Audiovox P-956 User's Manual
Contents
1. IT Unsnap AT 2 PLACES EACH ON TOP AND BOTTOM PLASTIC FRAME FACTORY MOUNTING BRACKETS RADIO WIRING REFER TO PAGE 5 FOR SPEAKER WIRING AUTOMATIC ANTENNA VEHICLE 0 IMPORTANT FUSEBLOCK THE BLUE WIRE CAN BE USED TO REMOTELY ACTIVATE AN AUTOMATIC ANTENNA AN EXTERNAL AMPLIFIER SEE ANTENNA OR AMPLIFIER MANUAL EXISTING RADIO OR ANTENNA ACCESSORY FUSE CABLE PANEL BLACK METAL PART OF DASH ILLUMINATION DRILL HOLE IF PINK ELLY 522 THS WHE MUSTHE Ver T CONSTANT 12 VOLT SOURCE OF AANG WILL HGT OPERATE PROPERLY i TO SPEAKERS SEE SPEAKER H WIRING DIAGRAM POSITIVE TERMINAL A 12 VOLT BATTERY CHANGER PIN CONNECTOR _ CONNECTORS ANTENNA 10 CONNECTOR FUSE SPEAKER WIRING WARNING REFERTOPAGE4 THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS NEVER COMBINE BRIDGE OUTPUTS FOR USE WITH 2 SPEAKERS FOR RADIO WIRING NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO RCA JACKS LINE OUT FOR USE WITH OPTIONAL EXTERNAL AMPLIFIERS RED RIGHT WHITE LEFT j CALL 1 800 645 4994 FOR RECOMMENDATIONS OF MODEL CHANGERS THAT WILL WORK WITH YOUR RADIO DIN C2. all hardware and brackets as they will be used to mount the new radio 2 Carefully unsnap the plastic frame from the front of the new radio chassis Remove and discard the frame 3 Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio CAUTION DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS 4 Wire the new radio to the vehicle as per step 4 of the Universal Installation Procedure 5 Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1 Toll Free Installation Assistance The installation and wiring connections for this unit are so simple we doubt you ll need our help but if you do we re here to help you Just call our toll free telephone assistance line at 1 800 645 4994 during the days and hours shown U S A and Canada only TIME ZONE DAY MON FRI 5 30AM 4PM 6 30AM 5PM 7 30AM 6PM 8 30AM 7PM SATURDAY 6AM 2PM 7AM 3PM 8AM 4PM 9AM 5PM UNIVERSAL INSTALLATION USING MOUNTING SLEEVE EXISTING DASH OPENING FILE EDGES TO FIT IF NECESSARY DO NOT OVERFILE NOTE IF DASHIS SOLID USE MOUNTING SLEEVE AS A TEMPLATE amp CUT OPENING PERFORATED STRAP FASTEN THIS END TO SCREW STUD ON REAR OF CHASSIS MOUNTING SLEEVE FASTEN THIS END TO SECURE PART OF DASHBOARD DRILL HOLE IF NECESSARY REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UNSNAPPING
3. mounting sleeve into it If the opening is not large enough carefully cut or file as necessary until the sleeve easily slides into the opening Do not force the sleeve into the opening or cause it to bend or bow Check that there will be sufficient space behind the dashboard for the radio chassis 3 Locate the series of bend tabs along the top bottom and sides of the mounting sleeve With the sleeve fully inserted into the dashboard opening bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard 4 Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit After completing the wiring connections attach the front panel and turn the unit on to confirm operation ignition switch must be on If unit does not operate re check all wiring until problem is corrected Once proper operation is achieved turn off the ignition switch and proceed with final mounting of the chassis 5 Carefully slide the radio into the mounting sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place 6 Attach one end of the perforated support strap supplied to the screw stud on the rear of the chassis using the hex nut provided Fasten the
4. ABLE SUPPLIED OPTIONAL CD CHANGER WITH CD CHANGER TELEPHONE A 8 PIN DIN SOCKET FOR CONNECTION TO MUTE CD CHANGER ADAPTER CABLE GRAY ISO TO 8 PIN DIN SOCKET CD W CONNECTORS CHANGER ADAPTER CABLE PART NUMBER P956CDC SUPPLIED SEE PAGE 6 FOR DETAILS 8 PIN PLUG 8 PIN PLUG LEFT FRONT SPEAKER SEE PAGE 4 RIGHT FRONT SPEAKER FOR RADIO WIRING l l s VIOLET Satna N ES G w BLACK STRIPE VIOLET w BLACK STRIPE HELP TTA LEFT REAR SPEAKER 1 8 0 0 6 4 5 4 0 9 4 RIGHT REAR SPEAKER Monday Friday 8 30am 7 00pm Eastern Saturday 9 00am 5 00pm Eastern CD CHANGER ADAPTER CABLE REFER TO PAGE 5 FOR OPTIONAL CD CHANGER CONNECTIONS To Radio CDC ISO 8 Pin Adapter Cable ONKOL a CD Left Input Wht 1 2 3 12 Volts Yel Er CD Data Bus Brn CD Audio Grd Shld JSA 6 7 8 SEENE Data Bus 519 5 CD Right Input Red 6 8 Pin ISO Connector 7 Control Voltage Blk 8 CDC On Grn Es 5 2003 AUDIOVOX ELECTRONICS CORP HAUPPAUGE NY Printed in China 128 6839
5. by AUDIO INSTALLATION MANUAL CD R RW PLAYBACK 7 CDC Control 7 BAND s SCAN LOUD TUNE 7 TRACK P SCAN lt Pau 2 son 3 RPT 04 5 cd 0 6 Released 7 14 03 956 P956G AM FM MPX RADIO WITH DETACHABLE FRONT PANEL COMPACT DISC PLAYER CD CHANGER CONTROLS AND QUARTZ CLOCK DIGITAL AUDIO INSTALLATION INSTRUCTIONS This unit is designed for installation in cars trucks and vans with an existing radio opening In many cases a special installation kit will be required to mount the radio to the dashboard These kits are available at electronics supply stores and car stereo specialist shops Always check the kit application before purchasing to make sure the kit works with your vehicle If you need a kit but cannot find it available call our toll free HELP line at 1 800 645 4994 UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE 1 Remove the detachable front panel if it is attached to the chassis by pushing the Release button Slide the mounting sleeve off of the chassis If it is locked into position use the removal tools supplied to disengage it 2 Check the dashboard opening size by sliding the
6. other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided Bend the strap to position it as necessary CAUTION The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration 7 Re attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit INSTALLATION USING KITS 1 If your vehicle requires the use of an installation kit to mount this radio follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit Wire and test the radio as described in Step 4 of the installation procedure Install the radio mounting plate assembly to the sub dashboard according to the instructions of the installation kit Attach the support strap to the radio and dashboard as described in Step 6 above Replace the dashboard trim panel N ISO INSTALLATION PROCEDURE This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota Nissan Mitsubishi Isuzu Hyundai and Honda vehicles to mount the radio to the dashboard Please consult with your local car stereo specialist shop for assistance on this type of installation 1 Remove the existing factory radio from its dashboard or center console mounting Save
Download Pdf Manuals
Related Search