Audiovox VM9114 Installation Manual
Contents
1. Ignition Switch ACC To BATTERY Need Help For technical assistance call the Jensen customer support line at 1 800 323 4815 Ground be qf FUSE 15A BATTERY YELLOW BATT BLACK GND Harness Cord BLUE ANT CONT BLUE WHITE BROWN WHITE w PARKING BRAKE Auto antenna control connect to antenna control lead amp power supply of antenna External power amplifier control Mute leave open if not connected 7 se a SS lt a External Power Amplifier CHEE am f Antenna Jack amplifier WHITE BLACK GREY FRONT L Soe FRONT L r FRONT L GREY BLACK PURPLE GREEN BLACK FRONTR P JFRONT R REAR R REAR R REAR L REAR L2. the opening or cause it to bend or bow b Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully insert ed into the dashboard opening bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard c Install support strap to make the unit more stable Ey Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve CAUTION Be careful not to damage the car wiring DASHBOARD Wiring WARNING Only connect the unit to a 12 volt power supply with proper grounding Complete wiring as illustrated in the wiring diagram on page 4 Once the wiring is complete reconnect the bat tery negative terminal If there is no ACC available connect the ACC lead to the power supply with a switch NOTE When replacing a fuse be sure to use correct type and amperage to avoid damaging the radio The VM9114 uses one 15 amp fuse located in the black filter box in line with the main wire harness Final Installation After completing the wiring connections turn the unit on to confirm operation ignition switch must be on If unit does not operate recheck all wiring until problem is corrected Once proper operation is achieved turn off the ignition switch and proceed with final mounting of the chassis 1 Connect wiring adapter to existing wiring harness 2 Connect antenn
3. Installation Guide 160 Watts What s in the Box VM9114 Head Unit Cosmetic Trim Ring Single DIN Sleeve 3 5mm to 3 5mm Media Adaptor Cable Wiring Harness Owners Manual Parking Brake Sensor Extension Wire Installation Guide Mounting Hardware Tools and Supplies You will need these tools and supplies to install your VM9114 e Torx type flat head and Philips screwdrivers e Wire cutters and strippers e Tools to remove existing radio Screwdriver socket wrench set or other tools e Electrical tape e Crimping tool e Volt meter test light e Crimp connections e 18 gauge wire for power connections e 16 18 gauge speaker wire WARNING Never install this unit where operation and viewing could interfere with safe driving conditions Disconnecting the Battery To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to in stallation NOTE If the VM9114 is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution during installation to avoid causing a short circuit Pre installation 1 Remove the four screws that attach the mounting sleeve to the radio and remove the sleeve 2 Install the mounting sleeve a Install mounting sleeve into the dashboard or optional adapter Do not force the sleeve into
4. a lead a Carefully slide the radio into the mounting sleeve making sure it is right side up and secure with the original 4 screws 4 Attach one end of the perforated support strap supplied to the screw stud which is screwed into the threaded insert on the back of the unit using the hex nut provided Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided Bend the strap to position it as CAUTION The rear of the radio must be MRAN supported with the strap to prevent dam age to the dashboard from the weight of the radio or improper operation due to vibration 5 Replace any items you removed from the dashboard ISO DIN Installation al Remove mounting sleeve brackets NOTE For proper operation of the CD DVD player the chassis must be mounted within 20 of horizontal Make sure the unit Remove trim ring is mounted within this limitation Mount factory brackets on new radio using existing screws from old radio Slide radio chassis into dash opening and secure Re install dash panel Wiring Diagram IMPORTANT Incorrect wiring connections can damage the unit Follow the wiring instructions carefully or have the installation handled by an experienced technician REAR R REAR L ry gt S
Download Pdf Manuals
Related Search