Avaya BayRS Version 15.2.0.0 User's Manual
Contents
1. Site Manager Procedure You do this System responds 1 In the Configuration Manager window The RADIUS Access Control window choose Protocols gt Global Protocols gt opens RADIUS gt Access Control 2 Set the User Manager Lock parameter to Enable For more information click on Help or see the parameter descriptions beginning on page A 13 3 Click on OK You return to the Configuration Manager window 314470 15 2 Rev 00 6 3 BayRS Version 15 2 0 0 Document Change Notice Login Accounting BayRS RADIUS accounting is now supported for console and Telnet router logins The following sections new to Configuring RADIUS describe the functionality that was added to support this feature You determine whether a console or Telnet login session should allow RADIUS accounting messages to be sent to the RADIUS server by enabling or disabling RADIUS accounting access to the server Using the BCC To allow RADIUS accounting messages to be sent to the RADIUS server navigate to the access prompt for example box access and enter user access radius account enable enable To prevent RADIUS accounting messages from being sent to the RADIUS server navigate to the access prompt for example box access and enter user access radius account enable disable Note If you enable login accounting and the RADIUS server becomes unavailable the value for the user access radius account enable paramete2. With earlier versions of BayRS you enabled the user manager lock using the Technician Interface only You can now enable it using the BCC or Site Manager The lock is disabled by default allowing access by all users with the user or manager profile and also by individual users with a unique profile You enable the lock when both the RADIUS client and server are available You disable the lock if the RADIUS server is not available allowing the user to log in with the manager or user profile 314470 15 2 Rev 00 Configuring RADIUS When you enable the user manager lock and a RADIUS server is unavailable for authentication the router automatically disables the user manager lock When the RADIUS server becomes available the router automatically enables the user manager lock Note Be sure to configure RADIUS and assign the appropriate access to individuals with unique profiles before you enable the user manager lock otherwise you may lock out system managers from the router Using the BCC To restrict access to individual users only navigate to the access prompt for example box access and enter user manager lock enable To allow access by all users with the manager or user profile in addition to users with a unique profile navigate to the access prompt for example box access and enter user manager lock disable Using Site Manager To restrict access to individual users only complete the following tasks
3. Passport 5430 For information about installing an ATM T3 E3 PMC module see ATM T3 E3 PMC Module Supplement Creating an ATM Circuit for a T3 or E3 Connection on a Passport 5430 To start ATM services on an ATM T3 E3 PMC module in the Passport 5430 you do the following 1 Configure the physical ATM circuit 2 Add protocols and other services to that circuit This section describes how you create a physical ATM circuit for a T3 or E3 connection on a Passport 5430 then directs you to Configuring ATM Services for information about adding protocols and further configuring ATM services Using the BCC To add ATM to a Passport 5430 with a T3 E3 connector navigate to the box prompt and enter atm slot lt s ot_number gt pci slot lt pci_slot gt module lt module_number gt connector lt connector_number gt mode t3 e3 slot_number is the number of the chassis slot containing the ATM T3 E3 PMC module 314470 15 2 Rev 00 1 1 BayRS Version 15 2 0 0 Document Change Notice pci_slot is the number of the PCI slot containing the ATM T3 E3 PMC module The PCI slot number for the ATM T3 E3 PMC module is always 1 module_numberis always 2 for the ATM interface connector_numberis the number of a connector on the ATM T3 E3 PMC module mode t3 or mode e3 specifies whether the ATM interface is a T3 or E3 interface For example the following command adds an ATM T3 interface to the Passport 5430 configuration on slot 1 PCI slot 1 m
4. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE In addition the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure that may incorporate by reference certain limitations and notices imposed by third parties ji 314470 15 2 Rev 00 Nortel Networks Inc Software License Agreement This Software License Agreement License Agreement is between you the end user Customer and Nortel Networks Corporation and its subsidiaries and affiliates Nortel Networks PLEASE READ THE FOLLOWING CAREFULLY YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND OR USE THE SOFTWARE USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT If you do not accept these terms and conditions return the Software unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price Software is owned or licensed by Nortel Networks its parent or one of its subsidiaries or affiliates and is copyrighted and licensed not sold Software consists of machine readable instructions its components data audio visual content such as images text recordings or pictures and related licensed materials including all whole or partial copies Nortel Networks grants you a license to use the Software only in the country where you acquired the Software You obtain
5. ATM devices with different settings for scrambling cannot communicate For example if you configure a router to enable scrambling and configure a hub to disable scrambling the router and the hub cannot communicate If you select On be sure to enable scrambling for all devices on the network If you select Off be sure to disable scrambling for all devices on the network 1 3 6 1 4 1 18 3 4 23 3 2 1 22 314470 15 2 Rev 00 A 7 BayRS Version 15 2 0 0 Document Change Notice Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Per VC Clipping Configuration Manager gt ATM1 gt ATM Line Attributes Disable Enable Disable Enables or disables cell clipping on a per VC basis Accept the default Disable for normal VC clipping Enable this parameter if you want to clip cells on a per VC basis 1 3 6 1 4 1 18 3 4 23 3 1 1 17 DS3 Line Build Out Configuration Manager gt ATM1 gt ATM Line Attributes Short Short Long Conditions router signals to mitigate attenuation which depends on the physical length of the line You can set this parameter only for DS3 modules Select Short for lines shorter than 225 feet select Long for lines 225 feet or longer 1 3 6 1 4 1 18 3 4 23 3 2 1 23 A 8 314470 15 2 Rev 00 Site Manager Parameters Frame Relay PVC Parameter You use the following parameter
6. OK The ATM Configuration window opens 11 Click on ATM The Edit ATM Connector window opens 12 Go to Defining an ATM Service Record in Configuring ATM Services After you create the ATM circuit go to Chapter 2 Starting ATM and ATM Router Redundancy in Configuring ATM Services to finish configuring ATM services Configuring ATM Services also provides more information about ATM services and how to modify an existing ATM configuration 314470 15 2 Rev 00 1 7 Chapter 2 Configuring Bridging Services Version 15 2 0 0 The following section corrects erroneous text in Configuring Bridging Services Interfaces Supported The section Interfaces Supported under Implementation Notes in Configuring Bridging Services incorrectly states that the translation bridge can operate on all SR interfaces supported by Nortel Networks routers except IP The translation bridge can operate on all SR interfaces supported by Nortel Networks routers except for interfaces configured for SRB with IP encapsulation 314470 15 2 Rev 00 2 1 Chapter 3 Configuring Differentiated Services Version 15 1 0 0 The following section describes a change to Configuring Differentiated Services Modifying RED Parameters The following change is required to Table 6 1 in the Modifying RED Parameters section of the Configuring Differentiated Services book The proper range of values for the id parameter is from 1 throu
7. OK to accept the default circuit name The ATM Configuration window opens Click on Physical Layer Configuration The Physical Layer Configuration window opens 4 Click on either DS3 or E3 The Port Parameters window opens 5 To configure port parameters set the following parameters as needed e Enable Disable e Line Type e Setup Alarm Threshold seconds e Clear Alarm Threshold seconds e Loopback Configuration e Primary Clock Click on Help or see the parameter descriptions in ATM Port Parameters beginning on page A 2 Click on OK The Physical Layer Configuration window opens Click on Done The ATM Configuration window opens Click on ATM Line Attributes The ATM Line Driver Attributes window opens continued 1 6 314470 15 2 Rev 00 Configuring ATM Services Site Manager Procedure continued 9 You do this Set the the following parameters as needed e Enable e Interface MTU Data Path Enable Data Path Notify Timeout e Framing Mode e Cell Scrambling e Per VC Clipping e DS3 Line Build Out Note The Cell Scrambling parameter value must be the same as for the other ATM devices on your network See your system administrator or your service provider for the appropriate value Click on Help or see the parameter descriptions in ATM Line Parameters on page A 5 System responds 10 Click on
8. Protocols gt RADIUS gt Access Control Disabled Enable Disable Allows you to modify access to the router by enabling or disabling the user manager lock Set to Enable to lock out the user and manager profile and allow access only by individual users with a unique profile Accept the default value Disable to allow access by all users with the manager or user profile in addition to users with a unique profile Note If the user manager lock is enabled and the RADIUS server becomes unavailable the message RADIUS wait state appears in the User Manager Lock field When the RADIUS server becomes available the value reverts to Enable 1 3 6 1 4 1 18 3 3 2 22 1 10 Login Accounting Protocols gt Global Protocols gt RADIUS gt Access Control Disable Enable Disable Enables or disables login accounting Set to Enable 1f you want RADIUS Accounting messages to be sent to the RADIUS server Accept the default value Disable to prevent RADIUS accounting messages from being sent to the server 1 3 6 1 4 1 18 3 3 2 22 1 11 314470 15 2 Rev 00
9. You can purchase selected documentation sets CDs and technical publications through the Internet at the www1 fatbrain com documentation nortel URL How to Get Help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller contact the technical support staff for that distributor or reseller for assistance If you purchased a Nortel Networks service program contact one of the following Nortel Networks Technical Solutions Centers Technical Solutions Center Telephone 33 4 92 966 968 800 4NORTEL or 800 466 7835 61 2 9927 8800 800 810 5000 Europe Middle East and Africa North America Asia Pacific China as as SN Additional information about the Nortel Networks Technical Solutions Centers is available from the www nortelnetworks com help contact global URL An Express Routing Code ERC is available for many Nortel Networks products and services When you use an ERC your call is routed to a technical support person who specializes in supporting that product or service To locate an ERC for your product or service go to the http www 130 nortelnetworks com cgi bin eserv common essContactUs jsp URL xii 314470 15 2 Rev 00 Chapter 1 Configuring ATM Services Version 15 2 0 0 The following section is new to Configuring ATM Services You use the procedures in this section to configure an ATM T3 E3 PMC module installed in a
10. no rights other than those granted to you under this License Agreement You are responsible for the selection of the Software and for the installation of use of and results obtained from the Software 1 Licensed Use of Software Nortel Networks grants Customer a nonexclusive license to use a copy of the Software on only one machine at any one time or to the extent of the activation or authorized usage level whichever is applicable To the extent Software is furnished for use with designated hardware or Customer furnished equipment CFE Customer is granted a nonexclusive license to use Software only on such hardware or CFE as applicable Software contains trade secrets and Customer agrees to treat Software as confidential information using the same care and discretion Customer uses with its own similar information that it does not wish to disclose publish or disseminate Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement Customer shall not a use copy modify transfer or distribute the Software except as expressly authorized b reverse assemble reverse compile reverse engineer or otherwise translate the Software c create derivative works or modifications unless expressly authorized or d sublicense rent or lease the Software Licensors of intellectual property to Nortel Networks are beneficiaries of this provision Upon termination or breach of the license by Customer or in
11. or T3CBITPLCP For E3 make sure that the ATM line attribute Framing Mode is set to either E3_G751 or E3_G832 1 3 6 1 4 1 18 3 4 26 10 1 7 Setup Alarm Threshold seconds Configuration Manager gt ATMI gt Physical Layer Configuration gt DS3 or E3 2 2 to 10 Sets the time interval in seconds during which the device driver tolerates a performance defect or anomaly If the performance defect or anomaly is still present when time interval expires the device driver records a performance failure and logs an event message Set the timer value in seconds 1 3 6 1 4 1 18 3 4 26 10 1 17 314470 15 2 Rev 00 A 3 BayRS Version 15 2 0 0 Document Change Notice Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Clear Alarm Threshold seconds Configuration Manager gt ATMI gt Physical Layer Configuration gt DS3 or E3 2 2to10 Specifies the clear time in seconds for performance failure conditions If the defect or anomaly clears within this interval the device driver records a performance cleared condition and logs an event message Set the timer value in seconds 1 3 6 1 4 1 18 3 4 26 10 1 18 Loopback Configuration Configuration Manager gt ATMI gt Physical Layer Configuration gt DS3 or E3 No Loopback No Loopback Payload Loopback Line Loopback Forces the interface into loopback mode
12. side of the router The bootstrap border router allows you to create two or more PIM bootstrap domains in one PIM domain so that the rendezvous point RP information kept in the routers can be different To specify a PIM bootstrap router as a border router complete the following tasks Site Manager Procedure You do this System responds 1 In the Configuration Manager window choose Protocols The Protocols menu opens 2 Choose IP The IP menu opens 3 Choose PIM The PIM menu opens continued 314470 15 2 Rev 00 5 1 BayRS Version 15 2 0 0 Document Change Notice Site Manager Procedure continued You do this 4 Choose Interface System responds The PIM Interface Parameters window opens 5 Set the Bootstrap Border parameter Click on Help or see the parameter description in IP PIM Parameter on page A 10 6 Click on OK You return to the Configuration Manager window 314470 15 2 Rev 00 Chapter 6 Configuring RADIUS Version 15 2 0 0 The following sections are amendments to Configuring RADIUS Topic Page Configuring a RADIUS Client Using Site Manager 6 1 Modifying Router Access Using the BCC or Site Manager 6 2 Using SecurlD for RADIUS Authentication 6 5 Configuring a RADIUS Client Using Site Manager With earlier versions of Site Manager you configured RADIUS only on link modules that had sync
13. to BayRS Version 15 x The following section describes changes to Upgrading Routers to BayRS Version 15 x Why You Upgrade Boot and Diagnostic PROMs Table A 1 in Why You Upgrade Boot and Diagnostic PROMs of Upgrading Routers to BayRS Version 15 x has been modified to include the latest boot and diagnostic PROM file names and associated revision numbers for router platforms running BayRS Version 15 x Diagnos Diagnostic tic PROM Reason for Boot PROM Router PROM Revision Upgrading Boot PROM Revision Platform File Name Number PROM File Name Number AN ANH andiag exe 7 36 Strata flash fea anboot exe 9 00d ture support ARN arndiag exe 2 24 Strata flash fea arnboot exe 1 27 ture support arndiag rom 2 24 Not applicable arnboot rom 1 27 e7srom rom 2 16 E7S feature sup isdb rom 1 06 port arn_pdbrom rom 1 22 Not applicable 314470 15 2 Rev 00 9 1 BayRS Version 15 2 0 0 Document Change Notice Diagnos Diagnostic tic PROM Reason for Boot PROM Router PROM Revision Upgrading Boot PROM Revision Platform File Name Number PROM File Name Number ASN asndiag exe 2 36 Strata flash fea asnboot exe 13 00 ture support asndiag rom 2 36 Not applicable BN frediag exe 5 16 Strata flash fea freboot exe 13 00 ture support fre4diag ppc 1 14 FRE 4 board fre4boot ppc 13 20 support ARE BN 5782 MPE arediag ppc 1 22 Strata flash fea areboot ppc 14 0 1 0 tur
14. traffic shaping Set the following parameters e Committed Burst Excess Burst e Throughput Bw Threshold Click on Help or see the parameter description in Frame Relay PVC Parameter on page A 9 Click on Done You return to the Frame Relay Service List window Click on Done You return to the Frame Relay Circuit Definition window Click on Done You return to the Configuration Manager window Version 15 2 0 0 The following section describes a limitation that was omitted from Configuring Frame Relay Services Deleting PVCs from Service Records The section Deleting PVCs from Service Records in Configuring Frame Relay Services should include the statement that Site Manager does not allow users to delete or move the last PVC in the only non default service record If you want to delete or move the last PVC you must remove the entire service record 4 2 314470 15 2 Rev 00 Chapter 5 Configuring IP Multicasting and Multimedia Version 15 2 0 0 Services The following section is new to Configuring IP Multicasting and Multimedia Services Configuring a PIM Bootstrap Border Router You can define a router as a PIM bootstrap border router PBBR by specifying at least one of its interfaces as a PIM bootstrap border interface PBBI A bootstrap border router prevents a bootstrap message that is received from one side of a border router from being passed to the other
15. BayRS Version 15 2 0 0 Part No 314470 15 2 Rev 00 January 2002 600 Technology Park Drive Billerica MA 01821 4130 BayRS Version 15 2 0 0 Document Change Notice NORTEL NETWORKS Copyright O 2002 Nortel Networks All rights reserved January 2002 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Nortel Networks NA Inc The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that license The software license agreement is included in this document Trademarks Nortel Networks the Nortel Networks logo the Globemark Unified Networks AN ARN ASN BayRS BCC BN Passport and System 5000 are trademarks of Nortel Networks Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated An asterisk after a name denotes a trademarked item Restricted Rights Legend Use duplication or disclosure by the United States Government is subject to restrictions as set forth in subparagraph c 1 Gi of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 Notwithstanding any othe
16. IB refer to Using Technician Interface Software Caution The Technician Interface does not verify that the value you enter for a parameter is valid Entering an invalid value can corrupt your configuration ATM Port Parameters Parameter Path Default Options Function Instructions MIB Object ID You use the following parameters to configure the ATM T3 E3 interface on the Passport 5430 Enable Disable Configuration Manager gt ATM1 gt Physical Layer Configuration gt DS3 or E3 Enable Enable Disable Enables or disables this interface Set to Disable only if you want to disable the interface 1 3 6 1 4 1 18 3 4 26 10 1 2 A 2 314470 15 2 Rev 00 Site Manager Parameters Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Line Type Configuration Manager gt ATMI gt Physical Layer Configuration gt DS3 or E3 Autodetect For DS3 the options are DS3 M23 DS3 CBIT Parity Autodetect For E3 the options are E3 Framed E3 PLCP Sets the frame format for this interface Determines the framing mode for this interface For DS3 if you choose DS3 M23 or DS3 CBIT Parity be sure that the ATM line attribute Framing Mode is appropriately set If the Line Type is DS3 M23 Framing Mode should be DS3_M23 or T3M23PLCP If Line Type is DS3 CBIT Parity Framing Mode should be DS3_CBIT
17. PROFITS OR SAVINGS WHETHER IN CONTRACT TORT OR OTHERWISE INCLUDING NEGLIGENCE ARISING OUT OF YOUR USE OF THE SOFTWARE EVEN IF NORTEL NETWORKS ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIR POSSIBILITY The forgoing limitations of remedies also apply to any developer and or supplier of the Software Such developer and or supplier is an intended beneficiary of this Section Some jurisdictions do not allow these limitations or exclusions and in such event they may not apply 4 General a If Customer is the United States Government the following paragraph shall apply All Nortel Networks Software available under this License Agreement is commercial computer software and commercial computer software documentation and in the event Software is licensed for or on behalf of the United States Government the respective rights to the software and software documentation are governed by Nortel 314470 15 2 Rev 00 iii Networks standard commercial license in accordance with U S Federal Regulations at 48 C F R Sections 12 212 for non DoD entities and 48 C F R 227 7202 for DoD entities Customer may terminate the license at any time Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license In either event upon termination Customer must either return the Software to Nortel Networks or certify its destruction Customer is responsible for payment of any taxes including personal pr
18. The far end or intermediate equipment then performs diagnostics on the network between that equipment and the T3 E3 interface After testing set this parameter to No Loopback to return the interface to a normal operating mode e No Loopback Returns the interface to non loopback operation e Payload Loopback The received signal at this interface is looped through the device Typically the received signal is looped back for re transmission after it has passed through the device s framing function e Line Loopback The received signal at this interface does not go through the framing device minimum penetration but is looped back out Select the loopback configuration option 1 3 6 1 4 1 18 3 4 26 10 1 9 A 4 314470 15 2 Rev 00 Site Manager Parameters Parameter Primary Clock Path Configuration Manager gt ATMI gt Physical Layer Configuration gt DS3 or E3 Default Loop Options Internal Loop Function Specifies the clock signal source Instructions Select Internal if you want the router to generate the clock signal source MIB Object ID Otherwise accept the default Loop if you want the clock signal source to be external to the router 1 3 6 1 4 1 18 3 4 26 10 1 11 ATM Line Parameters You use the following parameters to configure ATM line details on the Passport 5430 The type of ATM link module you use determines the line details that you can edit Parameter Enable Path Configuration Manage
19. ce Shows menu paths Example Protocols gt IP identifies the IP option on the Protocols menu Separates choices for command keywords and arguments Enter only one of the choices Do not type the vertical line when entering the command Example If the command syntax is show ip alerts routes you enter either show ip alerts or show ip routes but not both This guide uses the following acronyms ARN ATM FDDI IP MTU PBBI PBBR PIM PMC PVC RADIUS SRB VC Advanced Remote Node asynchronous transfer mode Fiber Distributed Data Interface Internet Protocol maximum transmission unit PIM bootstrap border interface PIM bootstrap border router Protocol Independent Multicast PCI mezzanine card permanent virtual circuit Remote Access Dial In User Services source route bridge virtual circuit 314470 15 2 Rev 00 xi BayRS Version 15 2 0 0 Document Change Notice Hard Copy Technical Manuals You can print selected technical manuals and release notes free directly from the Internet Go to the www nortelnetworks com documentation URL Find the product for which you need documentation Then locate the specific category and model or version for your hardware or software product Use Adobe Acrobat Reader to open the manuals and release notes search for the sections you need and print them on most standard printers Go to Adobe Systems at the www adobe com URL to download a free copy of the Adobe Acrobat Reader
20. ce is b3zs Specifying the Line Type To specify the line type for this interface navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter line type lt type gt type is autodetect ds3m23 or ds3cbitparity for the ATM T3 interface and e3framed or e3plcp for the ATM E3 interface If the line type is ds3m23 the framing mode should be m23 or t3m23plcp If the line type is ds3cbitparity the framing mode should be cbit or t3cbitplcp If the line type is either e3framed or e3plcp the framing mode should be either g751or g832 For instructions on setting the framing mode parameter see Configuring ATM Services Specifying the Loopback Mode To force the interface into loopback mode so that the far end or intermediate equipment can perform diagnostics on the network between that equipment and the T3 E3 interface navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter loopback mode lt type gt 314470 15 2 Rev 00 1 3 BayRS Version 15 2 0 0 Document Change Notice type is payloadloop or lineloop If you select payloadloop the received signal at this interface is looped through the device Typically the received signal is looped back for retransmission after it has passed through the device s framing function If you select lineloop the received signal at this interface does not go through the framing device minimum penetration but is looped back out The d
21. e support Passport 2430 pp2430diag exe 1 18 Not applicable pp2430boot ppc 14 10 pp2430ram exe 1 18 Not applicable Passport 5430 pp5430diag exe 1 10 Not applicable pp5430boot ppc 15 2 0 0 pp5430ram exe 1 10 Not applicable pp5430diag a 1 10 DS3 E3 feature support and quad serial feature support System 5000 s5000diag exe 0 04 Strata flash fea s5000boot exe 13 00 net modules ture support 314470 15 2 Rev 00 Appendix A Site Manager Parameters This appendix describes the following Site Manager parameters Topic Page ATM Port Parameters A 2 ATM Line Parameters A 5 Frame Relay PVC Parameter A 9 IP PIM Parameter A 10 RADIUS Client Parameters SCH RADIUS Access Control Parameters A 13 You can display the same information using Site Manager online Help For each parameter this appendix provides the following information e Parameter name e Configuration Manager menu path e Default setting e Valid parameter options e Parameter function e Instructions for setting the parameter e Management information base MIB object ID 314470 15 2 Rev 00 A 1 15 2 0 0 Document Change Notice BayRS Version You can also use the Technician Interface to modify parameters by issuing set and commit commands with the MIB object ID This process is the same as modifying parameters using Site Manager For information about using the Technician Interface to access the M
22. efault is noloop For example the following command changes the loopback mode to payloadloop atm e3 1 1 2 1 loopback mode payloadloop atm e3 1 1 2 1 Defining the Interface MTU The maximum transmission unit MTU is the largest possible unit of data that the physical medium can transmit By default the interface allows an MTU size of 4608 octets This value can handle most packet sizes However you can set the MTU to any value from 3 through 4608 octets To modify the interface MTU navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter mtu lt integer gt integer is the MTU size in octets For example the following command sets the MTU size to 3000 octets atm e3 1 1 2 1 mtu 3000 atm e3 1 1 2 1 Defining the Primary Clock Source To define the clock signal source navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter primary clock source lt value gt value is internal or loop If you select internal the router will generate the clock signal source If you select the default loop the clock signal source will be external to the router 314470 15 2 Rev 00 Configuring ATM Services For example the following command sets the clock source to internal atm e3 1 1 2 1 primary clock source internal atm e3 1 1 2 1 Specifying the Setup Alarm Threshold To specify the duration of time in seconds that elapses following the detection of a perfo
23. est version of Nortel Networks BayRS and Site Manager software For information about upgrading BayRS and Site Manager see the upgrading guide for your version of BayRS 314470 15 2 Rev 00 ix BayRS Version 15 2 0 0 Document Change Notice Text Conventions This guide uses the following text conventions angle brackets lt gt bold text braces italic text Indicate that you choose the text to enter based on the description inside the brackets Do not type the brackets when entering the command Example If the command syntax is ping lt ip_address gt you enter ping 192 32 10 12 Indicates command names and options and text that you need to enter Example Enter show ip alerts routes Example Use the dinfo command Indicate required elements in syntax descriptions where there is more than one option You must choose only one of the options Do not type the braces when entering the command Example If the command syntax is show ip alerts routes you must enter either show ip alerts or show ip routes but not both Indicates new terms book titles and variables in command syntax descriptions Where a variable is two or more words the words are connected by an underscore Example If the command syntax is show at lt valid_route gt valid_route is one variable and you substitute one value for it 314470 15 2 Rev 00 separator gt vertical line Acronyms Prefa
24. gh 65535 The proper range is shown in the following table which lists RED parameters that can be configured under dsqms red their values and functions Parameter Values Function id integer 1 through 65535 Identifies the RED function You cannot change this parameter min threshold integer 0 through 100 default 20 Indicates the queue size below which no packets are dropped by RED max threshold integer 1 through 100 default 80 Indicates the queue size above which all pack ets are dropped by RED first order const integer 0 through 100 default 1 Specifies the first order constant used when calculating drop probability based on the aver age queue fraction the queue size and the min threshold value second order const integer 0 through 1000 default 10 Specifies the second order constant used when calculating drop probability based on the average queue fraction the queue size and the min threshold value 314470 15 2 Rev 00 BayRS Version 15 2 0 0 Document Change Notice Version 15 2 0 0 The following section corrects erroneous text in the description of the Priority parameter Priority Parameter The description of the Priority parameter in Appendix A incorrectly states that the lower the number the higher the priority The description should state that the higher the number the higher the priority For example a server with a priority of 2
25. hronous interfaces With Version 15 2 0 0 you can use Site Manager to configure RADIUS on any link module including Quad Ethernet FDDI and token ring Consequently Site Manager no longer automatically configures a demand circuit group when you use it to configure a RADIUS client 314470 15 2 Rev 00 6 1 BayRS Version 15 2 0 0 Document Change Notice To enable RADIUS on a router slot and configure the RADIUS client Site Manager Procedure You do this System responds 1 In the Configuration Manager window The RADIUS Client Parameters window select Protocols gt Global Protocols gt opens The window lists the slots that RADIUS gt Create RADIUS already have RADIUS configured on them 2 Click on Add For multislot routers the RADIUS Slot Selection window opens For single slot routers the RADIUS Client Parameters window opens Go to step 4 3 Enter the slot number on which you want The RADIUS Client Parameters window to configure RADIUS and click on OK opens 4 Set the following parameters e Authentication e Accounting Client IP Address Debug Message Level Click on Help or see the parameter descriptions beginning on page A 11 5 Click on OK You return to the RADIUS Client Parameters window Modifying Router Access Using the BCC or Site Manager With RADIUS you can modify access to the router using the user manager lock and the login accounting feature User Manager Lock
26. ng Services DIN A Ee eee eee e 2 1 WSEAS e ei 2 1 Chapter 3 Configuring Differentiated Services KN E E Peers a ai 3 1 Modimo RED ISS ee anni 3 1 314470 15 2 Rev 00 v Verson ATS D GE 3 2 Priority Parameter errr sean Pe Ee e EEN SE feiereg Chapter 4 Configuring Frame Relay Services verdon TTO EE 4 1 Using Taffie Shaping Site Manager aan Eege 4 1 IN TSA A aupa aa aa a aa Deleting PVCs from Service Records E geg dial SAS SE Me EE a 4 2 Chapter 5 Configuring IP Multicasting and Multimedia Services VO KA sn 5 1 Configuring a PIM Bootstrap Border Router viu ed 5 1 Chapter 6 Configuring RADIUS Version 15 2 0 0 errr Perr nieta seca EE a boda hend cc Configuring a RADIUS Client Using Site Manager cccescceesteeceneeeeeteeeeeeeeees 6 1 Modifying Router Access Using the BCC or Site Manager ssssnsssnnssnnnssnnsinneeennne 6 2 UsenMeanager LOCK ansieht 6 2 LOU ACCOUN ee Using SecurlD for RADIUS Authentication eeh Pe E illa PERA a 0D Chapter 7 Using the Technician Interface Scripts O 7 1 Using Scripts and Aliases to Dynamically Configure a Router enen 7 1 Chapter 8 Using the Technician Interface Software KE E EE Ee Eege BEE eh eu e eko geb E al Diagnostics On Off Option for ARN Passport 2340 and Passport 5430 8 1 Setting Default Route Cost Using the Technician Interface 8 1 Chapter 9 Upgrading Routers to Ba
27. odule 2 connector 1 box atm slot 1 pci slot 1 module 2 connector 1 mode t3 atm 1 1 2 1 To configure T3 E3 parameters use the following procedures Specifying the Cable Length To specify the cable length navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter cable length lt ength gt length is either short default or long Specify short for a cable less than 225 feet long specify long for a cable length of 225 feet or more For example the following command changes the cable length to long atm e3 1 1 2 1 cable length long atm e3 1 1 2 1 Specifying the Clear Alarm Threshold To specify the duration of time in seconds that elapses following the clearing of a performance failure before the condition is registered and logged navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter clear alarm threshold lt integer gt integer is a value from 2 through 10 seconds inclusive 314470 15 2 Rev 00 Configuring ATM Services For example the following command changes the clear alarm threshold from 2 to 8 seconds atm e3 1 1 2 1 clear alarm threshold 8 atm e3 1 1 2 1 Specifying the Line Coding Method To specify the line coding method navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter line coding hdb3 b3zs The default for the ATM E3 interface is hdb3 and the default value for the ATM T3 interfa
28. operty taxes resulting from Customer s use of the Software Customer agrees to comply with all applicable laws including all applicable export and import laws and regulations Neither party may bring an action regardless of form more than two years after the cause of the action arose The terms and conditions of this License Agreement form the complete and exclusive agreement between Customer and Nortel Networks This License Agreement is governed by the laws of the country in which Customer acquires the Software If the Software is acquired in the United States then this License Agreement is governed by the laws of the state of New York 314470 15 2 Rev 00 Contents Preface BEISIEe AUS nee ut ix WER LONENIONE sii x o o e eeaereiurleree xi Hard Copy Technical Manuals alada EE a xii Howto eet EE xii Chapier 1 Configuring ATM Services FO IL ri 1 1 Creating an ATM Circuit for a T3 or E3 Connection on a Passport 5430 1 1 Specifying the Cable Length a iaa Gatti ey E Specifying the Clear Alarm Threshold viii ni 1 2 Specifying the Line Coding Method AAA 1 3 Speelivind the Line DPE naar 1 3 Specilyingiihe Loopback Moda a 1 3 Defining the Interface MTU nennen sera 1 4 Detining the Primary Clock Bolten Gente 1 4 Specifying the Setup Alarm Threshold AAA 1 5 Disabling and Reenabling the ATM interface ecssecceceeeseeceeeeneeeeeeeeneeees 1 5 Chapter 2 Configuring Bridgi
29. ounting 1 3 6 1 4 1 18 3 5 22 1 1 3 314470 15 2 Rev 00 BayRS Version 15 2 0 0 Document Change Notice Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Client IP Address Protocols gt Global Protocols gt RADIUS gt Create RADIUS gt Add or Protocols gt Global Protocols gt RADIUS gt Edit RADIUS gt Edit None A 32 bit IP address Identifies the RADIUS client This address applies to the entire router Enter the IP address of the router If the RADIUS server is already configured Site Manager automatically supplies the address 1 3 6 1 4 1 18 3 5 22 1 1 5 Debug Message Level Protocols gt Global Protocols gt RADIUS gt Create RADIUS gt Add or Protocols gt Global Protocols gt RADIUS gt Edit RADIUS NODEBUG ONE TWO THREE NODEBUG Assigns the level of RADIUS debug messages that the RADIUS client logs Accept the default value NODEBUG unless you are specifically trying to debug the connection 1 3 6 1 4 1 18 3 5 22 1 1 7 314470 15 2 Rev 00 Site Manager Parameters RADIUS Access Control Parameters Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID You use the following parameters to modify router access User Manager Lock Protocols gt Global
30. r 1s automatically set to serverwait When the RADIUS server becomes available again the value reverts to enabled 6 4 314470 15 2 Rev 00 Configuring RADIUS Using Site Manager To allow RADIUS accounting messages to be sent to the RADIUS server complete the following tasks Site Manager Procedure You do this System responds 1 In the Configuration Manager window The RADIUS Access Control window choose Protocols gt Global Protocols gt opens RADIUS gt Access Control 2 Setthe Login Accounting parameter to Enable For more information click on Help or see the parameter descriptions beginning in page A 13 3 Click on OK You return to the Configuration Manager window Using SecurlD for RADIUS Authentication This section in Configuring RADIUS incorrectly states that Nortel Networks implements SecurID on ARN routers only Nortel Networks implements SecurID on all router platforms that operate as RADIUS clients 314470 15 2 Rev 00 6 5 Chapter 7 Using the Technician Interface Scripts Version 15 1 0 0 The Technician Interface is a command line interface that Nortel Networks support technicians can use to troubleshoot and configure Nortel Networks devices The following section is an amendment to Using the Technician Interface Scripts Using Scripts and Aliases to Dynamically Configure a Router Use of rapid fire scripts or aliases to dynamically set a router
31. r gt ATM1 gt ATM Line Attributes Default Enable Options Enable Disable Function Instructions MIB Object ID Enables or disables the line driver Select Enable or Disable 1 3 6 1 4 1 18 3 4 23 3 2 1 2 Parameter Interface MTU Path Configuration Manager gt ATM1 gt ATM Line Attributes Default 4608 Options 0 to 9188 Function Specifies the largest packet size in octets that the router can transmit on this interface Instructions Enter a value that is appropriate for the network MIB Object ID 1 3 6 1 4 1 18 3 4 23 3 2 1 9 314470 15 2 Rev 00 A 5 BayRS Version 15 2 0 0 Document Change Notice Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Data Path Enable Configuration Manager gt ATM1 gt ATM Line Attributes Enable Enable Disable Specifies whether the router disables the interface between the driver and the higher level software the data path interface when you disconnect the cable from the ATM module If you select Enable then when you disconnect the cable from the ATM module the router disables the data path interface after the time you specify with the Data Path Notify Timeout parameter If you select Disable the router does not disable the data path interface when you disconnect the cable from the ATM module Select Enable or Disable If you select Enable be su
32. r license agreement that may pertain to or accompany the delivery of this computer software the rights of the United States Government regarding its use reproduction and disclosure are as set forth in the Commercial Computer Software Restricted Rights clause at FAR 52 227 19 Statement of Conditions In the interest of improving internal design operational function and or reliability Nortel Networks Inc reserves the right to make changes to the products described in this document without notice Nortel Networks Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Portions of the code in this software product may be Copyright 1988 Regents of the University of California All rights reserved Redistribution and use in source and binary forms of such portions are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation advertising materials and other materials related to such distribution and use acknowledge that such portions of the software were developed by the University of California Berkeley The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED AS IS AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION
33. re to enter an appropriate value for the Data Path Notify Timeout parameter 1 3 6 1 4 1 18 3 4 23 3 2 1 11 Data Path Notify Timeout Configuration Manager gt ATM1 gt ATM Line Attributes 1 0 to 3600 Specifies the time in seconds that the router waits before disabling the data path interface when you disconnect the cable from the ATM module providing that you set the Data Path Enable parameter to Enable Accept the default or enter an appropriate value 1 3 6 1 4 1 18 3 4 23 3 2 1 12 A 6 314470 15 2 Rev 00 Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID Site Manager Parameters Framing Mode Configuration Manager gt ATM1 gt ATM Line Attributes DS3_CBIT for DS3 lines E3_G832 for E3 lines TIADM for DS1 lines E1ADM for El lines DS3_CBIT DS3_M32 T3CBITTPLCP T3M23PLCP E3_G751 E3_G832 Specifies the transceiver mode for the physical interface Select a transceiver mode as follows e DS3_CBIT DS3_M32 T3CBITTPLCP or T3M23PLCP for DS3 modules E3_G751 or E3_G832 for E3 modules 1 3 6 1 4 1 18 3 4 23 3 2 1 17 Cell Scrambling Configuration Manager gt ATM1 gt ATM Line Attributes Off On Off If you select On the router randomizes cell payload sufficiently to guarantee cell synchronization If you select Off cell synchronization problems can occur Note that
34. rmance failure before the condition is registered and logged navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter setup alarm threshold lt integer gt integer is a value from 2 through 10 seconds inclusive For example the following command changes the setup alarm threshold from 2 to 8 seconds atm e3 1 1 2 1 setup alarm threshold 8 atm e3 1 1 2 1 Disabling and Reenabling the ATM interface By default the ATM interface is enabled when you create the circuit However you can disable or reenable the interface at any time When the interface is enabled traffic can flow over the interface When the interface is disabled traffic cannot flow over the interface To disable or reenable the ATM interface navigate to the ATM interface prompt for example box atm 1 1 2 1 atm e3 and enter state disabled enabled For example the following commands disable and reenable the ATM interface atm e3 1 1 2 1 state disabled atm e3 1 1 2 1 state enabled atm e3 1 1 2 1 314470 15 2 Rev 00 1 5 BayRS Version 15 2 0 0 Document Change Notice Using Site Manager To create an ATM circuit for a T3 or E3 connection on a Passport 5430 complete the following tasks Site Manager Procedure You do this System responds 1 In the Configuration Manager window click on the ATM DS3 E3 interface ATM1 in slot 1 PCI slot 1 module 2 The Add Circuit window opens Click on
35. s configuration via the MIBs can put the router into a corrupted state and cause connectivity issues When you use the Technician Interface to launch scripts or aliases to configure the router be sure to include pauses one to two seconds to allow sufficient time for the router to make the required changes to the MIBs 314470 15 2 Rev 00 7 1 Chapter 8 Using the Technician Interface Software Version 15 1 0 0 The Technician Interface is a command line interface that Nortel Networks support technicians can use to troubleshoot and configure Nortel Networks devices The following sections are amendments to Using the Technician Interface Software Diagnostics On Off Option for ARN Passport 2340 and Passport 5430 For ARN Passport 2430 and Passport 5430 platforms only the Technician Interface diags command supports an option to enable or disable diagnostics effective the next time you cycle power on the router Disabling the diagnostics results in a faster boot time but leaves the hardware components unverified The syntax for this option is as follows diags onloff lt s ot_id gt Setting Default Route Cost Using the Technician Interface When the routing table does not contain the route to a particular destination address the router looks for a default route As it does for any other route the routing table either acquires the default route dynamically through a routing protocol or you can enter the default route sta
36. s in accordance with RFC 2362 it accepts incoming messages and forwards outgoing ones Set to Enable if you want the interface to discard incoming and outgoing bootstrap messages Accept the default Disable if you want the interface to accept incoming messages and forward outgoing messages 1 3 6 1 4 1 18 3 5 3 14 2 1 32 A 10 314470 15 2 Rev 00 Site Manager Parameters RADIUS Client Parameters Parameter Path Default Options Function Instructions MIB Object ID Parameter Path Default Options Function Instructions MIB Object ID You use the following parameters to configure a RADIUS client This section replaces Client IP Address Parameter in Appendix A of Configuring RADIUS Authentication Protocols gt Global Protocols gt RADIUS gt Create RADIUS gt Add or Protocols gt Global Protocols gt RADIUS gt Edit RADIUS Disable Enable Disable Enables or disables the RADIUS client on the gateway Set to Enable to activate the RADIUS client on the router Accept the default value Disable to deactivate RADIUS authentication 1 3 6 1 4 1 18 3 5 22 1 1 2 Accounting Protocols gt Global Protocols gt RADIUS gt Create RADIUS gt Add or Protocols gt Global Protocols gt RADIUS gt Edit RADIUS Disable Enable Disable Enables or disables RADIUS accounting Set to Enable to activate RADIUS accounting Accept the default value Disable to deactivate RADIUS acc
37. the event designated hardware or CFE is no longer in use Customer will promptly return the Software to Nortel Networks or certify its destruction Nortel Networks may audit by remote polling or other reasonable means to determine Customer s Software activation or usage levels If suppliers of third party software included in Software require Nortel Networks to include additional or different terms Customer agrees to abide by such terms provided by Nortel Networks with respect to such third party software 2 Warranty Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer Software is provided AS IS without any warranties conditions of any kind NORTEL NETWORKS DISCLAIMS ALL WARRANTIES CONDITIONS FOR THE SOFTWARE EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON INFRINGEMENT Nortel Networks is not obligated to provide support of any kind for the Software Some jurisdictions do not allow exclusion of implied warranties and in such event the above exclusions may not apply 3 Limitation of Remedies IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANY OF THE FOLLOWING a DAMAGES BASED ON ANY THIRD PARTY CLAIM b LOSS OF OR DAMAGE TO CUSTOMER S RECORDS FILES OR DATA OR c DIRECT INDIRECT SPECIAL INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING LOST
38. tically 314470 15 2 Rev 00 8 1 BayRS Version 15 2 0 0 Document Change Notice You can use the Technician Interface to set the wfRipIntfDefaultRouteCost RIP default route cost MIB attribute This attribute interacts with the Site Manager parameter Default Route Supply or BCC parameter default supply in one of two ways e If you select Enable for Default Route Supply or default supply RIP advertises the default route cost you set for wfRipIntfDefaultRouteCost attribute plus the default route learned from the network e Ifyou select Generate for Default Route Supply or default supply RIP advertises the default route cost you set for wfRipIntfDefaultRouteCost For additional information see Supplying a Default Route on an Interface in Configuring IP ARP RARP RIP and OSPF Services With the Technician Interface enter the following commands to set the wfRipIntfDefaultRouteCost RIP default route cost attribute set wfRipIntfDefaultRouteCost lt value gt value is any integer from 0 through 15 The default value is 1 commit save config lt vol gt lt filename gt You must have Manager access to issue a set command The commit command causes the changes you made to the configuration to take effect in active memory but not in flash memory The save config command saves changes to a configuration file config and flash volume on the router 8 2 314470 15 2 Rev 00 Version 15 2 0 0 Chapter 9 Upgrading Routers
39. to specify the bandwidth threshold that you want to set for this frame relay PVC Parameter Path Default Options Function Instructions MIB Object ID Bw Threshold Configuration Manager gt Protocols gt Frame Relay gt Services gt PVCs 0 0 to maximum physical line speed bits s Specifies the bandwidth threshold that you want to set for this PVC for traffic shaping purposes To minimize starvation of normal and low priority traffic over a high speed physical line such as a 56 Kb s lines over HSSI set the bandwidth threshold to a value 3 to 10 times that set for the Throughput CIR parameter Otherwise accept the default 0 1 3 6 1 4 1 18 3 5 9 9 2 1 58 314470 15 2 Rev 00 A 9 BayRS Version 15 2 0 0 Document Change Notice IP PIM Parameter Parameter Path Default Options Function Instructions MIB Object ID You use the following parameter to determine whether the router interface will act as a PIM bootstrap border interface Bootstrap Border Protocols gt IP gt PIM gt Interface Disable Disable Enable When you set this parameter to Enable this PIM interface acts as a PIM bootstrap border interface A bootstrap border interface discards both incoming and outgoing bootstrap messages Incoming messages originate from other PIM routers outgoing messages originate from other PIM interfaces on the same router When you set this parameter to Disable this interface operate
40. will be the active server before a server with a priority of 1 3 2 314470 15 2 Rev 00 Chapter 4 Configuring Frame Relay Services Version 15 1 0 0 The following changes are required to the Configuring Frame Relay Services book A new frame relay parameter Bw Threshold has been added to the PVC List for Services window in Site Manager The Bw Threshold parameter works in conjunction with the Committed Burst Excess Burst and Throughput parameters to shape traffic The following sections update the Site Manager procedure within the Using Traffic Shaping section in Chapter 4 and adds the parameter description to Appendix A Site Manager Parameters Using Traffic Shaping Site Manager To enable traffic shaping complete the following tasks using Site Manager Site Manager Procedure You do this System responds 1 In the Configuration Manager window The Edit Connector window opens click on a port configured for frame relay 2 Click on Edit Circuit The Frame Relay Circuit Definition window opens 3 Click on Services The Frame Relay Service List window opens continued 314470 15 2 Rev 00 4 1 BayRS Version 15 2 0 0 Document Change Notice Site Manager Procedure continued You do this 4 Select the appropriate service record and click on PVCs System responds The FR PVC List for Service window opens Click on a PVC that you want to configure for
41. yRS Version 15 x Kl A EE 9 1 Why You Upgrade Boot and Diagnostic PROMS E deuda eg del vi 314470 15 2 Rev 00 Appendix A Site Manager Parameters GEELEN ege A 2 ATM Dne Partes sra rr it ida andes A 5 Frame Relay PVC Parameter anseesne eege Gees geen eege Ee ee u A 9 IP PIM Parameter a RE Banane A 10 RADIUS Client Parameters u a annnnnnnnnnnnnenn nnd nnennnn A 11 RADIUS Access Control Parameters aan A 13 314470 15 2 Rev 00 vii Preface BayRS Version 15 2 0 0 is a software release that includes bug fixes and new features added since BayRS Version 15 1 0 0 This document change notice contains amendments to the following BayRS manuals e Configuring ATM Services e Configuring Bridging Services e Configuring Differentiated Services e Configuring Frame Relay Services e Configuring IP Multicasting and Multimedia Services e Configuring RADIUS e Configuring the Technician Interface Scripts e Configuring the Technician Interface Software e Upgrading Routers to BayRS Version 15 x Before You Begin Before using this notice you must complete the following procedures For a new router e Install the router see the installation guide that came with your router e Connect the router to the network and create a pilot configuration file see Quick Starting Routers Configuring Remote Access for AN and Passport ARN Routers or Connecting ASN Routers to a Network Make sure that you are running the lat
Download Pdf Manuals
Related Search