Avaya BayRS Version 12.01 and Site Manager Version 6.01 Release Notes
Contents
1. Site Manager does not allow you to configure OSPF and DVMRP on the same circuit CR 33557 X 25 The QLLC window contains two parameters PU type and Generate XID for which Site Manager requires you to enter valid values However when you enter values exit the window and then reenter the window Site Manager clears the values from the fields 32 301894 A Rev 00 Release Notes CR 34391 DLSw When you configure a new DLSw SDLC circuit in dynamic mode the Source SAP and Destination SAP parameters are missing from the DLS Local Device Configuration window Also Site Manager corrupts the values you entered for the Source MAC and Destination MAC parameters CR 33935 ATM A program error occurs when you click the SAAL button from the Edit ATM Connector window in Site Manager CR 34119 Site Manager Site Manager does not allow you to change the name of an ISDN leased line configured on a BRI interface when using the Change Lines option from the Circuit Definition window CR 33521 MCT1 E1 The error message Protocol ST2 or RSVP must be configured to edit line resources appears when you attempt to edit logical line resources on a non PRI circuit CR 32524 PPP A new PPP parameter RFC 1661 Compliance has been added in the PPP line list Enabling this field will allow the router to run in compliance with RFC 1661 CR 33299 ATM The SSCS TYPE field is not listed when you display an IP interface in Site M2. If there are many hosts learned through the port the IP host cache causes a slot reset when you enable it 301894 A Rev 00 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 32880 IP When telnetting from a BLN router configured for host only mode the router faults in ip_del c at line 252 This occurs only on the first telnet attempt after you boot the router CR 33496 IP There is a problem in 11 02 and later whereby a router does not cache any IP frames destined for hosts that are unresolved Prior to 11 02 if a router received IP traffic destined for a local host for which it did not have an ARP entry the router would cache up to the first 4 frames received for this host while attempting to resolve the address CR 33867 IP Enabling extended traffic filters in ISP mode causes a fault in ip_fwd_frag CR 33872 IP Packets are lost when you enable IP_ETF with ISP mode already enabled CR 34359 IP A router configured with ISP enabled and handling heavy traffic may encounter a BGP OSPF soloist failure in ip_barp_operational_act 0x0 routing after the slot runs out of memory CR 34265 IP An error occurs in ISP mode resulting in a watchdog fault after BGP experiences multiple failed TCP connections CR 32277 IP RIP2 may advertise the same networks multiple times during a periodic update if a particular type of RIP policy filter is in place The policy filter is configured to gene
3. BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes BayRS Version 12 01 Site Manager Software Version 6 01 Part No 301894 A Rev 00 March 1998 GIS Bay Networks Se Bay Networks 4401 Great America Parkway 8 Federal Street Santa Clara CA 95054 Billerica MA 01821 Copyright 1998 Bay Networks Inc All rights reserved Printed in the USA March 1998 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Bay Networks Inc The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that license A summary of the Software License is included in this document Trademarks AN BLN GAME and Bay Networks are registered trademarks and ARN BayRS Bay Networks Press and the Bay Networks logo are trademarks of Bay Networks Inc All other trademarks and registered trademarks are the property of their respective owners Restricted Rights Legend Use duplication or disclosure by the United States Government is subject to restrictions as set forth in subparagraph c 1 i of the Right
4. CR 30499 IP Added the MIB variable wfBgpPeerEntry wfB gpPeerASLoopDetect Default value disabled to determine if a Peering session should be torn down if an AS Loop is detected in the AS Path In all cases the route s will be marked as unusable Disabled Peering will remain up Enabled Peering will be dropped 301894 A Rev 00 Release Notes CR 27239 Translation Bridge Enhancement request to allow packets larger than Ethernet to be translated The current implementation allows only packet sizes of 1500 A new MIB parameter wfBrXbFddiBridge was added to the translation bridge base to allow FDDI and Token Ring size packets to be translated You enable this parameter only if there are no Ethernet ports being used for translation bridge on the router The mode must also be set to Ethernet II not 802 3 CR 25171 DECnet The router experiences a bus error when you delete DECnet in dynamic mode on a frame relay circuit CR 26560 SDLC You cannot establish an SNA session between a 3174 device configured as a pu2 1 device an SDLC attached frad630 device connected to another frad630 device via frame relay ban or bnn and an Ethernet attached host 3172 CR 32886 DLSw After a PU1 controller is disconnected and reconnected to the SDLC primary line on a router DLSw fails to cycle properly between disconnected and established states After entering an established state the AS 400 sends an XID poll which is tran
5. IPEX The valid values in the Value field and in the Help window do not match for the Ipex Gateway Mapping PVC LCN entry Destination PVC LCN should include a range between 1 and 4095 301894 A Rev 00 29 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 35239 X 25 QLLC When you configure X 25 QLLC Maps Site Manager leaves the Generate XID field blank CR 35348 Router Redundancy Clicking on Edit Lines for Ethernet and 100Base T router redundant interfaces brings up the 100Mb s CSMA CD parameters window which is incorrect Site Manager should bring up the Edit CSMA CD parameters window If you click on OK Site Manager displays the following message ERROR Invalid data entered for Interface Line Speed To exit the window you must click on Cancel or enter an incorrect value for line speed CR 34152 IP Traffic Filters When you reorder the IP traffic filters selecting INSERT AFTER inserts the filter before the precedence number that was selected in either dynamic or local mode on a PC CR 34229 IP Traffic Filters Reordering filters on an interface with less than 32 filters disables the IP Extended Support parameter When this happens interfaces that require this parameter to be enabled will not apply any filter above the 32nd filter CR 34297 PPP BCP is not enabled for PPP when SRB or LB is configured on a switched services circuit for example dial on dema
6. Site Manager displays the wrong part number For an ARE DS3 the correct part number is AG13110115 for an ARE E3 the correct part number is AG13110114 CR 34951 Static Routes Site Manager does not permit you to configure subnetted static routes CR 34717 ISDN Deleting a demand circuit dynamically fails to clear the local phone number entry 301894 A Rev 00 31 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 35118 BOD Site Manager allows Dynamic Monitor in the bandwidth mode for a leased line BOD which should only be Monitor or Non monitor The Dynamic Monitor is only used for Demand circuit with BOD CR 33967 IP When selecting Protocols IP RIP Interfaces from the Site Manager menu in Configuration Manager Site Manager faults This condition occurs on both UNIX and PC platforms CR 34335 Frame Relay When you delete a frame relay PVC or service record Site Manager does not display a confirmation prompt CR 34367 Source Route Bridge Site Manager does not allow you to add source route bridge SRB to a token ring interface SRB is not on the Protocols menu CR 34370 DLSw If you add DLSw to a second token ring network Site Manager sets the Bridge ID parameter to 0 CR 34407 Site Manager If you delete LLC from a token ring interface Site Manager also removes source route bridge from the interface This happens with SunOS and Win95 Site Manager CR 34199 OSPF
7. traffic is restored in only one direction CR 35100 IPEX When a router is configured in IPEX Gateway Mode it is unable to quickly bring up multiple sessions CR 35114 IPEX If you configure IPEX Gateway Mode over direct LAPB it causes a bus error when the session restarts CR 30446 ATMZ Traffic is shaped differently when the per VC clipping Atmizer feature is enabled than when it is disabled default CR 34833 MOSPF A tag violation results when bouncing a circuit and sending multicast traffic CR 32052 TCP An enhancement request to enable TCP to record who closed a connection in the log rather than merely that the connection was closed 301894 A Rev 00 Release Notes CR 35108 IPEX An enhancement request to identify IPEX log messages as error messages Currently only the function name and a value is logged but it is not clear that the value is an error code CR 34893 ATMZ_ARE A problem exists in 11 02 Revision 3 and later that causes an Inter Cell Gap that exceeds the configured Peak Cell Rate for a DS3 board CR 35065 TI When the date on a router is 2000 or greater that is 01 01 00 the log command using the d function does not work correctly Instead the command displays the entire log CR 33958 Packet Capture When using PCAP for a packet capture on a HSSI line if the packet exceeds 140 bytes PCAP will intermittently capture receive data before transmit If the pack
8. IP Traffic Filters Site Manager faults when trying to edit an inbound IP traffic filter dynamically in Configuration Manager CR 33719 IPEX After you delete all entries on the IPEX Mapping Table Configuration list screen the Add Delete and Apply buttons are no longer displayed making it impossible to add a new mapping without having to back out of this screen and go back in CR 33720 IPEX Every time you delete an X 25 IPEX service record a confirmation prompt appears making the task of deleting several service records a laborious one 301894 A Rev 00 37 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 33721 LAPB The values range for the TCP Port parameter on the LAPB IPEX Mapping Add window is incorrect The text for the parameter should also be changed to Remote TCP Port CR 33722 LAPB When you delete a LAPB Gateway circuit the wfLapbEntry for that circuit is not deleted CR 33765 X 25 The X25 mib has a new attribute wfLapbPktPduSize used to configure X 25 with the maximum message size from the X 25 client A new parameter Client PDU Size needs to be added to Site Manager to configure this attribute in the X 25 Packet Configuration window CR 32864 IPEX If a failure occurs at the remote IPEX IP interface IPEX can no longer establish TCP connections with the remote IPEX routers An enhancement to the current IPEX implementation allows you to configure the second
9. There is a race condition that may cause a bus error in MTM when DVMRP detects a routing change 301894 A Rev 00 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34104 OSPF An ARP request can be generated out the wrong interface when the OSPF next hop for that network is in transition A response from a device running proxy ARP at that time causes installation of the host route which results in traffic being forwarded out of the wrong interface CR 33928 OSPF A router configured for OSPF may fail to properly advertise a Type2 LSA for a network on which it is the designated router This results in a loss of connectivity to that network throughout the AS and routers not using that network in their shortest path first calculations CR 34395 OSPF If you bounce an Autonomous System Border Router ASBR in an OSPF area the Area Border Router ABR might permanently age out the Type 4 link for that ABR This eliminates connectivity to that ASB s external routes for all routers outside of that area CR 30029 OSPF If the OSPF backup soloist is enabled and the router receives a database description DD packet with bad a checksum the router generates a bus error CR 33035 OSPF The OSPF Multihop ECMP functionality fails to distribute networks across equal cost OSPF Point to Point paths in certain configurations CR 34155 OSPF An enhancement request to add gate statistic reporting cap
10. Wide Web at support baynetworks com How to Get Help If you purchased a service contract for your Bay Networks product from a distributor or authorized reseller contact the technical support staff for that distributor or reseller for assistance If you purchased a Bay Networks service program call one of the following Bay Networks Technical Solutions Centers Technical Solutions Center Telephone number Fax number Billerica MA 800 2LANWAN 978 916 3514 Santa Clara CA 800 2LANWAN 408 495 1188 Valbonne France 33 4 92 96 69 68 33 4 92 96 69 98 Sydney Australia 61 2 9927 8800 61 2 9927 8811 Tokyo Japan 81 3 5402 0180 81 3 5402 0173 Bay Networks Educational Services Through Bay Networks Educational Services you can attend classes and purchase CDs videos and computer based training programs about Bay Networks products Training programs can take place at your site or at a Bay Networks location For more information about training programs call one of the following numbers Region Telephone number United States and Canada 800 2LANWAN then enter Express Routing Code ERC 282 when prompted 978 916 3460 direct Europe Middle East and Africa 33 4 92 96 15 83 Asia Pacific 61 2 9927 8822 Tokyo and Japan 81 3 5402 7041 viii 301894 A Rev 00 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes This document
11. connect request to X 25 However no check is made to see if the needed circuit is operational This leads to a bus error no lapb buffers and other errors CR 34584 IPEX The PLP bound FIFO needs to be flushed when you get a TCP_CLOSE_MSG in the IPEX Establish state before sending a Packet Level Reset request to X 25 CR 34599 X 25 You cannot configure LAPB Direct Interface only circuits on SYNC and MCT1 interfaces CR 32864 IPEX If a failure occurs at the remote IPEX IP interface IPEX can no longer establish TCP connections with the remote IPEX routers An enhancement to the current IPEX implementation allows you to configure the secondary remote IP interface for backup using the new MIB attribute wflpexMappingRemoteBackuplIp CR 33576 X 25 Attempting to scale X 25 to 10 PVCs over 24 T1 logical channels using the FRE2 040 32M causes a GAME system error The same error occurs when attempting to scale X 25 to 32 PVCs over 24 T1 logical channels 301894 A Rev 00 25 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 33871 IPEX Clearing inbound X 25 calls causes bus errors to occur on a router configured with IPEX in end to end mode CR 32855 X 25 PVC fails to come up after dynamically adding an X 25 PVC circuit CR 33410 IPEX If the X 25 client timer expires while IPEX is waiting for a clear confirmation from the remote X 25 connection end to end mode only X 25 will clear t
12. lists the anomalies also referred to as bugs change requests or CRs that have been fixed in Bay Networks BayRS Version 12 01 and Site Manager Software Version 6 01 BayRS Version 12 01 includes all anomalies that were fixed in 12 00 Revisions 1 2 and 3 Site Manager Software Version 6 01 includes all anomalies that were fixed in 6 00 Revisions 1 2 and 3 Use the BayRS Version 12 00 and Site Manager Software Version 6 00 documentation with BayRS Version 12 01 and Site Manager Software Version 6 01 Maintenance Release Methodology BayRS Version 12 01 and Site Manager Software Version 6 01 are Maintenance Releases Bay Networks is introducing a new methodology for releasing Bay Networks routing software Maintenance Releases are designated by a change in the second number to the right of the decimal point They provide a collection of software bug fixes for the current Major Release No new software or hardware features or functionality for either software or hardware is introduced beyond that already contained in the current Major Release 301894 A Rev 00 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes A Maintenance Release will occur approximately each 3 to 4 months after a Major Release occurs A Maintenance Release replaces the current Major Release or the prior Maintenance Release on the Price List and will become the current shipping version of BayRS Each Maintenance Release will be a c
13. related technical data or information without first obtaining any required export licenses or other governmental approvals Without limiting the foregoing Licensee on behalf of itself and its subsidiaries and affiliates agrees that it will not without first obtaining all export licenses and approvals required by the U S Government i export re export transfer or divert any such Software or technical data or any direct product thereof to any country to which such exports or re exports are restricted or embargoed under United States export control laws and regulations or to any national or resident of such restricted or embargoed countries or ii provide the Software or related technical data or information to any military end user or for any military end use including the design development or production of any chemical nuclear or biological weapons 9 General If any provision of this Agreement is held to be invalid or unenforceable by a court of competent jurisdiction the remainder of the provisions of this Agreement shall remain in full force and effect This Agreement will be governed by the laws of the state of California Should you have any questions concerning this Agreement contact Bay Networks Inc 4401 Great America Parkway P O Box 58185 Santa Clara California 95054 8185 LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT UNDERSTANDS IT AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS LICENSEE FURTHER
14. the date of shipment This warranty does not apply if the media has been damaged as a result of accident misuse or abuse The Licensee assumes all responsibility for selection of the Software to achieve Licensee s intended results and for the installation use and results obtained from the Software Bay Networks does not warrant a that the functions contained in the software will meet the Licensee s requirements b that the Software will operate in the hardware or software combinations that the Licensee may select c that the operation of the Software will be uninterrupted or error free or d that all defects in the operation of the Software will be corrected Bay Networks is not obligated to remedy any Software defect that cannot be reproduced with the latest Software release These warranties do not apply to the Software if it has been i altered except by Bay Networks or in accordance with its instructions ii used in conjunction with another vendor s product resulting in the defect or iii damaged by improper environment abuse misuse accident or negligence THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Licensee is responsible for the security of its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or a
15. 83 IPEX Traffic is started over 240 sessions at 45 percent capacity Channel is reset by toggling the wfLogicalLineDisable parameter on bln43 client Each time you reenable channel 1 traffic is restarted over it eventually causing a bus error to occurs on the client side router CR 34417 IPEX The IPEX audit gate checks for both a buflist and signal parameter each time the gate is scheduled This violates GAME s operational model which states that the signal parameter is valid only when buflist is set to NULL CR 34418 IPEX After receiving credits from X 25 IPEX should check whether it has data to send to X 25 If IPEX fails to perform this check data could be retained in the FIFO CR 34419 IPEX Bad code segment occurring in IPEX FSM for the VC_DIED message while operating in an establish state CR 33716 IPEX Unable to restart IPEX client sessions on the router after terminating them 301894 A Rev 00 27 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes Site Manager Software Version 6 01 Fixed Anomalies Site Manager Software Version 6 01 is a post 6 00 revision This version is backward compatible and supports the following router software versions 12 01 12 00 11 02 11 01 11 00 CR 35251 OSPF Defaults are read from cdl generated ASCII output files Default values for MIBs of type GAUGE are represented as signed numbers Site Manager is reading only type integer val
16. AGREES THAT THIS AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN BAY NETWORKS AND LICENSEE WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS AGREEMENT NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST BAY NETWORKS UNLESS BAY NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT iv 301894 A Rev 00 Contents Technical Support Bay Networks Technical Publications vii Bay Networks Customer Service c cccceecceeeseeeeeeeceeceeeeeeeaeeeeeeeeeseaeeeseaeeseceeeseaeeeeeneees vii How to Get Help EE viii Bay Networks Educational Services ccccecceceeeeceeeeeeceaeeeeeaeececaeeeeaaeeseeeeeeseaeeneeeeees viii BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes Maintenance Release Methodology 1 Year 2000 Complian Ces ceiaiscoiveikes cannes dadan haaie anaana ddai nieveetieneeneeaseirientecs 2 Image Builder Operational Note c cccecececesceeeneeceeeeeeeaaeseceeeeeeeeesaaeeseeeeeeseaeeeseeeeeeeeeed 2 BayRS Version 12 01 Fixed Anomalies ccecccceceeeeceeeeeececeeeeeaeeeseeeeesaaeeeseeeeesnaeeesenees 3 Site Manager Software Version 6 01 Fixed Anomalies cc ccceeeeceeeeeeeeeeeesesaeeeeneees 28 301894 A Rev 00 V Technical Support Bay Networks Technical Publications You can now print technical manua
17. Site Manager uses 16 as the default when setting the HSSI CRC size According to the MIB Site Manager should use 32 as the default CR 26479 Statistics Manager If you view IPX circuit information for an inoperable or inactive interface the Statistics Manager displays the incorrect network and MAC address for that circuit CR 33004 Report Generator Report Generator cannot write to the root directory of a PC 34 301894 A Rev 00 Release Notes CR 33277 IP The TR End Station ARP type should not be an available option when editing the IP interface entry of a demand circuit group CR 29473 NTP IP Mask defaults to 0 0 0 0 in the NTP Access Configuration List window CR 28170 Router Redundancy Router Redundancy should allow you to select between 2 types of redundancy new and old CR 33823 ARN Sync The SYNC parameter screen for the V34 modem is missing the WAN Serial Interface Type field CR 33181 RSVP The TSpec bucket rate depth and peak rate values get corrupted when the RSVP soloist is running on an ARE processor CR 33665 DLSw Changing the source route Interface RD value on the DLSw Basic Interface window causes Site Manager to create a new source route interface CR 33931 Site Manager After you install Site Manager a message should appear indicating the environment variables that need to be defined to run Site Manager CR 33843 CRM When editing an existing CRM line entry on t
18. This could be a serious problem if PHY_B fails during those 50 seconds that PHY_A is disconnected CR 33880 DLSw DLSw does not use the Backup Peer Hold Down Timer after a TCP connection reset only after the DLSw keepalives are exhausted 4 301894 A Rev 00 Release Notes CR 34771 DLSw Connections may fail to establish because the router does not send multiple CANUREACH messages when it receives multiple XID T2 Polls CR 30952 DLSw The DLS slot memory statistics show erroneous memory usage by this DLS slot This condition reflects incorrect statistics and inhibits the establishment of new connections as the erroneous statistic is used to determine if DLS may acquire more memory from the system heap during connection establishment CR 34027 DVMRP DVMRP routes are not declared unreachable when the reporting neighbor times out DVMRP waits for the route expiration timer to expire before updating those routes CR 34103 DVMRP Router does not always prune s g caches for which there is neither a local member nor a downstream neighbor CR 34013 DVMRP If there is no DVMRP interface configured on the OSPF soloist slot the router does not propagate MOSPF routes to other DVMRP slots CR 34336 DVMRP DVMRP fails to delete mask entries from routes_by_mask_utbl in the base environment The mask entry should be deleted if it does not have a pointer to any routes in the main routing table CR 34890 DVMRP
19. VIDED AS IS AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE In addition the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure that may incorporate by reference certain limitations and notices imposed by third parties ji 301894 A Rev 00 Bay Networks Inc Software License Agreement NOTICE Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre enabled software each of which is referred to as Software in this Agreement BY COPYING OR USING THE SOFTWARE YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH BAY NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE If you do not accept these terms and conditions return the product unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price 1 License Grant Bay Networks Inc Bay Networks grants the end user of the Software Licensee a personal nonexclusive nontransferable license a to use the Software either on a single computer or if applicable on a single authorized device identified by host ID for which it was originally acquired b to co
20. ability to OSPF This new feature enables you to determine how many buffers were processed after each run of the OSPF receive gate and how many of each kind of OSPF messages were processed during that particular run 6 301894 A Rev 00 Release Notes CR 33984 OSPF An ABR will not originate a more specific summary net into a non backbone area when a less specific summary for that net is present in the non backbone area The ABR does not consider the validity of the less specific summary net or whether the less specific summary net is even present in the backbone LSDB CR 33616 OSPF Both the designated router DR ineligible and DR eligible routers flap they oscillate between down gt init and init gt down states CR 35249 OSPF On occasion OSPF fails to boot because a bus error occurs in ospf_create_sum_Isdb 0x1 la CR 34015 OSPF If you set the OSPF Range Status parameter to not advertise in the OSPF range window of Site Manager or wfOspfAreaRangeEntry wfOspfAreaRangeStatus it does not hide the summary or prevent it from being advertised to the backbone area CR 34266 SDLC A DLC SDLC DLSw connection does not recover after a virtual circuit is moved from an inactive to an active state CR 34754 IP A router configured for Dial Optimized Routing and with the broadcast timer set to 24 hours times out routing information protocol RIP routes before the broadcast timer expires CR 27260 IP
21. anager CR 28617 Site Manager When you configure a local phone number on a version 9 00 router using Site Manager 4 00 or greater an SNMP set error occurs CR 29030 Switch Services Site Manager allows you to configure a standby primary circuit configured as a frame relay backup primary circuit 301894 A Rev 00 33 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 33151 IPEX A problem exists between 11 00 and 11 02 and later implementations of IPEX in which an 11 02 router cannot establish calls with an 11 00 router Bay Networks has added a new IPEX parameter Insert Calling DTE Address The default is Disabled to prevent the calling DTE address from being added but will allow router software version 11 02 or greater to interoperate with lower revisions of code CR 33626 Multiline Configuring multiline PPP over HSSI interfaces using Site Manager Dynamic Configuration does not work wfCctOptsEntry instances are deleted during configuration CR 26320 PPP If you select a primary circuit from the Primary Circuit Definition Dialog box and then click on OK to exit from the box Site Manager changes the CHAP PAP password to the default CR 28205 Interface Redundancy Site Manager experiences a General Protection Fault GPF when you try to configure interface redundancy for router interfaces on a 5000 router This problem was found in Site Manager Version 5 0 CR 33533 HSSI
22. ary remote IP interface for backup using the new MIB attribute wflpexMappingRemoteBackupIp The new IPEX parameter in Site Manager is Remote Backup IP Address CR 34599 LAPB Site Manager does not allow you to configure LAPB Direct Interface circuits on SYNC and MCT 1 interfaces 38 301894 A Rev 00
23. e Manager Software Version 6 01 Release Notes CR 28807 FTP When you boot a router with FTP disabled you cannot initiate an FTP session to the router after enabling FTP CR 31649 PING MIB The reported IP ping round trip times are incorrect This affects both the TI ping command and the ping MIB CR 32394 Technician Interface A bus error may occur when using the embedded Technician Interface enable disable sync command and referencing the circuit by name not by number CR 32457 IGMP Although it creates forwarding entries IGMP does not always forward multicast packets CR 34068 IGMP An etror occurs in igmp_xmit_act when you send rsvp path igmp join and rsvp resv messages to a router along with data CR 33672 SYNC If a port on an octal sync card receives an excessive amount of errors it will cause lack of resource errors on the other ports that are on the same quic chip Then when the circuit experiencing the problem is disabled or fixed the other ports continue to have lack of resource errors even with minimal traffic load CR 33906 RSVP After you reset a circuit downstream routers generate the following message No outgoing interfaces CR 34085 QLLC A bus error occurs after you disable enable the QLLC map entry twice 301894 A Rev 00 Release Notes CR 33674 QLLC When disabling X25QllcMapEntry the state value does not change CR 34161 LLC A bus error occurs if you del
24. et size is 160 bytes or more PCAP always captures receive data before transmit CR 34387 TI A multiline multislot sync configuration returns zeroes or inaccurate values for wflfEntry entries reported for that circuit CR 34632 ATM An address exception error can occur in the ATMizer code when Per PVC cupping functionality is enabled CR 32167 AppleTalk A bus error occurs when you reset the AppleTalk base CR 34020 HSSI Bursts of packets on a high traffic HSSI line can cause an HSSI log message 301894 A Rev 00 15 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 35208 DLSw An llc qllc topology degrades as traffic volume increases CR 35267 AT A bus error will occur in at_aptf c line 339 upon receipt of a MAC IP packet CR 35322 X 25 If a configuration has multiple X 25 service records and you dynamically configure X 25 on a new slot that is for the first time a g_map error occurs This happens only using a dynamic configuration CR 34374 Fire Wall Multilayer 2 protocol encapsulation over different media fails if packets are received together in a list of buffers rather than one buffer at a time Similarly multilayer 3 protocols e g IP and IPX may not work either CR 32753 OSPF An area border router with area range summaries configured can get stuck ina load state while the other side of the adjacency is in a full state CR 33735 Switched Services Whe
25. ete an interface with LLC2 when Je ere is unloaded CR 34137 MOSPF The DLS slot fails if you globally disable MOSPF by selecting Protocols gt IP gt OSPF MOSPF QOSPF gt Global and changing the Multicast Extensions option from All Multicasting to None CR 34450 MOSPF Multicast data flows do not fully recover after a hardware failure CR 34589 MOSPF When you repeatedly join leave the same group with a silence period of at least 30 seconds between each cycle the traffic in the first 5 seconds may be dropped CR 33514 MOSPF After a reboot the multicast bit is not turned on for some imported DVMRP routes CR 33571 MOSPF After rebooting a remote DVMRP router traffic for source in the dvmrp cloud is not forwarded over pure MOSPF routes CR 34469 Frame Relay Traffic Shaping Traffic Shaping does not support values of 3 8 5 8 etc It is only able to deal with Tc values in the form of 1 n 1 3 1 2 1 4 etc CR 34548 RIP A RIP announce policy filter does not work properly if configured to filter on OSPF TAG type 301894 A Rev 00 11 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34596 SWSERV A fault occurs when you restart a BOD channel CR 29988 APPN The AN router experiences a fault in APPN indicating that the system buffer is not large enough This fault occurs only on the AN E S Ethernet Sync CR 32595 Telnet The ESC key Escape does no
26. etween 1971 and 2070 If you use 2 digit notation 71 through 99 becomes 1971 through 1999 and 00 through 70 becomes 2000 through 2070 CR 33910 SYSLOG A bus error may occur when you telnet to a router on which SYSLOG and WCP are enabled CR 33307 IPX Packets are not always forwarded out the direct route This problem can occur when an IPX route learned via RIP is also a directly connected route If the route is learned through RIP first and the cost of the RIP learned route is less than the directly connected route the directly connected route is dropped CR 34135 DLSw Heavy SDLC traffic volume occurring on the router may result in packet loss 301894 A Rev 00 21 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34000 Firewall Communication between the FireWall router and the management station will not occur properly if the firewall control gate initializes on a slot that does not have the IP address used to communicate from the router to the management station CR 32814 Technician Interface When you disable a terminal attached to a router running the Technician Interface on an ARE card the router enters the diagnostic state and fails to exit until you reset it CR 28911 GAME If you schedule a boot for the year 2000 or later you receive a Success status message instead of a Pending status message CR 32980 GAME File Manager misinterprets file date stamp
27. he PC an error message appears CR 33299 ATM_RFE SSCS TYPE field for IBM s ATMARP SRV is not listed when displaying an IP interface in Site Manager 301894 A Rev 00 35 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 33602 IP Site Manager allows static routes with invalid subnets to be created CR 33482 ARN ISDN If you open a local configuration file with an ISDN adapter module Port Application Mode configured for 2B D Site Manager displays the following message WARNING Empty Module 2 has circuits configured CR 33926 DLSw When you set the Source Route Internal LAN ID and the Source Route Bridge ID fields in the DLSw Basic Global window and click on OK the values do not get saved CR 33787 ISDN There is a problem with Site Manager that may result in Site Manager erroneously enabling BOFLs on an MCT 1 module If you select a primary circuit on an MCT 1 module from the Dial Backup Circuits window click on Cct Type to display the Circuit Type and the Backup Pool ID and then click on OK without making changes BOFLs are enabled on all logical lines of the MCT 1 This action causes all dial on demand and dial backup circuits configured on that port to lose connectivity CR 33797 IP Traffic Filters A traffic filters tag violation may occur on a router after you dynamically create a Drop action IP filter CR 33796 IP Traffic Filters Site Manager lets you create IP traffic fil
28. he call locally causing the LCN to be freed However all structures related to the virtual connection VC do not get cleaned up properly As a result any calls placed to this LCN will fail CR 34290 X 25 When you boot a router that has a configuration with a wfLapbPktEntry that is set to Disable X 25 restarts with the following error message X25 System Error DLRESind bad dlc_p pointer CR 34292 X 25 When you set multiple wfLapPktEntry variables to Disable using the Technician Interface and then enter the commit command the router faults in mib_ent c at line 726 CR 34293 X 25 When you disable an X 25 line the log message reports that line 1 is disabled for logical lines on a MCT1 circuit The value 1 is an invalid line number Line numbers are made up of channel type slot module and connector CR 33714 IPEX The server process was disabled with 240 sessions running When the listener process was restarted and the TCP connections had been reestablished the server and router both showed over 280 established connections 26 301894 A Rev 00 Release Notes CR 34295 IPEX The IPEX FSM does not process DATA_IND messages in the Connected CONN state IPEX can now go from the Established EST state to the CONN state and back to the EST state while maintaining active X 25 connections CR 33712 IPEX A PTOP virtual circuit may stop transmitting traffic on the network CR 33715 CR 344
29. he router fails to terminate the Telnet process CR 33330 Learning Bridge Resetting a learning bridge interface results in a bus error when you disable learning bridge globally On an ARE a Vector 2 MCP error can occur 301894 A Rev 00 17 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 19135 Source Route Bridge An enhancement request to produce a new script called show srb traffic filters that would function in the same manner as the show ip traffic filters script CR 32240 X 25 Call requests are always cleared if full addressing is set to OFF CR 33151 IPEX A problem exists between 11 01 and earlier and 11 02 and later implementations of IPEX in which an 11 02 or later router cannot establish calls with an 11 00 router A new MIB parameter wfipexInscallingDte has been added in the IPEX base The default is disabled to prevent the calling DTE address from being added but will allow router software version 11 02 or greater to interoperate with lower revisions of code CR 33379 DLSw ATM Data Direct fails to establish after the ATM link is disrupted CR 32580 Spanning Tree The Spanning tree algorithm fails to converge predictably under failure conditions CR 33181 RSVP The TSpec bucket rate depth and peak rate values get corrupted when the RSVP soloist is running on an ARE processor CR 33653 OSPF The TOS and metric fields in a summary link state update are corrupted
30. ls and release notes free directly from the Internet Go to support baynetworks com library tpubs Find the Bay Networks products for which you need documentation Then locate the specific category and model or version for your hardware or software product Using Adobe Acrobat Reader you can open the manuals and release notes search for the sections you need and print them on most standard printers You can download Acrobat Reader free from the Adobe Systems Web site www adobe com Documentation sets and CDs are available through your local Bay Networks sales office or account representative Bay Networks Customer Service You can purchase a support contract from your Bay Networks distributor or authorized reseller or directly from Bay Networks Services For information about or to purchase a Bay Networks service contract either call your local Bay Networks field sales office or one of the following numbers Region Telephone number Fax number United States and 800 2LANWAN then enter Express Routing 978 916 3514 Canada Code ERC 290 when prompted to purchase or renew a service contract 978 916 8880 direct Europe 33 4 92 96 69 66 33 4 92 96 69 96 Asia Pacific 61 2 9927 8888 61 2 9927 8899 Latin America 561 988 7661 561 988 7550 301894 A Rev 00 vii BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes Information about customer service is also available on the World
31. ltered files data or programs 301894 A Rev 00 iii 4 Limitation of liability IN NO EVENT WILL BAY NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE EVEN IF BAY NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF BAY NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT EXCEED THE PRICE PAID TO BAY NETWORKS FOR THE SOFTWARE LICENSE 5 Government Licensees This provision applies to all Software and documentation acquired directly or indirectly by or on behalf of the United States Government The Software and documentation are commercial products licensed on the open market at market prices and were developed entirely at private expense and without the use of any U S Government funds The license to the U S Government is granted only with restricted rights and use duplication or disclosure by the U S Government is subject to the restrictions set forth in subparagraph c 1 of the Commercial Computer Software Restricted Rights clause of FAR 52 227 19 and the limitations set out in this license for civilian agencies and subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause of DFARS 252 227 7013 for agencies of the Department of Defe
32. n you attempt to configure DOR dynamically a routing update RIP SAP for both IP and IPX problem occurs preventing the exchange of routes with the data packet call CR 33666 DLSw A reserved capx incorrectly returns an error code of DLS_CAPX_INVALID_CTRL_VEC_ID CR 33729 DLSw A VBM error may occur when DLS packets are fragmented in the network 301894 A Rev 00 Release Notes CR 33749 WCP A dial on demand circuit configured with WCP fails to come up when the other end of the circuit is a pre 12 00 router CR 30361 MIB The synchronous external clock speed fails to map over to the MIB II clock speed causing improper aggregation between the internal and external lines CR 33155 SDLC An SDLC connection will be dropped when an ARN router sends a packet before it is polled CR 31684 DLSw Enhancement request to disable DLS multislot broadcasts from the DLC side CR 32854 and 33434 OSPF OSPF sends link state requests LSR when either the retransmit timer activated or a link state update LSU was received Sending an LSR when an LSU was received results in multiple duplicate LSRs CR 31035 ATM When you disable the ATM driver the ATM service record remains in an up state when it should be in a down state CR 32843 Telnet If you Telnet into the router via the ATM LANE port and disconnect abnormally physically remove the Telnet client station off the network without disconnecting Telnet t
33. nd dial backup and hot standby As a result BCP is never negotiated when the dial circuit is established and consequently bridging does not work on that link CR 34527 Boob UNIX Site Manager appears to be querying Relay Agent Preferred Server information incorrectly CR 34039 NAT After you create an unnumbered point to point circuit adding a NAT protocol to this circuit will not create a NAT interface entry instance 30 301894 A Rev 00 Release Notes CR 33887 Statistics Manager The Octets In and Octets Out fields for t_sync dat within Statistics Manager do not get updated after you select Options gt Zero All Counters CR 34239 Router Redundancy An etror occurs in Site manager PC whereby a general protection fault GPF results when you use the edit lines facility from the Edit Circuit window of a router redundant interface CR 34919 CR 35354 PPP When you enable the RFC 1661 Compliance field in the PPP Line List window wfSwservOptsRfc1661Compliance is enabled internally for a dial circuit CR 32366 ATM Site Manager sets the Per VC Clipping parameter to an invalid value when you modify other parameters in the window CR 34819 LLC The LLC circuit pull down option appears to the right of the Help option on the PC instead of to the right of the window pull down option as on the UNIX platform CR 32581 ARE When you click on a slot containing an ARE DS3 or an ARE E3 module
34. nfigured for APPN may fault with tag violations CR 33785 DLSw When you globally disable DLS wfDls wfDlsTotalCircuits 0 shows active DLSw connections wfDls wfDIsTotalCircuits 0 should be set to zero when DLS is disabled CR 33764 APPN Large topology updates may not be completely exchanged when the sending CP is simultaneously receiving multiple updates from a third CP CR 33933 APPN When an EN AS 400 has a large enough number of CP CP sessions the router that receives a Cross_Domain_Initiate GDS variable as a part of EN s LOCATE message incurs a tag violation This problem stems from memory corruption during the allocation and release of buffers in Session Services 20 301894 A Rev 00 Release Notes CR 33700 RSVP A tag violation occurred on a router running Router Software Version 12 00 while starting the soloist CR 33120 Switched Services Routers running software version 11 01 and later send ISDN call setups requesting the same B channel on a PRI for successive calls This condition occurs when attempting to establish multiple dial on demand or dial backup circuits in a short period of time CR 28383 Technician Interface A router experiences random faults and slot resets on an ARE slot while using the Technician Interface CR 34358 Technician Interface If you enter a year other than one between 1971 and 2070 the year will not be set correctly on the router The router accepts only years b
35. nse or their successors whichever is applicable 6 Use of Software in the European Community This provision applies to all Software acquired for use within the European Community If Licensee uses the Software within a country in the European Community the Software Directive enacted by the Council of European Communities Directive dated 14 May 1991 will apply to the examination of the Software to facilitate interoperability Licensee agrees to notify Bay Networks of any such intended examination of the Software and may procure support and assistance from Bay Networks 7 Term and termination This license is effective until terminated however all of the restrictions with respect to Bay Networks copyright in the Software and user manuals will cease being effective at the date of expiration of the Bay Networks copyright those restrictions relating to use and disclosure of Bay Networks confidential information shall continue in effect Licensee may terminate this license at any time The license will automatically terminate if Licensee fails to comply with any of the terms and conditions of the license Upon termination for any reason Licensee will immediately destroy or return to Bay Networks the Software user manuals and all copies Bay Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license 8 Export and Re export Licensee agrees not to export directly or indirectly the Software or
36. onsolidation of the prior bug fixes made through Revision Releases and will roll up all such software bug fixes provided by the recent Revision Releases Year 2000 Compliance BayRS Version 12 01 and Site Manager Software Version 6 01 are Year 2000 Compliance Certified by Bay Networks They have successfully passed Bay Networks Test Procedure which tests conformance to Bay Networks Year 2000 compliance definition both of which can be found at Bay Networks Year 2000 Web Site at http www baynetworks com year2000 Image Builder Operational Note If you are using Image Builder in Site Manager Software Version 6 10 to modify a BayRS Version 12 01 router image you will receive an error Please contact Bay Networks Customer Support to obtain the patch for this problem 2 301894 A Rev 00 Release Notes BayRS Version 12 01 Fixed Anomalies Bay Networks has fixed the following anomalies in Version 12 01 Router Version is managed by Site Manager version v12 01 gt 6 01 v12 00 revision 1 gt 6 00 and 6 00 rev 1 v12 00 revision 2 gt 6 00 and 6 00 rev 2 v12 00 revision 3 gt 6 00 and 6 00 rev 3 CR 34749 DLSw If you delete DLSw from a circuit then you disable DLSw globally a bus error occurs CR 35587 IGMP If you have a static IGMP group it does not age out However if the group receives an IGMP LEAVE mes
37. property Licensee shall not sublicense assign or otherwise disclose to any third party the Software or any information about the operation design performance or implementation of the Software and user manuals that is confidential to Bay Networks and its licensors however Licensee may grant permission to its consultants subcontractors and agents to use the Software at Licensee s facility provided they have agreed to use the Software only in accordance with the terms of this license 3 Limited warranty Bay Networks warrants each item of Software as delivered by Bay Networks and properly installed and operated on Bay Networks hardware or other equipment it is originally licensed for to function substantially as described in its accompanying user manual during its warranty period which begins on the date Software is first shipped to Licensee If any item of Software fails to so function during its warranty period as the sole remedy Bay Networks will at its discretion provide a suitable fix patch or workaround for the problem that may be included in a future Software release Bay Networks further warrants to Licensee that the media on which the Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days from the date Software is first shipped to Licensee Bay Networks will replace defective media at no charge if it is returned to Bay Networks during the warranty period along with proof of
38. py the Software solely for backup purposes in support of authorized use of the Software and c to use and copy the associated user manual solely in support of authorized use of the Software by Licensee This license applies to the Software only and does not extend to Bay Networks Agent software or other Bay Networks software products Bay Networks Agent software or other Bay Networks software products are licensed for use under the terms of the applicable Bay Networks Inc Software License Agreement that accompanies such software and upon payment by the end user of the applicable license fees for such software 2 Restrictions on use reservation of rights The Software and user manuals are protected under copyright laws Bay Networks and or its licensors retain all title and ownership in both the Software and user manuals including any revisions made by Bay Networks or its licensors The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals Licensee may not modify translate decompile disassemble use for any competitive analysis reverse engineer distribute or create derivative works from the Software or user manuals or any copy in whole or in part Except as expressly provided in this Agreement Licensee may not copy or transfer the Software or user manuals in whole or in part The Software and user manuals embody Bay Networks and its licensors confidential and proprietary intellectual
39. rate routes by placing a series of routes in the Advertise list while the Networks list is configured for the 0 0 0 0 0 range all routes CR 34692 IP ISP mode experiences NFS timeouts 8 301894 A Rev 00 Release Notes CR 34809 X 25 When X 25 sends messages to link access protocol balanced LAPB for IPEX in Gateway Mode it occasionally sends them to the incorrect LAPB gate CR 34811 IPEX An error occurs when you bounce Link Access Protocol Balanced LAPB resulting in the following message System error service attempting restart Error in buf_float c at line 113 CR 34816 IPEX Sometimes resets are not being sent because TCP cannot allocate a buffer CR 34817 IPEX In ipex_lapb_gw_send in ipex_data c a message is sent to LAPB if there are no LAPB credits But when the buffer used for this message is then freed a buf float error occurs CR 34843 IPEX LAPB sometimes tries to send a LAPB_CONN_CONF message to IPEX Control Gate before IPEX is loaded if the LAPB client type is not X25 i e IPEX CR 34844 IPEX IPEX s TCP retry feature does not work in the IPEX Gateway Mode over direct LAPB CR 34845 IPEX When running IPEX Gateway Mode over direct LAPB the session comes up but no data is passed CR 26077 BGP If BGP is loaded onto more than one slot or if there is a backup BGP soloist slot configured it will not execute 301894 A Rev 00 BayRS Version 12 01 and Sit
40. s beyond the year 1999 it displays the date as the year 19xx CR 24909 Flash Routers will not boot using Hitachi Maxell type flash cards CR 33798 HW_PROCESSOR The router periodically checks to verify that the I O module has not disconnected from the chassis by sending a signal to a certain pin on the I O module Noise occurring on that pin at the time of the check can cause the signal to be interpreted incorrectly causing the router to generate the following message 816 07 08 97 08 31 03 769 WARNING SLOT MODULE Code 3 I O module has been removed 22 301894 A Rev 00 Release Notes CR 33959 IPEX An enhancement request for the calling address insertion overwrite feature The alarm management system relies on the calling address field in the incoming call to identify the device reporting the alarm The X 25 devices used in this network do not fill the calling address in their calling request packets However the alarm system still works because the public X 25 network inserts the correct calling address when it receives a call request with this field empty A new MIB variable wflpexMappingXlateCallingX121 has been created When wfIpexInsCallingDte is enabled the calling address is overwritten by the value specified in wflpexMapping XlateCallingX121 if configured No CR X 25 Operational Note If you create an X 25 Service entry in dynamic mode you must reboot the router or reset the slot where the newly crea
41. s in Technical Data and Computer Software clause at DFARS 252 227 7013 Notwithstanding any other license agreement that may pertain to or accompany the delivery of this computer software the rights of the United States Government regarding its use reproduction and disclosure are as set forth in the Commercial Computer Software Restricted Rights clause at FAR 52 227 19 Statement of Conditions In the interest of improving internal design operational function and or reliability Bay Networks Inc reserves the right to make changes to the products described in this document without notice Bay Networks Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Portions of the code in this software product may be Copyright 1988 Regents of the University of California All rights reserved Redistribution and use in source and binary forms of such portions are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation advertising materials and other materials related to such distribution and use acknowledge that such portions of the software were developed by the University of California Berkeley The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission SUCH PORTIONS OF THE SOFTWARE ARE PRO
42. sage the static group age time is erroneously set to the configured value and then aged out CR 30266 Frame Relay A bus error can occur in frame relay if a router receives frames destined for a frame relay source route interface while that interface is still initializing 301894 A Rev 00 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34456 Frame Relay A fault may occur when you reboot a router with a configuration that was saved after certain dynamic configuration changes were made to frame relay CR 32296 ARN The ARN U interface Adapter Module will not respond to NT1 loop codes CR 32927 DECnet DECnet sends out an invalid packet which causes other equipment to fail when the packet is received CR 34593 DECnet If you configure a 1 second hello timer on a DECnet interface the router actually transmits a hello packet every 2 07 seconds CR 35156 DECnet The router advertises itself as unreachable when the global RouterLevel is set to level 1 CR 33156 Scripts When you run the show bridge forward script to view the Learning Bridge forwarding table and the table contains 4000 or more entries the slot running the Technician Interface incurs a tag violation error CR 33356 FDDI In a Dual Homed configuration PHY_A disconnects if a process runs too long in the CPU The router reports a PHY_A disconnect and then 50 seconds later will put PHY_A back into standby mode
43. sported across to the remote controller The remote controller responds with an XID Final which is transported back to the central site received by DLSw and by the SDLC code but never transmitted back to the AS 400 CR 33853 DLSw The router faults when the MIB object wfDIsConnectionEntry is aged out CR 33921 SDLC An AN router can experience a bus error fault when you set the SDLC line to VARY ON on the AS400 for the remote SDLC controllers CR 33922 SDLC An AN router may experience a bus error fault when the SDLC is set to VARIED OFF on the AS400 for the remote SDLC controllers 301894 A Rev 00 19 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 33806 IPX The router stops passing IPX NetBIOS traffic in a frame relay group mode hub and spoke environment using NetBIOS static routes with Novell Conformance disabled CR 33778 OSPF When there are multiple ASBRs announcing default routes in their ASEs the Technician Interface lists only one CR 33779 OSPF MOSPF In a fail over test involving Ethernet and FDDI multicast failed to take the correct path through the Ethernet after the FDDI cable was removed However if the Ethernet cable was removed multicast traffic successfully moved to the FDDI link CR 33056 IPX The router fails to apply two IPX filters of equal priority in the order in which they appear in the route filter table CR 33404 APPN A router co
44. t work if you telnet from a Bay Networks router to another Bay Networks router and then telnet to a UNIX station CR 34024 BOT An enhancement request to enable the BayRS Bisync protocol to support more leading SYNC characters Currently the BISYNC code is hardcoded for 2 leading SYNC characters The customer s Bisync controller requires 7 SYNC characters The BayRS code requires configurable leading SYNC characters in order to interoperate CR 34484 PPP IP incorrectly considers the Maximum Receive Unit to include not only the Payload information field but the header as well This can cause a discrepancy in the total packet size crossing the PPP line and the maximum protocol size CR 31530 RDISC A Zero Divide Bus Error occurs when you set the Min and Max Advertisement Interval to the same value when configuring Router Discovery CR 33780 Learning Bridge If you globally disable and then enable learning bridge LB on a slot an error may occur where bridging fails to come back up on that slot CR 34112 DLSw When a router from another vendor sends frames with different circuit ID values to a receiving Bay Networks router the Bay Networks router does not comply to RFC 1795 rules to reflect that the origin circuit ID values are unchanged and not to vary the target circuit ID 301894 A Rev 00 Release Notes CR 34196 MOSPF This is a request to add new Technician Interface IP commands to display DVMRP rou
45. ted entry is configured before the X 25 VC entry will be operational CR 34517 IPEX A problem in the Gateway Mode data flow routine causes calls not to be processed when there is no new data to process This can cause data transfer to stop and never re start for one way traffic CR 34518 IPEX A problem in the Gateway Mode data flow routine causes the TCP window to be updated when data is stored in the data FIFO and by the value of an uninitialized variable The TCP window should only be updated only when data is sent to PLP CR 34524 IPEX When IPEX detects that it received data from X 25 in out of sequence order IPEX should drop the data instead of processing it CR 34525 X 25 Error in PktDATind Q in x25_lirif c causes vc em pointer to be tested for less than zero Pointers are unsigned and are never less than zero 301894 A Rev 00 23 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34519 IPEX The IPEX FSM does not process TCP_RETRY_CONT messages in the Established state CR 34520 IPEX The IPEX FSM does not process PLP_WIN_MSG in the Connected CONN state CR 34526 X 25 When you boot a router with a disabled X 25 line the log message always reports that line 1 is disabled for logical lines on an MCT1 circuit The value 1 is not a valid line number Line numbers are made up of channel type slot module and connector CR 34521 IPEX An error in the IPEX Gate
46. ters Forward to IP Destination Address Forward to Next Hop and Forward to Next Hop Interface but you cannot edit them with Site Manager locally or dynamically CR 33513 Site Manager Admin To change the year on the router to the year 2000 on the Router Date and Time window from the Admin option you move the year slider to 0 Then use the Technician Interface date function to validate that 0 corresponds to 2000 The Router Date and Time window should be changed to accept four digits you should not be expected to know that 0 equals 2000 36 301894 A Rev 00 Release Notes CR 34208 Scheduled Boot A Scheduled Boot should allow the date to be set between 1971 2070 CR 33311 DLSw On Token Ring and Ethernet interfaces Site Manager provides an LLC Interface pull down selection that allows you to select LLC1 or LLC2 From there you can access the DLSw interface definitions This function is missing for ATM Interfaces From the ATM Service Record only the Protocol Add Delete and Edit menus are displayed You cannot access the DLSw interface from the default LLC1 view CR 33667 Source Route Bridging Site Manager should support Source Route Bridging over ATM DXI using RFC 1483 and RFC 1490 encapsulation CR 34152 IP Traffic Filters When reordering the IP traffic filters selecting INSERT AFTER inserts the filter before the precedence number you selected This happens in both dynamic and local mode CR 34033
47. tes and for scheduling calculation CR 34783 Translation Bridge Packets larger than 1500 should be dropped if the translation bridge XB is configured for 802 3 CR 33755 MOSPF This is a request to correct the imported DVMRP routes to AS external type 2 from the current type 1 CR 32983 LOADER If there are two or more advanced routing engines ARE configured in one router and you perform a named boot without specifying the bn exe image or config one of the AREs fails to load all of its executable files CR 34782 IGMP A bus error occurs when a frame relay interface configured with MOSPF fails CR 35039 MOSPF The router fails to reactivate the preferred route from a backbone area to a subnet after restoration of a path that had previously failed CR 35115 X 25 A bus error occurs when tearing down sessions during normal data transfer operations CR 34387 MIB II A multiline multislot sync configuration returns zeroes or inaccurate values for wflfEntry inoctets reported for that circuit 301894 A Rev 00 13 BayRS Version 12 01 and Site Manager Software Version 6 01 Release Notes CR 34704 MOSPF Multicast packets do not get forwarded after a topology change in a redundant network CR 34841 MOSPF Multicast packets do not get forwarded after bouncing a circuit with dual border routers CR 34938 MOSPF When a router is configured for bidirectional traffic and the topology is changed
48. ues as long unsigned integrations No CR PPP When you select PPP Line Lists from the PPP Interface Lists window in dynamic mode Site Manager terminates operation CR 33829 Logical Lines If you deselect the MCT card from the Add Circuit window Site Manager does not allow you to re select it 28 301894 A Rev 00 Release Notes CR 34761 X 25 Site Manager grays out deactivates or disables the Flow Facility parameter on the X25 Service List window for all service types except IPEX CR 34906 Multilink PPP Site Manager does not allow you to modify the Multilink Fragmentation parameter or the Multilink Trigger Size parameter on the PPP Interfaces window CR 34954 AppleTalk The Enable parameter should be the only parameter displayed in the Edit AppleTalk Global Parameters window because MacIP is not supported CR 35261 LLC If you configure DLS LLC on an ATM circuit the LLC1 pull down menu on the Service Record window is missing for that circuit CR 35142 OSPF When you reset the primary OSPF log mask Site Manager resets the OSPF slot mask The slot mask represents on which slots OSPF is eligible to run and the log mask specifies which OSPF errors are written to the log CR 35182 IPEX Adding IPX to or deleting IPX from an 11 02 configuration terminates Site Manager operation CR 33513 Events Manager The events log displays the incorrect date for every year before the leap year CR 35226
49. way Mode routine can occur when data is sent to X 25 to test if there is PLP credit CR 34523 IPEX In IPEX FSM there is a case for IPEX_MSG_POLL_TCP message in 4 states but there is no code that sends that message Also there is no need to poll TCP These cases should be removed CR 34522 IPEX In ipex_pri h there is a define statement that uses an attribute that was deleted dynamically turn on logs through hidden mib parameter define IPEX_DEBUG_LOG_ON ipex_env ipex_env gt init_env gt base_rec gt wflpexMaxSlotSessions 1111 The MIB attribute wfIlpexMaxSlotSessions does not exist CR 33717 FDDI The DA30 was used to send SMT Port Management Request packets to the router The response packet indicated that the long term link error rates on the ports were 10e 8 and 10e 15 The MIB indicated the link error rate to be 10e 15 on both ports 24 301894 A Rev 00 Release Notes CR 34582 X 25 When the VC Gate environment is created for PVCs the vc_state is init to X25_DATAXER This is incorrect because VC is not ready to transfer data VC must wait for a client response message before entering the X25_DATAXER state CR 34583 IPEX When IPEX is in gateway mode and receives a reset when it is in the CONN state it does not verify that the cause code is 09 Operational before switching to the EST state CR 34586 IPEX When IPEX receives a TCP Open request it needs to send a
Download Pdf Manuals
Related Search