Avaya 4600 Series IP Telephones Application Note
Contents
1. interfac thernet 1 22 port name SINGLE LINK j interface ethernet 1 23 link aggregate active interface ethernet 1 24 link aggregate active interface ve 9 Create a virtual interface for each VLAN ip address 9 9 9 101 255 255 255 0 ip helper address 1 192 168 50 100 ip ospf area 0 interface ve 10 ip address 10 10 10 101 255 255 255 0 ip helper address 1 192 168 50 100 ip ospf area 0 GAK Reviewed Solution amp Interoperability Test Lab Application Notes SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved 7 of 12 superxpoe Use the command sh inline power to view inline power statistics on each port Power Capacity Total is 1080000 mWatts Current Free is 915200 mWatts Power Allocations Requests Honored 45 times Port Admin Oper Power mWatts PD Type PD Class Pri Fault State State Consumed Allocated Error 1 1 On On 7230 15400 802 3af Class 3 3 n a 1 2 On On 5070 7000 802 3af Class 2 3 n a 1 3 On On 3004 7000 802 3af Class 2 3 n a 1 4 On On 4882 7000 802 3af Class 2 3 n a 1 5 Off Off 0 0 n a n a 3 n a 1 6 On On 6854 15400 802 3af Class 3 3 n a 1 7 On On 2723 4000 802 3af Class 1 3 n a 1 8 On On 4601 15400 802 3af n a 3 n a 1 9 On On 5070 15400 802 3af Class 3 3 n a 1 10 On On 4789 15400 802 3af n a 3 n a 1 11 On On 3098 7000 802 3af Class 2 3 n a 1 12 On On 4695 15400 802 3af n a 3 n a 1 13 Off OFE 0 0 n a n a 3 n a 1 14 On On 302. Solution amp Interoperability Test Lab Application Notes 10 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 6 Support For technical support on Foundry Networks products contact the Technical Support Center using any of the following options Toll free 1 877 TURBOCALL 1 877 887 2622 Direct 408 586 1881 Email support foundrynet com 7 Conclusion These Application Notes describe the steps for configuring the Foundry Networks FastIron Super X Switch to provide inline Power over Ethernet PoE to the Avaya PDs namely Avaya IP Telephones and Avaya Wireless Access Points During compliance testing the Avaya PDs simultaneously obtained power and transferred data over standard Ethernet cables from the Foundry Networks FastIron Super X Switch 8 Additional References e Product documentation for Avaya products may be found at http support avaya com e Product documentation for Foundry Networks products may be found at http www foundrynet com GAK Reviewed Solution amp Interoperability Test Lab Application Notes 11 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 2006 Avaya Inc All Rights Reserved Avaya and the Avaya Logo are trademarks of Avaya Inc All trademarks identified by and are registered trademarks or trademarks respectively of Avaya Inc All other trademarks are the property of their respective owners The information provided in these Application Note
3. differentiated by the microphone at the bottom right side of the telephone If the microphone has one hole it is Class 2 and if it has two holes it is Class 3 Powered device classifications of the phones are defined by the Institute of Electrical and Electronics Engineers IEEE 802 3af Each Powered Device is classified into one of the IEEE s five classes The IEEE 802 3af PSE and Powered Device Power Classifications chart can be seen in Table 2 The powering tests included verification of the following after the product was connected to the switch e Successful boot operation e For Avaya IP Telephones successful registration with Avaya Communication Manager or Avaya IP Office for the Avaya 5600 Series IP Telephones completion of a test call and raising speakerphone volume to maximum value e For the Wireless Access Point successful registration of a wireless enabled Avaya IP Softphone with Avaya Communication Manager and completion of a test call e Connecting a mix of 22 Avaya IP Telephones and an Avaya AP 8 Wireless Access Point to the switch power cycling the switch and verifying successful boot operation and registration of the devices to Avaya Communication Manager and Avaya IP Office Small Office Edition Avaya IP Softphone Avaya 4601 and Avaya IP Office Avaya S8300B Media Server specific 5601 IP Telephones with Avaya G350 Media Gateway Avaya AP 8 Avaya IP Office Small LO Access Point Ofice Editon mE
4. 04 4000 802 3af Class 1 3 n a 1 15 On Off 0 0 n a n a 3 n a 1 16 On On 3098 7000 802 3af Class 2 3 n a 1 17 On On 1784 7000 802 3af Class 2 3 n a 1 18 On On 2817 7000 802 3af Class 2 3 n a 1 19 On On 4131 15400 802 3af n a 3 n a 1 20 Off Off 0 0 n a n a 3 n a 1 21 Off Off 0 0 n a n a 3 n a 1 22 Off Off 0 0 n a n a 3 n a 1 23 Off Off 0 0 n a n a 3 n a 1 23 Off Off 0 0 n a n a 3 n a Total 66850 164800 Grand Total 66850 164800 GAK Reviewed Solution amp Interoperability Test Lab Application Notes 8 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 4 Interoperability Compliance Testing The interoperability compliance testing focused on verifying PoE interoperability between the Foundry Networks FastIron Super X switch and Avaya IP Telephones and Avaya AP 8 Wireless Access Point 4 1 General Test Approach The general test approach was to connect the Avaya PDs Avaya IP Telephones and Avaya AP 8 Wireless Access Point to PoE enabled ports on the Foundry Networks FastIron Super X switch and verify that the PDs successfully boot To verify that power and data can be simultaneously carried on the PoE connections phone calls were made from the IP Telephones to and from Avaya IP Softphone operating from a wireless laptop accessing the network via the AP 8 4 2 Test Results All Power over Ethernet test cases completed successfully The Foundry Networks FastIron Super X switch successfully provided inline power to the A
5. AVAYA Avaya 4602 4602SW amp Avaya IP Office specific 5602SW IP Telephones Foundry Networks Fastlron Super X Switch SFeSsesssese j Avaya 4622SW z IP Telephone Ye em om eee Fete Samet Avaya 4610SW amp Avaya IP Office specific 5610SW IP Telephones Avaya 4606 4612 and 4624 Gen 2 IP Telephones Avaya 4625SW Avaya 4620 4620SW amp bes Petephone 4621SW IP Telephones DHCP Server Figure 1 PoE Interoperability Between Foundry Networks FastIron Super X Switch and Avaya IP Telephones and Avaya Wireless Access Points GAK Reviewed Solution amp Interoperability Test Lab Application Notes 3 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 2 Equipment and Software Validated The following equipment and software firmware were used for the sample configuration provided Equipment Software Firmware Avaya S8300 Media Server in a G350 Media Gateway 3 0 1 load 346 Avaya IP Office Small Office Edition 3 0 55 Avaya 4601 IP Telephone 1 8 0 Avaya 4602 IP Telephone 1 8 2 Avaya 4602SW IP Telephone 2 3 Avaya 4610SW IP Telephone 2 3 Avaya 4620 IP Telephone 2 3 Avaya 4620SW IP Telephone 2 3 Avaya 4621SW IP Telephone 2 3 Avaya 4622SW IP Telephone 2 3 Avaya 4625SW IP Telephone 2 5 Avaya 4630SW IP Telephone 1 810 Avaya 5601 IP Telephone IP Office specific 1 806 Avaya 5602SW IP Telephone IP Offi
6. AVAYA Avaya Solution amp Interoperability Test Lab Application Notes for Foundry Networks FastIron Super X Power over Ethernet PoE Switch with Avaya IP Telephones and Avaya Wireless Access Points Issue 1 0 Abstract These Application Notes describe the procedures for configuring the Foundry Networks FastIron Super X switch to provide inline Power over Ethernet PoE to Avaya IP Telephones and Avaya Wireless Access Points During compliance testing Avaya IP Telephones and Wireless Access Points successfully obtained power and transferred data over standard Ethernet cables from a Foundry Networks FastIron Super X switch Information in these Application Notes has been obtained through compliance testing and additional technical discussions Testing was conducted via the DeveloperConnection Program at the Avaya Solution and Interoperability Test Lab GAK Reviewed Solution amp Interoperability Test Lab Application Notes 1 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 1 Introduction Power over Ethernet PoE allows both power and data to be simultaneously carried over standard Ethernet cables PoE enabled Ethernet switches can supply power directly to Ethernet devices thereby simplifying installation and removing the need for separate power supplies for those devices The IEEE 802 3af standard defines the mechanisms for Power Sourcing Equipment PSE such as PoE enabled Ethernet switches to detect class
7. ce specific 2 2 3 Avaya 5610SW IP Telephone IP Office specific 223 Avaya 5620SW IP Telephone IP Office specific 2 2 3 Avaya Gen 2 4606 IP Telephone 1 8 3 Avaya Gen 2 4612 IP Telephone 1 8 3 Avaya Gen 2 4624 IP Telephone 1 8 3 Avaya AP 8 Wireless Access Point 2 6 0914 Avaya IP Softphone 5 2 3 6 Foundry Networks FastIron Super X Switch 2 4 00 Table 1 Equipment and Software Firmware GAK Reviewed Solution amp Interoperability Test Lab Application Notes 4 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe 3 Configure the Fastlron Super X Switch Inline Power over Ethernet PoE is supported on the Foundry Networks Super X Switch By default PoE support is disabled on all the 10 100 1000 BaseT ports Power over Ethernet can be configured on the 24 port gigabit copper module via the browser interface or command line interface CLI The following configuration file was provisioned using the Foundry CLI Current configuration ver 02 4 00T3e3 module 1 fi sx4 24 port gig copper modul module 9 fi sx4 12 combo port management modul l global stp vlan 1 name DEFAULT VLAN by port spanning tree 802 lw vlan 10 by port tagged ethe 1 1 to 1 4 ethe 1 6 to 1 7 ethe 1 9 ethe 1 11 ethe 1 17 ethe 1 22 to 1 24 untagged ethe 1 19 router interface ve 10 Map Virtual Engine s to VID s ex Ve 10 to VLAN 10 spanning tree 802 1 spanning tr 802 spanning tr 802 spanning tr 802 s
8. ged frames to and from attached devices on VLAN 9 including both directly or indirectly attached PCs Enable 802 1AF inline power for applicable ports j interfac thernet 1 2 port name 4621SW dual mode 9 inline power 1 interfac thernet 1 3 port name 4610SW dual mode 9 inline power 1 interfac thernet 1 4 port name 4622SW dual mode 9 inline power 1 interfac thernet 1 5 1 interfac thernet 1 6 port name 4620IP dual mode 9 inline power interfac thernet 1 7 port name 4602IP dual mode 9 inline power 1 interfac thernet 1 8 port name 4624IP inline power interface ethernet 1 9 port name 4620SW dual mode 9 inline power interface ethernet 1 10 port name 46121P inline power interfac thernet 1 11 GAK Reviewed Solution amp Interoperability Test Lab Application Notes 6 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe port name 4602SW dual mode 9 inline power interface ethernet 1 12 port name 4606IP inline power interface ethernet 1 13 port name IP Office interface ethernet 1 14 port name 5602SW inline power interfac thernet 1 15 inline power interface ethernet 1 16 port name 5610SW inline power interfac thernet 1 17 port name 46011IP dual mode 9 inline power interfac thernet 1 18 port name 56011IP inline power interface ethernet 1 19 port name AP8 inline power
9. he Foundry Networks FastIron Super X switch indicates Class 0 as n a in the CLI 5 Verification Steps The following steps were used to verify the configuration 1 2 Ensure that PoE has been enabled on the Foundry Networks FastIron Super X switch and the ports that serve the PDs Connect the Avaya PD to a PoE enabled port on the Foundry Network FastIron Super X switch and verify that the PD powers on successfully If the PD does not power on enter the command sh inline power to confirm PoE is enabled on the port Verify that the Avaya 4600 Series IP Telephones successfully register with Avaya Communication Manager and complete phone calls to other phones assumes the IP telephones have been configured with the correct IP and call control information Verify that the Avaya 5600 Series IP Telephones successfully register with Avaya IP Office and complete phone calls to other phones assumes the IP telephones have been configured with the correct IP and call control information Verify the Avaya Wireless Access Point by having an Avaya IP Softphone running on a wireless laptop accessing the network via the Access Point successfully register with Avaya Communication Manager and complete phone calls to other phones assumes the IP Softphone has been configured with the correct IP and call control information Verify the Avaya IP Telephone continues to function properly when the speakerphone volume is turned up to max value GAK Reviewed
10. ify and supply power to Powered Devices PDs such as PoE enabled IP telephones and wireless access points In the compliance tested configuration described in these Application Notes a Foundry Networks FastIron Super X Switch has a PSE configured to supply inline PoE to Avaya PDs specifically Avaya IP Telephones and an Avaya AP 8 Wireless Access Points As illustrated in Figure 1 the Avaya PDs covered in these Application Notes include the following 4601 IP Telephone 4602 IP Telephone 4602SW IP Telephones 4610SW IP Telephone 4620 IP Telephone 4620SW IP Telephone 4621SW IP Telephone 4622SW IP Telephone 4625SW IP Telephone 4630SW IP Telephone 5601 IP Telephone 5602SW IP Telephone 5610SW IP Telephone 5620SW IP Telephone Avaya Gen 2 4606 4612 and 4624 IP Telephones Avaya Wireless AP 8 802 1 1a b g Access Point The Avaya 4612 and 4624 IP Telephones can be identified as Gen 2 by inspecting the model number 2A in the model number indicates Gen 2 The model number can be found by e Inspecting the label attached to the bottom of the telephone OR e Pressing Mute V I E W on the keypad and then pressing until the model number appears Press to exit An example of a model number is 4612D02A 003 Gen 2 GAK Reviewed Solution amp Interoperability Test Lab Application Notes 2 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe The Avaya 4620SW Class 2 and Class 3 IP Telephones can be
11. panning tr 802 spanning tr 802 spanning tr 802 spanning tr 802 spanning tr 802 spanning tr 802 spanning tr 802 the 1 1 admin edge port the 1 2 admin edge port the 1 3 admin edge port the 1 4 admin edge port the 1 7 admin edge port the 1 9 admin edge port the 1 11 admin edge port the 1 22 path cost 50000 admin pt2pt mac the 1 23 admin pt2pt mac the 1 24 admin pt2pt mac SS SES E E28 vlan 9 by port tagged ethe 1 1 to 1 4 ethe 1 6 to 1 7 ethe 1 9 ethe 1 11 ethe 1 17 ethe 1 22 to 1 24 router interface ve 9 spanning tree 802 1w spanning tr 802 1w ethe 1 1 admin edge port spanning tr 802 1w ethe 1 2 admin edge port spanning tr 802 1w ethe 1 3 admin edge port spanning tr 802 1w ethe 1 4 admin edge port spanning tr 802 1w ethe 1 7 admin edge port spanning tr 802 lw ethe 1 9 admin edge port spanning tr 802 lw ethe 1 11 admin edge port spanning tr 802 1w ethe 1 22 path cost 50000 admin pt2pt mac spanning tr 802 1w ethe 1 23 admin pt2pt mac spanning tr 802 lw ethe 1 24 admin pt2pt mac GAK Reviewed Solution amp Interoperability Test Lab Application Notes 5 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe f l hostname SuperX router ospf area 0 l interfac thernet 1 1 Optionally define a port name Enable dual mode support In this case ethe 1 1 will accept and transmit untag
12. s is subject to change without notice The configurations technical data and recommendations provided in these Application Notes are believed to be accurate and dependable but are presented without express or implied warranty Users are responsible for their application of any products specified in these Application Notes Please e mail any questions or comments pertaining to these Application Notes along with the full title name and filename located in the lower right corner directly to the Avaya DeveloperConnection Program at devconnect avaya com GAK Reviewed Solution amp Interoperability Test Lab Application Notes 12 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe
13. vaya PDs Table 2 below lists the 802 3af class allocated power and measured power of the Avaya PDs when connected to the Foundry Networks FastIron Super X switch The measured power listed is for the particular phone being tested Avaya Powered Device 802 3af Allocated Measured Power Observations Class Power W mW Idle Spkr max vol 4601 2 7 1784 See Note 1 4602 1 4 2123 2817 4602SW 2 7 3098 4000 4610SW 2 7 3004 3756 4620 3 15 4 6854 7314 4620SW Post 11 2004 2 7 4882 6667 4621SW 2 7 5070 4622SW 2 7 4882 5915 4625SW 3 15 4 7230 8400 5601 2 7 2817 See Note 1 5602SW 1 4 3004 5610SW 2 7 3098 Gen 2 4606 n a 15 4 4695 5153 See Note 2 Gen 2 4612 n a 15 4 4789 5216 See Note 2 Gen 2 4624 n a 15 4 4601 5101 See Note 2 AP 8 n a 15 4 4131 Table 2 802 3af Class Allocated Power and Measured Power for Avaya IP Telephones and Wireless Access Point connected to Foundry Networks FastIron Super X Switch GAK Reviewed Solution amp Interoperability Test Lab Application Notes 9 of 12 SPOC 3 16 2006 2006 Avaya Inc All Rights Reserved superxpoe Table 3 below summarizes the 802 3af classes Class PSE Output Max Power W 0 15 4 1 4 0 2 7 0 3 15 4 4 Treat as Class 0 Table 3 IEEE 802 3af PSE and Powered Device Power Classifications Note 1 The 4601 and 5601 IP Telephones do not have a speakerphone button Note 2 T
Download Pdf Manuals
Related Search