Audiovox PRO 2000S User's Manual
Contents
1. Model PRO 2000S SGAE Owner s Manual SN S 3 Button Remote Security System with Keyless Entry IMPORTANT In order to pose the highest possible level of security to your vehicle this system is equipped with selectable manual override circuitry It is possible that you will need to manually override your security system if the transmitter becomes lost or inoperative due to battery failure Reading the sections on MANUALLY OVERRIDING YOUR SYSTEM is necessary to fully understand the procedure required to enable your vehicle in such situa tions In addition the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected Valet Switch manual override is pre selected from the factory however the system can be configured for Custom Code operation Confirm the override mode selected on the last page of this manual and familiarize yourself with the selection on it s operation FEATURES 2 Three Button Programmable RF Transmitters capable of accepting 4 transmitters Four Channel Receiver Selectable Manual Override Mode Remote Panic in all modes Protected Valet User Programmable Manual Override Code 7 Function LED Arm Disarm Zone 1 Zone 2 Zone 3 Valet Arming Intrusion Alert with Memory Audible Arm Disarm Defective Zone Tamper Confirmation Instant Siren Activation True Last Door Armin2. and release the valet pushbutton switch The alarm system will stop sounding You can now start and operate the vehicle normally Typically this override mode is used only if the transmitter has become inoperative If this is the case you may want to enter the valet mode until a operating or replacement transmitter is available PROGRAMMING THE CUSTOM CODE MANUAL OVERRIDE Unlike override switches easily found and defeated this security system allows the consumer to program a personal override code offering a higher level of security To take advantage of this option programmable feature 9 must be selected for the Custom Code Option Consult your installation center for pro gramming details The system comes from the factory with a pre programmed override code of 11 To change this default override code do the following Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position Within 10 seconds press and release the valet override switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time Within 10 seconds begin to enter your chosen 10ths digit by pressing and releasing the pushbutton switch from 1 up to 9 times Within 10 seconds of the last entered 10ths digit turn the ignition switch off then on Within 10 seconds begin to enter your chosen units digit
3. are O Remote Electric Trunk Release O Remote Car Starter O Remote Window Closure O Remote Garage Door Interface NOTE In addition there may be a second optional feature connected to your system that when the same transmitter button is pressed and released 2 times within 3 seconds double pressed the second optional feature will activate This output is typically used for a remote start option and will likely prevent inadvertent activation of the remote start device if young children are playing with the hand held transmitter If your vehicle is not equipped with an electronic trunk release switch or other option listed this feature may have been connected to another accessory Please ask your dealer for further information ADDITIONAL REMOTE FUNCTION CHANNEL 4 Controlled By O Option Button O Both Lock amp Unlock Button O Both Option amp Lock Button or O Both Option and Unlock Button This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this chan nel are O Remote Car Starter O Remote Window Closure O Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above PRO 2000S SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING PASSIVE ARMING SLOW FLASHING ARMED OFF DISARMED ON SOLID VALE
4. by pressing and releasing the pushbutton switch from 1 up to 9 times Finish by turning the ignition switch to the off position If the new code was accepted the unit will report back the newly entered code by flashing the LED first indicating the 10ths digit pause and then the units digit The unit will report the new code three times with a one second pause between each code then the system will begin arming If the LED flash pattern reports the previously stored code the new code was not entered correctly Please repeat steps 1 through 7 above considering the following NOTE Acceptable digits 10ths or units are 1 through 9 The unit will not recog nize a 0 Zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code Custom Code Programming Example To Change the code from the factory pre assigned code of 11 to 52 you would do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position Within 10 seconds press and release the valet override switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time Within 10 seconds
5. vehicle and turn the ignition switch to the on position Note The siren will sound 2 Within 5 seconds press and release the pushbutton switch 1 time 3 Within 5 seconds turn the ignition switch off then on 4 Within 5 seconds press and release the pushbutton switch 1 time 5 Turn the ignition switch off then on and start the vehicle Note If you have changed the programmed override code then substitute your new code tenths for step 2 above and units for step 5 above ELIMINATING THE NORMAL ARM DISARM CHIRPS As explained earlier in the manual you can eliminate the chirps selectively any time you arm or disarm the system simply by holding the ARM DISARM button for two seconds If you find the normal arming and disarming chirps annoying they can be turned off permanently eliminating the need to hold the ARM DISARM button for two seconds To do this 1 Turn the ignition key on then off 2 Within 10 seconds press and release push button switch three times 3 If the chirps were on before you started then you will hear 2 chirps indicating they have been turned off If the chirps were off before you started then you will hear one chirp indicating they have been turned on NOTE Whenever the chirps are by passed the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate Since these are important warnings to you that something has happened they cannot be eliminat
6. T MODE 3 FLASH PAUSE INTRUSION ZONE 3 2 FLASH PAUSE INTRUSION ZONE 2 1 FLASH PAUSE INTRUSION ZONE 1 SIREN AND OR HORN CHIRP INDICATORS 1 CHIRP ARM 2 CHIRPS DISARM 3 CHIRPS ARM DOOR OPENED 4CHIRPS DISARM INTRUSION These chirps are optional and can be de activated PARKING LAMP INDICATORS 1 FLASH ARM 2 FLASHES DISARM 3 FLASHES DISARM INTRUSION Your System Has These Features Activated O Auto Lock with ignition key O Auto Unlock with ignition key O Interior Illumination during disarm O Passive Arming O No Lock in passive mode O Hardwire doors hood and trunk O Custom Code Override O Valet Switch Override O Acces Guard A NN For Customer Service Visit Our Website At www audiovox com Product Information Photos FAQ s Owner s Manuals 2001 Audiovox Electronics Corp Hauppauge NY 11788 128 6104
7. begin to press and release the push button switch to set the tenths digit As per the example press and release 5 times to set the tenths digit to 5 Within 10 seconds of the last press of the push button turn the igntion switch off then on Within 10 seconds begin to press and release the push button switch to set the units digit As per the example press and release 2 times to set the units digit to 2 Turn the ignition switch to the off position Immediately observe the LED flash pattern You will note the LED flashing five times pause and then flash two times pause This pattern will be repeated three times indicating the new code 52 has been accepted and stored in memory NOTE If after step 7 the LED flashes a code other than what was just entered this indicates that the code has not been changed You will have to repeat steps 1 through 7 above being certain to note the following Acceptable digits 10ths or units are 1 through 9 The unit will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed and the default override code of 11 is in the system s memory 1 Enter the
8. d If the thief should choose to ignore the siren the vehicle can not be started O OPTIONAL Any strong impact to the vehicle s glass will cause the alarm to trigger for the full 30 second alarm cycle DISARMING THE SYSTEM 1 As you approach the vehicle press and release the Unlock button on the keychain transmitter M Red dash mounted LED turns off If passive arming was selected during the installation then the LED will start flashing rapidly indicating that the system is re arming automati cally Open any door to suspend the automatic arming M Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered M Siren sounds two chirps If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered If the siren did not sound when disarming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual M Doors Unlock Using the optional Access Guard feature the alarm can be wired to unlock only the drivers door during this step To unlock all the doors press and release the Unlock button of the transmiter a second time within 3 seconds Power Doo
9. ed REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations To use remote panic 1 Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds The alarm will immediately sound 2 To stop the alarm press and hold the Lock or Unlcok button on the transmitter again for 3 seconds If the button is not pressed the alarm will automatically stop after 30 seconds Also if any transmitter button other than the Lock or Unlock button is pressed and released the Panic mode will be turned off immediately The normal function of this transmitter button will be suspended during the Panic sounding period NOTE While in the Panic mode pressing and releasing the Lock or the Unlock buttons will if the option is installed lock and unlock the doors respec tively While in the panic mode anytime the unlock button is pressed the the panic feature will continue for the alloted 30 seconds however the security system will be disarmed allowing the vehicle to start OPTIONAL DEVICE OUTPUT CHANNEL 3 Controlled By O Option Button O Both Lock amp Unlock Button O Both Option amp Lock Button or O Both Option and Unlock Button This security system is equipped with an output which will activate when the appropriate transmitter button is depressed for 4 seconds Optional devices that may be connected to this channel
10. ed dash mounted LED begins to flash slowly M Parking Lights flash one time M Siren sounds one chirp If the siren sounds 3 chirps then you have left a door trunk or hood lid ajar Simply close the opened entry point to provide full protection If the siren did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual M Doors Lock SILENT ARMING ACTIVE 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press and hold the Lock button on the keychain transmitter for 2 seconds M Red dash mounted LED begins to flash slowly M Parking Lights flash one time M Siren will not sound If the siren sounds 3 chirps then you have left a door trunk or hood lid ajar Simply close the opened entry point to provide full protection M Doors Lock ARMING THE SYSTEM PASSIVE AUTOMATIC 1 Turn off the engine exit the vehicle and close and lock all doors hood lid and trunk lid M Red dash mounted LED begins to flash rapidly indicating 30 second passive arming has begun 2 Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arming cycle will re start when all doors are closed At the end of the passive arming cycle M Red dash mounted LED begins to flash slowly M Parking Lights flash one time M Sire
11. g hardwire only Defective Zone By Pass Hardwire or Voltage Sense Selectable Active or Passive Arming Selectable Programmable Auto Lock On Off Programmable Auto Unlock On Off Programmable Door Lock Pulse Duration Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter Or Selectable Through Software Additional Negative Trigger Input 6 Tone Multi Tone Siren And or Car Horn Activation for additional alarm response RF Inhibit with ignition on Parking Light Flasher Remote Trunk Release Option and must have electronic trunk release Remote Keyless Entry With Optional Access Guard must have power door locks OPTIONS Illuminated Entry Starter Disable Multiple Vehicle Capable Remote Starter Remote Power Window Roll Up Remote Garage Door Interface Plug In Electronic Shock Sensor THIS PAGE INTENTIONALLY LEFT BLANK NOTE This unit uses the vehicles horn as a sounding device In some installa tions the optional siren may have been used in place or or in addition to the vehicle horn as a sounding device Where siren chirps are referenced below the horn beeps may be substituted or in addition to ARMING THE SYSTEM ACTIVE 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press and release the Lock button on the keychain transmitter M R
12. he ignition key is turned on VALET SWITCH The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature and remote door locks will remain operational To use the valet mode the system must first be disarmed either by using your keychain transmitter or by activating your personalized manual override code Enter the vehicle and turn the ignition key to the on position Press and hold the valet pushbutton switch until the dash mounted LED turns on solid The system will remain in the valet mode To return to normal operation press and release the pushbutton switch any time the ignition is on Always remember to exit the valet mode This will ensure that the vehicle remains protected at all times MANUALLY OVERRIDING YOUR SYSTEM USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmit ter This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails If your system has been selected for Valet Switch manual override as indicated on the last page of this manual to by pass the alarm system 1 Open the vehicle door The alarm will sound 2 Turn the ignition key to the on position 3 Within 5 seconds press
13. n sounds one chirp If the siren did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual M Doors Lock Door locking during passive arming is a selectable feature The alarm can be programmed to allow the doors to lock only when arming using the keychain transmitter and they will not automatically lock during passive arming PROTECTION WHILE THE SYSTEM IS ARMED M Opening any protected door hood or trunk lid will cause the alarm to immediately sound The alarm will continue to sound for 30 seconds then stop and continue to monitor all protected entry points If the thief left a door opened the alarm will sound for six 30 second cycles remain armed and ignore that triggered zone M Whenever the system is armed the red dash mounted LED indicator will slowly flash This serves as a visual deterrent to the potential thief The LED is a very low current bulb and will not cause the vehicle s battery to drain even when left unattended for extended periods M Whenever the system is triggered the vehicle s parking lights will flash for the full 30 second alarm cycle attracting visual attention to the vehicle O OPTIONAL Whenever the system is triggered the interior courtesy lights will flash for the full 30 second alarm cycle O OPTIONAL Whenever the system is armed the vehicle s starting circuit will be bypasse
14. ny transmitter button other than the disarm button This action will turn off the siren yet leave the vehicle fully armed and protected This feature is partictularily useful if you are aware of children playing near your vehicle that may accidently trigger your security system In this case you can cancel the siren sounding without disarming your system INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle If an intrusion attempt has occurred the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered 1 If the LED is flashing one time pause one time pause etc then an intrusion attempt was made to the one of the pin switches typically installed under the hood or in the trunk or an optional sensor connected to the unit 2 If the LED is flashing two times pause two times pause etc then an intrusion attempt was made to a hood or trunk pin switch that was added to the system or to a light activated entry point if the alarm was installed using the voltage sensing feature 3 If the LED is flashing three times pause three times pause etc then an intrusion attempt was made through one of the vehicle s doors These intrusion warning indicators are stored in the system s memory and will only be erased when t
15. r Locks Required O OPTIONAL Courtesy lights turn on for 30 seconds or until the ignition key is switched on SILENT DISARMING 1 As you approach the vehicle press and hold the Unlock button on the keychain transmitter for 2 seconds M Red dash mounted LED turns off If passive arming was selected during the installation then the LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming M Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered M Siren will not sound If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered M Doors Unlock Using the optional Access Guard feature the alarm can be wired to unlock only the drivers door during this step To unlock all the doors press and release the Arm Disarm button of the transmiter a second time within 3 seconds Power Door Locks Required O Courtesy lights turn on for 30 seconds or until the ignition key is switched on WHILE THE SYSTEM IS SOUNDING If during a triggered state you wish to shut off the siren without disarming your security system simply press and release a
Download Pdf Manuals
Related Search