Audiovox PRO-900 User's Manual
Contents
1. Model PRO 900 VT TA Owner s Manual SQ ZS 3 Channel Remote Car Starter FEATURES 1 Three Button Programmable RF Transmitters 1 5 Button Programmable Transceiver Three Channel Transceiver capable of accepting 4 transmitters Keyless Entry Outputs and On Board Start Relay On Board Accessory Relay On Board Ignition 1 Relay On Board Ignition 2 Relay Ignition 2 Relay Selectable On or Off During Cranking On Board Parking Light Relay Ignition 3 Shock By Pass GM VAT Output relay required Tach Signal Learning Circuit Two and Two Safety Shutdown Circuits Alarm By Pass Output Accessory Outputs Pulse Before amp After Start During Crank amp After Shut Down Selectable Steady or Flashing Parking Lights for Run Indication Selectable 5 10 15 20 Minute Run Time Selectable 1 Sec 3 5 Sec or 1 Sec Dbl 1 Sec Door Lock Output Pulse 128 6846 1 of 4 KEYLESS ENTRY 1 The Lock button on the transmitter is used to lock the vehicle s doors the Unlock button is used to unlock the vehicle s doors To lock or unlock the doors simply press and release the desired function button one time As a keyless entry unit for your convenience the parking lights will flash once when the doors are locked and twice when the door are unlocked REMOTE CAR FINDER The Lock or Unlock buttons are also used to access the car finder mode This feature is pa2. e control switch allows you to temporarily disable the remote starting function of the system and moving this switch to the Off position is recommended whenever the vehicle is being serviced When the system is disabled the remote door locks and optional accessories will remain operational FUNCTION SETTING CHART To be completed by installer Run Time 5 Min O 10 Min O 15 Min O 20 Min O Door Lock Timer 1 Sec 1 Sec O 3 50 1 Sec Dbl 1 Sec O Lights Pulse O Steady O Option Button Programmed To Control For Customer Service a Visit Our Website At www audiovox com A Product Information Photos FAQ s Owner s Manuals 2003 Audiovox Electronics Corp 150 Marcus Blvd Hauppauge NY 11788 128 6846 128 6846 4 of 4
3. it is within range of the vehicle will lock the vehicle doors and report back that the command was acted upon by breifly turning on the Lock LED and beeping once This lock LED will flash 1 time every 10 seconds until the Unlock command is issued Press and hold for lock button for three seconds causes the unit to go into the car finder mode See car finder reference shown earlier in this manual Unlocking Press and release the Unlock Icon Button on the transmitter and the unit providing it is within range of the vehicle will unlock the vehicle doors and report back that the command was acted upon by breifly turning on the Unlock LED and beeping twice This unlock LED will flash 1 time every 10 seconds until the lock command is issued Press and hold for unlock button for three seconds causes the unit to go into the car finder mode See car finder reference shown earlier in this manual Starting The Vehicle Press and release two times in succession the Key Icon Button on the transmitter and the unit providing it is within range of the vehicle will Start the vehicle and report back that the command was acted upon by flashing 5 times the Key LED and playing the start melody Operating the lock button or unlock button while the unit is under the control of the remote start will cause the lock or unlock LED to light breifly the transmitter will chirp once for lock or twice for unlock and along with that the Key LED will turn on for 4 seconds indica
4. rticularly useful in a crowded parking lot where finding your car may be difficult To access the car finder mode while within range of your car simply press and hold either the lock or unlock button of your transmitter for three seconds The parking lights will begin to flash making your vehicle more visible The lights will stop auto matically after 30 seconds If you wish to turn off the car finder mode prior to the expiration of the 30 second timer press and release either the lock or unlock button of your transmitter one time REMOTE STARTING THE VEHICLE The system will not start the vehicle if any one of the following situations exists The vehicle s hood lid is opened The gear shift selector is not in Park The brake pedal is depressed The safety control switch is in the Off position 1 To start the vehicle press and release the Key Option button two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 20 minute run cycle As a visual indication the parking lights will flash or remain on depending on the setting by your installation center When you arrive at the vehicle turn the ignition key to the ON position not the spring loaded start position then step on the brake pedal to disengage the remote starter The vehicle will continue to run but now on it s own power NOTE The engine will stop running before the pre programmed run cycle has expired if you perform any one of the follo
5. ting the vehicle is still running under command of the remote start unit 128 6846 3 of 4 The Option Button Press nd release the OPT Button on the transmitter and the unit providing it is within range of the device it is controling will operate the device This option button can be programmed into a number of Audiovox accessories If the accessory is a second two way Audiovox Remote Start Unit perhaps installed in a second vehicle then the vehicle will act upon the command but only the prime transmitter for that vehicle will indicate the command was acted upon Toggling Between Vibrate Chirp or Both Chirp amp Vibrate The two way transmitter offers the option of having Beep Tones Vibration or Both Beep Tones amp Vibration associated with the function responses of the transmitter To toggle between these modes press simultaneously the F function button and the Unlock Icon Button The transmitter will beep beep amp vibrate or vibrate only toggeling on the specific preference Check Vehicle Status Press the lock key option buttons simultaneously for 1 second The vehicle s alarm will display the systems current status breifly by flashing the LED associated with the state the vehicle was left in This feature is useful if you do not want to wait the 10 seconds for a LED to display the status or if you just want to check the status without operating the Lock or Unlock buttons SAFETY CONTROL SWITCH The red handl
6. wing functions Press and release button 2 on the keychain transmitter two times within 2 seconds Depress the brake pedal fral Open the vehicle s hood Move the safety control switch to the Off position Your unit is also packaged with a two way confirming transmitter shown Right which has Icon LED s to indicate the function and status of your vehicle The top LED indicates a Transmit whenever a transmitter button is operated this LED will turn on Green b Out of range when after pressing a transmitter button if the unit does not receive the command this LED will turn on Red and the transmitter will beep twice indicating the command was not received or acted upon by the unit in the vehicle c Low Battery if when pressing any transmitter button this LED illuminates Red 128 6846 20f 4 The Lock LED Indicates When the lock button on the transmitter is pressed and the command is received and acted upon by the unit in the vehicle this LED will light Red and the transmitter will beep once then will continue flash once every 10 seconds so you at a glance can determine the status of your vehicle or determine the state it was last left in The Unlock LED Indicates When the unlock button on the transmitter is pressed and the command is received and acted upon by the unit in the vehicle this LED will light Red and the transmitter will beep twice then will continue flash once every 10 seconds so
7. you at a glance can determine the status of your vehicle or determine the state it was last left in The Key LED Indicates When the key transmitter button is operated two times in succession and the start command is received and acted upon by the unit in the vehicle this LED will light Red and the transmitter will play the remote start melody indicating that the vehicle is running and will continue to run for the preset period as determined at time of installation If you wish to prematurely shut down the remote start while the vehicle is still running simply press the key transmitter button two times in succession The vehicle will turn off and the Not Key LED will turn on breifly oF The Not Key LED Indicates Whenever the remote start turns off either by intentional activation on the part of the operator or by timing out after the preset run timer this Not Key LED will light Red breifly and the transmitter will play the shut down melody NOTE If the vehicle is under the control of the Remote Start and the vehicle is running when either Lock or Unlock button is pressed the Lock or Unlock LED and the Start LED will turn on momentarily Two Way Transmitter Operation The two way transmitter shown earlier in this manual operates similar to any transmitter with the exception that it will also indicate that the vehicle acted upon the command issued Locking Press and release the Lock Icon Button on the transmitter and the unit providing
Download Pdf Manuals
Related Search