Auto Page RS-8601cd User's Manual
Contents
1. AUTOPAGE RS 860 cd PROFESSIONAL REMOTE CAR STARTER WITH ALARM SYSTEM amp 2 WAY LCD COMMUNICATION OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY TABLE OF CONTENTS A REMOTE TRANSMITTER 4 B BATTERY REPLACEMENT 5 C THE REMOTE LCD ICONS WITH FUNCTION 6 C PROGRAMMING OF THE LCD REMOTE TRANSMITTER 7 Screen Lamp ON Power Save Mode Clear The Flash Icon and Melody Sound otop The Melody Sound Button Lock Vibration Melody Mode Enable Disable Bi Sound While Pressing Button Low Battery Indication Set Up Fixed Count Down Timer 10 Out Of The Range Check D CEOCK amp TIMER SETTING 8 1 Timer Setting 2 Alert Alarm Timer Setting 3 Count Down Timer Setting 4 Time Set Up For Daily Timer Start A REMOTE TRANSMITTER OPERATION 11 BUTTON LOCK 12 C LED DISPLAY 13 D CHIRP INDICA TOR cis 13 E PARKING EIGHT 22 d MA E RD SN REM MM MEET ERE 13 F ALARM OPERATION CONDITION 13 ACTIVE ARMING ARM amp LOCK 13 Defective Sensor Reminder Silent Arming Disarming Shock Sensor By Pass H PASSIVE ARMING 14 Passive Arming with Passive Door Locking Passive Arming By Pass2. ACTIVE DISARMING UNLOCK amp DISARM 14 Tamper Disarming Pathway lllumination Two Steps Door Unlock Automatic Re Arm J DISARMING WITHOUT A TRANSMITTER 15 Overrides the Alarm without Password Pin Code Overrides the Alarm With Password Pin Code K VALET MODE ura aci ia 16 Enter Valet Mode Exit Valet Mode LOCATOR Pu PEN Dex Vu 16 PANIC FUNCTION codes 16 N TRIGGER IHE SYSTEM Ense 17 Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement Circuit ANTI CAR JACKING 18 Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking P SYSTEMS TRIGGER CHECK 19 OQ SYSTEMS STATUS CHECK ia 19 R DRIVER PAGING OPTION eere 19 S DOME LIGHT CONVENIENCE DELAY amp SUPERVISION 20 T IGNITION CONTROL THE DOOR LOCK UNLOCK 20 TRUNK RELEASE CHANNEL 3 OUTPUT 20 V CHANNEL 4 TIMER CONTROL OUTPUT 20 W CHANNEL 5 TIMER CONTROL OUTPUT 20 X CHANNEL 6 TIMER CONTROL OUTPUT 20 Y SECOND VEHICLE SECURITY OPERATION 21 Z
3. Autopage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service Please keep this card in a secured place AUTOPAGE WARRANTY SERVICE CARD Model Serial CUSTOMER TO COMPLETE DEALER TO COMPLETE Mr Mrs Ms Your Name Please Print Company Name Address Dealer s Address City State Zip Code City State Zip Code Telephone Number Dealer s Telephone Number Year Make Model of Vehicle Date of Installation Purchase Dealer s Signature Proof of Purchase which includes the store name and date of purchase must accompany all warranty returns It is the purchaser s responsibility to keep this card for any future warranty service 27 AUTOPAGE UY 960 Knox Street Unit B Torrance California 90502 Main Office 310 323 1800 Customer Service 800 262 2527 Ext 462 www autopageusa com 28
4. Enable Disable Bi Sound While Pressing Button It has a short bi sound while pressing the button of the LCD screen transmitter If you want mute the sound mute always while press button Press the SET button first within 3 seconds press and hold the Bi button for 2 seconds to disable the bi sound 8 Low Battery Indication When the power of the battery weakens it has two short bi sound and flash icon while pressing the button of the LCD screen transmitter 9 Set Up Fixed Count Down Timer 1 Press the SET button first within 3 seconds press and hold the O 2 icon and timer i e 0 10 or button for 2 seconds the LCD screen will shows 2 Press the 69 button again showing next order time on the screen ie 0 20 press them again ie 0 30 and so on ffe 3 Leave the buttons starting count down then 2 icon flashes Note 1 The count down period is fixed as 10 minutes 20 minutes 30 minutes 1 hour 1 5 hours and 2 hours maximum a When count down timer showing 0 00 means to turn off the timer Press SET button for real time indication when the timer is counting down 10 Out Of Range Indication 1 If within the range the icon will display on the LCD screen 2 If you are out of range the icon will disappear on the LCD screen D CLOCK amp TIMER SETTING Press Transmitter 1 Press amp Hold the 9ET Clock Setting Hour for and fo
5. 3 seconds Shock Sensor Silent Arming Disarming Ignition in off position Ignition in on position press and hold for Active Anti Car Jacking Mode System Two Steps Door Unlock amp Press twice within 3 seconds Disarm System Trunk Release Channel 3 Press and Hold for 2 seconds Passive Arming By pass While the system Disarmed Press within 3 seconds and Hold Button Lock a button for 2 seconds a Arm System and Hidden Under disarm mode press within 3 Alarm Function seconds and Hold button Activate or Turn Off The Remote Start Press twice within 3 seconds 11 LCD DISPLAY TRANSMITTER OPERATION ONLY System Function System s Trigger Record we SET C Check Press within 3 seconds System s Status Check Press within 3 seconds Press within 3 seconds and Button Lock Hold fal button for 2 seconds Optional Driving Pager Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds V Daily Timer Start Press within 3 seconds LCD screen lamp turns on for Press and hold for 1 second Clear the Flash Icon and SET SET SET Melody Sound on the LCD Press within 3 seconds Screen Transmitter Warning Press the K button two times when the battery compartment is empty then insert the new battery B BUTTON LOCK It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by
6. melody sound on the LCD screen transmitter STOP THE MELODY SOUND ONLY While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon press any button on the LCD remote transmitter to stop melody sound only NOISE ABATEMENT CIRCUIT You system has Noise Abatement Circuit It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder jackhammers airport noise etc Here s how Noise Abatement Circuit works The alarm triggers 3 times Each time the same sensor or switch is triggering the alarm Noise Abatement 17 Circuit will interpret this pattern of triggers as false alarm After the third trigger Noise Abatement Circuit ignores or bypasses that sensor or switch until the other sensor or switch 15 trigger Noise Abatement Circuit covers doors Hood Trunk differently If the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trigger ceases O ANTI CAR JACKING Warning If you don t need the car jacking function in this alarm system be sure to set car jacking feature OFF This system is default setting all car jacking OFF ACTIVE ANTI CAR JACKING 1 Press and hold the transmitter s and ES button at the same time for 2 seconds while the vehicle s ignition is ON The parking lights will turns on for 1 5 seconds to indicate this enter 2 On
7. or garage Always apply the parking brake and lock the vehicle as you exit the vehicle The vehicle windows must be rolled up Should the unit malfunction disconnect the fuse until the problem is corrected 8 The use and operations of this system is the sole responsibility of the operator 9 Some areas may have local ordinances that prohibit leaving a vehicle running on public streets 10 Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place NO 01 B W PO LCD REMOTE CONTROL TRANSMITTER WT I Note If the system is interfered by stronger radio frequency around sources of high voltage electric power or such Obstacles like tall buildings and so on the transmission range may get shorter as the system uses low out put powered frequency A BATTERY REPLACEMENT A 1 5V type AAA Alkaline battery powers the Remote Transmitter When the power of the battery weakens icon shall be displayed on the LCD screen When the old battery is replaced to new one there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12 00 after displaying all the icons Correct the time by pressing SET for 3 seconds before using See Timer Setting p A BATTERY REPLACEMENT T M ME ro co E Remove screw from back of E fy XT 85s Transmitter Open case V MI d N Cr gee t Ji to e
8. ON MEMORY This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected 21 REMOTE START OPERATION A TO REMOTE START THE VEHICLE When you want to start your vehicle Activate Remote 1 Press button once on the transmitter Start 2 The parking light will activate to indicate the remote start received the signal 3 The engine will start approximately 5 seconds 4 Once the engine is running after couple seconds the parking light will turn on again and climate controls will activate and adjust the vehicles interior temperature to your preset setting While the vehicle is running the minutes digit on the LCD screen will flash and the will indicate count down timer based on the 5 10 20 or 30 minute run time set up by your installation center 5 The vehicle will run for 5 to 30 minute cycle automatically shut down When the unit shuts off the count down timer will turn off and the transmitter will play a melody E The Remote Start Unit will not start the vehicle if any one of the following conditions exists 1 The hood is opened 2 The brake pedal is pressed 3 Move the optional remote start enable toggle switch to OFF position If installed 4 The gear selector is in any gear other then PARK or NEUTRAL Engine Running SAFE START Child safety mode Factory defaults setting to press the button twice on the transmi
9. POWER ON MEMORY 21 REMOTE START OPERATION A TO REMOTE START THE VEHICLE 22 Safe Start Child safety mode B TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE jpg on a a 22 TEMPORARY STOP FEATURE 22 D TURBO TIMER START FEATURE 23 E TIMER TEMPERATURE START 23 3 Hours Timer Start With Temperature Control Off 3 Hours Timer Start With Temperature Control Daily Timer Start Exit the Timer Start TEMPERATURE CHECK 24 G TO TURN OFF THE REMOTE START 24 SHUT DOWN INPUT FOR REMOTE STARTER 24 I DISABLING THE REMOTE START SYSTEM 25 WARRANTY 55 26 WARRANTY 27 WARNINGS As with any product that performs automatic functions there are certain safety precautions that you must practice and be aware of 1 Keep the transmitter out of children s reach Do not leave anyone in the vehicle while running on remote control Alert servicing personnel that the vehicle can be started automatically Do not start the vehicle by remote while it s in an enclosed area
10. ce the system is armed If you are forced from the vehicle the system will trigger when the door is opened and closed while the ignition is ON PASSIVE ANTI CAR JACKING It operate as below 1 Turn the ignition switch to the ON position the system will arm 2 Once the system is armed If you are forced from the vehicle the system will trigger when the door is opened and closed while the ignition is ON TRIGGER THE ANTI CAR JACKING MODE 3 timer circuits will function as follows First timer a 50 seconds after the system has been triggered The siren will start chirping for 15 seconds b During this 15 seconds period of chirping you will be alerting to push the valet switch once to turn off the car jacking feature If not it will enter second timer car jacking Second timer 65 seconds after the system has been triggered The siren starts alarming and the parking light starts flashing Third timer 90 seconds after the system has been triggered a The siren still alarming and the parking light flashing and b The starter disable will activate to prevent the vehicle from starting C It will remain active until the vehicle s battery power exhausted OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR JACKING Turn the ignition switch from OFF to ON and within 10 seconds push valet switch the siren will stop and the system disarmed Note If you use password pin code to double protect the vehicle security you will n
11. e duration from 1 second to 120 seconds For instance this timer output may be used to turn on the headlight power window or sunroof Factory defaults setting at momentary output W CHANNEL 5 TIMER CONTROL OUTPUT Press the transmitter 5 and 5 buttons at the same time to active Channel 5 function Channel 5 is user programmable timer output You may program the built in timer to send a ground signal for any time duration from 1 second to 120 seconds For instance this timer output may be used to turn on the headlight power window or sunroof Factory defaults setting at momentary output X CHANNEL 6 TIMER CONTROL OUTPUT Press the transmitter 6 6 buttons at the same time to active Channel 6 function Channel 6 is user programmable timer output You may program the built in timer to send a ground signal for any time duration from 1 second to 120 seconds For instance this timer output may be used to turn on the headlight power window or sunroof Factory defaults setting at momentary output 20 Y SECOND VEHICLE SECURITY OPERATION Your 5 button remote transmitter can be utilized to control a second vehicle security system To program the remote control transmitter to a second vehicle follow the instructions for Transmitter programming Programming the Transmitter to 2 Car Enter 1 Turn the ignition key times Finishing in the ON position 2 Press valet switch 2 times holding in on
12. e equipment and the original vehicle in which it was installed by an authorized installer under the following conditions If the product proves defective according to Auto Page s testing within the first year the defective unit may be exchanged or repaired free of charge Proof of Purchase dated sales receipt must accompany all warranty returns otherwise your return will be rejected and sent back After one 1 year the purchaser should ship the unit prepaid to Auto Page with a money order in the amount of 30 00 to cover shipping and handling charges Note The enclosed Warranty Card may be required to receive warranty services 2 This WARRANTY will be considered void if the equipment has been misused neglected improperly serviced or installed altered dropped or damaged by water contrary to the Auto Page OPERATIONS MANUAL Or if used with accessories not approved by Auto Page which may have contributed to the defect See note below regarding product installation 3 The purchaser s remedies under this WARRANTY shall be limited to the repair or replacement of electronic components only THE FOLLOWING IS NOT COVERED Damages or deterioration to cases batteries covers and cabinets the cost of repairs replacement and labor of which shall be borne by the purchaser even if occurring during the WARRANTY period 4 Any equipment or parts which are claimed to be defective under this WARRANTY must be sent to the Auto Page Service cent
13. e vehicle running Exit the timer start Timer start can be exited manually as follows Make sure the remote start system is not operating the engine 2 Turn the ignition on The LED and parking light will flash 4 times The horn chirps 4 times Or Press the button twice to remote start the vehicle As soon as the vehicle is running and the parking light have turned on or flashing Immediately depress the button then press and hold the button for 2 seconds or depresses buttons if you programa buttons Start Stop button The parking light will flash 4 times The siren or horn chirps 4 times The vehicle is no longer programmed to start automatically F TEMPERATURE CHECK OPTIONAL If you installed the optional temperature sensor you can monitor through the LCD screen the present indoor temperature of the passenger compartment before cooling or heating your vehicle Press the transmitter SET buttons first within 3 seconds press the button the in door temperature will be shown on the LCD screen This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature G TO TURN OFF THE REMOTE START When the engine is running by remote start if you want to stop it ii 1 Press button once on the remote transmitter under remote start mode Lg 2 Move the optional remote start enable to
14. ed The vehicle door will lock upon arming when interfaced with the security system 13 System Arm Door Ajar AM Trunk Hood Ajar Clear The Flash Icon Press the SET button 3 times within 3 seconds will clear the flash icon on the LCD screen E transmitter D J DEFECTIVE SENSOR REMINDER If the siren sounds 3 chirps then you have left a door trunk or hoodlid ajar SILENT ARMING DISARMING Press the transmitter E and T button at the same time will arm or disarm your security system No chirp sound will be heard arm disarm confirmation will be through the vehicles parking lights only SHOCK SENSOR BY PASS Press the e button on the transmitter two times within 3 seconds will arm the security system and by pass the shock sensor The system will chirp one additional time to confirm the sensor bypass mode was activated The sensor bypass feature is programmed to activate for one arming cycle only The security system will return to normal operation during the next arming cycle H PASSIVE ARMING Active arming disarming is controlling your security system via the remote transmitter This security system is equipped with an optional Passive Arming feature which allows the security system to arm 30 seconds after the last door is closed Operation is as follows 1 Turn the ignition to the OFF position and exit the vehicle 2 After all entrances are closed the security sy
15. eed to use it to completely disarm the system 18 P SYSTEM S TRIGGER CHECK Press the transmitter SET first within 3 seconds press A C button It responds with one melody sound and all trigger s records will immediately displayed on the LCD screen Q SYSTEM S STATUS CHECK When you want to check the system s present status through the LCD screen Press the transmitter SET button twice within 3 seconds press baal C button It responds with one melody sound R DRIVER PAGING It is useful the event that someone wants to page the driver of the parked vehicle In Car Driver Paging Under the ignition switch off condition press and hold the valet switch for 2 seconds to page the driver one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and indication flashes the LCD screen Out of Car Driver Paging If someone tries to page you by tapping the paging knock sensor optional which is usually mounted on the bottom part of front window the paging melody sound continues sounding from you Remote LCD Transmitter and Se indication flashes on the LCD screen 1 Press the transmitter SET button first within 3 seconds press button to activate outdoor driver paging function It responds with chirps of the vehicle a melody sound and Sg indication flashes on the LCD screen to confirm the function is on 2 Wh
16. en tapping the paging knock sensor one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and Sg indication flashes on the LCD screen 3 Turn on the ignition switch OR press the ig button to arm the system OR press the 88 button to disarm the system this outdoor driver paging function will exit 19 S DOME LIGHT CONVENIENCE DELAY amp SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following 1 Upon disarming the interior light will remain on for 30 seconds 2 lf the vehicle is intruded the interior light will flash for the same duration as the siren Note Turn on the ignition switch or arm the alarm will turn off the dome light T IGNITION CONTROL DOOR LOCK UNLOCK If the vehicles door locks have been interfaced to the security system the system will automatically lock the vehicle s doors when the ignition is turned ON and or unlock the vehicle s doors when the ignition is turned OFF U TRUNK RELEASE CHANNEL 3 OUTPUT Press and hold a button on the transmitter for two seconds to remote control the trunk release or other electric devices V CHANNEL 4 TIMER CONTROL OUTPUT Press the transmitter a 4 and 4 button at the same time to active Channel 4 function Channel 4 1 user programmable timer output You may program the built in timer to send a ground signal for any tim
17. er with proof of purchase at the purchaser s expense prior to such return a Return Authorization Number should be obtained Auto Page will return the equipment charges prepaid Warranty Service can be provided through the dealer where the equipment is originally purchased 5 Any unexpired WARRANTY shall be applicable to equipment and parts in the possession of the original purchaser only 6 THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE 7 Auto Page shall not be liable under the foregoing WARRANTIES or otherwise for Any personal injury of any kind to the purchaser its employees or agents or anyone else whomsoever resulting directly or indirectly from the use or presence of the equipment or parts Consequential damages of any kind any inability of the purchaser to use the equipment The attached WARRANTY CARD is for your record However Auto Page reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service Please keep this card in a secured place IMPORTANT NOTE damages to the alarm system resulting from an installation performed by anyone other than a professional installation technician authorized by a dealer of Auto Page will void the product s limited lifetime warranty 26 This WARRANTY CARD is for your record However
18. et mode The valet switch allows you to temporarily bypass all alarm function eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions and remote start functions are bypassed however the remote panic feature and remote door locks will remain operational To use the valet mode the system must first be disarmed either by using your remote transmitter or by operating the Manual override sequence Enter Valet Mode 1 From the disarmed condition turn the ignition to ON position 2 Push and hold valet switch for 2 seconds until the LED turns on The LED wills remain on as long as the system is in valet mode Exit Valet Mode 1 Return to normal operation turn ignition on 2 Push and hold valet switch for 2 seconds The LED will turn off indicating the system is exiting the valet mode L CAR LOCATOR M w 2 00 Under armed mode press the button to active C ARMED car locator function The siren will chirp 6 times The parking light will flash 12 times for you to easily locate your car M PANIC FUNCTION The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency 16 1 Press and hold the button for second The alarm will immediately sound 2 During panic mode the normal function of this transmitter button will be disabled The transmitter a and b
19. ggle switch to OFF position If installed 3 Press the brake pedal The vehicle will shut down and turn off f the parking light to indicate engine stopped SHUT DOWN INPUT FOR REMOTE STARTER If any of the following conditions exist while the system is operating the engine will not start or will shut down immediately 1 The hood is opened 2 The brake pedal is pressed 3 Engine is over revved Tachometer checking type only 24 4 The pre programmed run time 5 10 20 30 minutes has elapsed 5 Press button once on the remote transmitter under remote start mode 6 Move the optional remote start enable toggle switch to OFF position If installed 7 The vehicle refused to start running after 3 unsuccessful attempts I DISABLING THE REMOTE START SYSTEM If installed This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the optional remote start enable toggle switch to the OFF position LIMITED LIFETIME WARRANTY PROVISIONS U S Continental U S and Canada Only 23 1 Auto Page Inc WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery Your Auto Page equipment is guaranteed for life to the original purchaser user of th
20. increase the Hour digit until 2 xx 4 Press the SET button once again then the Minutes digit flashes for adjusting 5 Press the or button to decrease or increase the Minute digit until 2 30 6 Press the SET button once again then 9 ON OFF setting 7 Press the ae button to start the count down timer and the ON icon will show on the LCD screen Press the button to stop the count down timer and the OFF icon will show on the LCD screen icon flashes for alert alarm 8 Press the SE button for 2 seconds with one melody sound to confirm exit the timer program mode Note Maximum is 19 hours 10 4 Time Set Up For Daily Timer Start Example to AM 6 30 1 Press amp hold the SET button for 3 seconds with two melody sound and the Hours digit flashes for adjusting 2 Press amp hold the z button for 2 seconds the LCD screen will flash V icon and Hours digit for Hour set up 3 Press the or button to decrease or increase the hour digit until AM 6 00 4 Press the SET button once again then the minute digit flashes 5 Press the x or ae button to decrease or increase the minutes digit until AM 6 30 6 Press the SE button for 2 seconds with one melody sound to confirm exit the timer program mode OPERATION A REMOTE TRANSMITTER OPERATION Transmiter System Function Remark Button Press and Hold for 3 seconds Arm and Delete The 2 Stage Press twice within
21. osition Alarm will sound 2 Within 5 seconds enter your chosen the first digit code by pressing and releasing the Valet Switch When finished above procedures system s siren stop alarming lights stop flashing but the vehicle can t be started 3 Within 15 seconds of the last digit code enter the 1st code turn the Ignition Switch OFF and then ON 15 4 Within 15 seconds enter your chosen of the second digit code by pressing and releasing the Valet Switch 5 Turn the ignition switch OFF position 4 Chirps form siren horn 3 flash from parking light to indicate the system was disarmed Note 1 You must override the alarm within 60 seconds If not the system will automatically re arm EXAMPLE To Override The System With The Password Code 83 1 Enter the vehicle and turn the ignition switch to ON position Alarm will sound 2 Within 5 seconds Press and Release the Valet Switch 8 times When finished above procedures system s siren stops alarming lights stop flashing and sensor stops trigger but the vehicle can not be started or driven away 3 Within 15 seconds of the last digit code enter the 1 code turn the Ignition Switch Off and then ON 4 Within 15 seconds Press and Release the Valet Switch 3 times 5 Turn the Ignition Switch to Off position 4 form siren horn 3 flash from parking light to indicate the system was disarmed K VALET MODE System in Disarm or Val
22. others 1 The XT 85s Standard transmitter Press the button first within 3 seconds press and hold the E button for 2 seconds to activate or cancel the button lock function The Red LED will pause flash for few seconds to indicate the remote control transmitter is on Button Lock mode when pressing the transmitter button 2 The 2 way LCD transmitter Press the SE button first within 3 seconds press E and hold the E button for 2 seconds to activate or cancel the button lock function The icon will be displayed on the LCD screen to confirm that the LCD remote transmitter is in the Button Lock mode 12 C LED display LED Off Slow Flash Armed Zone 1 Warn Away Trigger 2 flashes Zone 2 Trigger on Trunk Hood pause Flash Passive Starter Disable On Solid Valet Mode pause pause Sensor Zone 5 Trigger on Ignition pause Switch D CHIRP INDICATORS E PARKING LIGHT Chirp 1 chirp 2 chirps Constant On Under Remote Start F ALARM OPERATING CONDITION EN TO a one i 20r3 Turns for 30 4 Passive Starter Fast Disable Flash Disable 5 Panc Naming ass 6 Car Jacking Alarming Flashes Disable Flashes pem puel _ G ACTIVE ARMING LOCK amp ARM 1 Press bas button on the transmitter 2 The siren will chirp once and parking light will flash once indicating that the system is now arm
23. r button until hour flashes Flash digit for adjusting Press the 9E button Time setting Minute for and for once Flash digit for adjusting Alert Alarm Time Setting 2 Press the SET button Hour for m for once Flash digit for adjusting Alert Alarm Time Setting Press the SET button Minute for and for once Flash digit for adjusting ae Press the SET button Alert Alarm Setting ON OFF for ON Count Down Timer Setting Press the SE button Hour for and for once Flash digit for adjusting Max 19 hours 59 minutes Count down Timer Setting Press the SET button Minute for and for once Flash digit for adjusting Press the SET button Count down Timer Setting tor OFF and once ON OFF for ON Daily Timer Start Timer Press amp hold the Setting Flash S for and 3 for button for 2 seconds icon and Hours for adjusting EXIT Press and hold the SET button for 2 seconds or leave it for 10seconds the system will exit the programming mode 1 Clock Setting Example to AM10 30 1 Press amp hold the SE button for 3 seconds with two melody sound and the Hours digit flashes for adjusting 2 Press the or button to decrease or increase the Hour digit until AM10 xx 3 Press the SE button once again then the Minute digit flashes for adjusting 4 Press the or button to decrease or inc
24. rease the Minutes digit until AM 10 30 5 Press the SE button for 2 seconds with one melody sound to confirm exit the timer program mode 2 Alert Alarm Timer Setting Example to PM 6 30 1 Press amp hold the SE button for 3 seconds with two melody sound and the Hours digit flashes for adjusting 2 Press the SET button twice the LCD screen will shows 4 icon and Hours digit is flashing for adjustment 3 Press the or button to decrease or increase the Hour digit until PM 6 xx 4 Press the SE button once again then the Minutes digit flashes for adjusting 5 Press the or em button to decrease or increase the Minutes digit until PM 6 30 A 6 Press the SET button once again then icon flashes for alert alarm ON OFF setting 7 Press the button to start the Alert Alarm Timer and the ON icon will show on the LCD screen Press the button to stop the Alert Alarm Timer and the OFF icon will show on the LCD screen 8 Press SE button for 2 seconds with one melody sound to confirm exit the timer program mode 3 Count Down Timer Setting Example Set count down timer at 2 30 1 Press amp hold the SET button for 3 seconds with two melody sound and the Hours digit flashes for adjusting 22 2 Press the SE button 5 times the LCD screen will shows 9 icon and Hours digit is flashes for adjusting 3 Press the or button to decrease or
25. rogrammed temperature level The system will monitor the air temperature every 3 hour and will only start the engine during extreme cold temperatures There are three temperature levels to choose from Daily Timer Start The feature is very useful for the driver who wants to run the vehicle punctually at the same time next morning Before set up of the Daily Timer Start you should set you time for engine start see Timer Setting Timer set up for Daily Timer Start page 16 ENTER 1 Press the button once to remote start the vehicle As soon as the vehicle is running and the parking light have turned on or flashing 2 Immediately depress the button once within 2 seconds 3 a 3 Hours Timer Start Rapidly depresses the button or depresses E buttons if you programa buttons Start Stop button The parking 23 light will flash 3 times The siren or horn chirps 3 times The vehicle is now programmed to start every 3 hours 3 b Daily Timer Start Depress the transmitter SET button first within 3 seconds press button The parking light will flash 6 times The siren chirps 6 times The vehicle is now programmed to start at the real time of the next day Your set time for the next CIL UJ g CTA day engine start flashes for approx 3 seconds on the LCD screen After 3 seconds the gt icon stays displayed on the LCD screen 4 Press the brake pedal to stop th
26. smitter TAMPER DISARMING If alarm is triggered upon disarm the systems siren will chirp 4 times and parking light flash 3 times PATHWAY ILLUMINATION This feature turns the parking light ON for seconds upon a unlock signal and for 10 seconds upon the lock signal TWO STEPS DOOR UNLOCK This feature will independently unlock the driver s door only when disarming the security system Pushing the amp button a second time within 3 seconds will unlock the other doors AUTOMATIC RE ARM If this feature is selected the security system will automatically re arm itself in 60 seconds after disarming with remote transmitter Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed J DISARMING WITHOUT A TRANSMITTER OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE Factory Default Setting The Override function may be used if the remote transmitter is lost or inoperative 1 Enter the vehicle and turn the ignition switch to ON position 2 Alarm will sound 3 Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode You can now start and operate the vehicle normally OVERRIDE THE ALARM WITH PASSWORD PIN CODE Unlike valet switch easily found and defeated this security system allows the consumer to program a password pin code Offering a higher level of security 1 Enter the vehicle and turn the ignition switch to ON p
27. stem LED will flash fast for 30 seconds If you reopen any door hood trunk the security system LED will stop flashing lt will begin flashing again once all vehicle entrances are closed 3 After 30 second timer has elapsed the security system will automatically ARM The siren will chirp 1 time and the parking lights will flash 1 time PASSIVE ARMING WITH PASSIVE DOOR LOCKING The vehicle doors will automatically lock after passive arming cycle has been completed PASSIVE ARMING BY PASS While the system is disarmed Press the buttons twice the system will respond with 1 chiro and LED will turn ON The security system will remain in this temporary state for as long as you wish To exit passive by pass press the transmitter g button and the system will return to normal status ACTIVE DISARMING UNLOCK amp DISARM 1 Press g button on the transmitter 2 The siren will chirp twice and parking light flash twice to indicating that the security system is now disarmed The vehicle s door will unlock and dome light turns on for 30 seconds upon disarming when interfaced with the security system 14 System Disarm Doors Trigger Trunk HoodTrgr Warn away Trigger Gg m DLL e Shock SensorTrgr Clear The Flash Icon Press the SET button 3 times within 3 seconds will clear the flash icon on the LCD screen tran
28. ter you have left the vehicle To activate 1 While the engine is running pull up the hand brake and place the transmission gear in the park position 2 Before turning off the engine press and release buttons at the same time The LED will flash indicating the remote start has entered the turbo charge mode 3 Take the Ignition Key from the key cylinder Engine keeps running 4 Exit and secure the vehicle Engine continues running until the pre programmed time elapsed NOTE This feature only applies to vehicles with Turbo Engines E TIMER TEMPERATURE START This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next morning the engine will run for the programmed running time and then shut down IMPORTANT Timer Start should be used only in open areas never start and run the vehicle in on enclosed space such as a garage or carport 3 hours timer start with Temperature control OFF This feature is design for an extreme cold climate usage The system will auto start the vehicle every 3 hours to prevent engine freezing and hard to start A MAXIMUM OF SIX CYCLES CAN OCCUR 3 hours timer start with Temperature control If you installed the optional Temperature Sensor and programmed the temperature ON to operate The system can be programmed to automatically start the vehicle engine whenever the temperature inside the vehicle reaches or drops below the prep
29. tery power Button Lock Disable the transmission function temporarily Low Battery You have to replace the battery of remote control C PROGRAMMING OF THE LCD REMOTE TRANSMITTER Operation SET LCD screen lamp turns on Press and hold for 1 second 1 second for 1 melody sound to confirm 5 seconds enters Timer Programming Mode Press and hold for 3 SET 3 seconds 9 9 seconds 2 melody sounds to confirm enter SET Power Save Mode Press and hold for 5 5 seconds seconds 1 melody sound to confirm enters Clear the Flash Icon and Press within seconds Screen Transmitter Press within 3 seconds 0 il Button Lock enable disable OOO 2 second Melody Vibration Press within 3 seconds Mode ge ram Count Down Timer Within 3 seconds press the SET 2 second 2 E as p 10 Minute 20M 30 Y button desired M 1 Hour 1 5H 2 0H 1 Screen Lamp ON Press and hold the SET button one second with one melody sound and the LCD screen lamp will turns on for 5 seconds 2 Power Save Mode While the power save mode the LCD remote transmitter uses O current to save the battery power Entry 1 Press amp hold the SET button for 5 seconds with one melody sound and SAVE icon on the LCD screen to indicate entry the power save mode 2 Under the Active Arming Mode and Disarm mode Turn the ignition switch to on the LCD remote transmitter
30. the gne push you will hear a long siren chirp Release the valet switch 3 Press the shift button of the Car 2 transmitter LCD transmitter must be put in 2 car mode to program for 2 car See next page 4 Press the lock button on the transmitter you will hear 1 siren chirp Turn OFF the ignition switch you will hear 3 long siren chirps to confirm programming and exit transmitter programming For 2 way LCD Display Transmitter 2nd Car Operation 1 Press SET first within 3 seconds press and hold e and al buttons at the same time for 2 seconds Two beeping sound and the nd icon will be displayed on the LCD screen to indicate the second transceiver pin code is programmed 2 While the nd icon is displayed on the LCD screen you can remote control and communicate with a second vehicle security system It has two short bi sounds while pressing the button of the LCD screen transceiver Back to 1st Car Operation 1 Press SET first within 3 seconds press and hold buttons at the same time for 2 seconds One long beeping sound and the m bur timer icon will be displayed on the LCD screen indicating the system is back to the first transceiver pin code 2 While the a EL timer icon is displayed on the LCD screen you can remote control and communicate with the first vehicle security system It has one short bi sound while pressing the button of the LCD screen transceiver Z POWER
31. tter to start the vehicle Programming this feature to eliminate an accidental remote start 1 The user presses the transmitter buttons twice within 3 seconds to start the vehicle or 2 The user presses the transmitter buttons at the same time to start the vehicle B TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START To operate the vehicle while the engine is running on the remote start 1 Insert the ignition key and turn it to ON not the start position 2 Press the brake pedal Note If the brake pedal is pressed before the key is in the ON position the engine will shut down C TEMPORARY STOP FEATURE This feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate control on 1 Before turning off the engine press the button twice on the transmitter and the LED indicator will flash 3 times to confirm enter 2 Turn the ignition key to OFF position The engine will stay running 3 The engine will run until the pre programmed time elapsed or shutdown input is received D TURBO CHARGE MODE 22 Turbo charge mode keeps the engine running after arriving at your destination for a programmable period of 1 or 5 minutes This allows the vehicle s engine time to conveniently cool down the turbo af
32. uttons can be used to lock and unlock the door if the option is installed however once the button is pressed the vehicle s starter disable device where installed will be disengaged allowing the vehicle to start 3 To stop the alarm press and hold the transmitter la or transmitter again for 3 seconds Also if any transmitter button other than a or 8 button is pressed and released the panic mode will be turned off immediately 4 f the button is not pressed the alarm will automatically stop after 30 seconds N TRIGGER THE SYSTEM When armed your vehicle is protected as follows 1 Light impact will trigger the warn away signal 2 Heavy impacts Doors open Hood open Trunk open Turning on the ignition key will trigger the programmed sequence The starter disable relay if installed prevents the vehicle s starter from cranking The siren horn parking lights and dome light will turn on to alerting of an intrusion for 30 seconds Then it will stop and automatic reset and re arm If the one of sensors or detectors still active the alarm system will sound a maximum of 3 times of 30 seconds cycles Door Trigger Trunk Hood Trigger Warn away Trigger Shock Sensor Trigger CLEAR THE FLASH ICON AND MELODY SOUND While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon press the SET button 3 times within 3 seconds will clear the flash icon and stop
33. will automatically entry the Power Save Mode Exit Press any button of the LCD remote transmitter to exit the Power Save Mode 3 Clear the Flash Icon and Melody Sound Press the SET button 3 times within 3 seconds will clear the flash icon and melody sound on the LCD screen transmitter 4 Stop The Trigger Melody Sound While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon press any button on the LCD remote transmitter to stop melody sound only 5 Button Lock It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others Press the SET button first within 3 seconds press and hold the 8 button for 2 seconds to activate or cancel the button lock ux function the icon will displayed on the LCD screen to show the LCD remote transmitter is on Button Lock 6 Vibration Melody Mode It is useful when you are in a noisy place and difficult to hear beep sound from the remote control The remote control in this mode will vibrate when your security system is triggered Press the SET button first within 3 seconds press and hold the bbb vibration or melody the icon will displayed on the LCD screen to show the LCD remote transmitter is on vibration mode BOO 4 button for 2 seconds to select the mode of 7
34. xpose batteries Remove v old batteries and replace with pU 1 um F L rd e i Mur 2 CR2025 lithium 3 volt batteries CRAS 4 VOLT i B THE REMOTE LCD ICONS WITH FUNCTION IGN Door Lock Your vehicle doors are locked Armed Mode Your vehicle is in armed mode Remote Transmission You are transmitting the signal to control unit Door Open Warning Doors are illegally opened Zone 3 Shock Sensor Trigger Trigger on Shock Sensor Zone 4 Engine Starting Your vehicle engine starting by remote control Timer Control Start Start the Engine automatically at the P T FE same time next day or every 3 hour Time Monitor 9 770 C SAS Count Down Timer Reminder when time is up for parking Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle Door Unlock Your vehicle doors are unlocked and the system is Disarmed Valet Mode All the function shall be temporarily on hold In Range Indicator Your are within the remote control range Trunk Hood Trigger Trunk or Hood is illegally opened Zone 2 Warn Away trigger Trigger on Shock Sensor Zone 1 Engine Running Your vehicle s engine is running Temperature Monitor Indoor temperature of your vehicle Alert Alarm You have set morning call alarm Power Save Mode Save the bat
Download Pdf Manuals
Related Search