Avaya 4600 Series IP Telephones User's Manual
Contents
1. AVAYA Avaya Solution amp Interoperability Test Lab Connecting Avaya 4600 Series IP Telephones and Avaya Wireless LAN Access Points with the HP ProCurve Switch 2626 PWR Inline Power Ethernet Switch Issue 1 0 Abstract These Application Notes describe how to connect and configure Avaya 4600 Series IP Telephones and Avaya wireless LAN access points with the HP ProCurve Switch 2626 PWR Inline Power Ethernet Switch The various Avaya powering arrangements and the administration commands for displaying and controlling the powering status of the switch ports are described SZ Reviewed Solution amp Interoperability Test Lab Application Notes 1 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 1 Introduction Inline power is a feature offered on some Ethernet switches It is a means by which the switch can supply power to a network device within the same cable that carries the Ethernet signaling This simplifies network installation and powering design removing the need for a separate power supply for each IP telephone in the network EEE 802 3af 2003 defines a standard protocol to be used by powering and powered devices The HP ProCurve Switch 2626 PWR is a 26 port 24 10 100Base TX and 2 Gigabit Ethernet switch It supplies its 10 100Base TX ports with 406 watts of power for PoE applications compatible with the IEEE 802 3af standard Avaya 4600 Series IP telephones Avaya wireless LAN access points2. amp Interoperability Test Lab Application Notes 2 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc The powering tests included verification of the following after each product was connected to the switch e Successful boot operation e For IP telephones successful registration with an Avaya Media Server Gateway and successful completion of calls using the IP telephones e g initiate calls receive calls etc e For wireless LAN access points successful registration of a wireless laptop and use of the administration web interface on the access point from the laptop HP ProCurve Switch 2626 PWR POE Switch Avaya AP 5 Access Point Avaya 4602 4602SW IP Telephones Avaya AP 3 EA Access Point Wireless Avaya 4610SW Laptop IP Telephone Avaya 30A Avaya 4620 4 Ethernet Switch 4620SW IP ge Base Telephones with tae Avaya Gen 1 EU24 4612 amp 4624 IP Avaya 4630SW Avaya Gen 2 Telephones IP Screenphone 4606 4612 4624 IP Telephones Figure 1 Avaya 4600 Series IP Telephone and Wireless LAN Access Point Configurations with the HP ProCurve Switch 2626 PWR SZ Reviewed Solution amp Interoperability Test Lab Application Notes 3 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc To line jack of 4612 4624 IP Telephone To Ethernet switch port Figure 2 Avaya 30A Switch Base Connections 2 Equipment and Software Validated The following equipment and software we
3. and the HP ProCurve Switch 2626 PWR comply with this standard These Application Notes show how Avaya IP telephones and wireless LAN access points can be connected to the HP ProCurve Switch 2626 PWR Command line interface CLI commands that display and control powering status of the switch ports are also demonstrated The sample configuration provided in Figure 1 depicts all of the Avaya products that were provided inline power by the HP ProCurve Switch 2626 PWR The following Avaya products are directly connected to the switch e 4602 and 4602SW IP Telephones e 4610SW IP Telephone 4620 and 4620SW IP Telephones including the optional EU24 Button Expansion Module 4630SW IP Screenphone Gen 2 4606 4612 and 4624 IP Telephones Gen 1 4612 and 4624 IP Telephones with 30A Ethernet Switch Base AP 3 and AP 5 Access Points The Gen 1 Avaya 4612 and 4624 IP Telephones require the Avaya 30A Switch Base Figure 2 shows the connections for the 30A switch base The 4612 and 4624 telephones can be identified as Gen 1 or Gen 2 by inspecting the model number 1A in the model number indicates Gen 1 2A indicates Gen 2 The model number can be found by e Inspecting the label attached to the bottom of the telephone OR e Pressing Mute V I E W on the keypad and then pressing until the model number appears Press to exit Examples of model numbers are 4612D01A 003 Gen 1 and 4612D02A 003 Gen 2 SZ Reviewed Solution
4. switch In this example Avaya 4620 4610SW and 4602SW IP telephones were connected to ports 1 3 respectively e Verify that the telephones are powered and booting by inspecting their displays e Check inline power status of the switch ports In the example below all three IP telephones were in the idle state no active calls HP ProCurve 2626 PWR show power management brief Status and Counters Port Power Status Power Cont igured IDS c Sere aoa Power Pone imeveialey Rore thors Status Class Dene eS Sie E E Ue Wn A E E ee OY ee eee cee gee eo ee ene 2 eee ae See ae ae i Yes Critical Delivering 3 2 Yes Critical Delivering 2 3 Yes Cre iaa Delivering 1 4 Yes Low Searching 0 jane ares sf OA Eee SM peer po Sa eke Ges a eee A Sake pone HP ProCurve 2626 PWR show power management 1 3 Status and Counters Port Power Status for port 1 Power Enable Yes Prroni eal SOIC Cal Configured Type Detection Status Delivering Power Class T Over Current Cnt O MPS Absent Cnt l Power Denied Cnt 0 Sen tr eat 0 Voltage a DOOR eh Current 140 mA Power 7000 mW Status and Counters Port Power Status for port 2 Power Enable Yes Priority jy eae eaa Configured Type Detection Status Delivering Power Class 2 Over Cur cent Cnt 0 MPS Absent Cnt 1 Power Denied Cnt 0 SHOES CNE 0 Voltage gt 500 dy Current 67 mA Power 3350 mW Status and Counters Port Power Status for port 3 Power Enable Yes Priority Orea Configured Type Detec
5. ine power ports for use with Avaya IP telephones and wireless APs I Attach a serial cable to the console of the HP ProCurve Switch 2626 PWR and log in A user name and password are not required to log in unless the user name and password are pre set ProCurve 2626 PWRsenable ProCurve 2626 PWR 2 Enter configuration mode Enable inline power on all ports ProCurve 2626 PWR config t ProCurve 2626 PWR config interface 1 24 power ProCurve 2626 PWR config exit ProCurve 2626 PWR conf 19g For example to set inline power priority to critical for ports 1 3 use the following command ProCurve 2626 PWR config interface 1 3 power critical ProCurve 2626 PWR config exit For example to disable inline power for ports 10 15 use the following command HP ProCurve 2626 PWR config no interface 10 15 power HP ProCurve 2626 PWR config exit After the execution of the above commands ports 4 9 and 16 24 are still inline power enabled with low priority status as defined by the first command interface 1 24 power Since the inline power commands can be applied to an individual port or a range of ports users have the flexibility to assign switch ports with different power status according to their needs SZ Reviewed Solution amp Interoperability Test Lab Application Notes 6 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 2 e Connect several Avaya IP Telephones as shown in Figure 1 to Ethernet ports on the
6. mp Interoperability Test Lab at SZ Reviewed Solution amp Interoperability Test Lab Application Notes 10 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc
7. plication Notes 8 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 6 Conclusion The following Avaya IP telephone and wireless LAN access point products were tested with the HP ProCurve Switch 2626 PWR and were successfully powered e IP telephones 4602 and 4602S W 4610S W 4620 and 4620SW including EU24 Button Expansion Module 4630S W Gen 1 4612 and 4624 with 30A switch base Gen 2 4606 4612 and 4624 e Wireless LAN access points e AP3 e AP5 SZ Reviewed Solution amp Interoperability Test Lab Application Notes 9 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 2004 Avaya Inc All Rights Reserved Avaya and the Avaya Logo are trademarks of Avaya Inc All trademarks identified by and are registered trademarks or trademarks respectively of Avaya Inc All other trademarks are the property of their respective owners The information provided in these Application Notes is subject to change without notice The configurations technical data and recommendations provided in these Application Notes are believed to be accurate and dependable but are presented without express or implied warranty Users are responsible for their application of any products specified in these Application Notes Please e mail any questions or comments pertaining to these Application Notes along with the full title name and filename located in the lower right corner directly to the Avaya Solution a
8. re used for the sample configuration provided Equipment l Avaya 4624 IP Telephone Gen 2 0 Avaya 30A Ethernet Switch Base _ _ o oS d Avaya 4612 IP Telephone Gen 1 Gen 2 1 0 8 8 Table 1 Equipment and Software Validated SZ Reviewed Solution amp Interoperability Test Lab Application Notes 4 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 3 HP ProCurve Switch Inline Power Commands This section describes the commands that can be issued to monitor and control inline power status of the switch ports Note that by default inline power for all ports is enabled The commands are listed below with a brief description by default of their application Examples of their use can be found in Section 4 The CLI commands applicable to inline powering of ports are interface lt port list gt power can be used on a port or ports to enable inline powering The powered device PD will receive power automatically when it is plugged into the switch port and presents the maintain power signature Note the key word port list can be either an individual port or a range of ports interface lt port list gt power critical high low assigns the port ports with different priority levels on power supply a Critical The switch supplies active PoE support at this level before PDs connected to High or Low priority ports b High The switch supplies active PoE support at this level before PDs connec
9. ted to Low priority ports c Low the default The switch supplies active PoE support at this level only if there is power available after supplying active PoE support to ports at the higher priority levels no interface lt port list gt power removes power from and disables automatic powering of the connected device Note that disabling a port that has inline power activated only disables its network connection not the inline power power threshold lt 99 gt sets the power consumption percentage at which a trap should be sent The range 1s 1 99 and the default setting is 80 Show power management brief shows summary of power status for all ports with information on power enable status power priority detection status and power class show power management lt port list gt displays the powering status of the ports defined by the key word port list In addition to the information provided by the command show power management brief the actual power consumed by each telephone and the power priority are displayed as well Table 2 shows the required power allocations defined by IEEE 802 3af 2003 based on the class Class Usage 0 Default 15 4 Table 2 IEEE 802 3af Power Classes SZ Reviewed Solution amp Interoperability Test Lab Application Notes 5 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 4 Configure Inline Power Ports The following CLI session demonstrates configuration and status of inl
10. tion Status Delivering Power Class i Over Current Cne 0 MPS Absent Cnt 0 Power Denied Cnt 0 SOs th eat 0 Voltage 500 dV Current 64 mA Power 3200 mW SZ Reviewed Solution amp Interoperability Test Lab Application Notes 7 of 10 WCH 3 18 2004 2004 Avaya Inc All Rights Reserved HP PoE doc 5 Verification Steps The following steps can be used to verify proper connection configuration and powering of Avaya IP telephones I e Disable inline power to port and verify that the telephone loses power HP ProCurve 2626 PWR config no interface 1 power HP ProCurve 2626 PWR show power management brief Status and Counters Port Power Status Power Configured Detection Enable Priority Type Status Critical Disabled Critical Delivering Oricrecal Delivering Searching Note that the Power Enable column is set to No and the Detection Status column indicates that inline powering is disabled for port 1 2 Enable inline power for port 1 and verify that the telephone receives power HP ProCurve 2626 PWR config interface 1 power HP ProCurve 2626 PWR config exit HP ProCurve 2626 PWH show power management 1 Status and Counters Port Power Status for port 1 Power Enable Yes Prrority Low Configured Type Detection Status Delivering Power Class Over Current Cnt 0 MPS Absent Cnt Power Denied Cnt 0 Sine ie OnE Voltage 2 See env Current Power 7000 mW SZ Reviewed Solution amp Interoperability Test Lab Ap
Download Pdf Manuals
Related Search