CD ROM drive to a BCM 200 or BCM 400 1 Make sure that power is disconnected from the BCM 200 or BCM 400 If it is not refer to Disconnecting power from the Business Communications Manager on page 13 If required for accessibility remove the BCM 200 or BCM 400 from the rack or the wall and place it on a flat clean and static free surface Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface Remove the top cover screws located at the rear of the BCM 200 or BCM 400 Place the screws in a Safe location Lift the back of the cover and slide it rear ward until it disengages from the BCM 200 or BCM 400 Lift the top cover up and away from the BCM 200 or BCM 400 Place the cover in a safe location Place the CD ROM drive in the BCM 200 or BCM 400 Make sure you leave room in front of the CD ROM drive to allow inserting the CDs Connect the available connector on the IDE cable to the CD ROM drive Connect an available power connector to the back of the CD ROM drive Connecting an IDE CD ROM drive to a BCM 1000 1 Make sure that power is disconnected from the BCM 1000 If it is not refer to Disconnecting power from the Business Communications Manager on page 13 Attach one end of a grounding str
5. BCM Imaging Tool P0609711 01 01 Returning the Business Communications Manager to normal operation 29 Returning the Business Communications Manager to normal operation After you have finished applying a BCM Image you must return the Business Communications Manager system to its normal operating configuration Figure 7 shows the high level steps required to return the Business Communications Manager to its normal configuration Figure 7 Overview of returning the Business Communications Manager to its normal configuration Remove the CD ROM drive Disconnect the monitor and keyboard Restart the Business Communications Manager Initialize the hard disk Restore the system programming BCM Imaging Tool User Guide 30 Returning the Business Communications Manager to normal operation Removing a USB CD ROM drive from a BCM 200 or BCM 400 Turn off the CD ROM drive Disconnect the power cable from the CD ROM drive Disconnect the USB cable from the CD ROM drive and the Business Communications Manager Removing an IDE CD ROM drive from a BCM 200 or BCM 400 N Oo OF fF Q co Disconnect the power cable from the BCM 200 or BCM 400 Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface Disconnect the IDE ribbon cable from the CD ROM drive Disconnect the power connector from the CD ROM drive Remove the CD ROM drive from the BCM 200 or BCM 400 Set the top cover on the BCM 200 o
6. CALA Caribbean amp Latin America 0 0 0 ccc eens 9 PP ha nna PACC 656k he ewe oo he see eee ee BEERS A AAE eRe se eee 9 Chapter 1 Using BCM Imaging OO risubeecchepweeseeugeeieeeseesecepweasen ewes 11 JUG ban cen ge aan oes a eed wees eee sune hee eee a haeetneesceeaubeseet 11 FSGS a i hr dA SOHO AOA ORE CELA EERD HRKAKS SAD ERS AE RRS R KEKE 12 Compatible USB CD ROM drives 0 0 00 ce eee 12 Connecting to the Business Communications Manager 0000e eee eee 13 Disconnecting power from the Business Communications Manager 13 Connecting a monitor and keyboard 0 ccc eee 14 Connecting a monitor and keyboard to a BCM 1000 0 5 14 Connecting a monitor and keyboard to a BCM 200 or BCM 400 14 Connecting a CD ROM drive to the Business Communications Manager 16 Connecting a USB CD ROM drive toa BCM 200 or BCM 400 17 Connecting an IDE CD ROM drive toa BCM 200 or BCM 400 17 Connecting an IDE CD ROM drive toa BCM 1000 00 0 ee 17 Connecting a network cable to the Business Communications Manager 18 Doane The BOM We a as eae RO ERE REE eRe Ee ee ERO 19 Loading the BCM Image from a CD ROM drive 0000 cece eee 20 Loading the BCM Image from a network drive 0 0 ee ee 23 Preparing a shared network drive 0 ccc cee ee eee eee 28 Configuring your computer to co
7. DOSs 6 22 startup Menu l External USB CD ROM Drive Internal IDE CD ROM Drive Enter a choice 1 Select the CD ROM drive in which you installed the BCM Imaging Tool CD and press the Enter key The License Agreement screen appears Read the entire License Agreement and press the Enter key To scroll the License Agreement up or down use the Page Up Page Down or arrow keys If you want to accept the License Agreement and use the BCM Imaging Tool use the Tab key to highlight the Accept button and press the Enter key The Unlock screen appears Note If you do not want to accept the License Agreement use the Tab key to highlight the Decline button and press the Enter key The BCM Imaging Tool exits Unlock Unique ID 6H AW CEC 56 53 CE Access Code Ok Cancel Enter the Access Code for this Business Communications Manager system If you do not have the Access Code for this Business Communications Manager system contact your Nortel Networks support personnel and request the Access Code for this system Provide the support personnel with the Unique ID that is shown on Unlock screen of the BCM Imaging Tool Note An Access Code works for only one Business Communications Manager system You cannot use an Access Code from another Business Communications Manager system Use the Tab key to highlight the OK button and press the Enter key or press Alt Q The Select Media Location screen appears P0609711 01 01 Loadi
8. the BCM Imaging Tool Figure 1 Overview of using the BCM Imaging Tool Connect the equipment to the Business Communications Manager Load the image Return the Business Communications Manager to normal operation BCM Imaging Tool User Guide 12 Overview Prerequisites To use the BCM Imaging Tool you must be at the same site as the Business Communications Manager system You also need the following e aBCM Imaging Tool CD This CD contains the BCM Imaging Tool application and the system files required by the Business Communications Manager system to boot from this CD e aset of BCM Image CDs This set of CDs contains the files that are being loaded onto the Business Communications Manager system There is one set of BCM Image CDs for each version of Business Communications Manager software that you can load Make sure you have the correct set of CDs for the Business Communications Manager software version you want to load for example BCM 3 6 e an access code for the Business Communications Manager system you are working on e akeyboard e amonitor e a USB or IDE CD ROM drive e access to a network drive optional Note The BCM Imaging Tool does not work on Business Communications Manager __ systems with an 8 GB hard drive Note To use a USB CD ROM drive your Business Communications Manager system must be a BCM 200 or BCM 400 As well your system have been purchased with software version 3 5 or greater or up
9. to continue 16 Use the Tab key to highlight the Yes button and press the Enter key or press Alt Y 17 When the BCM Imaging Tool has finished loading the BCM Image the BCM Imaging Completed screen appears You can now return the Business Communications Manager system to its normal operating configuration using the steps in Returning the Business Communications Manager to normal operation on page 29 ECM Imaging Completed The ECH has been successfully imaged You can now restart the system Please disconnect any device used during the BIT process P0609711 01 01 Loading the BCM Image 23 Loading the BCM Image from a network drive To load the BCM Image from a network drive you must have a CD ROM drive connected to the Business Communications Manager system You must also have one of the following network connections e A computer connected to the Business Communications Manager system using an Ethernet crossover cable or two Ethernet cables and a local hub or switch For information about the network settings required for this connection refer to Configuring your computer to connect using an Ethernet crossover cable on page 28 e A computer on the network that you can access from the Business Communications Manager system Note The computer that has the network drive you want to use must be using Windows NT Windows 2000 or Windows XP The BCM Imaging Tool does not support Windows 95 Windows 98 or Windows Me T
10. 19 Initializing hard disk 33 IP address 25 K Keyboard connecting to BCM 1000 14 connecting to BCM 200 14 connecting to BCM 400 14 disconnecting from BCM 1000 31 disconnecting from BCM 200 31 disconnecting from BCM 400 31 Keycodes 19 34 L LAN card 18 License Agreement 21 24 Loading BCM Image 19 20 23 Lost information 19 M Monitor connecting to BCM 1000 14 connecting to BCM 200 14 connecting to BCM 400 14 disconnecting from BCM 1000 31 disconnecting from BCM 200 31 disconnecting from BCM 400 31 P0609711 01 01 N Network cable connecting 18 Network drive loading BCM Image 23 O Overview BCM Imaging Tool 11 connecting equipment 13 returning Business Communications Manager to normal operation 29 P Ports location on BCM 1000 14 location on BCM 200 15 location on BCM 400 16 Power disconnecting 13 Prerequisites 12 Programming restoring 34 Publications related 8 R Removing IDE CD ROM drive from BCM 1000 30 IDE CD ROM drive from BCM 200 30 IDE CD ROM drive from BCM 400 30 USB CD ROM drive from BCM 200 30 USB CD ROM drive from BCM 400 30 Requirements shared drive 23 USB CD ROM 16 Restarting Business Communications Manager 33 Restoring programming 34 Restrictions hard drive size 12 S Shared drive requirements 23 Software keycodes 34 Software versions supported 19 Static IP 25 Subnet mask 25 Supported software version 19 Symbols documentation 7 T Tele
11. Part No P0609711 01 01 May 4 2004 Business Communications Manager BCM Imaging Tool User Guide NORTEL NETWORKS Copyright 2004 Nortel Networks All rights reserved May 4 2004 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Nortel Networks NA Inc Trademarks NORTEL NETWORKS is a trademark of Nortel Networks Microsoft MS MS DOS Windows and Windows NT are registered trademarks of Microsoft Corporation All other trademarks and registered trademarks are the property of their respective owners P0609711 01 01 Contents gi ee E eee ee ee ee ee ee er ee ee ee 5 Pe ie ee bn OOS eS ee ee on ee ET E ea eee 7 cee ee cae cm lggig ae ee ee ee ee ee Se 7 TORSION ooh dade ares 655 oS so Oe hese meee hse eee eee be eddies 7 P ee ee re a Se rer ee ee ee a 8 RGAE PUDIICATONS 225 e456 cc0h060455 65 20 nheee seed stews ncednntetesaudgensasd 8 Bogie ws ee ee ee ee ee ee ee ee ee ee ee ee ee 9 USA and Canada een cee eesa ae deeenah eeweeeee sede dceeretuessreroansas4 9 Presales Support CSAN 0 0 0 eee eee eee 9 EMEA Europe Middle East Africa 0 00 eae 9
12. ada Authorized Distributors ITAS Technical Support Telephone 1 800 4NORTEL 1 800 466 7835 If you already have a PIN Code you can enter Express Routing Code ERC 196 If you do not yet have a PIN Code or for general questions and first line support you can enter ERC 338 Website http www nortelnetworks com support Presales Support CSAN Telephone 1 800 4NORTEL 1 800 466 7835 Use Express Routing Code ERC 1063 EMEA Europe Middle East Africa Technical Support CTAS Telephone European Freephone 00800 800 89009 European Alternative United Kingdom 44 0 870 907 9009 Africa 27 11 808 4000 Israel 800 945 9779 Note Calls are not free from all countries in Europe Middle East or Africa Fax 44 191 555 7980 email emeahelp nortelnetworks com CALA Caribbean amp Latin America Technical Support CTAS Telephone 1 954 858 7777 email csrmgmt nortelnetworks com APAC Asia Pacific Technical Support CTAS Telephone 61 388664627 Fax 61 388664644 email asia_support nortelnetworks com BCM Imaging Tool User Guide 10 How to get help P0609711 01 01 11 Chapter 1 Using BCM Imaging Tool The BCM Imaging Tool is a software application you use if the contents of the Business Communications Manager hard drive becomes corrupted With the BCM Imaging Tool you can change the contents of the hard drive back to factory default Overview Figure 1 shows an overview of using
13. ap to your wrist and the other end to a grounded metal surface If required for accessibility remove the BCM 1000 from the rack or the wall and place it on a flat clean and static free surface Remove the two screws from the cover at the back of the BCM 1000 Lift the back of the cover and slide it back and up Place the CD ROM drive in the BCM 1000 Make sure you leave room in front of the CD ROM drive to allow inserting the CDs Connect the available connector on the IDE cable to the CD ROM drive Connect an available power connector to the back of the CD ROM drive BCM Imaging Tool User Guide 18 Connecting to the Business Communications Manager Connecting a network cable to the Business Communications Manager When you are loading a BCM Image to the hard drive you can load the BCM Image from the CD ROM drive connected to the Business Communications Manager system a shared network drive or a shared CD ROM drive To use a shared network drive or a shared CD ROM drive you must connect the Business Communications Manager to a computer on the network or to a local computer To connect the Business Communications Manager to a computer on the network use a standard Ethernet cable to connect the LAN card on the Business Communications Manager to a port of a switch or router on the network To connect the Business Communications Manager to a local computer e Use an Ethernet cross over cable to connect the LAN card on the Busines
14. ata and telephony connections from the front of the Business Communications Manager 3 Disconnect the Business Communications Manager from the AC power outlet BCM Imaging Tool User Guide 14 Connecting to the Business Communications Manager Connecting a monitor and keyboard To use the BCM Imaging Tool you must connect a monitor and keyboard to the Business Communications Manager The monitor and keyboard are connected to ports on the front of the Business Communications Manager Connecting a monitor and keyboard to a BCM 1000 1 Open the door on the bezel to reveal the ports 2 Connect the monitor and keyboard to the appropriate port Refer to Figure 3 for the location of the ports Figure 3 Location of the ports on a BCM 1000 O O NORE WoRKsL_ id NETWORKS cooo 8 3 Po L o o0 O 0O 0O C Business Communications Manager Q mm Q ci oCo oC Jo O O O O O O OO O00 O O keyboard port monitor port Connecting a monitor and keyboard to a BCM 200 or BCM 400 1 Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface Remove the base function tray latch screws Place the screws in a safe location Move the base function tray latches to the unlocked position See Figure 4 Grasp the base function tray latches and partially remove the base function tray from the platform base chassis Do not exert force on the DS30 ribbon cables or connectors Unfasten the b
15. cting 17 USB CD ROM drive removing 30 BCM Image loading 19 loading from CD ROM drive 20 loading from network drive 23 BCM Image CDs 12 BCM Imaging Tool CD 12 BCM Imaging Tool overview 11 BCM software versions supported 19 BRU 34 Business Communications Manager restarting 33 returning to normal operation 29 37 software version supported 19 C Caution symbol 7 CD ROM drive connecting 16 loading BCM image from 20 Connecting CD ROM drive 16 equipment to Business Communications Manager 13 keyboard to BCM 1000 14 keyboard to BCM 200 14 keyboard to BCM 400 14 monitor to BCM 1000 14 monitor to BCM 200 14 monitor to BCM 400 14 network cable 18 overview of equipment 13 Conventions and symbols 7 conventions text 7 D Danger symbol 7 Data connections connecting 33 disconnecting 13 DHCP 25 Disconnecting data connections 13 keyboard from BCM 1000 31 keyboard from BCM 200 31 keyboard from BCM 400 31 monitor from BCM 1000 31 monitor from BCM 200 31 monitor from BCM 400 31 power 13 telephony connections 13 Domain 26 DS30 cables 14 32 E Ethernet cable 18 23 Expansion unit 33 BCM Imaging Tool User Guide 38 Index G Gateway 25 H Hard disk initializing 33 Hard drive size restriction 12 IDE CD ROM drive connecting to BCM 1000 17 connecting to BCM 200 17 connecting to BCM 400 17 removing from BCM 1000 30 removing from BCM 200 30 removing from BCM 400 30 Information lost
16. cting power from the Business Communications Manager and then reconnecting power The Startup Menu appears Ma DOSs 6 22 startup Menu l External USB CD ROM Drive Internal IDE CD ROM Drive Enter a choice 1 6 Select the CD ROM drive in which you installed the BCM Imaging Tool CD and press the Enter key The License Agreement screen appears 7 Read the entire License Agreement and press the Enter key To scroll the License Agreement up or down use the Page Up Page Down or arrow keys P0609711 01 01 8 9 Loading the BCM Image 21 If you want to accept the License Agreement and use the BCM Imaging Tool use the Tab key to highlight the Accept button and press the Enter key The Unlock screen appears Note If you do not want to accept the License Agreement use the Tab key to highlight the Decline button and press the Enter key The BCM Imaging Tool exits Unlock Unique ID HA AH CC 56 53 CE Access Code Ok Cancel Enter the Access Code for this Business Communications Manager system If you do not have the Access Code for this Business Communications Manager system contact your Nortel Networks support personnel and request the Access Code for this system Provide the support personnel with the Unique ID that is shown on Unlock screen of the BCM Imaging Tool system You cannot use an Access Code from another Business Communications Manager system Note An Access Code works for only one Business Commun
17. ees 15 Figure6 Location of the ports on a BCM 400 0 cece eee ees 16 Figure 7 Overview of returning the Business Communications Manager to its normal configuration 29 Figure 8 Install the base function tray bezel 0 0 cc eee 31 Figure 9 Install the base function tray 1 0 0 ccc et ee ens 32 BCM Imaging Tool User Guide 6 Figures P0609711 01 01 Preface The BCM Imaging Tool is a tool intended to correct configuration or hard disk content problems that cannot be solved using other methods The BCM Imaging Tool allows you to change the contents of the Business Communications Manager hard drive back to its factory settings This guide provides information about how to use the BCM Imaging Tool Symbols used in this guide This guide uses symbols to draw your attention to important information The following symbols appear in this guide Caution Caution Symbol Alerts you to conditions where you can damage the equipment Danger Electrical Shock Hazard Symbol Alerts you to conditions where you can get an electrical shock Warning Warning Symbol Alerts you to conditions where you can cause the system to fail or work improperly gt gt Note Note Symbol A Note alerts you to important information Security note This symbol indicates a point of system security where a default should be changed or where the administrator needs to make a decision about the level of security required fo
18. ezel screws from the base function tray face Place the screws in a safe location Pull and tip the bezel away from the base function tray until the bezel clips are clear of the base function tray chassis Move the bezel in a downward direction between the base function tray latches Place the bezel in a safe location P0609711 01 01 Connecting to the Business Communications Manager 15 Figure 4 Remove the base function tray bezel Tip bezel away from base function tray Unfasten Bezel screws iD ve G Unhook bezel clips Move bezel downward from base function and between latches tray chassis 7 Push the base function tray completely into the chassis Be careful not to crimp the DS30 ribbon cables Move the base function tray latches to the locked position Connect the monitor and keyboard to the appropriate ports Refer to Figure 5 or Figure 6 for the locations of these ports Figure 5 Location of the ports on a BCM 200 me DSOS O E E L oN HONN ce a at keyboard port monitor port USB ports BCM Imaging Tool User Guide 16 Connecting to the Business Communications Manager Figure 6 Location of the ports on a BCM 400 VOUTUCUT mH Oo O DE O O all a UIUI c2 scm w m
19. graded to software version 3 5 or greater using the Business Communications Manager Upgrade Kit Compatible USB CD ROM drives The BCM Imaging Tool works with USB CD ROM drives that support the El Torito Bootable CD ROM Format Specification The following USB CD ROM drives have been tested by Nortel Networks and are known to be compatible with the BCM Imaging Tool e PlexWriter 24 10 24U Hi Speed USB external CD RW drive e LG Portable USB 2 0 CD RW DVD ROM Drive e Jomega CD RW 52x24x52x USB 2 0 Drive e Universal BUSlink USB 2 0 SLIM 24X CD ROM PC e Addronics 52x32x32x Other USB CD ROM drives may be compatible but they have not been tested by Nortel Networks for compatibility P0609711 01 01 Connecting to the Business Communications Manager 13 Connecting to the Business Communications Manager To use the BCM Imaging Tool you must connect a monitor keyboard and CD ROM drive to the Business Communications Manager Figure 2 shows the high level steps required to connect this equipment to the Business Communications Manager Figure 2 Overview of connecting the required equipment to the Business Communications Manager Disconnect power Connect the monitor and keyboard Connect the CD ROM drive Connect a network cable if applicable Disconnecting power from the Business Communications Manager 1 If you still have access to the Unified Manager shut down the system using the Shutdown command 2 Remove all of the d
20. he network share can be a shared folder on a hard drive or a shared CD ROM drive If you are using a shared folder on a hard drive you must load the BCM Imaging Tool and the BCM Images onto the shared folder before you start the BCM Imaging Tool For information about loading these files onto a shared folder refer to Preparing a shared network drive on page 28 If you are using a shared CD ROM drive load the BCM Image CDs into the shared CD ROM drive when requested by the BCM Imaging Tool To load the BCM Image 1 Connect the required equipment to the Business Communications Manager For information about how to connect the equipment refer to Connecting to the Business Communications Manager on page 13 Turn on the monitor connected to the Business Communications Manager If you are using a USB CD ROM drive turn on the CD ROM drive power switch If you are using an IDE CD ROM drive connect power to the Business Communications Manager to power up the CD ROM drive 4 Load the BCM Imaging Tool CD into the CD ROM drive connected to the Business Communications Manager 5 If you are using a USB CD ROM drive connect power to the Business Communications Manager If you are using an IDE CD ROM drive reboot the Business Communications Manager by disconnecting power from the Business Communications Manager and then reconnecting power The Startup Menu appears BCM Imaging Tool User Guide 24 Loading the BCM Image 6 10 Ma
21. ications Manager 10 Use the Tab key to highlight the OK button and press the Enter key or press Alt O The Select Media Location screen appears Select Media Location Local CD ROM 2 Network Share MS Cancel 11 Use the Tab key to select the Local CD ROM option and then press the Space bar BCM Imaging Tool User Guide 22 Loading the BCM Image 12 Use the Tab key to highlight the OK button and press the Enter key or press Alt O Follow the instructions on the screen to continue Make sure you have the BCM Image CDs ready to insert when requested by the BCM Imaging Tool Note After you insert a CD in the CD ROM drive wait at least 5 seconds before you press the Enter key This allows the CD ROM drive time to recognize the new CD If you press Enter before the CD ROM drive is ready you will receive an error message Leave the CD in the CD ROM drive wait at least 5 seconds and then press the Enter button If the error message gives you the option of Abort or Retry press the R button 13 Use the Tab key to highlight the OK button and press the Enter key or press Alt O The Image File Needed screen appears 14 Insert the first BCM Image CD into the CD ROM drive A Warning screen appears Warn ing You are about to re clone your BCH This will destroy all exising data Image name 26641115 qho Are you sure you want to continue Yes ELIM 15 Press the Enter key and follow the instructions on the screen
22. ing the BCM Image from a CD ROM drive To load the BCM Image from a CD ROM drive you must have a CD ROM drive connected to the Business Communications Manager system Tip Loading the BCM Image from an IDE CD ROM drive is much faster than loading the BCM Image from a USB CD ROM drive If you connected a USB CD ROM drive to the Business Communications Manager load the BCM image using a shared network drive whenever possible Loading the BCM Image from a shared network drive significantly reduces the amount of time it takes to load the BCM Image Loading from a USB CD ROM drive takes approximately 65 minutes while loading from a shared drive or IDE CD ROM drive takes approximately 15 minutes 1 Connect the required equipment to the Business Communications Manager For information about how to connect the equipment refer to Connecting to the Business Communications Manager on page 13 Turn on the monitor connected to the Business Communications Manager If you are using a USB CD ROM drive turn on the CD ROM drive power switch If you are using an IDE CD ROM drive connect power to the Business Communications Manager to power up the CD ROM drive 4 Load the BCM Imaging Tool CD into the CD ROM drive connected to the Business Communications Manager 5 If you are using a USB CD ROM drive connect power to the Business Communications Manager If you are using an IDE CD ROM drive reboot the Business Communications Manager by disconne
23. ng the BCM Image 25 Select Media Location t 2 Local CD ROM Network Share RS Cancel 11 Use the Tab key to select the Network Share option and then press the Space bar 12 Use the Tab key to highlight the OK button and press the Enter key or press Alt 0 The Select Network Type screen appears Select Metwork Type lt gt DHCP Enabled 2 Static IP RS Cancel 13 If your network uses DHCP use the Tab key to highlight the OK button and press the Enter key or press Alt Q Proceed to Step 20 If you are using a local computer or your networks does not use DHCP use the Tab key to select the Static IP option and then press the Space bar 14 Use the Tab key to highlight the OK button and press the Enter key or press Alt O The Enter Network IP Info screen appears Enter Network IF Info IP 1H 10 18 1 subnet 255 255 255 6 Gateway LIS Ok Cancel Back 15 Enter the IP address of the Business Communications Manager system and press the Tab key The Subnet field is highlighted 16 Enter the Subnet mask of the Business Communications Manager and press the Tab key The Gateway field is highlighted 17 If the computer with the shared drive is on a different subnet enter the IP address of gateway for the network to which the Business Communications Manager is connected and press the Tab key If the computer with the shared drive is on the same subnet press the Tab key The WINS field is highlighted
24. nications Manager model BCM 1000 BCM 200 or BCM 400 and software version BCM 3 0 BCM 3 0 1 BCM 3 5 BCM 3 6 or greater Security note If you loaded Business Communications Manager software version 3 5 Q Telnet and BCM Drive Shares are enabled To ensure optimal security you should disable these two settings For information on how to disable Telnet settings refer to the Business Communications Manager Programming Operations Guide For information about how to disable the BCM Drive Shares refer to the Business Communications Manager Management User Guide BCM Imaging Tool User Guide 34 Returning the Business Communications Manager to normal operation Restoring the Business Communications Manager programming After you have finished initializing the hard disk you can restore the Business Communications Manager system programming To restore the programming you can use the Backup and Restore Utility BRU or you can manually enter the program settings Restoring the Business Communications Manager programming using BRU To restore the programming using BRU you must have previously created a backup of the system programming using BRU If you do not have a backup you must restore the programming manually Note You can use BRU only if you loaded the same Business Communications Manager software version that the backup was made with For example to use a backup created on Business Communications Manager software version 3 5
25. nnect using an Ethernet crossover cable 28 Returning the Business Communications Manager to normal operation 29 Removing a USB CD ROM drive from a BCM 200 or BCM 400 30 Removing an IDE CD ROM drive from a BCM 200 or BCM 400 30 Removing an IDE CD ROM drive from a BCM 1000 0 000 30 Disconnecting the monitor and keyboard from a BCM 1000 44 31 Disconnecting the monitor and keyboard from a BCM 200 or BCM 400 31 BCM Imaging Tool User Guide 4 Contents Restarting the Business Communications Manager 00000 e eee e eee 33 Initializing the Business Communications Manager hard disk 005 33 Restoring the Business Communications Manager programming 5 34 Restoring the Business Communications Manager programming using BRU 34 Restoring the Business Communications Manager programming manually 34 lle ee ee a ee ee ee er ee ee ee ET 35 it a ee ree ee ee ee ee ee eee ee ee ee ee ee ee 37 P0609711 01 01 Figures Figure 1 Overview of using the BCM Imaging Tool 0 000 eee ees 11 Figure 2 Overview of connecting the required equipment to the Business Communications Manager 13 Figure 3 Location of the ports on a BCM 1000 0 c eee eee ees 14 Figure 4 Remove the base function tray bezel 0 0 ce ees 15 Figure 5 Location of the ports ona BCM 200 0 ccc eee
26. nt to use for sharing 2 Enable sharing on the folder and set the permissions so that the Business Communications Manager can access this folder For information about how to enable sharing or set the permissions refer to the documentation for your computer 3 Copy the contents of the BCM Imaging Tool CD into the shared folder Make sure the contents of the BCM Imaging Tool CD are at the top level of the folder 4 Copy the contents of BCM Image CDs into the shared folder Make sure the contents of all of the BCM Image CDs are at the top level of the folder 5 Repeat step 4 for each version of the BCM Image CDs you want to load Configuring your computer to connect using an Ethernet crossover cable When you are connecting your computer to the Business Communications Manager using an Ethernet crossover cable or a local hub or switch you must change the network settings on your computer The table below shows the recommended settings for this type of connection Network settings on your ee Value BCM Imaging Tool setting Value Pe Select Network Type Static IP a Address 10 10 10 100 PIP 10 10 10 1 Subnet mask 255 255 255 0 Subnet 255 255 255 0 Default Gateway 10 10 10 100 Gateway 10 10 10 100 For information about how to set the network parameters on your computer refer to your Operating System documentation Note Make sure you record your current network setting so you can change them back when you are finished using the
27. osition Slide base function tray partially into the platform base chassis Fasten base function tray latch screws P0609711 01 01 Returning the Business Communications Manager to normal operation 33 Restarting the Business Communications Manager If you removed the Business Communications Manager from the rack or wall replace it 2 Plug the Business Communications Manager and the expansion unit if there is one into the AC power source The Business Communications Manager automatically starts booting The reboot can take several minutes to complete Note Plug in the expansion unit immediately after plugging in the Business Communications Manager to ensure synchronization between the two units 3 Reconnect all the connectors to the front of the units Initializing the Business Communications Manager hard disk After you have finished applying the BCM Image you must initialize the hard disk This restores several key settings that are normally set at the factory For information about how to initialize the hard drive refer to Initialize the Hard Disk in the Business Communications Manager Installation and Maintenance Guide The procedure for initializing the hard disk is different on the various Business Communications Manager software versions For this reason make sure you use the Installation and Maintenance Guide for the correct Business Commu
28. ossary provides terms used in the BCM Imaging Tool User Guide BCM Image A copy of the contents of a Business Communications Manager hard drive as it was when it was shipped from the factory IDE CD ROM drive A CD ROM drive that connects to the IDE cable on a computer system This is normally an internal CD ROM drive Unified Manager Unified Manager is a web based navigation tool that allows you to view and change all operations and maintenance programming on the Business Communications Manager system USB CD ROM drive A CD ROM drive that connects to the USB port on a computer system This is normally an external CD ROM drive BCM Imaging Tool User Guide 36 Glossary P0609711 01 01 Index A Access Code 21 24 acronyms 8 B Backup and Restore Utility 34 BCM 1000 IDE CD ROM drive connecting 17 IDE CD ROM drive removing 30 keyboard connecting 14 keyboard disconnecting 31 monitor connecting 14 monitor disconnecting 31 ports location 14 BCM 200 IDE CD ROM drive connecting 17 IDE CD ROM drive removing 30 keyboard connecting 14 keyboard disconnecting 31 monitor connecting 14 monitor disconnecting 31 ports location 15 USB CD ROM drive connecting 17 USB CD ROM drive removing 30 BCM 400 IDE CD ROM drive connecting 17 IDE CD ROM drive removing 30 keyboard connecting 14 keyboard disconnecting 31 monitor connecting 14 monitor disconnecting 31 ports location 16 USB CD ROM drive conne
29. phony connections connecting 33 disconnecting 13 text conventions 7 tip 7 U USB cable 17 USB CD ROM drive connecting to BCM 200 17 connecting to BCM 400 17 removing from BCM 200 30 removing from BCM 400 30 requirements 16 W Warning symbol 7 WINS server 25 Index 39 BCM Imaging Tool User Guide 40 Index P0609711 01 01
30. r BCM 400 With the rear of top cover slightly raised slide the top cover forward until the cover engages with the BCM 200 or BCM 400 Press the top cover down until it rests on the BCM 200 or BCM 400 Install the two top cover screws at the rear of the platform base chassis Removing an IDE CD ROM drive from a BCM 1000 N O O A W foe Disconnect the power cable from the BCM 1000 Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface Disconnect the IDE ribbon cable from the CD ROM drive Disconnect the power connector from the CD ROM drive Remove the CD ROM drive from the BCM 1000 Set the top cover on the BCM 1000 With the rear of top cover slightly raised slide the top cover forward until the cover engages with the BCM 1000 Press the top cover down until it rests on the BCM 1000 Install the two top cover screws at the rear of the platform base chassis P0609711 01 01 Returning the Business Communications Manager to normal operation 31 Disconnecting the monitor and keyboard from a BCM 1000 To disconnect the monitor and keyboard 1 Remove the monitor and keyboard cables from the Business Communications Manager 2 Close the door on the bezel Disconnecting the monitor and keyboard from a BCM 200 or BCM 400 To disconnect the monitor and keyboard Make sure the Business Communications Manager is disconnected from the AC power outlet 2 Attach one end of a g
31. r press Alt Q If there is only one BCM Image on the shared drive a Verification screen appears Go to Step 27 If there 1s more than one BCM image on the shared drive the Image Selection screen appears Continue with Step 26 Use the Tab key to select the image file you want to load and press the Enter key A Verification screen appears P0609711 01 01 Loading the BCM Image 27 27 Use the Tab key to highlight the Yes button and press the Enter key or press Alt Y Note If you are using a shared CD ROM drive you must insert the BCM Imaging Tool CD and the BCM Image CDs in the shared CD ROM drive when prompted by the BCM Imaging Tool 28 When the BCM Imaging Tool has finished loading the BCM Image the BCM Imaging Completed screen appears You can now return the Business Communications Manager system to its normal operating configuration using the steps in Returning the Business Communications Manager to normal operation on page 29 ECH Imaging Completed The BCH has been successfully imaged You can now restart the system Please disconnect any device used during the BIT process BCM Imaging Tool User Guide 28 Loading the BCM Image Preparing a shared network drive If you are loading the BCM Image from a shared network drive you must load the contents of the BCM Imaging Tool CD and the BCM Image CDs onto the network drive before you start To prepare the network drive Create a folder on the computer you wa
32. r the system cD Text conventions This guide uses the following text conventions italic text Indicates book titles Example Business Communications Manager Installation and Maintenance Guide bold text Indicates items on the screen or keys on the keyboard Example Press the Enter key BCM Imaging Tool User Guide 8 Acronyms Acronyms This guide uses the following acronyms BRU Backup and Restore Utility DHCP Dynamic Host Configuration Protocol IDE Integrated Device Electronics IP Internet Protocol LAN Local Area Network PC Personal Computer USB Universal Serial Bus WAN Wide Area Network WINS Windows Internet Name Service Related publications For more information about using Business Communications Manager refer to the following publications Programming Operations Guide This document provides information about configuring the Business Communications Manager Management User Guide This document provides information about managing the Business Communications Manager including how to use the Backup and Restore Utility BRU Software Keycode Installation Guide This document provides information about obtaining and adding software keycodes to the Business Communications Manager system Installation and Maintenance Guide This document provides information about installing and maintaining a Business Communications Manager system P0609711 01 01 How to gethelp 9 How to get help USA and Can
33. rounding strap to your wrist and the other end to a grounded metal surface Disconnect the monitor and keyboard cables from the BCM 200 or BCM 400 Move the base function tray latches to the unlocked position Position the bezel below and between the base function tray latches Lift the bezel until the bezel clips line up with the corresponding base function tray bezel holes 6 Tilt the bezel forward then push the bottom of the bezel into the base function tray chassis to engage the bezel clips 7 Push on the face of the bezel so that it rests flush with the face of the base function tray chassis 8 Install the base function tray bezel screws See Figure 8 Figure 8 Install the base function tray bezel Push bezel against base function tray Install Bezel LO screws g ii Insert bezel clips Position bezel into base function between latches and tray chassis move upward BCM Imaging Tool User Guide 32 Returning the Business Communications Manager to normal operation 9 Push the base function tray completely into the chassis Be careful not to crimp the DS30 ribbon cables 10 Move the base function tray latches to the locked position Refer to Figure 9 11 Install the base function tray latch screws Figure 9 Install the base function tray Connect DS30 cables to the MSC Insert base function tray completely Move base function tray latches to the locked p
34. s Communications Manager to the LAN card on the local computer or e Use a standard Ethernet cable to connect the LAN card on the Business Communications Manager to a port on a local hub or switch Use a second Ethernet cable to connect the LAN card on the local computer to another port on the local hub or switch P0609711 01 01 Loading the BCM Image 19 Loading the BCM Image The BCM Image 1s a copy of the contents of the Business Communications Manager hard drive as it was when it was shipped from the factory You load the BCM Image when you want to change the Business Communications Manager applications and settings back to their factory defaults Two examples of when you might load the BCM Image are e if there has been a serious configuration error that does not allow the Business Communications Manager to start up e the Business Communications Manager system has been returned from a lease customer and you want to reset it to factory condition A Warning Loading the BCM Image erases all of the information that has been stored on the Business Communications Manager hard drive This includes keycodes application patches configuration programming voice messages and greetings Note that telephony programming is not stored on the hard drive and therefore is not erased when you load a BCM image If you want to erase the telephony programming you must perform a system startup For information about how to perform a system startup
35. you must have loaded the BCM Image for software version 3 5 onto the Business Communications Manager To restore the system programming 1 Install any patches that are applicable for this Business Communications Manager system Note Only install the patches that you know operate properly on this Business Communications Manager system 2 Use the Backup and Restore Utility BRU to restore a known working copy of system programming The restore also loads all of the software keycodes for the system For information about how to use BRU refer to the Business Communications Manager Management User Guide m Note Make sure the Registry option in the Select BCM Component s box is not _ selected before you restore the programming Restoring the Business Communications Manager programming manually 1 Add all of the software keycodes that are applicable for this Business Communications Manager system For information about adding keycodes refer to the Software Keycode Installation Guide Install any patches that are applicable for this Business Communications Manager system Note Only install the patches that you know operate properly on this Business Communications Manager system Use Unified Manager to manually configure the Business Communications Manager system For information about how to use Unified manager refer to the Business Communications Manager Programming Operations Guide P0609711 01 01 35 Glossary This Gl
Download Pdf Manuals
Related Search